Home

LCD Panel FHD551-W User Manual

image

Contents

1. Two people are required to safely lift and install the LCD panel Do not push or shake the LCD panel This may cause damage or injury Do not apply pressure to the front of the LCD panel This may cause damage or injury e If smoke or an unidentified odor comes from the LCD panel remove the power plug from the outlet immediately and contact your dealer immediately Do not try to repair the product yourself e Do not block LCD panel ventilation openings e During installation provide a minimum of 2 in 5 cm spacing from the wall and 2 in 10 cm spacing from the ceiling and sides to allow proper ventilation Power Safety e DO NOT attempt operation if the AC supply and cord are not within the specified voltage and power range Disconnect power from the LCD panel before moving it or opening any enclosure Position all cables where they cannot contact hot surfaces be pulled or tripped over e Do not overload power outlets and extension cords Do not operate if the LCD panel power cord or power outlet appear damaged LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Introduction The LCD Panel FHD551 W provides high definition resolution at 1920 x 1080 with a weather resistant design to allow for outdoor installation This user manual provides data about the LCD panel installation instructions operation care and troubleshooting tips Features e High brightness 700 nits typ e
2. Adjust the PIP Mode Picture in picture PIP mode adjusts the size of the PIP image that displays within the main image 1 2 3 4 5 Press vw to select the required PIP mode Press MENU on the remote control Press to navigate to the Display Settings menu Press and then to select PIP Mode Press A Side by Side C Medium PIP Large PIP D Small PIP 0000 Press ENTER to save changes Press EXIT to exit the OSD menu Adjust PIP Position Picture in picture PIP position adjusts the location of the smaller image within the main image There are two methods for adjusting the PIP position Method 1 Press P POSITION on the remote control until the image moves to the desired location Method 2 Ui A U N PR Press MENU on the remote control Press to navigate to the Display Settings menu Press and then to select PIP Position Press gt Press until the image moves to the desired location A Top Right C Bottom Right Top Left Bottom Left B D 0000 Press ENTER to save changes Press EXIT to exit the OSD menu LCD Panel FHD551 W User Manual 17 020 100996 01 Rev 2 12 2012 Operation CHAISTIE Swap between the Main Image and the PIP Image Press SWAP on the remote control Swap between the Main Audio and the PIP Audio Press AUDIO on the remote control Turn IRFM On or Off Use image retention frame motion IRFM mode to help avoid image retenti
3. rce iuc Ak waere a RE 16 Adjust the PIP Mode zu 2 sob ae ee Rok Ra RR RU AA a ee a 17 Adjust PIP Position iux hd Ea ee A een en 17 Swap between the Main Image and the PIP Image s 18 Swap between the Main Audio and the PIP Audio lens 18 020 100996 01 Rev 2 12 2012 Care and Cleaning Clean the LCD Panel Screen RS 232C Commands RS 232C Command Format RS 232C CMD Options Compliant Timing Troubleshooting Specifications LED Panel ee ected Weis he an Performance mm Turn IRFM On or Off o o oo ooo oo Adjust Volume llle oo RS 232C Control 00000 Adjust Wake Up From Sleep OSD MENU a aha id cel ate da Seater at BS OSD Menu Controls Image Settings Image Settings continued Display Settings 4 Audio Settings ooo Basic Settings Basic Settings continued Advanced Settings System Status o ooo ooo Clean the LCD Panel Cabinet Clean the Power Cord o o Clean the Dust Filter Environment o oooooooo occ Physical erica ee PARES anta a a a a UD a aet CHAISTIE LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Important Safety Information Read this information thoroughly and completely before insta
4. OSD Timeout Adjusts the menu timeout The timeout ranges from 5 120 seconds The setting defaults to 30 Sleep Timer Configures the time after which the LCD panel switches to standby mode Options include Off 15 30 60 90 and 120 minutes The default is OFF Power LED Configures the LED power setting Options include Off DCR and light sensor The default is off Real Time Clock Expands the Basic Settings menu See Basic Settings continued on page 25 24 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Operation Basic Settings continued Current Time Basic Settings Current Time Timer Mode Veek Enable Power On Power Off MON E 00 00 0 0 0O TUE 00 00 00 00 VVED 10 0 00 THU 00 00 00 00 FRI 00 00 00 00 SAT 00 00 00 00 SUN 00 00 00 00 Configures the current time settings The time and date are displayed in this format Year Month Day Hour Minutes Weekday The time format is 24 hour Timer mode Configures the power on and power off timer Options include e User manually configure the alarm timer of each day e Same Settings On All configure the same alarm timer for every day e Same Settings On Work Days configure the same alarm timer for Monday to Friday LCD Panel FHD551 W User Manual 25 020 100996 01 Rev 2 12 2012 Operation CHAISTIE Advanced Settings Do not disconnect the AC power cord when Winter Mode is
5. Turn LCD panel power on 07 01 02 50 4F 57 01 08 07 01 00 50 4F 57 01 08 Request LCD panel power status 07 01 01 50 4F 57 08 07 01 00 50 4F 57 XX 08 XX 0 when off or 1 when on Set the LCD panel contrast to 30 07 02 02 43 4F 4E 1E 08 07 02 00 43 4F 4E 1E 08 Request the LCD panel to use large 07 19 02 50 53 43 03 08 07 19 00 50 53 43 03 08 PIP Reset the LCD panel display settings 07 02 02 41 4C 4C 00 08 07 02 00 41 4C 4C 00 08 Request LCD panel serial number 07 01 01 53 45 52 08 07 01 00 53 45 52 S 0 S 12 08 S 0 S 12 the serial number in ASCII Request LCD panel firmware version 07 01 01 47 56 45 08 07 01 00 47 56 45 S 0 S 5 08 S 0 S 5 the firmware version in ASCII LCD Panel FHD551 W User Manual 31 020 100996 01 Rev 2 12 2012 RS 232C Commands RS 232C CMD Options Main Control CMD Type Item Item Power Power POW Control and Control Input Source Input MIN Source Input MIN Source Display Display BRI Adjustment Adjustment BRL BLC CON HUE SAT COT COT 32 W R W R W R W R W R W R W R W R W R W R W R Value Reply DEC DEC 00 01 00 01 02 03 04 09 10 13 0 100 0 100 00 01 0 100 0 100 0 100 00 01 02 00 01 00 01 02 03 04 09 10 13 Current value Current value 00 01 Current value Current value Current value 00 01 02 Content O
