Untitled - DirectedDealers.com
Contents
1. 30 2010 Directed Electronics All rights reserved Glossary of Terms Document Terminology Control Module Remote Control Control Center Status LED Control Button The brain of your system Usually hidden underneath the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the system s func ions A handheld remote control which operates the various func ions of your system The control center contains the system s radiofrequency an enna the control button and the Status LED For maximum remote control range the control center is usually located at he top of the windshield centered near the rearview mirror A light used to indicate the status of your system It is located on your system s Control Center A small push button located on your system s control center lt is used to override disarm the alarm when a remote is not available or to enter or exit Valet Mode 2010 Directed Electronics All rights reserved 31 Government Regulations This device complies with Part 15 of FCC rules Operation is subject to the fol lowing two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of2. Number of presses 1 Turn the ignition On 2 Press the control button on the Control Center the correct number of times the default is 1 press 3 After a few seconds the siren output ceases and the system is disarmed Note Asa precaution if programmed for Passive Arming or Auto re arming the system should be placed into Valet Mode until a remote is available Trigger Zone Fault Report When armed by remote command the system runs a status check of the alarm trigger zones Faulty zones usually caused by dome light delay or open trunk are bypassed and reported via the control center LED while all other trigger zones remain active and are monitored to protect the vehicle Should a faulty zone self correct dome light turns off it becomes active and is then monitored normally The siren chirps once again a few seconds following the arming chirps as an audible alert the control center LED flashes in groups to indicate the zone number 2010 Directed Electronics All rights reserved 19 Alarm Report If the alarm was triggered while armed it will be reported when he alarm is disarmed via siren chirps parking light and control center LED flashes The siren chirps 4 times or 5 times if NPC On the park ing lights flash 3 times and the control center LED flashes in groups to indicate the last two zones that were triggered see Table of Zones The report output will repeat for each disarm operation until the igni
3. Remote Valet S Press and release Enters or if On exits Valet Mode The Control Center LED turns on and off accordingly 2010 Directed Electronics All rights reserved 11 Timer Start j Press and release Activates or if On deactivates Timer Start The parking lights flash quickly four times for On and slowly four times for Off Note System needs to be armed or Timer Start will not start the engine AUX 2 Press and release AUX Activates or if On deactivates the Aux 2 output See Advanced Start under Remote Start Features for more details 12 2010 Directed Electronics All rights reserved Advanced Commands Level 3 Press and release the f button 3 times The transmit LED illuminates in sets of triple flashes to indicate Level 3 Sensor Silent Arm Press and release The alarm arms doors lock and the siren chirps and parking lights flash 3 times Car finder Press and release S The siren emits one long chirp and the parking lights flash for 10 sec onds The parking light flashes stop if armed or disarmed while Car Finder is in progress Smart Start Press and release Activates or if On deactivates Smart Start The parking lights flash quickly five times for On and slowly five times for Off Note System needs to be armed or Smart Start will not start the engine AUX 3 Press and release AUX Activates or if On deactivates the Aux 3 outp
4. Key Takeover 1 Disarm the system and enter the vehicle do not step on the foot brake 2 Insert the key turn it to the run position and then step on the foot brake the remote start then turns off 3 The parking lights turn off to indicate remote start is off 4 The vehicle is ready to drive 2010 Directed Electronics All rights reserved 21 Remote Start Safe lock Remote start safe lock makes sure the doors are locked while the en gine is running and after even if they are unlocked when remote start is activated Door locks may require additional parts and labor Disabling Remote Start Remote start can be disabled by moving the Toggle Switch to the Off position If remote start is attempted while Off the engine will not start See Remote Start Fault under Remote Start Features move the switch back to the On position to resume normal operation Advanced Start The Advanced start features Timer Start and Smart Start will automati cally start the engine to maintain battery charge or combat extreme cold when parked for an extended period of time Precautions for the Advanced Start features e Park the vehicle in a well ventilated area away from windows and doors that lead into inhabited spaces e Arm and Lock the vehicle the engine will not start unless the doors are locked e Only one Advanced start feature can be enabled at any given time e For manual transmission vehicles MTS mode must be enable
