INSTRUCTION MANUAL
Contents
1. LOADING THE LOWER BASKET Carefully load flat plates soup plates dessert and serving dishes positioning them vertically Pots pans and their covers must be loaded upside down When loading soup plates and dessert bowls be sure to leave a gap between them NETTO tr ETT n ILLU 29 User instructions 30 TOP CUTLERY BASKET The basket is designed to take cutlery placed in the spaces provided and long utensils positioned lengthwise The drawer extraction system makes the basket easier to load but it can also be taken completely off its runners by removing the retainers as shown here Take great care to replace the retainers to ensure that the basket does not come off the runners accidentally User instructions CEN D CUTLERY BASKET The basket has removable top grids into which items of cutlery should be inserted to keep them properly spaced and allow water to pass between them effectively The top grids and central lid are in the bag of accessories The central lid functions as a lid only The top grids can be detached and used separately The cutlery should be arranged in an orderly manner inside the basket with the handles pointing downwards Take care during loading to avoid injury from the knife blades The basket is suitable for all types of cutlery except those long enough to interfere with the upper spray arm Ladles wooden spoons and cooking knives can be placed2. Safety instructions e gt LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN PUTING PEOPLE AT RISK NEVER LEAVE THE DISHWASHER DOOR OPEN PEOPLE MIGHT TRIP OVER IT DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE KNIVES OR OTHER SHARP ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE DOWN OR LAID HORIZONTAL IN THE TOP BASKET TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE BASKET AQUASTOP MODELS THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK WHEN THE AQUASTOP DEVICE IS TRIPPED CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE THERE IS A SOLENOID VALVE INSIDE THE WATER INTAKE HOSE DO NOT CUT THE HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO WATER IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY AND FROM THE WATER SUPPLY IMMEDIATELY AFTER INSTALLING THE DISHWASHER PERFORM A QUICK TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW IF THE DISHWASHER FAILS TO OPERATE CORRECTLY DISCONNECT IT FROM THE ELECTRICAL POWER SUPPLY AND CALL THE NEAREST TECHNICAL SERVICE CENTRE DO NOT ATTEMPT TO REPAIR THE APPLIANCE THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE REGULATIONS IN FORCE CO
3. SELF DIAGNOSTICS SYSTEM FAULT Er 01 Er 02 Er 03 Er 04 Er 05 Er 06 Er 07 Er 08 Er 09 DESCRIPTION The anti flooding system where present has been tripped The water level limitation system has tripped The appliance cannot heat the water The temperature sensor is disconnected The appliance cannot take in the water The appliance cannot drain the water from the tank The dishwasher cannot measure the precise water quantity that has been loaded Problem on the water distribution system to the baskets Water intake system malfunction If an alarm occurs the appliance interrupts the program in progress and signals a fault e Alarms E1 E2 E3 E4 E8 and E9 interrupt the current program immediately e The E5 E6 alarms interrupts the running program once the cause is resolved it will bring bach the execution of the program e The alarm ET is visualized at the end of the cycle that comes however brought to the end since the operation of the dishwasher is not harmed To reset an alarm is necessary e Open and close the door or turn off and on the machine At this point is possible to program the dishwasher again If the malfunction persists contact your authorised Service Centre 39 CEN D User instructions 3 TECHNICAL DATA T Width 597 599 mm Depth measured flush with the Free standing 600 mm outer edge of the control panel Semi integrated 570 mm Free standing from 850 mm to 890 mm fr
4. hold of the longer arm and pull the orbital unit upward Wash the arms under a jet of running water and return them carefully to their seat After reassembly check that the spray arms turn freely Otherwise check that they have been installed correctly ORBITAL 35 CEND User instructions 13 36 CLEANING THE FILTER UNIT It is advisable to periodically inspect the centre filter C and if necessary to clean it To remove the filter grip the tabs turn them anticlockwise and lift upwards push the centre filter D from the underside to remove it from the micro filter separate the two parts which make up the plastic filter by pressing the body of the filter in the zone shown by the arrows remove the centre filter by lifting it upwards x a TT j nr a GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE The filters should be cleaned under running water using a stiff brush When removing the filter take care that there are no food residues on it If any residues fall into the washing pit they might block hydraulic components or foul the spray arm nozzles It is essential to thoroughly clean the filters according to the above instructions the dishwasher cannot function if the filters are clogged Carefully replace the filters in their seats to avoid damaging the wash pump PROLONGED DISUSE Run the soak program twice in succession Unplug the power cord from the
5. not dishwasher safe e Wooden dishes pots or pans these may be damaged by the high washing temperatures e Handcrafted items these are rarely suitable for washing in a dishwasher The relatively high water temperatures and the detergents used may damage them e Plastic dishes heat resistant plastic dishes must be washed in the upper basket e Dishes and objects in copper tin zinc or brass these tend to stain e Aluminium dishes items made from anodised aluminium may lose their colour e Silverware silver items may stain e Glass and crystal in general glass and crystal objects can be washed in the dishwasher However certain types of glass and crystal may become dull and lose their clearness after many washings Therefore for these items we recommend using the least aggressive program available e Decorated items the decorated objects available on the market are generally able to withstand washing in the dishwasher although the colours may fade after a great many washes If in doubt as to the fastness of the colours it is advisable to wash just a few items at a time for approximately one month t rie User instructions CEN 7 4 4 Using the baskets The dishwasher has a capacity of 15 place settings LOWER BASKET The lower basket receives the full force of the lower spray arm and should therefore be used for the toughest items with a heavier degree of soiling All types and combinations of loads ar