6. 85 RH max LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Specifications Physical Specification Value Dimension W x H x D 51 2 in x 30 4 in x 4 8 in 130 cm x 77 1 cm x 12 2 cm Net Weight 121 Ib 55 Kg Gross Weight 132 Ib 60 Kg Mounting screw size M8 x 15 mm PA gt 4 8 in 12 2 cm 54 8 in 139 2 cm 30 4 in 77 1 cm 47 8 in 121 3 cm gt Y 51 2 in 130 cm 11 2 in 28 5 cm 7 9 in 20 cm LCD Panel FHD551 W User Manual 45 020 100996 01 Rev 2 12 2012 Specifications Parts Part Number 142 001102 XX 142 100102 XX 108 383105 XX 108 390103 XX 108 388100 XX 108 376107 XX 108 375106 XX 108 392105 XX 46 Description LCD Panel FHD551 W Flat Panel FP Remote Control Power Cord NA Power Cord EU Power Cord UK Power Cord JP Power Cord CN Power Cord AU CHAISTIE LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 O00 103397 01 ASSY TECH DOCS FHD551 W Corporate offices USA Cypress ph 714 236 8610 Canada Kitchener ph 519 744 8005 Worldwide offices United Kingdom ph 44 118 977 8000 France ph 433 0 1 41 21 00 36 Germany ph 49 2161 664540 Eastern Europe ph 36 0 1 47 48 100 Middle East ph 4971 0 4 299 7575 Spain ph 34 91 633 9990 Singapore ph 65 6877 8737 Beijing ph 86 106561 0240
7. Shanghai ph 86 21 6278 7708 For the most current technical documentation please visit www christiedigital com Japan ph 81 3 3599 7481 South Korea ph 82 2 702 1601 CHRISTIE
8. Zoom In 5A 4F 4D Zoom Out 115200 42 52 41 38400 19200 9600 MENU Key 52 43 55 INFO Key LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHRISTIE Main Control CMD Type Item Item Other Other RCU Ww Control Control cont cont cont cont LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 Value Reply DEC DEC 02 02 03 03 04 04 05 05 06 06 07 07 08 08 09 09 10 10 11 11 12 12 13 13 14 14 15 15 18 18 19 19 20 20 21 21 22 22 23 23 24 24 25 25 26 26 RS 232C Commands CMD HEX 52 43 55 cont Content Remark UP Key DOWN Key LEFT Key RIGHT Key ENTER Key EXIT Key VGA Key DVI Key HDMI1 Key HDMI2 Key DISPLAYPORT Key COMP Key S V Key AV Key SOURCE Key P SOURCE Key PIP Key P POSITION Key SWAP Key SCALING Key FREEZE Key MUTE Key BRIGHT Key 35 RS 232C Commands Main Control Item Item Other Other Control Control cont cont Audio Scheme Selection 36 CMD RCU cont ALL KLC SER MNA GVE RTV RTT RSF WFS VOL MUT SCM Type Value Reply DEC DEC Ww cont W R W R W R W R W R 27 28 29 30 00 00 01 0 255 0 255 00 01 02 0 100 00 01 00 27 28 29 30 00 00 01 13 bytes 13 bytes 6 bytes Current value Current value 00 01 00 01 02 Current
9. analog input This is the default setting e VGA Digital RS232 the LCD panel wakes up when it receives an active signal from the VGA HDMI DisplayPort DVI inputs or an RS 232C command e Never Sleep the LCD panel never goes to sleep 5 Press ENTER to save changes 6 Press MENU to return to the previous menu or EXIT to exit the OSD menu LCD Panel FHD551 W User Manual 19 020 100996 01 Rev 2 12 2012 Operation CHAISTIE OSD Menu The OSD menu automatically determines whether a graphics source or video source is Q provided Some menu options such as saturation or hue are not available when a graphics source is provided because changing these options would degrade the picture quality The onscreen display OSD menu provides adjustment settings for the LCD screen OSD Menu Controls Use the remote control to access the onscreen display OSD menu Press MENU Press or to scroll up and down the menu Press or to adjust a selected setting Press ENTER to save changes Wn ue JO N nS Press MENU to return to the previous menu or EXIT to exit the OSD menu Image Settings Use the Image Settings menu to make common image adjustments such as contrast and sharpness See OSD Menu Controls on page 20 for OSD menu control information Image Settings Scheme Brightness Contrast Sharpness Saturation Hue Backlight Color Temperature amp Gamma Scheme Adjusts the image scheme Opt
10. in either direction b Problems or damage caused by combination of a Product with non Christie equipment such as distribution systems cameras video tape recorders etc or use of a Product with any non Christie interface device c Problems or damage caused by misuse improper power source accident fire flood lightening earthquake or other natural disaster d Problems or damage caused by improper installation alignment or by equipment modification if by other than Christie service personnel or a Christie authorized repair service provider e Failure due to normal wear and tear f Image retention on LCD flat panels g Direct exposure to sunlight PREVENTATIVE MAINTENANCE Preventative maintenance is an important part of the continued and proper operation of your product Please see the Maintenance section for specific maintenance items as they relate to your product Failure to perform maintenance as required and in accordance with the maintenance schedule specified by Christie will void the warranty Addendum The CD included with this printed manual contains an electronic copy in English Please read all instructions before using or servicing this product ee ih A POCA HL AS BE REA mA ts HF A Ee bed Pt N Ra o Le DC fourni avec ce manuel imprim contient une copie lectronique en francais S il vous plait lire toutes les instructions avant d utiliser ou de r parer ce produit Das CD da
11. require more frequent cleaning 1 Remove 2 screws from the right side of the back of the LCD panel 2 Remove the dust filter cover 3 Remove the dust filter 4 Clean the dust filter by rinsing it below running tap water Do not scrub the filter or use harsh cleaners 5 Place the clean dust filter back into the LCD panel The dust filter can be wet when it is replaced 6 Replace the filter cover and 2 screws 30 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE RS 232C Commands This section describes how to control the power and OSD menus using recommended standard 232C RS 232C Command Format Recommended standard 232C commands use the following format STX IDT TYPE CMD VALUE Or REPLY ETX Variable No of Bytes Description STX 1 Starting byte Value equals 07 IDT 1 00 Hex Num for broadcast mode no announcing only for Video Wall 01 19 Hex Num for single control mode TYPE 1 Specifies the type of command e 00 return to host from LCD panel 01 read action 02 write CMD 3 Specifies the command See RS 232C CMD Options on page 32 VALUE 1 Specifies the command s parameter setting REPLY 1 Provides the response returned by the LCD panel ETX 1 Ending byte Value equals 08 For example Description Command Sent Command Received Computer to LCD Panel LCD Panel to Computer Turn LCD panel power off 07 01 02 50 4F 57 00 08 07 01 00 50 4F 57 00 08
