Installation Manual
Contents
1. Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 997 0700 amp 77 CAMERA S www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Camera Discovery Setup and Configuration For camera discovery and setup please use Arecont Vision software AV200 which you can find on the CD included with your camera or at htto www arecontvision com softwares oh The user manual for the AV200 software is included on the CD and is also located on our website To configure the camera use either the AV200 software or the web interface utility The web interface can be accessed by typing the camera IP address into your web browser or by clicking on the web interface button in AV200 The user manual for our web interface is included on the CD and is also located on our website Page 12 support arecontvision com E Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 997 0700 amp 77 CAMERA S www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Wall Mount Accessory MCD WMIT Gasket Alignment features must be aligned for proper installation A Installation Notes Always ensure gaskets are properly seated Use Teflon tape on threaded interfaces 3 8 male to 1 2 female NPT adapter included Mount holes fr2. MicroDome Arecont Vision MicroDome Installation Manual Page 6 support arecontvision com iej 0 Arecont Vision PET E Madein the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 S77 SAMERAS www arecontvision cam avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Focusing the Camera 1 Open alive view of the camera from your web browser or the AV Software provided AV100 or AV200 Loosen the lens lock screw using a phillips head screwdriver if necessary Only do so if lens seems very tight when turning Lock screw should be tightened enough to provide some friction against the lens to avoid focusing problems 3 Manually rotate the lens to adjust the focus until the desired image is obtained 4 Forsome lenses a focus shift will occur once the bubble is in place Hold the bubble up to the lens when focusing to account for the focus shift or see the Focusing Alternate Lenses section below for further instruction Retighten the lock screw if necessary 6 Install the Dome Cover by aligning the captive fasteners with the mating threaded holes on the camera housing 7 When mounting the Dome Cover to the Camera Housing ensure that the gasket is properly seating and not folded Failure to do so may result in water and dust ingress 8 When mounting the Dome Cover to the Camera Housing do not over torque the three captive fast
3. BY ARECONT VISION OR IV THAT ALL LICENSED PROGRAM ERRORS WILL BE CORRECTED For RMA and Advance Replacement information visit ArecontVision com Page 3 support arecontvision com Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 819 937 0700 S770 AMERA S www arecontvision cam avsales arecontvision com MicroLDome Arecont Vision MicroDome Installation Manual Installation Overview Ceiling Gasket aad 7 NPT Port Camera Housing Captive Fasteners Hand Tighten Only Page 4 support arecontvision com E Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 9397 0700 amp 772CAMERA S www arecontvision cam avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Installation Visit http www arecontvision com and check to ensure your camera has the most current firmware For installations in harsh environments it is recommended to use all six mounting screws supplied with your camera to create the best seal possible between your camera and the mounting surface using the supplied gasket 3 If using the NPT port always use Teflon tape around threads to ensure proper sealing After plugging in the network cable check that the indicator LED s are indicating the desired conditions see LED Indicator table 5 Use Arecont Vision software AV100 or AV200 located on the CD or available for download a
4. Installation Manual Mount Template MicroDome Wall Mount Page 16 support arecontvision com Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 9397 0700 amp 772CAMERA S www arecontvision cam avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Mount Template MicroDome Pendant Mount Page 17 support arecontvision com Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 9397 0700 amp 772CAMERA S www arecontvision cam avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Contact Arecont Vision Technical Support one of three ways Online Portal Support ArecontVision com Phone 1 818 937 0700 option 1 Email support arecontvision com Page 18 support arecontvision com E Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 9397 0700 amp 772CAMERA S www arecontvision cam avsales arecontvision com