5. back to a previous menu press and release the f button When programming is exited the transmit LED turns off Remote Pairing The following instruction will step you through the remote pairing op eration Prepare the vehicle system for pairing 1 Open at least one of the vehicle s doors 2 Turn the key to the ON position 3 Within 5 seconds press and release 1 time the Control button on the Control Center 4 Within 5 seconds press and hold the Control button The status LED will flash one time and the siren will chirp once to confirm the system is ready for remote pairing 5 Release the Control button and proceed to next step Pairing will exit if e Step 7 is not completed within 60 seconds e The doors are closed The ignition is turned off 2010 Directed Electronics All rights reserved 15 Prepare the remote control for pairing 6 Enter programming to access the Main Menu Z7 Press and hold the button for 1 second 3 transmit LED flash es indicate the remote control is ready to pair 8 Press the button The siren will chirp to confirm the system has learned the remote con trol Remote Features From the main menu press the S button to access the remote opero tion features 2 transmit LED flashes indicate the remote features menu is accessed Press the buttons indicated in the tables below to set the feature option The remote control will flash the Transmit LED to indicate the se
6. seconds the system re arms itself and ocks the doors Auto Re arming Auto re arm ensures the vehicle stays protected if it is not entered after disarming by remote control After disarming by remote the alarm automatically re arms itself and locks the doors if programmed on in 30 seconds Open any point of entry to stop the re arm until the next disarm by remote Onetime Bypass Turn the ignition On for one to three seconds and then Off The siren chirps once to confirm onetime bypass is enabled Onetime bypass can be used to temporarily bypass the Passive arm ing operation for one cycle It also bypasses the comfort closure and auxiliary channel outputs if programmed to activate when arming After the next disarm all operations return to normal These features must be turned on by an authorized Directed dealer 26 2010 Directed Electronics All rights reserved Valet Mode Valet mode can be entered and exited by performing the Remote Valet command or manually using the vehicle key and the control button When entered the alarm functions are defeated while the conve nience features still operate normally Use the following steps fo manually enter and exit Valet Mode 1 Turn the ignition switch On and then Off 2 Immediately press and release the control button once 3 The control center LED turns On when entering and Off when exiting Power Save To reduce power consumption the control center status LE
7. warranty from the da ECEIVED BY DIRECTED FOR WARRANTY REPAIR AUTHORIZED DEALER WILL BE DENIED ically void if the unit s date code or serial has been modified or used in a manner he uni led purpose the uni of the uni EXTENT TO EXPR TY FITNE TOF THER ASSUMES T ANY D IS DI L ACTS LERS D AGAINST SURANCE AGAIN S OR CONTE EVER INCLUDING R VANDA TENANC ILI SS FOR OF THI R NTELLECTI UTY OB RECTED DISC ECTED SI POSSIBLI LISM TH E REMOVAL OR RE has been damaged by accident unreasonable other causes not arising out of defects in he unit caused by determine what con excessive damage MES INCLUD TY WARRA D WARRANTY wil wit LAW ALL WARRA TY IMPLIED WARRA PARTICULAR PURPOSE A UAL PROPERTY ARE EXPRESSLY EXCLUDE OR AUTHORIZES ANY PERSON OR LIGATION OR LIABILITY IN CO LAIMS AND HAS ABSOLUTELY RD PARTIES INCLUDING ITS A ECURITY SYSTEMS INCLUDING E THEFT DIRECTED IS NOT O ST VANDALISM DAMAGE OR TH TS AND HEREBY EXPRESSLY DISCLAIMS Al WITHOUT LIMITATION LIABILITY FOR THEFT S WARRANTY DOES NOT COVER LABOR STALLATION OF THE UNIT OR s sole discretion h 925 29 LU E T CTIO AB cm O UTH TH FFE EFT OF R U G T O S R pao H m Y THE HAS USE CAU Some states do exclusion or limi specific legal rights Th
8. 1 WAY PYTHON SECURITY FOR THE BEST Congratulations Congratulations on the purchase of your state ofthe art remote start and security system Reading this Owner s Guide prior to using your system will help maximize the use of your system and its many fea tures Please visit the below website htto www pythoncarsecurity com For general and additional guide information For any ad ditional questions please contact your authorized Directed dealer or contact Directed at 1 800 753 0600 What you get Welcome to the best generation of security with remote start Your system contains everything you need e Two l way SuperCode remote controls e Owner s guide e Warranty card Important information Government Regulations and Safety information A Read the Government Regulations and Warning Safety First sections of this manual prior to operating this system Warning Failure to heed this information can result in death personal injury or property damage and may also result in the illegal use of the system beyond its intended purpose Your Warranty Your system comes with a warranty Please make sure you receive the warranty registration card and proof of purchase from your dealer indicating the product was installed by an authorized Directed dealer Please validate it online at www prodregister com directed or com plete and return the warranty registration card Replacement remote controls If addi