12. 157 5 101 121 75 88 75 106 5 119 146 25 162 138 5 154 13 5 13 5 27 03 27 74 25 74 176 74 25 74 25 74 176 74 25 74 25 74 25 74 18 74 25 148 5 148 352 148 5 020000000000 o HMI 00 070707070707 0 OOo 0 VGA 000 00 OOO CHAISTIE Component S Video Composite DisplayPort DVI j O OoOo oo0oo0oooooo0oo0ooOO Ui N o OO oO O 1 1 1 1 0007070070 0007070700760 000707 07070070 O OO OOo O O OO LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Troubleshooting This section provides LCD panel troubleshooting information LCD Panel Problem Black dots are visible on the image Flickering image Image color is abnormal The LCD Panel is not functioning correctly Image ghosting is visible Image is dark Image is not centered Image size is not correct No image Partial blurring of the image is visible LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 Correction e Clean the screen surface with a soft cloth See Clean the LCD Panel Screen on page 29 Remove objects that contain a magnetic field for example speakers steel structures or high voltage lines installed near the LCD panel Adjust the graphic interface PC mode within allotted frequency parameters e Adjust the color settings See Image Settings on page 20 Reset the display e If YUV terminals are used verify that the cables are connected correctly C
13. Balance Adjusts the left and right speaker balance The values range from 0 20 The HDMI Audio Input default is 10 Adjusts the HDMI audio input Options include HDMI and PC audio input The default is HMDI DP Audio Input Internal Speakers Adjusts the DisplayPort audio input Options include DisplayPort and PC Audio Input The default is DisplayPort Turns the internal speakers on or off Options include On and Off The default is On LCD Panel FHD551 W User Manual 23 020 100996 01 Rev 2 12 2012 CHRISTIE Operation Basic Settings Use the Basic Settings menu to make OSD menu adjustments See OSD Menu Controls on page 20 for OSD menu control information OSD Transparent Basic Settings OSD Transparent OSD Location OSD Zoom Off OSD Rotation Landscape OSD Language English OSD Timeout Sec Sleep Timer Power LED Real Time Clock Adjusts the menu transparency level Transparency levels ranges from 0 to 100 The default is 0 OSD Location OSD Zoom Adjusts the menu location Options include up down left or right Configures whether the menu zoom is on or off The default is off OSD Rotation Adjusts menu rotation Options include landscape or portrait The default is landscape OSD Language Adjusts the menu language Options include Simplified Chinese French German Italian Portuguese Russian Spanish Japanese and Korean The default is English
14. Version FHD551 VV V0 10 SUB MCU V01 LCD Panel FHD551 W User Manual 27 020 100996 01 Rev 2 12 2012 CHRISTIE Care and Cleaning Electrical shock hazard Always turn the power off and disconnect all power sources from the A DANGER LCD panel before servicing This section provides care and cleaning instructions for the LCD panel FHD551 W Clean the LCD Panel Screen e Do not use abrasive cleaners on the LCD panel NOTICE Do not scratch or hit the LCD panel with hard objects such as fingernails or jewelry To remove accumulated dust lightly wipe the surface of the LCD panel with a soft clean cloth To remove dirt gently wipe the surface with a soft clean cloth that is dampened with water or a non ammonia based glass cleaner To remove water spots gently wipe the surface with a soft clean cloth that is dampened with a 3 1 water and household vinegar solution Clean the LCD Panel Cabinet Wipe the LCD panel cabinet using a soft cloth that is dampened with a mild liquid dish soap Clean the Power Cord Power cord dust build up can lead to fire or electrical shock At regular intervals remove the power plug from the outlet and clean off the dust LCD Panel FHD551 W User Manual 29 020 100996 01 Rev 2 12 2012 Care and Cleaning CHAISTIE Clean the Dust Filter Do not use harsh cleaners to clean the dust filter Clean the dust filter once a year to prevent dust build up In high dust environments the filter may
15. changes to specifications at any time without notice Performance specifications are typical but may vary depending on conditions beyond Christie s control such as maintenance of the product in proper working conditions Performance specifications are based on information available at the time of printing Christie makes no warranty of any kind with regard to this material including but not limited to implied warranties of fitness for a particular purpose Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material The product is designed and manufactured with high quality materials and components that can be recycled and reused This symbol E means that electrical and electronic equipment at their end of life should be disposed of separately from regular waste Please dispose of the product appropriately and according to local regulations In the European Union there are separate collection systems for used electrical and electronic products Please help us to conserve the environment we live in Canadian manufacturing facility is ISO 9001 and 14001 certified GENERAL WARRANTY STATEMENTS For complete information about Christie s limited warranty please contact your Christie dealer In addition to the other limitations that may be specified in Christie s limited warranty the warranty does not cover a Problems or damage occurring during shipment
16. set to Enable NOTICE Use the Advanced Settings menu to configure advanced features such as VGA mode See OSD Menu Controls on page 20 for OSD menu control information Advanced Settings Auto Adjustment Image Position Phase Clocks VGA ADC Settings gt Flesh Tone Off IRFM Off Baud Rate 115200 Smart Light Control Off VVake Up From Sleep VGA Only Temperature amp Fan Status gt Winter Mode Disable Factory Reset No Auto Adjustment Forces the LCD panel to reacquire and lock to the input signal This is useful when the signal quality is poor This feature does not continually reacquire the signal Options include Yes and No The default is No Image Position Adjusts the VGA mode image position Options include Up Down Left and Right Phase Adjusts the VGA mode phase Phase ranges from 0 63 Clocks Adjusts the VGA mode clocks The clocks range from 0 100 VGA ADC Settings Sets the VGA ADC setting Options include Default and User The default is Default Flesh Tone Adjusts the video mode flesh tone settings Options include Off Low Medium and High The default is Off IRFM Creates slight frame motion to help avoid image retention Options include On and Off The default is Off Baud Rate Adjusts the number of signaling events per second Options include 115200 38400 19200 9600 The default is 115200 Smart Light Adjusts the screen brightness Options include Off DCR dynamic