5. MicroLome INSTALLATION MANUAL AV1455DN S AV2455DN S AV2456DN S AV3455DN S AV3456DN S AV5455DN S SO Arecont Vision Cy 2003 2073 Celebrating 10 Years of Leading the Way in Megapixel Video Made in the USA 1 618 937 0700 877 CAMERA S www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual MicroDome Surface Mount Installation Contents PA CS cece se ates paar ses vate sate esses ace cig ee vie E antctesely anti PA sea oce eb vace E deenceis ase seo ere 3 Warranty MA FOP INU ONS sarecccoosaenanesuteecnnsesassenousacactciansenssuacsemauaneanesteacntsasassenousacaeaubn seen siuaciemauapssemstesaneeaecieisun seclueereeenees 3 Installation VC ECW secret ces ose cosets ceca cicteasena EEEE E ER A EEEE 4 WAST ANA ULOUN sect cise ccuncetecuessenacancncssacecoete E esate cece sayeacabaceasessednncees sehaiveesanuient E 5 OCU SURV CO Ae E a EE EEEE A AE TE AEE E NE 7 Chane TS LEN eenaa E TEE EE E EEEE E AE 8 Focuse Akernate LENS anea EA ETE 8 Dertanp a aAa O a E E E E E E A E E E EEN E E E 9 LEDINO O oes N E E E E E E E sed cogaasesneseraraon bes 10 SUD POT aA E E E ENE E E A antaunes conta enoapiunise becmeosetas 11 Camera Discovery Setup and Configuration s sssssssssssesssssrsssrssssrtssrtrssrtresrresrtesstresrressrtesrttestresrtessernsseeesreeeseene 12 Wal Mount ACCESSOTY sasraiipireniirsrieenisdii ntina EE A AS RERA RENESA EETA ENE RE 13 Pandant M
6. OUNA E SOY ie E 14 Mount Template MicroDome CaMe ra cccssscccssscccsssecceescccaeececenececeseccasceceecesseceseuscessuecessneceeeneessegscetsecessesenees 15 Mount Template MicroDome Wall MOUN cccccscccsssscccessceceseceeeneeecensceceneceseeceseneeseescesseceseneeeseneetsugeceseneseeens 16 Mount Template MicroDome Pendant MOUNL ccccsscccsssccecesececesecccseecaesceeceeceseeessenceseeeceeseneeeseeessuecesseeeeenens 17 Page 2 support arecontvision com S Arecont Vision E Made in the USA 2008 2013 Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 9397 0700 amp 772CAMERA S www arecontvision cam avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Package Contents Mounting Kit Ceiling template 6x Mounting Screws 3 8 NPT Male to 1 2 NPT Female Adapter Network Patch Cable 3x Security Torx Dome Cover Fasteners Arecont Vision CD Manual Warranty Installation Software Warranty Information 3 Year Limited Warranty ARECONT VISION warrants to Purchaser and only Purchaser the Limited Warranty that a each Product shall be free from material defects in material and workmanship for a period of thirty six 36 months from the date of shipment the Warranty Period b during the Warranty Period the Products will materially conform with the specification in the applicable documentation c all licensed program
7. e the lens almost of a turn 250 Put the bubble on and view the image It should be almost in focus Remove the bubble and rotate a degree or two in one direction and view the image with the bubble on Depending on the image you may need to adjust in the opposite direction or continue in the same direction until the desired image is obtained Page 8 support arecontvision com Made in the USA Ad Arecont Vision 10 2003 2013 Celebrating 10 Years of Leading the Way in Megapixel Video 18188370700 877 CAMERA 8 www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Digital Input and Output Use 4 position connector inside camera housing to interface with Digital I O DIGITAL I O BLACK IN NIRE ENTRY SIDE See YJ ORANGE OUT HEATSHRINK TUBING Ey ORANGE YELLOW WHITE BLACK a a AWG28 AWG28 AWG28 AWG28 AME UAS ULI213 Uaa i UTIS i J MOLEX HOUSING 51021 0400 CONTACTS 50079 8000 OR COMP Input Voltage V Measured between and terminals Output Current mA Measured between and terminals Applied Voltage Range 0 80V NOTE Both the input and the output are electrically isolated from the rest of the camera s electrical circuitry via general purpose photo couplers The input is additionally protected with a serial 250 Ohm resistor and a debouncing circuit Duration of any in
8. eners as this will cause the threads to strip Only hand tighten these screws Page 7 support arecontvision com Made in the USA f 2003 2073 ees pem a i E Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERAS www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Changing the Lens 1 Remove the Dome Cover by loosening the captive fasteners Loosen the lens lock screw using a phillips head screwdriver if necessary Only do so if lens seems very tight when turning 3 Manually unscrew the lens this may take several seconds Replace lens Retighten the lock screw if necessary 6 Reinstall Dome Cover per instructions outlined above Focusing Alternate Lenses When focusing the 6mm 8mm 12mm or 16mm lens options you will encounter a focus shift when using the bubble To account for this follow these steps Focus the camera without the bubble Rotate the lens per the chart below The rotation will account for most of the focus shift Put cover with bubble on You should be close to being focused Remove cover and rotate a couple degrees at a time in either direction until you gain the desired image a ae MPM16 0 lt 3 4 CCW MPM12 0 1 ccw_ 90 MPM8 0 gt 1 accw 60 MPM6 0 1 8 CCW Example Using a 16mm lens you will focus the lens without the bubble until you get the desired image Rotat
