Atlas Quiet Mini Server Case User`s Manual
Contents
1. Antec The Bower of Bou Atlas ouiet Mini Server Case User s Manual Manuel de l utilisateur Anwenderhandbuch Manuale per l operatore Manual del usuario BREN AAS At Antec we continually refine and improve our products to ensure the highest quality So it s possible that your new case may differ slightly from the descrip tions in this manual This isn t a problem it s simply an improvement As of the date of publication all features descriptions and illustrations in this manual are correct Disclaimer This manual is intended only as a guide for Antec s Computer Enclosures For more comprehensive instructions on installing the motherboard and peripherals please refer to the user s manuals which come with the components and drives Atlas User s Manual Atlas Quiet Mini Server Case This case comes with a 550 Watt EPS12V power supply Turn the switch to the ON 1 position before you boot up the computer for the first time Normally you won t need to switch to the OFF O position since the power supply includes a soft on off feature which lets you turn the computer on and off by using the soft switch on the computer case If the computer crashes and you can t shut it down using the soft switch you can switch the main power to the OFF O position to clear the fault then reboot Only for models designed for sale in the European Union Antec power supply models feature Power Factor Correction PF2. C circuitry in accordance with European standard regulation code EN61000 3 2 By altering the input current wave shape PFC improves the power factor of the power supply This results in increased energy efficiency reduced heat loss prolonged life for power distribution and consumption equipment and improved output voltage sta bility Together with the high efficiency design and the quiet 80mm fan the power supply delivers a cleaner and quieter operating environment Setting Up 1 Place the case upright on a flat stable surface 2 Note not applicable to models designed for the European Union Before instal lation check the red voltage switch setting on the power supply It should match your local voltage 115V for North America Japan etc and 230V for Europe and many other countries If it doesn t match please change the set ting If you don t you could damage your equipment and void your warranty 3 Loosen the thumbscrews from the right side panel Remove it by swinging it out Note Don t use your fingernails to pry or lift the panels 4 Inside the case you should see the power supply some wiring with marked connectors USB PWR etc and installed I O panel a power cord and a plastic bag containing more hardware screws brass standoffs plastic stands etc and six drive rails 5 There are three plastic tabs on the left side of the bezel They fasten the front bezel to the metal chassis Release the tabs from the
3. d Input Static Acoustical Input Current Pressure Noise Power High 0 24A 2 24 m min 2 54 mm H20 30 dBA 2 9 W 2000 RPM Max 79 CFM 0 10 inch H20 Medium 0 2A 1 59 m min 1 53 mm H20 28 dBA 2 4 W 1600 RPM 56 CFM 0 06 inch H20 Low 0 13A 1 1 m min 0 92 mm H20 25 dBA 1 6 W 1200 RPM 39 CFM 0 04 inch H20 The Front 92mm fans You can install two 92mm fans to the fan cage in front of the internal 3 5 drives These fans must be installed so that the air is blowing into the case We recommend using Antec 92mm TriCool fans to balance quiet performance with maximum cooling See our web site for product information Note Please choose your fan speed wisely In most cases a medium or even low speed setting will be enough to supply adequate cooling Antec Inc 47900 Fremont Blvd Fremont CA 94538 US tel 510 770 1200 fax 510 770 1288 Antec Europe B V Sydneystraat 33 3047 BP Rotterdam The Netherlands tel 31 0 10 462 2060 fax 31 0 10 437 1752 Customer Support US amp Canada 1 800 22ANTEC customersupport antec com Europe 31 0 10 462 2060 europe techsupport antec com www antec com Copyright 2006Antec Inc All rights reserved All trademarks are the property of their respective owners Reproduction in whole or in part without written permission is prohibited Printed in China Version 1 0 1 01 26 2006
4. gnment for Front Panel IEEE 1394 Connector Fin Signal Names Pin Signal Names s_ tre 6 ret 7 a 1av Fused 8 12 rosea Ps key Worn 10 Ground ooog OO0O00O0 WN O Connecting the Audio Ports There is an Intel standard 10 pin connector that has 7 individual wires with con nectors leading to the front panel speaker and microphone connection If the motherboard supports Intel s standard onboard audio connector you can plug the 10 pin connector directly onto the board For non Intel standard audio connection you will need to plug the 7 individual connectors to the motherboard See the fol lowing instructions Locate the internal audio connectors from the motherboard or sound card Consult the motherboard or sound card manual for the pin out positions Microphone Signal Pin Connect the MIC connector to this pin Microphone Power Connect the MIC BIAS connector to this pin Ground Pin Connect the AUD GND connector to this pin Front Right Speaker Out Pin Connect the FROUT R connector to this pin Front Left Speaker Out Pin Connect the FPOUT L connector to this pin Rear Right Speaker Out Pin Connect the RET R connector to this pin Rear Left Speaker Out Pin Connect RET L connector to this pin Oe ONS Hard Disk Installation There is a hard disk cage right under the external 5 25 drive You can mount four hard drives using the trays inside it 1 Open the front bezel as described in Se
5. nd make sure it matches the attached table If it does not match this Intel standard please call Antec customer service at 800 22ANTEC North America or 31 0 10462 2060 Europe to buy a USB adapter This adapter will allow you to connect the front USB to the motherboard on a pin by pin basis Motherboard Pin Layout Pin Signal Names Pin Signal Names USB Power 1 USB Power 2 Negative Signal 1 4 Negative Signal 2 Positive Signal 1 6 Positive Signal 2 7 eons 8 ona 9 Key No Connection Empty Pin OOOUF O0O00O0 W jo Connecting the IEEE 1394 FireWire i Link Port You will find a single 10 pin connector on a cable attached to the front IEEE 1394 connection This is an Intel standard connector which is keyed so that it can t be accidentally reversed when connected to a proper Intel standard motherboard header Connect the 10 pin connector to the motherboard header so that the blocked pin fits over the missing header pin Note Please check the motherboard manual for your IEEE 1394 header pin layout and make sure it matches the attached table If you intend to connect the front FireWire port to an IEEE 1394 add on card that comes with an external type IEEE 1394 connector please call Antec customer service at 800 22ANTEC North America or 31 0 10 462 2060 Europe to buy an adapter This adapter will allow you to connect the front IEEE 1394 port to the external type connector Pin Assi