17. source A VGA E DisplayPort B HDMI1 F Composite Video C HDMI2 G S Video D DVI H Component OOO 6 Press ENTER to save changes 7 Press EXIT to exit the OSD menu LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 15 Operation CHAISTIE PIP Picture in picture PIP allows a second smaller image to play within the main image PIP Sources Available picture in picture PIP source images are dependent on the source of the main image For example if your main screen is using a VGA source you cannot use a VGA PIP source PIP Main Screen Source Source VGA HDMI1 HDMI2 DVI DisplayPort Video S Video Component VGA Y Y Y Y Y Y 4 HDMI 1 v v Y v Y HDMI 2 Y Y Y Y Y DVI Y v Y v Y DisplayPort Y Y Y v Y Y v Video Y Y Y Y Y a E Y S Video Y Y Y Y Y a Y Component Y Y Y v Y v Y Turn PIP On or Off Press PIP on the remote control Adjust the PIP Source 1 Select the source for the main image Press the required source button on the remote control VGA DVI HDMI 1 COMP AV HDMI 2 DISPLAYPORT or S V See Select the Input Source on page 15 for source types 2 Press PIP 3 Select the source for the PIP image a Press P SOURCE b Press or v to select the PIP source c Press ENTER See PIP Sources on page 16 for information about main image and PIP image source compatibility 16 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Operation
18. with wet hands Do not disconnect the AC power cord when Winter Mode is set to Enable NOTICE 14 2 a Na UE er De See Advanced Settings on page 26 If the LCD panel is on press Power OFF on the remote control Unplug the power cable Remove 4 screws M6x30mm from the exterior I O cover Remove the external I O cover Remove the internal I O cover Press the power switch to the O position Unplug the power cable and remove the cable from the interior I O cover Hold the interior I O cover against the LCD panel Place the exterior I O cover over the interior I O cover and secure in position using 4 screws LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Operation e Do not send a static non moving image to this LCD panel for long periods of time NOTICE because it may cause image burn in or image retention e Turn the power off for 6 consecutive hours after 18 hours of usage to avoid image retention This section provides procedures and information for operating the LCD panel Turn Power On 1 Verify that power is connected to the LCD Panel See Open the Connections Panel on page 12 2 Press Power ON on the remote control Turn Power Off Press Power OFF on the remote control Select the Input Source 1 Press MENU on the remote control 2 Press to navigate to the Display Settings menu 3 Press and then to select Select Source 4 Press 5 Press to select an input
19. 5 31 5 43 269 85 008 36 SVGA 800 x 600 35 156 56 25 36 37 879 60 317 40 48 077 72 188 50 46 875 75 49 5 53 674 85 06 56 25 XGA 1024 x 768 48 363 60 004 65 56 476 70 069 75 g 60 023 75 029 78 75 i 68 677 84 997 94 5 WXGA1360 x 768 47 712 60 015 85 5 1280 x 720 44 444 59 98 64 44 772 59 86 74 5 56 456 74 78 95 75 1280 x 768 47 776 59 87 79 5 47 396 59 995 68 25 68 633 84 837 117 5 1280 x 800 49 306 59 91 71 49 702 59 81 83 SXGA 1152 x 864 67 5 75 108 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 HDMI 0000707000007 00007 0000707070700 ooooooooocoooocooooooosoo o YGA Component S Video Composite DVI 0000000 000000 000 00 0 00 OOO O O DisplayPort 00 00 00 0000 0 00 0 0007 000070707000 39 Compliant Timing VESA cont EDTV SDTV HDTV 40 Timing SXGA 1280 x 1024 SXGA 1400 x 1050 1440 x 900 WSXGA 1680 x 1050 UXGA 1600 x 1200 1920 x 1080 WUXA 1920 x 1200 NTSC PAL 480p 576p 720p 1280 x 720 1080i 1920 x 1080 1080p 1920 x 1080 fH kHz 63 981 79 976 91 146 64 744 64 317 55 469 55 935 64 674 65 29 75 66 587 74 038 15 734 15 625 31 5 31 25 37 5 44 995 45 28 13 33 716 33 75 27 28 125 33 716 33 75 56 25 67 433 67 5 fV Hz 60 02 75 025 85 024 59 95 59 98 59 901 59 88 59 883 59 954 60 59 93 59 95 29 97 25 60 50 50 59 94 60 50 59 94 60 24 25 29 30 50 59 94 60 Dot Clock MHz 108 135
20. 8 383 Green Gain 128 383 Blue Gain 128 383 Red Offset 50 50 Green Offset 50 50 Blue Offset 50 50 Phase Clock Horizontal Position Vertical Position Auto Adjust Sharpness PIP OFF PIP Small PIP Medium PIP Large PIP Side by Side VGA RS 232C Commands CMD HEX 43 4F 54 cont 47 41 43 55 53 52 55 53 47 55 53 42 55 4F 52 55 4F 47 55 4F 42 50 48 41 43 4C 4F 48 4F 52 56 45 52 41 44 4A 53 4841 50 53 43 50 49 4E Remark 33 RS 232C Commands Main Control CMD Type Item Item Other PIP source PIN W R Control selection cont cont cont cont PIP PPO W R position 34 PIP Main SWA Ww Swap Scaling ASP W R ZOM WwW Baud Rate BRA W R Adjustment Other RCU WwW Control Value Reply DEC DEC 01 02 03 04 09 10 13 00 01 02 03 00 00 01 02 03 00 01 00 01 02 03 00 01 01 02 03 04 09 10 13 00 01 02 03 00 00 01 02 03 00 01 00 01 02 03 00 01 CHAISTIE Content CMD Remark HEX Digital DVI 50 49 4E cont S Video Composite Video Component HDMI 1 HDMI 2 DisplayPort PIP Position Bottom Left 50 50 4F PIP Position Bottom Right PIP Position Top Left PIP Position Top Right Swap Main and PIP 53 57 41 Native 41 53 50 Full Screen Pillar Box Letter Box
21. Blue Gain first Values range from 128 383 The default is 256 Red Green and Adjusts the color offset The Color Temperature must be set to User to adjust Blue Offset these settings Values range from 50 50 The default is 0 LCD Panel FHD551 W User Manual 21 020 100996 01 Rev 2 12 2012 Operation CHAISTIE Display Settings Use the Display Settings menu to make common source adjustments such as zoom or PIP See OSD Menu Controls on page 20 for OSD menu control information Display Settings Main Aspect Ratio Full Screen Zoom Auto Scan Select Source PIP PIP Mode Side By Side PIP Position Top Left Aspect Ratio Full Screen Side By Side Scale gt Auto Scan Off Select source gt Aspect Ratio Adjusts the picture aspect ratio Options include Full Screen Pillar Box Letter Box and Native The default is Full Screen Zoom Adjusts the picture zoom The zoom ranges from 0 10 The default is O Auto Scan Main Adjusts whether auto scan is on or off When auto scan is on the order is VGA HDMI1 HDMI 2 DVI DisplayPort Composite Video S video then Component The default is On Select Source Adjusts the input source Options include VGA HDMI 1 HDMI 2 S Video Composite Video and Component The default is HDMI 1 PIP Mode Adjusts the picture in picture mode Options include Off Large PIP Medium PIP Small PIP and Side by Side The default is Off PIP Position Adjusts the picture in pict