6. together with any washing program except QuickTime the soak program to SHORTEN the cycle ENERSAVE Indicated option for saving energy EnerSave PROGRAMS TABLE The manual contains the programs table for several models To find the table for your dishwasher compare the program symbols at the top of the table with those on your control panel 11 CEN E MTS User instructions DURATION CONSUMPTION PROGRAMME LOAD CROCKERY AND PROGRAM NUMBER amp CUTLERY PROGRESS MINUTES WATER POWER SYMBOL 1 LITRES KWh 1 1 SOAK A Pans and dishes awaiting 15 35 0 02 RS completion of the load Elige es 2 j 2 NORMAL Cold prewash ECO Crockery and cutlery Wash at 49 C 142 11 6 0 66 normally soiled Rinse at 41 C i Dry e c 3 Cold prewash DELICATE S Delicate dishes with normal HE od 75 12 5 1 1 Qe din Rinse at 70 C Dry 4 ECO Cold prewash ECO Dishes with normal dirt even Wash at 55 C 100 11 1 3 RA with dried on residues Rinse at 70 C S Dry 5 AUTO 40 50 Pans and dishes with normal When the AUTO program is selected the dishwasher 2m dirt washed immediately after recognises the type of dirt and automatically adjusts the S use washing parameters as appropriate SS 6 AUTO 60510 Pans and dishes with normal When the auTo program is selected the dishwasher 60 70 dirt even with dried on recognises the type of dirt and automatically adjusts the gt residues washing parameters as appropriate NI IEC DIN Hot
7. 5 Flexi Tabs QUICK TIME PROGRAMS available in all programs except the soak program Select this option together with any washing program except the soak program to SHORTEN the cycle To activate this option press button light comes on after selecting the program required The option is automatically deactivated at the end of the program ENERSAVE This option reduces the temperature of final rinse saving energy It is activated after selecting the desired program by pressing the button indicator lights Moderately increases the duration of the cycle The option is activated by pressing key and the relative light illuminates to indicate its activation OPTION SELECTION Options are selected by pressing the relative button by the symbol of the option required the light comes on to confirm that the option has been activated e It is not possible to select any options when the soak program is being used e All options except Flexi Tabs are disabled at the end of the wash cycle To disable the Flexi Tabs option press the relative button the light goes out e All options including Flexi Tabs are disabled when a program is CANCELLED after it has begun Flexi Tabs Ideal for multi function detergents this option allows washing to be optimised with full benefits from the combined action tablets When this option is activated any salt and rinse aid in the relative containers will not be used If the option is not pr
8. CEN C4 e A e 5 Cleaning and maintenance Before carrying out any work always unplug the appliance from the electrical supply or switch off the all pole disconnection device 5 1 General warnings and recommendations Avoid the use of acidic or abrasive detergents Clean the outer surfaces and door lining of the dishwasher regularly using a soft cloth moistened with water or with a normal detergent suitable for painted surfaces Clean the door gaskets with a damp sponge Periodically once or twice a year it is advisable to clean the tank and gaskets using a soft cloth and water to remove any deposits CLEANING THE WATER INTAKE FILTER The water intake filter A located at the outlet of the water supply tap needs to be cleaned periodically After having closed the water supply tap unscrew the end of the water intake hose remove the filter A and clean it delicately under running water Reassemble filter A in its seat and carefully screw the water intake hose back into position CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles to prevent possible clogging Wash them under running water and carefully replace them in their seats checking that their rotary movement is in no way impeded e Toremove the upper spray arm unscrew locking ring R e To remove the lower spray arm simply lift it up pulling by the central part e To remove the orbital spray arm assembly take
9. INSTRUCTION MANUAL CEND GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents CEN 1 Safety and operating instructions 2 Installation and hook up 3 Description of the controls 4 Operating instructions 20 5 Cleaning and maintenance 36 6 Troubleshooting 39 Thank you for choosing one of our products You are advised to read this manual carefully it contains all the information you need about the right conditions for the proper safe use of your dishwasher The individual sections are laid out to provide you with a step by step guide to all your appliance s functions the texts are easy to understand and are complete with detailed illustrations Recommendations are given for the correct use of the baskets spray arms containers filters washing programs and for operating the controls Following the cleaning instructions provided here will keep your dishwasher s performance at peak levels in the long term This user friendly manual will provide answers to all your questions about use of the dishwasher INSTALLATION INSTRUCTIONS these are intended for the qualified technician who must carry out the installation hook up and testing of the appliance USER INSTRUCTIONS these consist of recommendations for using the appliance a description of its controls and of the correct cleaning and maintenance procedures CEND Safety instructions 1 Safety and operating instructions THIS