9. Aas n jr anye a sad e 14 W orng annan a E E a 4 Remote Control Configuration Remote Programming ala Remote Paining isssssccssssssssaasssassaasseanstasnsasnasesasacreasacsdosgeasesbtasadeeads ene Remote Features Sensor Adjust Alarm Features a Normal Arm Protection ssssssssstenssosssonstessstsesesstiissncsseacseessensieesss 18 Sensor Silent Arm protection i sssccsczsesasceserwsccacessactenceesssecescassaates canes 18 Sensor Warisaway GUIpUl y y s yax y5x5 kala AK e E ESETA SE ENa RAEES 19 Full Trig Ger Outptiea cis sus 544552456 exyan n n RANA Ani n da kan HaWA K dawa Gawa Z N 19 Emergency Overrides isk anina nay n n bidn bi H nan V i si san d04 28 05 19 Trigger Zone Fault Report sss k sada kala ciniya nasian ban aka ndkao kan ae VEK n 19 Wan Sc gx og___ am 20 Nuisance Prevention NPC 20 Remote Start Features Pit Stop Mode Wall DD Dd Remote Start Safe lock Disabling Remote Start TON SHE cc ND ND N Manual Transmission Start MTS mode E e 23 Turbo Timer Mode UUU 24 Remote Start Faults Remote and System Operations Passive Arming 26 Auto Re arming 26 Valet Mode DDDDDDrnrnrz_breoe2gxx owrrr 27 Power SAVE cc scsertresseeeancdutesasneysceaineevabsyede vet SERAN ERA EAEEREN EN 27 Rapid Resume 27 Car Select s27 System Expa
10. D modifies its output if the vehicle is parked for an extended period If Armed the flashing is reduced after 24 hours When Valet mode is On the LED turns off after 1 hour and resets each time the ignition is turned off Rapid Resume If power is ever disconnected by a mechanic or thief the system will resume the state it was in at the time of disconnection when power is reconnected Car Select Car 2 remote control option must first be turned On See Remote Control Configuration section to turn on Press and hold the f button for 3 seconds The LED flashes once or twice to indicate the selected Car is 1 or 2 release the button for Car Select or continue to hold for programming Release the f button then press and release while the LED flash es continue lo perform Car Select Once the car is selected a com mand can be performed by pressing one of the command buttons 2010 Directed Electronics All rights reserved 27 System Expansion Options Controlling two vehicles Car Select The remote controls can control systems in two different vehicles sav ing the need for multiple remote controls This feature also allows for customized system configurations on each vehicle that has more than one driver See Owner Recognition for details Owner recognition The system can be configured to recognize the remote used when disarming and change selected features to match the remote users preferences Memory seat adjustment sir
11. DENT U THE EVENT OF A CLAIM E SHALL BE IA STATE LAWS PUTE THE LL BE STRICTLY OF THE UNIT ATSOEVE CIDE LOSS UNITY AND 1 DOES OFFER LE SUBJECT T VOID IF THE U AUTHORIZED DIRECT REASONABL CE OR OTHE STRUCTIO will las CALIFOR HA Z QE F TIME C O gt im OA 7m he or vary from State to State ates of America and or Canada are sold information of Directed products please visit the at www directed com This product may be covered by a Guaranteed Protection Plan GPP See your authorized Directed dealer for detai 1 800 876 0800 2010 Directed Electronics All rights reserved s of the plan or call Directed Customer Service at 920 1001 1 01 2011 06 37
12. arter Kill The Failsafe starter kill relay prevents the engine from starting Note May require additional parts and installation Sensor triggers The onboard shock sensor can distinguish minor im pacts from major impacts to the vehicle exterior Minor impacts causes the system to emit a Warn away output Major impacts caused for example by a forcible entry attempt results in a Full Trigger output Point of entry triggers Opening the hood or trunk causes a Full Trig ger output while opening a Door or turning on the Ignition causes the the siren to chirp 3 seconds before beginning the Full Trigger output This 3 second delay allows time to disarm and silence the siren in case of accidental trigger Sensor Silent Arm protection Sensor Warn away and Sensor Full Trigger activations are defeated Point of entry triggers will activate the Full Trigger output Full Silent Arm Protection Sensor Warn away Sensor Full Trigger and Point of Entry activations are defeated Only the Ignition input will activate the Full Trigger out put 18 2010 Directed Electronics All rights reserved Sensor Warn away output When the system sensors detect a Warn away trigger the siren chirps and parking lights flash for 3 seconds Full Trigger output An alarm Full Trigger will sound the siren and flash the parking lights for 30 seconds Emergency Override The following procedure disarms the system when a programmed re mote is not available