22. High contrast ratio 4000 1 typ e Full HD 1920 x 1080 resolution e Optically bonded screen e Weatherproof IP56 NEMA 4 rating e Ruggedized design e Portrait or landscape orientation e DACS cooling and filtration system e On Screen Display OSD menu controls e Built in speakers e Image retention frame motion IRFM 1 Brightness and contrast may be slightly reduced due to the protective covering on the glass of the LCD panel LCD Panel FHD551 W User Manual 3 020 100996 01 Rev 2 12 2012 Introduction CHAISTIE What s In The Box Always use the accessories recommended by Christie Digital for compatibility NOTICE Verify that you have all these items before installing the LCD panel e Remote Control e LCD Panel FHD551 W 2 AAA Batteries LCD Panel FHD551 W e Country Specific Power Cord shipped separately u e User Manual e Infrared Extender Cable 4 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Introduction Controls and Indicators This section describes the LCD panel FHD551 W controls and indicators LCD Panel Controls The LCD panel controls are located at the back of the LCD panel Remove the exterior and interior I O panels for access Button Description Power Turns the LCD panel ON 9 and OFF E SOURCE Toggles between sources gt Navigates right or increases a setting value in the OSD menu 4 Navigates left or decreases a set
23. LCD Panel FHD551 W i User Manual 020 100996 01 CHAISTIE LCD Panel FHD551 W USER MANUAL 020 100996 01 NOTICES COPYRIGHT AND TRADEMARKS 2012 Christie Digital Systems USA Inc All rights reserved All brand names and product names are trademarks registered trademarks or trade names of their respective holders REGULATORY The product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment The product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada e IIE MERA F 9 2 ARMAR 971719 9 1 Boy EE a zs 0198 3 spo 7 927 714 99 49913 ABRE AS BA Oz By GENERAL Every effort has been made to ensure accuracy however in some cases changes in the products or availability could occur which may not be reflected in this document Christie reserves the right to make
24. all and 4 in 10 cm spacing from the ceiling and sides when installed e Do not install the LCD panel at a 180 angle screen up or screen down e Install the LCD panel using M8 x 15 mm mounting screws Do not install the LCD panel with screws that are longer than 15 mm or they may damage the LCD panel Before connecting external devices turn the LCD panel and any connected devices OFF After all connections are made turn the LCD panel on before external devices Read the Operation Manuals of the video source equipment before making the connections Install the LCD panel in a shaded location away from direct sunlight for the best viewing experience Prepare the installation site Position the LCD panel in its permanent installation location If rotation is required see Rotate the LCD Panel on page 12 Open the LCD panel connections panel See Open the Connections Panel on page 12 Connect components and power to the LCD panel See Connect Power to the LCD Panel on page 13 See Connect a Video Source to the LCD Panel on page 13 Close the LCD panel connections panel See Close the Connections Panel on page 13 Install the remote control batteries See Connect Power to the LCD Panel on page 13 LCD Panel FHD551 W User Manual 11 020 100996 01 Rev 2 12 2012 Installation CHAISTIE Rotate the LCD Panel Improper ventilation may shorten the operational life of the LCD panel NOTICE Rotate the LCD pan
25. contrast Control Light Sensor The default is Off 26 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Operation Wake Up From Adjusts the wake up from sleep behavior Options include Sleep VGA Only the LCD panel normally wakes up from power saving mode when it receives an active video signal from its VGA analog input VGA Digital RS232 the LCD panel wakes up when it receives an active signal from the VGA HDMI DisplayPort DVI inputs or an RS232 command Never Sleep the LCD panel never goes to sleep The default is VGA Only Temperature amp Fan Provides the status of the thermal sensor and cooling fans Status Winter Mode Adjusts Winter Mode Options include Enable and Disable The default is Disable To maintain a minimum internal temperature the LCD screen may remain partially illuminated when set to Enable Only enable this feature when operating temperatures are below 32 F 0 C as power consumption is greater than 0 5 W Factory Reset Restores all settings to their default value Options include No and Yes The default is No System Status Use the System Status menu to view the status of active sources or the latest firmware version See OSD Menu Controls on page 20 for OSD menu control information System Status Channel Information Source Resolution Main No signal 1024x768 60 0Hz PIP No signal 1024x768 60 0HzZ Total Hours 0 Firmware
26. el in the correct direction for a landscape or portrait orientation Reference the arrow labels on the back of the LCD panel for the proper rotation epow LIYYLYOd U Open the Connections Panel To avoid risk of electric shock do not touch the power cable with wet hands and avoid DANGER handling the power cord during electrical storms 1 Rest the LCD panel on a soft surface with the screen down 2 Remove 4 screws from the exterior input and output I O cover 3 Remove the external I O cover 4 Remove the internal I O cover io 12 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Installation Connect Power to the LCD Panel To avoid risk of electric shock do not touch the power cable with wet hands and avoid handling the power cord during electrical storms 1 Insert the female end of the power cable through the plastic opening of the interior I O cover 2 Plug the female end of the power cable into the AC IN connector See Connection Panel on page 6 3 Press the power switch to the I position Connect a Video Source to the LCD Panel O The infrared extender cable does not work in direct sunlight 1 Insert the video source cable through the plastic opening of the interior I O cover 2 Plug the video source cable into the appropriate connector location See Connection Panel on page 6 Close the Connections Panel To avoid risk of electric shock do not touch the