10. LE COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT DISPOSAL MUST BE CARRIED OUT IN ACCORDANCE WITH LOCAL ENVIRONMENTAL REGULATIONS FOR WASTE DISPOSAL FOR MORE DETAILED INFORMATION ABOUT TREATMENT RECOVERY AND RECYCLING OF THIS PRODUCT PLEASE CONTACT YOUR LOCAL CITY OFFICE YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE PRODUCT IN THE EVENT OF A FAULT DISCONNECT THE DISHWASHER FROM THE ELECTRICAL POWER SUPPLY AND SHUT OFF THE WATER TAP DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED DURING TRANSIT IF IN DOUBT CONSULT YOUR DEALER THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY A QUALIFIED TECHNICIAN THIS DISHWASHER MUST BE USED BY ADULTS USE BY PERSONS WITH REDUCED MENTAL AND OR PHYSICAL CAPABILITIES IS ONLY PERMITTED UNDER THE SUPERVISION OF A PERSON RESPONSIBLE FOR THEIR SAFETY KEEP CHILDREN AWAY FROM DETERGENTS AND PACKAGING MATERIALS PLASTIC BAGS POLYSTYRENE ETC AND NEVER ALLOW THEM TO APPROACH OR PLAY WITH THE DISHWASHER SINCE IT MIGHT CONTAIN DETERGENT RESIDUES CAPABLE OF CAUSING PERMANENT DAMAGE TO THE EYES MOUTH AND THROAT AND EVEN LEADING TO SUFFOCATION THE APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS WITHOUT SUPERVISION DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR TURPENTINE WHICH MAY CAUSE AN EXPLOSION DO NOT LOAD DISHES THAT ARE SOILED WITH ASH WAX OR PAINTS
11. MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER BEFORE USING THE APPLIANCE CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN IN COMPLIANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED TO BE USED IN HOUSEHOLD AND SIMILAR APPLICATIONS SUCH AS STAFF KITCHEN AREAS IN SHOPS OFFICES AND OTHER WORKING ENVIRONMENTS FARM HOUSES BY CLIENTS IN HOTELS MOTELS AND OTHER RESIDENTIAL TYPE ENVIRONMENTS BED AND BREAKFAST TYPE ENVIRONMENTS IT COMPLIES WITH THE EEC DIRECTIVES 73 23 89 336 INCLUDING 92 31 AND 93 68 CURRENTLY IN FORCE INCLUDING THE PREVENTION AND ELIMINATION OF RADIO FREQUENCY INTERFERENCE THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE WASHING AND DRYING OF DISHES ANY OTHER USE SHALL BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR USES OTHER THAN THOSE DESCRIBED ABOVE THE NAME PLATE FEATURING THE TECHNICAL DATA SERIAL NUMBER AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF THE DOOR THE NAME PLATE ON THE INNER EDGE OF THE DOOR MUST NEVER BE REMOVED DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED WITHIN THE HOME SEPARATE THE VARIOUS MATERIALS WHICH MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED WASTE COLLECTION CENTRE THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULA
12. NCERNING SAFETY AND ELECTRICAL EQUIPMENT ANY TECHNICAL CHECKS SHOULD BE CONDUCTED EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN REPAIRS CARRIED OUT BY UNAUTHORISED PERSONS WILL INVALIDATE THE WARRANTY AS WELL AS POSING A POTENTIAL HAZARD TO THE USER The manufacturer declines all responsibility for damage to persons or property resulting from failure to observe the above precautions from tampering with even a single component of the appliance or from the use of non original spare parts Installation instructions S EN 2 2 Installation and hook up Remove the polystyrene basket retainers Position the appliance in the desired place of installation The back or sides of the dishwasher may be placed up against walls or other furniture units If the dishwasher is installed near a heat source fit the special insulating panel to prevent overheating and malfunction of the appliance To ensure stability install integrated or built under dishwashers only under continuous worktops and screw them to the adjacent units To facilitate the installation procedure the intake and drain hoses can be positioned in any direction make sure that the hoses are not kinked crushed or pulled too tightly Make sure to tighten the locking ring nut once the pipes have been placed in the direction required A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass Level the appliance on the floor using its adjustab
13. NG The dishwasher is factory set for medium water hardness However it possible to change the setting by turning the dispenser s selector to the desired position the amount of rinse aid dispensed is proportional to the selector position To adjust the rinse aid setting rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it Then use a screwdriver to rotate the rinse aid selector to the desired position Replace the cap turning it clockwise The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains If on the other hand the dishes are sticky or have white streaks it is necessary to reduce the rinse aid setting 238 User instructions 5 24 ADDING THE DETERGENT To open the detergent dispenser cap lightly press the button P Add the detergent and close the cap carefully During the washing cycle the dispenser will be opened automatically L if aN e When a program with hot prewash is selected see program table extra detergent must be placed in the cavity G H depending on models e Use only detergents specially formulated for dishwashers For optimal washing results it is important to use a good quality detergent e The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results Once opened the detergent packs should not be kept fo
14. TIONS IN FORCE THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY WARNING DISHWASHER DETERGENTS ARE ASTRONGLY ALKALINE THEY CAN BE EXTREMELY DANGEROUS IF SWALLOWED AVOID CONTACT WITH SKIN AND EYES AND KEEP CHILDREN AWAY FROM THE DISHWASHER WHEN THE DOOR IS OPEN Safety instructions CEN ue A CHECK THAT THE DETERGENT RECEPTACLE IS EMPTY AFTER COMPLETION OF THE WASH CYCLE OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE CUT OFF THE MAINS POWER CORD AFTER UNPLUGGING IT FROM THE WALL OUTLET AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR CHILDREN LOCKS DOORS ETC THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY YOU WILL HELP PREVENT POTENTIAL NEGATIVE CONSEQUENCES FOR THE ENVIRONMENT AND HUMAN HEALTH WHICH COULD OTHERWISE BE CAUSED BY INAPPROPRIATE WASTE HANDLING OF THIS PRODUCT THE SYMBOL A ON THE PRODUCT OR ON THE DOCUMENTS ACCOMPANYING THE PRODUCT INDICATES THAT THIS APPLIANCE MAY NOT BE TREATED AS HOUSEHOLD WASTE INSTEAD IT SHALL BE HANDED OVER TO THE APPLICAB