13. brake and leave the engine running For Pit Stop or Turbo Timer mode io leave the engine running after arming open the driver door Release the foot brake if pressed during Step 1 or press and release the foot brake anytime As long as the engine is running there is no time limit to perform this step Within 20 seconds of foot brake release press any command 2010 Directed Electronics All rights reserved 23 button on the remote after 20 seconds return to Step 2 For Turbo Timer Mode press the optional dash mounted activation button or send the Timer Mode command 4 The parking lights flash 5 times to confirm MTS mode is enabled and the remote start activates the ignition outputs 5 Turn Off and remove the key from the ignition switch the engine remains running 6 Exit the vehicle close all the doors and arm the system 7 The engine turns off If the door is opened in Step 1 then the engine continues fo run Turbo Timer Mode The system keeps the engine running for the Turbo Timer runtime and can be activated by remote control or optional dash mounted activa tion button 1 With the engine running set the parking brake 2 Press the optional dash mounted activation button or perform the Timer Mode command 3 The parking lights turn on and the remote start activates the igni tion outputs 4 Turn Off and remove the key from the ignition switch the engine emains running 5 Exit the vehicle close al
14. confirmation chirps are programmed off the system will still emit one chirp as an alert when disarming 1 Using a small flathead screwdriver insert into slot located at the bottom of the keypad and carefully pry the front of the unit open 2 Turn both the unit front and circuit board over remove battery from clip and replace 2010 Directed Electronics All rights reserved 29 Note Verify that the battery polarity is correct when replacing 3 With the front and circuit board still turned over turn back portion of unit onto both parts reposition all parts and snap together Battery Disposal Directed Electronics cares about the environment If you KI need to dispose of the battery please do so in accordance 3 with your municipal requirements for battery disposal or re urn to Directed Electronics at One Viper way Vista CA 92081 Shipping and or handling costs are the sole responsibility of the owner sender and will not be covered by Directed Electronics This product is covered by one or more of the following United States patents Remote Start Patents 5 349 931 5 872 519 5 914 667 5 952 933 5 945 936 5 990 786 6 028 372 6 467 448 6 561 151 7 191 053 7 483 783 Vehicle Security Patents 5 467 070 5 532 670 5 534 845 5 563 576 5 646 591 5 650 774 5 673 017 5 712 638 5 872 519 5 914 667 5 952 933 5 945 936 5 990 786 6 028 505 6 452 484 Other patents pending
15. d before Timer Start or Smart Start can be activated Timer Start operation Activation begins a countdown timer as set by the installer de fault 3 hours When the timer expires the engine starts When the Remote start runtime expires the engine shuts off and the countdown timer restarts This will repeat as many times as set 22 2010 Directed Electronics All rights reserved by the installer default 6 starts Timer Start is exited after the final start Smart Start operation Smart Start uses the settings for Timer Start in addition to tempera ture and battery level to automatically start the engine Activation begins the countdown timer When the timer expires the vehicle interior temperature and battery level is checked and if the Tem perature is above 100F below OF or the battery level is be low 10 5y the engine will start When the Remote start runtime expires the engine shuts off and the countdown timer restarts Smart Start is exited atter the final start Note The temperature and battery thresholds can be changed by an authorized Directed dealer if a higher or lower threshold is desired Manual Transmission Start MTS mode When installed into a manual transmission vehicle the system requires that the MTS mode is properly set when parking If MTS mode is not properly set or is defeated after being properly set the system will not start the engine 1 3 With the engine running set the parking
16. e control center LED generates a Trigger Zone Fault report To Arm and Panic Press and hold The alarm Arms or Locks in Valet and after 2 seconds sounds the siren and flashes the parking lights Press the or button to stop the output Disarm Press and release The alarm disarms doors unlock if connected and the siren chirps and parking lights flash twice An Alarm Report alert of 4 or 5 siren chirps will replace the normal disarm chirps if the alarm was triggered 2010 Directed Electronics All rights reserved Remote Start Press and release Activates or if On deactivates the remote starter The engine and parking lights turn On or the engine and parking lights turn Off ac cordingly If a Remote start configuration issue prevents the engin from starting the parking lights flash a Remote Start fault report to identify the fault AUX Trunk Press and hold AUX The Trunk opens if connected when this button is pressed for 2 sec onds See Remote and System Operations for details See Alarm Features for details See Remote Start Faults under Remote Start Features for details For Manual transmission vehicles see Manual Transmission Start in the Remote Start Features section for more details 2010 Directed Electronics All rights reserved Advanced Commands Level 1 Press and release the f button 1 time The transmit LED illuminates in sets of single fla
17. ed by an authorized Directed dealer in accordance with the Safety Check outlined in the product installation guide If the vehicle starts in gear cease remote start operation im mediately and consult with the authorized Directed dealer to fix the problem After the remote start module has been installed contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide If the vehicle starts when performing the Neutral Safety Shutdown Circuit test the remote start unit has not been properly installed The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear All installations must be performed by an authorized Directed dealer OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN 34 2010 Directed Electronics All rights reserved GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION OPER ATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY YOU MUST IMME DIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS This product is designed for fuel injected vehicles only Use of this product in a standard transmission vehic