27. ff soft power On soft power VGA Digital DVI S Video Composite Video Component HDMI 1 HDMI 2 DisplayPort Back Light Brightness Digital Brightness Level Off Back Light On Back Light Contrast Hue Saturation User 6500K 9300K CHAISTIE CMD HEX 50 4F 57 4D 49 4E 4D 49 4E 42 52 49 42 52 4C 42 4C 43 43 4F 4E 48 55 45 53 41 54 43 4F 54 Remark For advanced A D boards Optional LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHRISTIE Main Control Item Item Display Display Adjustment Adjustment cont cont Adjustment Video Mode Other PIP Adjust Control PIP source selection CMD COT cont GAC USR USG USB UOR UOG UOB PHA CLO HOR VER ADJ SHA PSC PIN LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 Type W R cont W R W R W R W R W R W R W R W R W R W R W R W R Value DEC 06 07 00 01 0 255 0 255 0 255 0 100 0 100 0 100 0 63 0 100 00 0 24 00 01 02 03 04 00 Reply DEC 06 07 00 01 Current value Current value Current value Current value Current value Current value Current value Current value Current value Current value 00 Current value 00 01 02 03 04 00 Content 5000K 7500K Off Gamma 2 2 Gamma Red Gain 12
28. heck the LCD panel temperature from the System Status menu If the temperature is below 4 F 20 C move the LCD panel to a warmer location e Verify that the source equipment connection cables are less than 50 ft 15 m in length If additional length is required please contact your authorized dealer for a signal amplifier not provided e Verify that the LCD panel is warmed up It may take several seconds for the LCD panel to warm up after the power is enabled e Adjust the backlight and brightness See Image Settings on page 20 Direct sunlight and hot conditions may cause the screen image to temporarily darken Verify that the input signal is compatible with the display Adjust the format of the image See Display Settings on page 22 e Adjust the image size See Display Settings on page 22 Verify that the power cord is connected properly to the power outlet and to the LCD panel Verify that the main power switch is set to the I position If the power indicator is amber press the power button on the remote control If both the S Video input and the AV2 input are connected remove one Check the operating temperature The LCD panel stops running when it overheats or when the fan s fails Check the environment temperature The LCD panel cannot turn on when the environment temperature is below 4 F 20 C or above 114 F 45 C Remove objects that contain a magnetic field for example speakers steel struc
29. ions include User Vivid Cinema Game and Sport The default is User This option is unavailable when in Graphics mode 20 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Operation Brightness Adjusts the picture brightness Brightness values range from 0 100 The default is 50 Contrast Adjusts the picture contrast Contrast values range from 0 100 The default setting is 50 Sharpness Adjusts the picture sharpness Sharpness values range from 0 24 The default is 12 Saturation Adjusts brilliance and brightness when operating in VIDEO mode Saturation values range from 0 100 The default is 50 This option is unavailable when in Graphics mode Hue Adjusts the green hue when operating in VIDEO mode Hue values range from 0 100 The default is 50 This option is unavailable when in Graphics mode Backlight Adjusts the backlight Backlight values range from 0 100 The default is 80 Color Temperature Expands the Image Settings menu amp Gamma See Image Settings continued on page 21 Image Settings continued Image Settings hy Gamma a Color Temperature A Gamma Adjusts gamma Options include OFF and 2 2 The default is 2 2 Color Temperature Adjusts the color temperature Options include User 5000K 6500K 7500K and 9300K The default is 9300K Red Green and Adjusts the color gain To adjust this setting set the Color Temperature to User
30. lling adjusting or operating the LCD panel FHD551 W General Safety Precautions This product is designed and manufactured to operate within defined design limits Misuse may result in electric shock or fire e Improper installation can result in death or serious injury Make sure that the supports mount and hardware used for the LCD panel installation are adequately designed to hold the required weight and that they are installed correctly e Fire or electrical shock hazard Although the LCD panel meets IP56 weatherproof standards it is not engineered to protect against continuous liquid immersion Do not submerge the LCD panel in any type of liquid Never push any object into an opening at the back of the LCD panel Do not place objects on top of the LCD panel e This is a class A product In a domestic environment this product may cause radio interference for which the user may be required to contain To avoid electric shock or component damage disconnect the LCD panel from AC power before connecting other components to the LCD panel Fire or electrical shock hazard Avoid condensation do not use the LCD panel immediately after moving it from a lower to a higher temperature environment Do not touch the liquid from a broken LCD panel If you have contact with the liquid wash the area with clean water and seek medical attention immediately e Watch for pinch points Do not place your fingers between moving parts
31. n x 0 024 in 0 063 cm x 0 063 cm RGB Vertical Stripe 15 94 KHz Digital 23 92 KHz Analog 23 85 KHz Digital 49 86 Hz Analog VESA Standard 15 7 in x 7 9 in 40 cm x 20 cm Value Clock Phase H Position and V Position VGA SVGA XGA WXGA and HDTV Full Screen Display VESA DPMS DVI DMPM Energy Star 5000K 6500K 7500K 9300K User English Simplified Chinese French German Italian Portuguese Russian Spanish Japanese and Korean 43 Specifications CHAISTIE Power To restrict power consumption to lt 0 5 W during standby mode Wake Up From Sleep Q must be set to VGA Only See Adjust Wake Up From Sleep on page 19 Specification Value Power Input Normal Operation Power Off Winter Mode Disabled Power Off Winter Mode Enabled Speaker Connections Specification Input Connections Output Connections Environment Storage Temperature Operating Temperature Humidity 44 100 240VAC 4A 50 60 Hz 265 W lt 0 5W gt 0 5 W 40 10Wx2 e RS 232C D Sub 9 pin Component RCA e Component Audio RCA L R e S Video Composite Video RCA e Audio In RCA S Video Component Video e Infrared Extender 3 5 mini jack e PC Audio In 3 5 mini jack VGA D sub 15 pin e DVI D HDCP compliant e HDMI 2 e HDMI 1 DisplayPort e AC In Audio out 3 5 mini jack Specification Min 22 F 30 C Max 140 F 60 C Min 4 F 20 C Max 114 F 45 C