15. ashed it saves energy and reduces the program duration Place dishes in both baskets then load the detergent dispenser than less than the normal amount for a full load PROGRAM DELAY The PROGRAM DELAY button can be pressed to delay the start of the washing program by from 1 to 12 24 hours depending on the model This option allows the dishwasher to be operated at the time of day of the user s choice The first time the PROGRAM DELAY button is pressed the option light comes on and 1 h appears on the DISPLAY 9 The button can then be pressed again to set the delay required 2 h 3 h etc If no button is pressed for a few seconds the DISPLAY 9 shows the time left time remaining to the end of the selected program e g 5 40 duration of the washing cycle program delay When the user confirms the program start read the relative section a prewash will be carried out after which the PROGRAM DELAY set will begin and the time remaining on the DISPLAY will gradually be counted down At the end of the delay set the option light goes out and the washing cycle starts N B It is not possible to select the PROGRAM DELAY option once the cycle has begun User instructions CEN 7 TO SAVE ON ENERGY AND PROTECT THE ENVIRONMENT e Always try to run the dishwasher fully loaded e Do not wash the dishes in running water e Use the washing program that is most appropriate for each type of load e Do notcarry out any preliminary r
16. at 70 C Cold prewash Wash at 70 C Cold rinse Rinse at 70 C Wash at 65 C Cold rinse Rinse at 70 C DURATION MINUTI 1 27 60 70 70 85 55 CONSUMPTION WATER POWER LITRES KWh 1 6 5 0 70 12 5 1 15 12 5 1 40 9 1 40 13 1 40 9 5 1 35 1 The cycle duration and power consumption may vary according to the water and room temperatures and the type and amount of dishes A The washing cycle will not take place if the dishwasher door is left open or not properly closed 13 User instructions 3 5 14 3 2 Washing programs The dishwasher is equipped with a control panel described in chapter 3 Description of the controls from which it is possible to carry out all the power switch on switch off and programming operations Before starting a washing program make sure that e The water supply tap is open P e The correct amount of detergent has been added to the dispenser e The baskets have been correctly loaded e The spray arms are able to rotate freely and without obstruction e The dishwasher door is securely closed e SWITCHING ON When the ON OFF button 1 is pressed the dishwasher switches on 6 4 l 2 a SEVSHSH PI nu I s 0000 s3 Qo 8 Ge M amp mit z 5 9 3 PROGRAMMING Programming operations are only possible with the door closed PROGRAM SELECTION Press th
17. change or annul the program see CHANGING A PROGRAM or ANNULLING A PROGRAM 15 CEND User instructions 13 l 16 CHANGING A PROGRAM To change the running program it is necessary e to interrupt the running program see INTERRUPTION A PROGRAM e select the new program e Start the program see STARTING THE PROGRAM ANNULLING A PROGRAM To annul the program e press the START PAUSE button 3 for a few seconds the light of the phase in progress remains on and the light of the program in progress flashes confirmation beep e Keep the START PAUSE button 3 pressed until the PROGRAM PHASES lights 5 go out confirmation beep PO will appear on the DISPLAY and pump out of the water in the tank will begin ending the program at the point where it was interrupted When the operation is complete the PHASES PROGRAM LIGHTS 5 flash The water in the tank will be pumped out and the program will end at the point where it was interrupted When the operation is complete the PROGRAM PHASES lights 5 flash In case that the door is opened during the operation to the next door closing it is going to be necessary to start the program as shown in paragraph STARTING THE PROGRAM The program will resume from the point in which it was interrupted In case that the tub temperature is higher than 50 C the program will start about 60 seconds later User instructions END QuickTime D Z EnerSave 6
18. cle duration and alarms User instructions 3 10 4 d 7 Ge zu eoc PI nn nn 3c sS P Q B M A lliri 5 9 3 1 ON OFF BUTTON 2 SELECTION PROGRAMS BUTTON 3 START PAUSE BUTTON 4 PROGRAMS LIGHTS 5 PHASES PROGRAM LIGHTS SALT WARNIN LIGHT operates only on some models Illumination of this light denotes a regenerating salt warning level 7 N RINSE AID LIGHT 8 OPTIONS 9 INFORMATION DISPLAY lt lt OPTIONS 8 gt gt Depending on the model this zone may contain one or more of the following options identified by the relative symbols and described in more detail in the relevant sections of the manual It is not possible to select any options when the soak program is being used All options except Flexi Tabs are disabled at the end of the wash cycle To disable the Flexi Tabs option press the relative button the light goes out User instructions CEN D C Flexi Tabs Option recommended for the use of multi function tablet FlexiTabs detergent 7o c HYCLEAN Increases the temperature of the final hot rinse to 70 C to Hyclean ensure a further reduction in the bacteria level yo ion Spread HALF LOAD WASH qum Allows washing of just a few dishes placed in both baskets Flexi Zone PROGRAM DELAY Allows the program to be set to start with a delay of up to 9 12 Delay Or 24 hours depending on the model E 9 QUICK TIME 4A Select this option