18. en chirps passive arming remote button auto unlocking alarm output duration can all be custom set for each remote user at the time of installation Comfort closure Comfort Closure emulates turning the key in the door cylinder or hold ing the lock button of an OEM keyless entry It will automatically close the windows and sunroof on vehicles with this type of OEM conve nience feature Alarm output duration The length of time the siren sounds can be adjusted from 1 to 180 seconds at the time of installation Arming and Warn away chirp control The system Arm Disarm and Sensor Warn away chirps can be config ured for those that prefer a custom silent alarm operation Driver door priority unlocking The door unlocking operation can be configured to emulate an OEM style of driver priority unlocking for added security during disarming These features must be turned on by an authorized Directed dealer 28 2010 Directed Electronics All rights reserved The remote controls are powered by 1 coin cell battery CR 2032 that can be purchased at most retailers When the battery begins to weaken the operating range will be reduced The information and precautions in this section can help maximize your battery s life and usage in providing you with many years of trouble free operation Low Battery Alerts When disarming the system using a remote with a low battery the siren will emit one additional chirp as an alert If
19. in the following Basic command and Advanced command sections Performing Commands Perform Basic commands by pressing a Command button Perform Advanced Commands by first accessing Levels 1 4 using the f button and then by pressing a Command button while within a level Advanced command example Silent Arm 1 Press the f button once to access Function level 1 The trans mit LED single flashes for 3 seconds 2 Press the bution while the transmit LED is still flashing to perform the Silent Arm command 3 The system will arm lock the doors and flash the parking lights without siren chirps 2010 Directed Electronics All rights reserved Remote Control Command table Level Direct Access fx Fx 2 Fx 3 fx4 Ru LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 Arm lock Silent Arm Sensor Sensor Silent Full Silent Panic Bypass Arm Arm Disarm Unlock Silent Disarm Remote Valet Car Finder fy Remote Start Runtime Timer Start Smart Start Defogger Reset AUX Aux Trunk AUX 1 AUX 2 AUX 3 AUX 4 f Advance Level Enter program ming 8 sec 2010 Directed Electronics All rights reserved Basic Commands Direct Access Arm Press and release The alarm arms doors lock if connected and the siren chirps and parking lights flash once If Valet mode is On the doors lock without siren chirps the alarm is disabled Exit Valet mode to arm the alarm normally If a trigger zone fault is detected the siren chirps once again and th
20. ion is turned on See Nuisance Prevention NPC for more details Table of Zones Zone led flashes Zone Name Trunk Shock Sensor Door Sensor 2 Ignition Hood O nA BR WN Nuisance Prevention NPC NPC monitors all alarm zones and if any are triggered excessively bypasses them until corrected If a point of entry trunk hood door is left open following a forced entry it is bypassed It becomes active again only after being closed Bypassed sensors automatically reset after one hour and after the vehicle is driven Disarming then re arming the alarm does not reset bypassed sensors 20 2010 Directed Electronics All rights reserved Remote Start Features Pit Stop Mode lo exit vehicle with engine running The system keeps the engine running during short trips into the house or convenience store To perform Pit Stop 1 With the engine running set the parking brake and release the foot brake 2 Press the button the parking lights will turn on to indicate remote start is on 3 Turn the key to off and remove it from the ignition the engine continues running for the programmed runtime 4 Exit the vehicle and arm the alarm Note For Pit Stop on manual transmission vehicles follow the direc tions in the Manual Transmission Start MTS mode section Key Takeover When you are ready to drive The system keeps the engine running until the vehicle is ready to be driven To perform
21. is warranty is in Canada Produc ASS and sha For further detai DEAL EGO PP IMR TO DS G ES ji Cc E S O OT B R OR IF TI EGLIGE ES NOT ARISING OUT OF DEFECT IN MATERIALS OR CO ow limitations on how long an implied warran ation of incidental or consequential damages This warranty gives you and you may also have other rights tha product s within the United S s sold outside of the United States of America have NO WARRANTY express or implied PUT LICA DAMAGE TO RCIAL LOSS LOSS OF NG THE ABOVE TI EPLACE OR REPAIR TI TWI TED WARRA DITI EQUENTIA TE INVOLV COUNTY BLE FEDERAL ECOVERY U H B All U L NOT NOT l B IM COMME HSTA R DESCRIBED lo E not al only valid for sale o s relating to warran support section of Directed s website L DAMAGES OF A NG DIRECTED OR ITS SUBSI IN THE STATE OF CAL LAWS SHALL AP DER ANY CLAIM AGAI THE AUTHORIZED DIRECTED DEAL E RESPONSIBLE TED TO Al VEHICLE DAMAGES HASED FROM DIRECT T HAS BEE ACTS OF GOD NEGLECT IMPROPER SERVI Y KIND FOR AND ST PU IA PLY D ER S FOR Al SEQUENTI FOR TH ECONOMI HE MA Y CO DIARY THE VENU GOVERN THE DIS RECTED S RCHASE PRICE Y DAMAGES WH IAL DAMAGES E LOSS O C OPPORT UFACTURER HE CO S WA D OR A HEREIN TH E TROL MOD RRANIY IS DAMAGED BY ACCI