6. nector for the motherboard It also includes four SATA connectors five to seven 4 pin peripheral power connectors one to two 4 pin Floppy Drive power connectors and one PCI Express graphic card power connector Picture 1 Picture 2 1 Connect the 24 pin Main Power Connector and the 4 pin 12V or 8 pin 12V connector to your moth Y erboard as needed If your motherboard uses a 20 pin connector detach the 4 pin attachment on the 24 pin For 24 pin For 20 pin motherboards motherboards power connector see pictures 1 and 2 Connect the peripheral power connectors to devices such as hard drives optical drives etc 2 Connect the Reset switch labeled RESET SW to the motherboard at the RST connector Make sure the label always faces the front of the case 3 Power LED labeled POWER LED connector is located behind the Reset connector 4 Power Switch labeled POWER SW connects to the PWR connector on the motherboard 5 Hard Drive LED labeled H D D LED connects to the IDE connector Connecting the USB Ports You will find a single 10 pin connector on a cable attached to the front USB ports This is an Intel standard connector which is keyed so that it can t be accidentally reversed when connected to a proper Intel standard motherboard header Connect the 10 pin connector to the motherboard headers so that the blocked pin fits over the missing header pin 2 Note Please check the motherboard manual for the USB header pin layout a
7. supply to the male 4 pin con nector on each of the devices RON To install a floppy or other external 3 5 device to the 5 25 to 3 5 Adapter 1 Slide the Adapter out 2 Place the drive to the adapter and fasten the drive with screws provided 3 Find a 4 pin floppy power connector on the power supply and connect it to the male 4 pin connector on the devices Cooling System The TriCool fan The case includes one 120mm TriCool fan installed in the rear This fan has a three speed switch that lets you choose between quiet performance or maximum cooling See specifications below The fan is installed so that the air is blowing out of the case Connect a large 4 pin connector from the power supply to the male 4 pin connector on the fan Note The minimum voltage to start the fan is 5V We recommend that our users set the fan speed to High if you choose to connect the fan to a fan control device or to the Fan Only connector found on some of Antec s power supplies A fan control device regulates the fan speed by varying the voltage to it The voltage may start as low as 4 5V to 5V Connecting a TriCool set on Medium or Low to a fan control device may result in the fan not being able to start The already lowered voltage from the fan control device will be further reduced by the TriCool circuitry below 5V Specifications Size 120mm x 120mm x 25 4mm Rated Voltage DC 12V Operating Voltage 10 2V 13 8V Spee
8. top down to release the bezel 6 Swing the bezel open to about 45 and gently lift the bezel up The front bezel will come off easily Set the bezel aside in a safe place Installing the Motherboard This manual does not cover CPU RAM or expansion card installation Please consult the motherboard manual for specific mounting instructions and troubleshooting 1 Lay the case down with the open side facing up The drive cages and power supply should be visible 2 Make sure you have the correct I O panel for the motherboard If the panel provided with the case isn t suitable please contact the motherboard manufac turer for the correct I O panel 3 Line up the motherboard with the standoff holes and remember which holes are lined up Not all motherboards will match with all the provided holes this is normal and won t affect functionality 4 Remove the motherboard 5 Screw the brass standoffs into the threaded holes that line up with the mother board Do not overtighten the standoffs Some standoffs may be pre installed for your convenience 6 Place the motherboard on the brass standoffs 7 Screw in the motherboard to the standoffs with the provided Philips head screws The motherboard is now installed Connecting the Power and LED This case has an Antec TruePower 2 0 TP2 550EPS12V power supply which is EPS12V compatible and comes with a configurable 24 pin Main Power Connector an 8 pin 12V and a 4 pin 12V Power Con
9. tting Up section 2 Loosen the two thumbscrews Swing open the fan cage and gently lift the cage upward to remove it You will see four drive trays with soft silicon grom mets inside the cage 3 Squeeze the metal clips on each side of the tray and slide the tray out 4 Mount your hard drive into the drive tray through the bottom rubber grommets with the special screws provided Note Don t over tighten the screws Over tightening the screws will reduce the vibration and noise dampening abil ity of the rubber grommets 5 Slide and lock the tray back into the case 6 Find a 4 pin molex connector on the power supply and connect it to the male 4 pin connector on the device 7 Repeat the same procedure for the other devices as necessary 8 Put the front fan cage back to the case If you plan to mount the optional 92mm case fans do it now See The Cooling section for fan installation 5 25 Device Installation There are four external 5 25 drive bays one with 5 25 to 3 5 Adapter Carefully remove the metal plate covering the drive bay 1 Take two plastic drive rails and mount them to the sides of the 5 25 device Make sure to use the front set of the screw holes on the drive rail Also make sure the end of the drive rail is angled away from the device and facing forward Slide the device into the drive bay until you hear a click Mount the other devices accordingly Connect a large 4 pin connector from the power
Download Pdf Manuals
Related Search