9. om camera housing to flange are not symmetrical e WN e Alignment features indicated must be properly lined up for mount hole alignment Page 13 support arecontvision com Made in the USA Ad Arecont Vision 10 Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERAS www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Pendant Mount Accessory MCD CMT Installation Notes 1 Always ensure gaskets are properly seated 2 Use Teflon tape on threaded interfaces 3 3 8 male to 1 2 female NPT adapter included 4 Mount holes from camera housing to flange are not symmetrical Alignment features indicated must be properly lined up for mount hole alignment Gasket Alignment features must be aligned for proper installation Page 14 support arecontvision com Made in the USA be ee ieee oe E E 7 Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERAS www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Mount Template MicroDome Camera E Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video Page 15 support arecontvision com 2008 2013 1 818 937 0700 S77 CAMERA S www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome
10. put signal should be at least 5ms to comply with the requirements of the debouncing circuit Page 9 support arecontvision com 0 E Made in the USA Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 9397 0700 amp 772CAMERA S www arecontvision cam avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual LED Indicators established Camera has been accessed Normal operation Yellow Page 10 support arecontvision com KO Arecont Vision Cy 2008 2013 Made in the USA i eee l l Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 8770 AMERA B www arecontvision com avsales arecontvision com MicroDome Arecont Vision MicroDome Installation Manual Support 1 Arecont Vision FAQ Page Located at ArecontVision com 2 Check the following before you call v Restore camera to factory default with AV100 AV200 or the camera webpage v Upgrade to the latest firmware by visiting ArecontVision com v Isolate the camera on a dedicated network and test with AV100 or AV200 v Swap the troubled camera with a known good camera to see if the problem follows the camera or stays at the location 3 Contact Arecont Vision Technical Support one of three ways 1 Online Portal Support ArecontVision com 2 Phone 1 818 937 0700 option 1 3 Email support arecontvision com Page 11 support arecontvision com
11. s accompanying the Product the Licensed Programs will materially conform with applicable specifications Notwithstanding the preceding provisions ARECONT VISION shall have no obligation or responsibility with respect to any Product that i has been modified or altered without ARECONT VISION s written authorization ii has not been used in accordance with applicable documentation ili has been subjected to unusual stress neglect misuse abuse improper storage testing or connection or unauthorized repair or iv is no longer covered under the Warranty Period ARECONT VISION MAKE NO WARRANTIES OR CONDITIONS EXPRESS IMPLIED STATUTORY OR OTHERWISE OTHER THAN THE EXPRESS LIMITED WARRANTIES MADE BY ARECONT VISION ABOVE AND ARECONT VISION HEREBY SPECIFICALLY DISCLAIMS ALL OTHER EXPRESS STATUTORY AND IMPLIED WARRANTIES AND CONDITIONS INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE NON INFRINGEMENT AND THE IMPLIED CONDITION OF SATISFACTORY QUALITY ALL LICENSED PROGRAMS ARE LICENSED ON AN AS IS BASIS WITHOUT WARRANTY ARECONT VISION DOES NOT WARRANT THAT I THE OPERATION OF THE PRODUCTS OR PARTS WILL BE UNINTERRUPTED OR ERROR FREE Il THE PRODUCTS OR PARTS AND DOCUMENTATION WILL MEET THE END USERS REQUIREMENTS III THE PRODUCTS OR PARTS WILL OPERATE IN COMBINATIONS AND CONFIGURATIONS SELECTED BY THE END USER OTHER THAN COMBINATIONS AND CONFIGURATIONS WITH PARTS OR OTHER PRODUCTS AUTHORIZED
12. t our website www arecontvision com for camera discovery and setup see Instruction Manual located on CD or available on our website 6 Adjust the pan and tilt to obtain the desired field of view see Focusing Instructions Lens may be further secured by tightening the lens lock screw using Phillips head screwdriver 8 Install the Dome Cover by aligning the captive fasteners with the mating threaded holes on the camera housing 9 When mounting the Dome Cover to the Camera Housing ensure that the gasket is properly seating and not A N folded Failure to do so may result in water and dust ingress 10 When mounting the Dome Cover to the Camera Housing do not over torque the three captive fasteners as this will cause the threads to strip Only hand tighten these screws Best Practice Tips gt When mounting to vertical surface it is best to use the Wall Mount Accessory MCD WMT which includes a junction box gt For outdoor use it is always best to properly seal the product using caulk around the edges to prevent water ingress from mounting to porous or uneven surfaces gt Use Teflon tape on threaded interfaces gt Useall6 supplied mounting screws for best seal when mounting outdoors Page 5 support arecontvision com Made in the USA Ad Arecont Vision T 2003 2013 Celebrating 10 Years of Leading the Way in Megapixel Video 1 818 937 0700 877 CAMERAS www arecontvision com avsales arecontvision com
Download Pdf Manuals
Related Search