22. l the doors and arm the system 6 The engine runs for the Turbo Mode runtime Note Turbo Timer must be turned on by an authorized Directed dealer 24 2010 Directed Electronics All rights reserved Remote Start Faults For user safety the system must be properly configured or remote start will not activate A Remote Start Fault may be caused by any of several configuration issues Refer to the table below for the command type and parking light flashes that will identity the configuration issue and solution Flashes Possible Fault Solution 5 Brake on Release foot brake 6 Hood open Close hood 7 After performing Remote Start Enable MTS mode command MTS not enabled After performing Timer Start or Check all Solutions Smart Start command 8 Toggle Switch off Turn switch on None Alarm is triggered Disarm or reset alarm Refers to the number of parking light flashes 2010 Directed Electronics All rights reserved 25 Remote and System Operations Passive Arming Park and exit the vehicle after the doors are closed the Passive arm ing countdown begins The led flashes quickly and upon reaching 20 seconds the siren then chirps once At 30 seconds the system arms itself Anytime before the system arms you can re enter the vehicle or open the trunk fo load or unload items and after closing passive arm ing resumes To stay secure in case of accidental disarming the system if a door is not opened within 30
23. le must be in strict accordance with this guide This product should not be installed in any convertible vehicles soft or hard top with a manual transmission Installation in such vehicles may pose certain risk Interference All radio devices are subject to interference which could affect proper performance Upgrades Any upgrades to this product must be performed by an authorized Directed dealer Do not attempt to perform any unauthorized modifica tions to this product Water Heat Resistance This product is not designed to be water and or heatresistant Please take care to keep this product dry and away from heat sources Any damage from water or heat will void the warranty 2010 Directed Electronics All rights reserved 35 Kyo Limited lifetime consumer warranty Directed Electronics Directed promises to the original purchaser to repair or replace at Directed s election with a comparable reconditioned model any Directed unit hereaF ter the unit exclud sensors and accessories which reasonable use during the lifetime of the vehicle provid the unit was purchased from an authorized Directed installed and serviced by an au hicle in which it was originally i o Directed shipping ated proof of purchase bearing the following information consumer s reinstalled in the ve dealer and the unit bill of sale or other d name telephone nu and address comp ing without horized is re
24. nsion Options 28 Battery Information 27 Low Battery Alerts 29 Battery Replac menit scssssscscsessonsssacsasiscssscvsscsaoteacsinconsenevancssnensbniies 29 Peter y Disposell orasi Nazan Ka RA KECE E EE ot AWE And kan N 30 Patent Information z Glossary of Terms Government Regulations Warning Sofety First Installation 2 Remote Start Copoble 33 Manual Transmission Vehicles 33 lnterference Upgrades Water Feq Resistance winccccsicsseccnvostvesencesuaseussetwantwseseastvarseasdvancteonterse 35 Limited lifetime consumer warranty erer erkeke eee ereke 36 Getting Started Keys fo using this manual Specific actions in bold type and style conventions are used consis tently throughout this manual they are as follows Press implies pushing in and releasing a button e Hold is used after Press actions when a button needs to be held in position for an extended period of time typically several sec onds e Italicized words denote section sub headings in this guide and can be located through the table of contents e An asterisk when used after a word or phrase denotes that additional details can be found in related sections usually noted at the bottom of the page or end of the section 2010 Directed Electronics All rights reserved Remote Control Inte
25. ponsible for compliance could void the user s authority to operate this de vice 32 2010 Directed Electronics All rights reserved Warning Satety First Please read the safety warnings below before proceeding Improper use of the product may be dangerous or illegal Installation Due to the complexity of this system installation of this product must only be performed by an authorized Directed dealer If you have any questions ask your retailer or contact Directed directly at 1 800 753 0600 Remote Start Capable When properly installed this system can start the vehicle via a command signal from the remote control transmitter Therefore never operate the system in an enclosed area or partially enclosed area without ventilation such as a garage When parking in an enclosed or partially enclosed area or when having the vehicle serviced the remote start system must be disabled using the installed menu wheel It is the user s sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle THE USER MUST IN STALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE ALL DOORS LEADING FROM ADJACENT LIV ING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STOR AGE AREA MUST AT ALL TIMES REMAIN CLOSED These precautions are the sole responsibility of the user Manual Tran