19. d have it replaced by the manufacturer or an Authorized Technical Service Centre in order to avoid any risk C EN Installation instructions FOR GREAT BRITAIN ONLY e THIS APPLIANCE MUST BE EARTHED Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug to change a fuse in this type of plug use an A S T A approved fuse to BS 1362 type and proceed as follows 1 Remove the fuse cover A and fuse B 2 Fit replacement 13A fuse into fuse cover 3 Refit both into plug cover is lost the plug must not be used until a correct replacement is fitted Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug Replacement fuse covers are available from your local electrical store f The fuse cover must be refitted when changing a fuse and if the fuse rie User instructions CEN D 3 Description of the controls 3 1 Front panel The ON OFF is on the top edge of the panel and all the dishwasher s other controls and monitoring devices are on the central display Programming and option selection are only possible with the door closed NOTA The displays illustrated in the instruction manual are purely guideline symbols programs and options may vary depending on the model purchased EET The 4 figure INFORMATION DISPLAY 9 informs Li the user about the program delay time remaining washing cy
20. e PROGRAM SELECTION button 2 several times until the light of the program required comes on As the user scrolls through the programs the INFORMATION DISPLAY 9 will show the scheduled duration of each program and the PHASES PROGRAMS lights 5 will indicate the washing phases it includes User instructions CENT STARTING THE PROGRAM To start the dishwasher press the START PAUSE button 3 for a few seconds until the light of the first phase of the selected program starts to flash confirmation beep As the program runs the PHASES PROGRAM lights 5 will indicate the current cycle status I if E S 99 amp KA 00 00 ioi M 5 The light of the phase in progress will flash while the lights of the subsequent phases remain on Amm amp AN t my SS Prewash Wash Rinse Dry END OF PROGRAM At the end of the program a short beep sounds the word End appears on the DISPLAY 9 and the PHASES PROGRAMS 5 lights flash Pressing the SELECTION PROGRAMS 2 button clears the word End from the display and the dishwasher is ready for a new cycle INTERRUPTION A PROGRAM To interrupt a program in progress e press the START PAUSE button 3 for a few seconds the light of the phase in progress remains on and the light of the program in progress flashes confirmation beep e you may now restart the program by pressing button 3 again until it restarts or
21. e end should be positioned at a height of between 30 and 100 cm and should never be submerged in water If a horizontal drain extension hose is used for a maximum of 3 m the drain hose can be placed at a maximum height of 85 cm from the ground Installation instructions VEN 2 2 Electrical connection and precautions CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN FORCE THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD IN THE EVENT OF DAMAGE TO THE SUPPLY CORD HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE DO NOT USE ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD A IT IS NECESSARY TO INSTALL IN THE FIXED WIRING AN ALL POLE DISCONNECTION DEVICE HAVING A GAP BETWEEN CONTACTS OF AT LEAST 3 5MM AFTER INSTALLATION THE DISCONNECTION DEVICE HAS TO BE EASY TO REACH THE CONNECTION TO THE MAINS MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN IN ACCORDANCE TO THE SCHEME SHOWN BELOW AND THE REGULATIONS IN FORCE L brown N blue yellow green 20 mm In the event of damage to the supply cor
22. e permitted provided that the dishes pots and pans are arranged with all the soiled surfaces exposed to the water jets coming from the bottom Depending on the models the basket may be equipped with some or all of the following accessories Plate racks which can be laid flat when not in use e g to accommodate pans bowls etc To stow the racks flat pull them upward and turn them towards the inside of the basket A ES e Anti drip inserts which improve the TE drying of dishes They may be supplied fitted on the basket or in the accessories bag in this case to use them simply fit them into place as shown 27 User instructions S 28 Supports for cups and long objects ladles spoons etc in the rear can be tipped to the vertical position when not in use Glass holder Support for long stem glasses When lifted out of the stowed position 0 it snaps into three different positions 1 2 3 2 position fold down supports 1 2 In position 1 vertical they can be used to take plates while in position 2 slanted they provide support for long stem glasses which will be held in place by the glass holder Adjustment raise point P as shown until the support turns into position 2 TT T User instructions CEN D To lie completely flat lift the end and turn it towards you so that the retainer F rotates into place above point S
23. h the button for a few seconds the dishwasher will automatically return to standard mode quitting the adjustment mode 4 2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door the detergent dispenser is on the left and the rinse aid dispenser is on the right H EL With the exception of the SOAK program before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser The rinse aid on the other hand should only be added as required 22 User instructions CEN D ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining it is automatically added to the water during the final rinse cycle from the container situated on the inner side of the door To add rinse aid Open the door Rotate the container cap anticlockwise by 1 4 of a turn and remove it Add the rinse aid until the container is full approximately 140 cc The optical level indicator on the side of the cap should be completely obscured Refill the rinse aid when the optical level indicator becomes clear again or when the rinse aid warning light illuminates Replace the cover and turn it in a clockwise direction Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam ADJUSTING THE RINSE AID DISPENSER SETTI