32. on from static images This mode is recommended when static images are used for a long time 1 Press MENU on the remote control 2 Press v to navigate to the Advanced Settings menu 3 Press and then to select IRFM Press to set IRFM to On or Off Press ENTER to save changes 9 wv x Press EXIT to exit the OSD menu Adjust Volume Press VOLUME or VOLUMEH to increase or decrease the volume Press MUTE to temporarily turn off all sound To restore the sound when muted press MUTE again RS 232C Control The LCD panel power and OSD menu can be controlled through recommended standard 232C See RS 232C Command Format on page 31 and RS 232C CMD Options on page 32 18 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Operation Adjust Wake Up From Sleep When Wake Up From Sleep is set to VGA Digital RS232 LCD panel power Q consumption is gt 0 5 W when the LCD panel is in power saving sleep mode When set to VGA Digital RS232 Wake Up From Sleep sets the LCD panel to wake up when a digital signal HDMI DVI DisplayPort or RS 232C is sent to the LCD panel 1 Press MENU on the remote control The Image Settings menu displays 2 Press to navigate to the Advanced Settings menu 3 Press and then to select Wake Up From Sleep 4 Press to adjust Wake Up From Sleep e VGA Only the LCD panel wakes up from power saving mode when it receives an active video signal from its VGA
33. oocooocc 1 General Safety Precautions 2 0 nn 1 Power Safety iiid bo edad Dee aa hee EEE Ae Dee ee oe 1 Miroduc An rn a r A 3 Features a PP 3 What s In The BOX coke SR ORE E Rok a Ee RR aes 4 Controls and Indicators 1 oo 5 ECD Panel Controls ais a rc oe a ee a ee ee RC X NUR ORC UACR 5 Indicator Lights 1 xk Ree na eR E RR ow ee ne 5 Connection Panel omiso Ede e a dae d REED EO diode de RC e 6 Remote Control kk ecl Rog x OR RUE e bebe eae Bae rauhen 7 INStANAUON 6465 05 un a PSECU Ae A 9 Package Handling 22222282 RR de m Rx eee ara 9 Unpack the LCD Panel siemens a ele oh o uh o n Pe REO ea ae ews 10 LCD Panel Setup zs o RES ed at a oo XU e ee a s OR ee 11 Rotate the LCD Panel z canada Shee bee awe Deke ee E wok xe OR ROAD ea ah 12 Open the Connections Panel 0 2 nnana d deadar 12 Connect Power to the LCD Panel nn nenn 13 Connect a Video Source to the LCD Panel 2 aa 13 Close the Connections Panel ooo 13 Install the Remote Control Batteries o e e e e 14 Disconnect Power from the LCD Panel o ooo ooo ee 14 Operati serra iria A 15 Turn Power On ii a e a EHEN 15 Turn Power Off eee eed aa sa AA A A A A 15 Select the Input Source su uer Rx a AAA 15 PIP nu EG ae kd we he Ban EN RS IRAN RE CL we Ee 16 PIP SOUFCES cu 4 4 da btw deb Bea ech rm 16 Tuni PIP ONO Off eue ne nenne en een 16 Adjust the PIP S
34. oof NOTICE Ref Button Description A INFO Provides source and resolution information To lock or unlock the remote B COMP Selects the component source Q press Enter Enter Exit AV Selects the composite video source Exit Enter Exit HDMI2 Selects the HDMI 2 source C PIP Turns picture in picture on or off S V Selects the S video source SDI2 Not available D SWAP Swaps between the main and PIP images E ENTER Selects the highlighted menu choices F SCALING Toggles between aspect ratios FREEZE Freezes the current source image MUTE Turns sound off BRIGHT Adjusts brightness CONTRAST Adjusts contrast AUTO Auto adjustments the VGA source SOURCE Toggles between sources VOLUME Decreases the audio output level VOLUME Increases the audio output level G POWER Turns the LCD panel ON and OFF SCALING FREEZE MUTE VGA Selects the PC RGB source BRIGH ONTRAS AUTO DVI Selects the PC DVI source SOURCE VOLUME VOLUME HDMI1 Selects the HDMI 1 source I P POSITION Toggles between picture in picture positions DISPLAYPORT Selects the displayport source SDI1 Not available J P SOURCE Selects the secondary sub source K MENU and Opens the onscreen display OSD menu or arrow keys selects the previous menu if already open The arrows provide menu navigation and setting adjustment L EXIT Close the OSD menu LCD Panel FHD551 W User Manual 7 020 100996 01 Rev 2 12 2012 CHRISTIE Installation This section pr
35. ovides package handling and installation instructions Package Handling Two people are required to safely lift and install the LCD panel Transport the LCD panel upright with the proper packaging Do not place the LCD panel on its NOTICE side Dropping the panel or applying unnecessary force to the sides of the bezel results in NOTICE permanent damage LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 Installation CHAISTIE Unpack the LCD Panel A WARNING Two people are required to safely lift and install the LCD panel O Save the LCD panel packaging to move or ship the LCD panel in the future Set the LCD panel box in an upright position Remove the banding Remove the white lock handles Lift off the top of the carton Remove the top foam cushion Remove the packing bag pu Qus I Nee With two people lift the LCD panel out of the bottom foam cushion 8 Remove the accessory bag Top of the carton Top foam cushion LCD panel Packing bag Accessory bag Bottom foam cushion o m m oc ou gt Lock handle 1 of 6 10 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Installation LCD Panel Setup NOTICE gt Ww M oc 6 Do not install the LCD panel near any heat sources such as radiators heat registers stoves or other apparatus that produce heat This may cause a fire or electric shock Allow a minimum of 2 in 5 cm spacing from the w
36. power cable with wet hands and avoid A DANGER handling the power cord during electrical storms 1 Hold the interior I O cover against the LCD panel and guide the cables power and video source into the cable bracket 2 Place the exterior I O cover over the interior I O cover and secure it with 4 screws Insert the male end of the power cable into an AC wall socket LCD Panel FHD551 W User Manual 13 020 100996 01 Rev 2 12 2012 Installation CHAISTIE Install the Remote Control Batteries NOTICE NOTICE The remote control is not waterproof To install the batteries follow the instructions provided in the remote control battery compartment Incorrect polarities may cause operator injury battery damage and contamination of the remote controller Use approved AAA batteries and do not mix different battery types or strengths To lock or unlock the remote press Enter Enter Exit Exit Enter Exit Remove the battery cover by lifting the tab of the battery cover Insert two AAA batteries into the remote control Correctly align the polarity of each battery with the polarity markings inside the remote control Close the battery cover Disconnect Power from the LCD Panel Hold the power connector when removing the power cable Removing the power cable by DANGER the cord can damage the wires inside the cable and cause fire or electric shock To avoid risk of electric shock do not touch the power cable