26. rnal Antenna Transmit LED a r Buttons Function Button Feature Description Internal Antenna Used for transmitting information Transmit LED Active when transmitting information Command buttons 4 Used to perform arming disarming auxiliary channel and remote start commands Function button Used to access function levels for commands configuration menus for programming and Car Selection 2010 Directed Electronics All rights reserved Control Center Control button Antenna A ENBER Status LED The Control Center typically located on the upper part of the front windshield It consists of e The In vehicle system antenna e The Status LED as a visual indicator of the system s status e The Control button for placing the system into Valet Mode and to perform the Emergency Override operation See Remote and System Operations section for details See Alarm Features for details 2010 Directed Electronics All rights reserved 5 Using your System Commanding the system Commands Basic or Advanced are used to activate system features and are performed by pressing one of the Command buttons Basic commands control the most often used security and remote start fea tures while Advanced commands control more specialized features Contirmations for Basic or Advanced commands are indicated by siren chirps and parking light flashes A description of each feature confirmation is found
27. shes to indicate Level 1 Silent Arm Press and release The alarm arms doors lock if connected and the parking lights flash once Silent Disarm Press and release S The alarm disarms doors unlock if connected and the parking lights flash twice The Silent Disarm output may be replaced by the Alarm Report Runtime Reset Press and release f more time is needed while remote start is active runtime reset wil eset the runtime counter fo the pre programmed setting Note Remote Start must be On to use this feature AUX 1 Press and release AUX Activates or if On deactivates the Aux 1 output See Alarm Features for details 10 2010 Directed Electronics All rights reserved Press and release the f button 2 times The transmit LED illuminates in sets of double flashes to indicate Level 2 Sensor Bypass Press and release Performing the Sensor Bypass command will incrementally bypass sen sor operations and be confirmed as follows e Warn away bypass The Parking lights flash 2 times Sensors will be activated for Full Trigger levels of impact only e Warn away amp Full trigger bypass The Parking lights flash 3 times Sensors will not be activated for any level of impact e Sensor Bypass off The Parking lights flash 1 time Sensors are fully operational Note System needs to be armed to perform Sensor Bypass Perform arm command any time to turn Sensor Bypass Off
28. smission Vehicles Remote starters on manual transmission vehicles operate differently than those with automatic transmission because you must leave your car in neutral You must read this Owner s Guide to familiarize yourself with the proper procedures regarding manual transmission remote starters If you have any questions ask your authorized Directed dealer or contact Directed at 1 800 753 0600 2010 Directed Electronics All rights reserved 33 Kyo Before remote starting a manual transmission vehicle be sure to e leave the vehicle in neutral and be sure no one is standing in front or behind the vehicle Only remote start on a flat surface e Have the parking brake fully engaged WARNING It is the responsibility of the owner to ensure the parking emer gency brake properly functions Failure to do so can result in personal injury or property damage We recommend the owner have the parking emergency brake system inspected and adjusted by a qualified automotive shop biannu ally Use of this product in a manner contrary to its intended mode of operation may result in property damage personal injury or death 1 Never remotely start the vehicle with the vehicle in gear and 2 Never remotely start the vehicle with the keys in the ignition The user must also have the neutral safety feature of the vehicle periodically checked wherein the vehicle must not remotely start while the car is in gear This testing should be perform
29. the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency en ergy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television which can be determined by turning the equipment OFF and ON the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with the Industry Canada Radio Standards Specification RSS 210 lts use is authorized only on a no interference no protection basis in other words this device must not be used if it is determined that it causes harmful interference to services authorized by IC In addition the user of this device must accept any radio interference that may be received even if this interference could affect the operation of the device WARNING Changes or modifications not expressly approved by the party res