24. he water supply M amp check that the water is clear and free of impurities to prevent damage to the appliance The dishwasher must always be connected to the water system with new hoses old or used hoses must never be reused CONNECTING TO THE WATER SUPPLY em Connect the intake hose to a cold water supply with 34 hi gas thread inserting the filter A supplied with the T dishwasher Take care to screw the hose firmly into H place with your hands and then complete by f tightening about 1 4 of a turn with pliers Gh m In dishwashers equipped with the ACQUASTOP device the filters is already fitted inside the threaded m ring The dishwasher can also be connected to a hot water supply not exceeding 60 C Supplying the appliance with hot water cuts down the washing time by approximately 20 minutes but slightly reduces its effectiveness Make the connection to the domestic hot water supply using the same procedure described for connecting to the cold water supply DRAIN CONNECTION ce Insert the dishwasher s drain hose i i i into a drain pipe having a diameter of at least 4 cm or alternatively place it inside the kitchen sink using the plastic support provided taking care not to crush or excessively bend the hose It is important to prevent the hose from coming loose and falling For this purpose the plastic support is equipped with a hole for tying it to 1 the wall or water tap min 4 cm_ MAX 100 cm The fre
25. in the upper basket making sure that the knife blades do not protrude from the basket The cutlery basket slides across the dishwasher and can be placed in any position to allow optimal use of the space in the bottom basket 31 User instructions 32 UPPER BASKET It is recommended to load the upper basket with small or medium sized items such as glasses small plates tea or coffee cups shallow bowls and light objects made from heat resistant plastic If the upper basket is used in the lowermost position it can also be loaded with serving dishes provided they are only slightly soiled LOADING THE UPPER BASKET Load plates facing forward cups bowls etc must always be facing downwards The left side of the basket can be loaded with cups and glasses on two levels In the centre section plates and saucers can be loaded vertically into the supports provided Loading examples User instructions CEN D a Depending on the models the basket may be equipped with some or all of the following accessories Supports for cups or long objects ladles spoons on the left can be tipped to the vertical position when not in use Long stemmed glass holder on the left to use simply lift and fix onto the hooks provided Cutlery racks on the right designed for knives and teaspoons for teaspoons pull out the sliding support The racks can be tipped to the vertical p
26. ing There are generally no constraints on the washing of domestic dishes but in certain cases it is necessary to take their characteristics into account Before loading the dishes into the baskets it is necessary to e remove coarse food remains e g bones fish bones etc which may clog the filter or damage the wash pump e soak any pots or pans with burnt on food remains on the bottom to facilitate removal then load them into the LOWER BASKET There is no need to pre wash the dishes under running water before loading them into the baskets since this only wastes water Correct loading of the dishes helps ensure optimal washing results 25 EN User instructions TU 26 WARNING e Make sure that the dishes are securely in place so that they cannot tip over or obstruct the rotation of the spray arms during the washing cycle e Do not place very small objects in the baskets as these could fall and obstruct the spray arms or the wash pump e Containers such as cups bowls glasses and pots should always be loaded with the opening facing downwards and with any cavities at an angle to allow the water to drain out e Do not stack dishes or place them in such a way that they cover one other e Do not place glasses too close together because they may knock against each other and break or there might be staining at the point where they touch MAKE SURE that the items being washed are dishwasher safe Items which are
27. insing e If available connect the dishwasher to a hot water supply up to 60 C TO CUT DOWN ON DETERGENT CONSUMPTION AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment To avoid using excessive amounts of detergent and to save on electricity observe the following e separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures e do not pour the detergent directly on the dishes REMOVING THE DISHES At the end of the washing program wait at least 20 minutes before removing the dishes to allow them to cool down To prevent any water droplets on the upper basket from falling on the dishes in the lower basket it is advisable to unload the lower basket first and then the upper basket 19 CEND User instructions E 20 0 4 Operating instructions Once the dishwasher has been correctly installed prepare for use as follows e Adjust the water softening system present only on some models e Add the regenerating salt only on some models e Add the rinse aid and detergent 4 1 Using the water softening system only on some models The amount of scale contained in the water water hardness index can cause whitish staining on the dry dishes which tend to become dull over time The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardne
28. le feet This operation is essential for ensuring correct operation of the dishwasher Ww forbidden A dishwasher can be built in underneath a conventional hob provided there is no break in the kitchen worktop and the dishwasher and hob are installed and secured correctly so that no hazards are generated When installing the dishwasher in a compartment next to one or more other appliances it is essential to comply with all the recommendations provided by the appliance s manufacturer minimum distances installation procedures etc f Building in a dishwasher underneath a ceramic hob is absolutely For free standing models only Installing a hob on top of a free standing dishwasher is absolutely forbidden If the appliance is not built in and is therefore accessible on on side the door hinge area must be covered for safety reasons injury hazard The covering fixtures are available as an accessory from specialist dealers or the After Sales Service To build in the dishwasher the special kit must be purchased from authorised dealers or the After Sales Service Some models are equipped with only one adjustable foot at the rear which can be adjusted by turning the screw on the lower front part of the appliance VEN 7 Installation instructions p 4 2 1 Water supply connection Preventing the risk of clogging or damage if the water pipe is new or Y 1 has not been used for a long time before connecting to t
29. om 890 mm to 930 mm Heighidependingonimoders Semi integrated from 820 mm to 890 mm from 860 mm to 930 mm Capacity 15 Standard place settings Water supply pressure min 0 05 max 0 9 MPa min 0 5 max 9 bar Electrical characteristics See rating plate 40
30. osition when not in use Fixed or movable racks in the middle The movable supports can be fixed vertical resting on the bottom of the basket when not in use or set in the intermediate position as required ur Nara ennt M 33 IEN m Z VEN User instructions m ADJUSTING THE UPPER BASKET The height of the top basket can be adjusted to allow large dishes or pans to be placed in the bottom basket The adjustment procedure may be type A or B depending on the dishwasher model purchased Version A pull out with adjustment in two positions e Pull out both the basket guides e Remove the stops first releasing them as shown in the diagram e Pull out the basket e Fit the upper or lower pair of wheels into the guide depending on the setting required e Return the stops to their original position The left hand and right hand sides of the basket must always be set at the same height Version B with adjustment in three positions on both sides The sides of the basket must always be set at the same height e Raise the basket by pulling on the top edge 1 to the first or second catch depending on the height required e To lower the basket first release it by pulling the release lever 2 Adjustment is also possible with the basket loaded but in this case when lowering the basket it should be held steady with one hand to avoid knocking the dishes 34 User instructions
31. ovided we recommend the use of conventional products separate detergent salt and rinse aid because with conventional washing cycles combined products might create problems such as a white deposit poor drying results and residues left on dishes N B When the salt and rinse aid containers are empty the relative lights will remain on even if the Flexi Tabs option is selected IMPORTANT when no longer required the option must be deactivated by pressing the relative button the light goes out 17 CEND User instructions 13 l T a Hyclean Flexi Zone 18 s N Delay If the water hardness has been set on a value above H3 and the Flexi Tbas option is activated the relative light flashes warning of a setting error Multi function products are not suitable for use with very hard water this does not prevent the use of the option but the washing results might not be of the best HYCLEAN Increases the temperature of the final hot rinse to 70 C to ensure a further reduction in the bacteria level If the temperature in the tank falls during this stage of the program e g because the door is opened or due to a power blackout the light of the option and the program lights flash to warn that the additional washing phase has not been completed successfully This does not mean that the wash program has been less effective than usual SPREAD HALF LOAD Suitable when there are not many dishes to be w
32. prewash SURER Wash at 70 C Very dirty pans and dishes Cold rinse 2 155 15 5 1 60 even with dried on residues Rinse at 70 C ux Dry Only run the soak program with half loads Options cannot be used with the soak program Reference program as per AS NZS 2007 The cycle duration and power consumption may vary according to the water and room temperatures and the type and amount of dishes 1 or 2 cold rinses depending on the model 12 User instructions QUICK TIME PROGRAMS see relevant section for explanation of functioning modes The ENERSAVE option cannot be used with soak ultra clean or any programs which do not include the final drying stage PROGRAMME NUMBER E SYMBOL 8 RAPID 27 Vo 5 cb tauickTime 9 DELICATE QUICK Lee 10 ECO QUICK ECO 11 DAILY QUICK Auto 40 50 Se 12 INTENSIVE me 13 STRONG an FAST LOAD CROCKERY AND CUTLERY Dishes with light dirt washed immediately after use Dishes with normal dirt even with dried on residues Dishes with normal dirt washed immediately after use Dishes with normal dirt washed immediately after use Dishes with normal dirt even with dried on residues Mixed dishes with normal dirt without dried on residues PROGRAM PROGRESS Wash at 38 C Rinse at 50 C Cold prewash Wash at 50 C Cold rinse Rinse at 70 C Cold prewash Wash at 55 C Cold rinse Rinse at 70 C Wash at 70 C Cold rinse Rinse
33. r too long otherwise the detergent loses its effectiveness e Do not use detergents formulated for washing dishes by hand because they produce a great deal of foam and may negatively affect the operation of the dishwasher e Add the correct amount of detergent An insufficient amount of detergent will result in a partial removal of dirt from the dishes whereas an excessive amount is wasteful and does not improve the washing results e The market offers liquid and powder detergents with differing chemical compositions which may contain phosphates or be phosphate free but contain natural enzymes Detergents containing phosphates are more effective against grease and starch at temperatures above 60 C Enzyme detergents on the other hand are also effective at lower temperatures from 40 to 55 C and are more easily biodegradable With enzyme detergents it is possible to obtain at low temperatures comparable results to those which can only be achieved at 65 C using traditional detergents For the safeguarding of the environment we recommend the use of phosphate and chlorine free detergents User instructions V EN 7 amp p The introduction of detergent into the rinse aid dispenser even in liquid form will damage the dishwasher 4 3 General warnings and recommendations Before using the dishwasher for the first time it is advisable to read the following recommendations concerning dish types to be washed and their load