37. s mit diesem gedruckten Handbuch eingeschlossen ist enth lt eine elektronische Kopie auf in deutscher Sprache Vor der Anwendung oder der Instandhaltung dieses Produktes lesen Sie bitte alle Anweisungen I CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano Si prega di leggere tutte le istruzioni prima di utilizzare o riparare questo prodotto c OE8IRI amp d4v77 v a PCAS NTEU EY CODICIA BARSBCORBEDAOC YES CORA II EE mene CBRE SL Hra an rao WE CD Ae HSE el uMXABE BHT UAUC E MES AS 32 MHA Hol SE AA AFS amp amp HO SA BRENES O CD incluido com o impresso livro cont m um eletr nico c pia em Portugu s Por favor lido todas as instrug es antes de usar ou prestando servico esse resultado llocraBnaeMbi B KOMNNEKTe c nokyMeHrauuen KOMNMAaKT AucKk CD cogepxKuT SIIekTDOHHyIO KONMMO PYKOBOACTBa MONIb3OBaTenia Ha PYCCKOM A3bIKe lepen HauanoM NCNONB30BAHHA U3AENVA una npoBeneHus cepBnca noxanylicra npourure BCe WHCTpyKLIMM U3NOXEHHbIe B pyKOBOZICTBe El DC incluido con este manual impreso contiene una copia electr nica en espa ol Por favor lea todas las instrucciones antes de usar o dar servicio a este producto KoMnakT AMCK LUO MOCTAYAETECA 3 UNM APYKOBAHE KepiBHMLITBO MICTUTb eJIeKTDOHHy KOnitO yK palHCbKOIO MOBOW by 1b nacka npouura re Bci incTpykuil nepeg BAKOPUCTaHHAM a60 o6cnyroByBaHHAM LIBOTO MPOAYKTY CHRISTIE Table of Contents Important Safety Informati0N o
38. ting value in the OSD menu a Navigates up in the OSD menu v Navigates down in the OSD menu MENU EXIT Opens the OSD menu or selects the previous menu if the OSD menu is already open Indicator Lights The indicator lights are located at the back of the LCD panel to the left of the LCD panel controls Light Description Green solid Indicates that the LCD panel is operating normally Green blinking Indicates that the LCD panel fan has failed Orange solid Indicates that the LCD panel is in power saving mode Orange blinking Indicates that the LCD panel is not receiving a signal None Indicates that the LCD panel does not have power or is off 020 100996 01 Rev 2 12 2012 Introduction Connection Panel The connection panel is located at the back of the LCD panel Remove the exterior and interior I O panels for access CHAISTIE mm o 0 u gt Qo RS 232C In D Sub 9 pin Component RCA Component Audio RCA L R S Video Composite Video RCA Audio In RCA S Video Component Video Audio Out 3 5 mini jack Infrared Extender 3 5 mini jack z 3 Fr A e O PC Audio In 3 5 mini jack VGA D sub 15 pin DVI D HDCP compliant HDMI 2 HDMI 1 DisplayPort AC IN power cord Power On Off Switch LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Introduction Remote Control The remote control is not waterpr
39. tures or high voltage lines from the immediate vicinity of the LCD panel e Adjust the LCD panel using the OSD menu 41 Troubleshooting LCD Panel Problem The remote control is not functioning White color is not correct 42 CHRISTIE Correction e Verify that the infrared extender cable is installed correctly e Verify that the remote control is not locked Unlock if required See Remote Control on page 7 e Verify that the batteries are fresh and that they are installed correctly Make sure the remote control is aimed at the IR sensor on the back of the display Adjust the color temperature See Image Settings on page 20 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Specifications This section provides the specifications for the LCD panel FHD551 W Specifications are subject to change LCD Panel Specification Active Screen Size Resolution Brightness panel native Contrast Ratio panel native Response Time Aspect Ratio Driver Element Display Colors Pixel Pitch H x W Pixel Arrangement Horizontal Frequency Vertical Frequency Wall Mount Performance Specification Auto Adjust Screen Scaling Power Management Color Adjustment OSD Language LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 Value 54 6 in 138 7 cm 1920 x 1080 16 9 700 cd m2 typ 4000 1 6 5 ms GTG 16 9 a Si TFT Active Matrix 10 bit 1 07 Billion Colors 0 024 i
40. ure position Options include Bottom Right Top Left Top Right and Bottom Left The default is Bottom Right Aspect Ratio Adjusts the aspect ratio Options include Full Screen Pillar Box and Letter Box The default is Full Screen Side by Side Scale Adjusts the side by side scale Options include Zoom In Zoom Out Main PIP Default and Return Auto Scan PIP Adjusts whether auto scan is on or off When auto scan is on the order is VGA HDMI1 HDMI 2 DVI DisplayPort Composite Video S video then Component The default is On Select Source Adjust the picture in picture source Options include HDMI 1 HDMI 2 DVI DisplayPort S Video Composite Video and Component The default is VGA for Main and Composite Video for PiP 22 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHAISTIE Audio Settings Operation Use the Audio Settings menu to adjust volume settings Audio can also be controlled from the remote control Adjust Volume on page 18 See OSD Menu Controls on page 20 for OSD menu control information Audio Settings Volume Bass Treble Balance HDMI Audio Input HDMI DP Audio Input DisplayPort Internal Speakers Off Volume Adjusts the main volume Volume ranges from 0 100 The default is 50 Bass Adjusts the bass level low tones Bass ranges from 0 20 The default is 10 Treble Adjusts the treble high tones Treble ranges from 0 20 The default is 10
41. value 00 01 00 Content CONTRAST Key AUTO Key VOLUME Key VOLUME Key Reset All Un lock Keys Lock Keys Read Serial Number Read Model Name Read Firmware Version Read RS 232C Table Version Read the temperature of the internal thermal sensor 198 260 F 128 127 C Read speed of Fan 0 RPM 40 x Reply value Read speed of Fan 1 RPM 40 x Reply value Wake Up From Sleep VGA Only Wake Up From Sleep VGA Digital RS232 Wake Up From Sleep Never Sleep volume Mute Off Mute On User CHAISTIE CMD HEX 52 43 55 cont Remark 41 4C 4C 4B 4C 43 53 45 52 4D 4E 41 47 56 45 52 54 56 52 54 54 52 53 46 57 46 53 56 4F 4C 4D 55 54 53 43 4D LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 CHRISTIE Main Control CMD Type Value Item Item DEC Other Scheme SCM W R 01 Control Selection cont cont cont cont 02 03 04 LCD Panel FHD551 W User Manual 020 100996 01 Rev 2 12 2012 Reply DEC 01 02 03 04 RS 232C Commands Content CMD Remark HEX Sport 53 43 4D cont Game Cinema Vivid 37 CHAISTIE Compliant Timing The following notation is used in the compliant timing table e O compliant timing for single display is supported e 480i 480i 60 Hz YPbPr e 576i 576i 60 Hz YPbPr fH fV Dot Timing kHz Hz m VGA 640 x 480 31 469 59 94 25 175 37 861 72 809 31 5 37 5 7

Download Pdf Manuals

image

Related Search

Related Contents

MANUAL DE INSTRUÇÕES FORNO FLEX  EXPO 70 - KrissClima  

Copyright © All rights reserved.
Failed to retrieve file