30. tional remote controls P N 7153P are desired please see your authorized dealer or visit us at www directedstore com to order Contents Getting Stated n sy l ye Eek K WEKA NM ageuersadccsstereeantetneesteevnnenese aye 3 Keys to using this manual lt 3 Remote Control 4 Using your Systemvi scisisesscssssteesssesstsnestesessesestscssasissasespasteorstseestossatersstsessteceiects 6 Commanding the systemteori k r nab kan a sikand daka a ra dikan na 6 Performing Commands 6 Remote Control Command table car7 Basic Commands Direct Access erkeke keke keke keke k x ke keka 8 ALI ey keva kar keka kuya saya Kak bd ke RAN WA K k ka Vu Kaka HARA RA ARA W HERAN A RS d k dR AE RANA 8 Runtime Reset Advanced Commands Level 2 ccccccsesessescssecessseesssescseecsseecsssecssseessscesestenes 11 Sensor Bypass 1 Remote Valet Dila Do nd AUX Zieccccceseetes tava aus uavnnas snesblenungauat wend deweaewbacandeesd beadeaseseaisasisenisesieans Advanced Commands Level 3 13 Sensor Silent Arm 13 Smar SHOT cy 1sa eye a l 4413443054154500 b d OO V Be KEWE BEM W o EROAREN SEE 13 AUX Beds ceeds ore ckve cacevase cave nad iaauehan aeneaes n tannin teen rm 3 Advanced Commands Level 4 14 Full Silent Arm 14 Defogger ae sam sae dene oe dak e s ew RE Her eo WAN e a rne da
31. tting Feature Button Press Single Flash Double Flash Keypad Lock Aulo Off No function No function No function Car 2 9 Car 2 On Car 2 Off Indicates default setting Keypad Lock Options Off Auto When Off the buttons do not lock and always perform a com mand when pressed VVhen set to Auto the remote buttons lock after a 20 second lapse between button presses to prevent unin tentional operations 16 2010 Directed Electronics All rights reserved To unlock the buttons press the f button followed by the S button Note When the Keypad is locked the remote control may ap pear to be non operational It will not transmit a command or illuminate the Transmit LED and needs to be unlocked to resume normal operation Car 2 Options Off On The remote controls can control two systems independently When set to Off the Car Select feature is not available When set to On the Car Select feature is enabled See Car Select un der Remote and System Operations for detail on using a remote with 2 systems Sensor Adjust The button is used for sensor adjustment to avoid unintended alarm triggers it is recommenced that an authorized Directed dealer performs all sensor adjustments 2010 Directed Electronics All rights reserved 17 Alarm Features Normal Arm Protection Status LED The Control Center Status LED flashes as a visual indicator that your vehicle s security system is active St
32. turned mber and address ete product descrip imitation the siren the remote transmitters the associated proves to be defective in workmanship or material under ed the following conditions are met dealer the unit was professionally Directed dealer the unit will be profession ally nstalled by an authorized Directed prepaid with a legible copy of the he authorized dealers name telephone number ion including accessories the year make and model of the vehicle vehicle license number and vehicle identification number All com ponents other than t ana purchase of the same ALL PRODUCTS R HOUT PROOF OF PURCHASE FROM A ransferable and is automa WIT This warranty is non number is defaced contrary to its intend use neglect improper service installation or s or construction The warranty does not cover damage to Directed in i es excessive damage and may refuse the return of any uni ALLOWED BY ESS WARRA materia installati stitu TOT BUT OF MERCHANTAB ON AND D TO ASSUME WITH FOR DEALERS OR ARE DETERRENTS GUARANTEE OR HE MAX FOR LIAB TY WHATSO COSTS FOR MAI ion or remova MUM OT LIMITED FRINGEME RECTED NE TS PRODUCT Y AND AL STA AUTOMOBILE ITS PART DAMAGE AND O he unit including w the associated sensors and accessories c missing or altered ithout ers e of imitation the siren the remote transmi arry a one year
33. ut See Alarm Features for more details See Advanced Start under Remote Start Features for more details 2010 Directed Electronics All rights reserved 13 Advanced Commands Level 4 Press and release the f button 4 times The transmit LED illuminates in sets of quadruple flashes to indicate Level 4 Full Silent Arm Press and release The alarm arms doors lock and the siren chirps and parking lights flash 4 times Defogger i Press and release Activates the vehicle Defogger circuit if connected while Remote Start is activated and the parking lights flash 3 times For convenience the Defogger circuit will also automatically activate 10 seconds after emote starting if the temperature is below 55 F Note Remote Start must be active to use this feature AUX 4 Press and release AUX Activates or if On deactivates the Aux 4 output See Alarm Features for more details This feature must be installed and turned on by an authorized Directed dealer 14 2010 Directed Electronics All rights reserved Remote Programming The remote controls have operations that can be configured to a user s personal preferences The following instruction will direct you through the available programming options for both remote controls Enter programming press and hold the f button for 8 seconds the transmit LED turns on to indicate the Main Menu is accessed Exit programming or go
Download Pdf Manuals
Related Search