34. socket Leave the door slightly open in order to prevent the formation of unpleasant odours inside the washing tank Fill the rinse aid dispenser Shut off the water supply tap User instructions EN BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE e Check that there are no deposits of sludge or rust inside the water pipe if there are allow the water to run from the water supply tap for a few minutes e Plug the power cord back into the socket e Reconnect the water intake hose and open the tap again TROUBLESHOOTING MINOR PROBLEMS In some cases it is possible to remedy minor problems by referring to the following instructions If the program fails to start check that the dishwasher is connected to the electrical power supply there is no power failure the water tap is open the dishwasher door is properly closed If water remains inside the dishwasher check that e the drain hose is not kinked e the drain siphon is not obstructed e the dishwasher filters are not clogged If the dishes are not being cleaned properly check that the correct amount of detergent has been added there is regenerating salt inside the special container the dishes are being loaded correctly the selected program is suitable for the dish types and their degree of soiling all the filters are clean and positioned correctly e the spray arm nozzles are not obstructed e there is no object obstructing the rotation of
35. ss of the water The dishwasher is factory set for water hardness level 3 average hardness 41 60 dF 24 31 dH When using water of medium hardness the regenerating salt container should be refilled after approximately 20 washing cycles The salt container can hold approximately 1 7 Kg of salt in grains The container is situated at the bottom of the dishwasher After removing the lower basket unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher Before replacing the cap remove any salt residues from around the opening e When using the dishwasher for the first time in addition to the salt it is also necessary to add one litre of water to the container e Each time the salt container is refilled make sure that the cap is securely closed The mixture of water and detergent must never penetrate the salt container as this would compromise the operation of the regeneration system In the event of this occurring the warranty will be invalidated e Only use regenerating salt specially formulated for domestic dishwashers If using salt tablets do not fill the container completely LT User instructions CEN aD e Do not use table salt as it contains insoluble substances which over time may damage the water softening system e When necessary refill the regenerating salt container before Starting the washing program In this wa
36. the spray arms 37 EN 38 User instructions OX If the dishes fail to dry or remain dull check that e there is rinse aid inside the special container e the rinse aid dispenser setting is correct e the detergent used is of good quality and has not lost its effectiveness for example through incorrect storage with the box left open If the dishes show signs of streaking staining etc check that e the rinse aid dispenser setting is not too high If there are visible traces of rust inside the tank e the tank is made of steel and therefore any rust marks are due to external elements fragments of rust from the water pipes pots cutlery etc Special products are commercially available to remove such marks e check that the amount of detergent being used is correct Certain detergents can be more corrosive than others e check that the cap of the salt container is securely closed and that the water softening setting is correct av If after following the above troubleshooting instructions the problem Jj dr 5 persists call the nearest After Sales Centre p Wee WARNING any operations performed on the appliance by unauthorised persons are not covered by the warranty and shall be paid for by the user User instructions CEN 6 Troubleshooting The dishwasher is equipped with a self diagnostics system that is capable of detecting and signalling a number of possible faults TABLE OF FAULTS DETECTED BY THE
37. y the excess saline solution will be immediately removed by the water the prolonged presence of salt water inside the tank may lead to corrosion Be careful not to confuse the salt and detergent packages adding detergent to the salt container will damage the water softening system ADJUSTING THE WATER SOFTENING SYSTEM available in all programs except the soak program The dishwasher is equipped with an electronic device for adjusting the water softening setting according to the hardness of the water To adjust the water softening setting proceed as follows e Keep the SELECTION PROGRAMS button 2 pressed for a few seconds until H3 default value appears on the DISPLAY 9 e Keep pressing the SELECTION PROGRAMS 2 button again to scroll through the setting values available in sequence from H B to H 5 Select the most suitable value referring to the Water hardness table for guidance e To exit the programming mode press the START PAUSE button 3 or do not touch the keypad for 2 seconds to allow the system to exit the mode automatically 21 CEN User instructions 3 WATER HARDNESS TABLE WATER HARDNESS ERR German degrees dH French Degrees dF HO Bnd ud NO SALT 5 15 8 25 HT 16 23 26 40 He 24 31 41 60 H3 32 47 61 80 H4 48 58 81 100 H5 Contact your local water board for information on the hardness of your water supply After adjustment or display of the current setting simply do not touc
Download Pdf Manuals
Related Search