Controll-A-Door® P
Contents
1. Controll A Door P SECTIONAL TILT DOOR OPENER Description B amp D s Controll A Door P CAD P automatic opener is driven by a strong and reliable AC motor With added features and improved styling it is designed to suit most types of sectional and tilting residential garage doors PART NO 062500 4 Piece C Rail Version Contains 062506 Powerhead 062501 4 piece 2 3m C Rail Chain kit 077099 240V 40W ES rough service globe PART NO 062551 1 Piece C Rail Version Contains 062506 Powerhead 062551 1 piece 2 5m C Rail Chain kit 077099 240V 40W ES rough service globe Motor Specifications Rated Pull Force 800N Stand by Power 5 5W Rating 230V Motor Type Speed Volts Current Drive Mechanism Gears Drive Length of Travel Travel Rate Lamp Door Linkage Safety Personal Electronic Electrical Limit Device Limit Adjustment Start Circuit Dimensions Length overall Headroom Required Hanging Weight Receiver Operating Frequency Transmitter Capacity Dip Switch Capacity Keypad Code Warranty Warranty Years Product Code 062501 062551 Permanent split capacitor 1500 rpm 230 240 Volts AC 50Hz only 2 0 amperes 16 1 worm gear reduction Chain with one piece trolley on steel C Rail Adjustable to 2 29m 71 2 feet 127mm 5 per second On when door starts off 21 2 minutes after stop Adjustable door arm Pull cord trolley rel2. on Replace light bulb 40 Watts maximum Replace burned out bulbs with rough service light bulbs Opener won tactivate due to power e Pull manual release rope and handle down and back to disconnect trolley Door can be opened and 12 Opener light does not turn off closed manually When the power is restored pull the manual release handle straight down The next time e There may be a defective Bare the ceilingior wall the opener is activated the trolley will reconnect receptacle The unit must be earthed e The Emergency Key Release accessory if fitted disconnects the trolley from outside the garage in 13 Opener strains or reversed during opening case of power failure e Door may be unbalanced or springs are broken Close door and use manual release rope and handle to disconnect trolley Open and close door manually A properly balanced door will stay in any point of travel while being supported entirely by its springs If it does not call for professional garage door service to correct the problem Do not change force settings NUMBER OF FLASHES PROBLEM 1 Safety infra red beam interrupted incorrectly aligned or an object has interrupted the IR sensor for more than 4 seconds 2 Safety infra red beam system cable short circuited or incorrectly connected 3 Keylock or door control panel short circuited 4 Safety infra red sensor slightly incorrectly aligned dul
3. range e Use outside coaxial antenna adapter to move antenna 5 Door reverses for no apparent reason and opener light doesn t blink e 5 something obstructing the door Pull manual release handle Operate door manually If it is unbalanced or binding call for professional garage door service e Clear any ice or snow from garage floor area where garage door closes e Review Force Settings Open and close the door in learn mode for several 3 5 consecutive cycles to allow the operator to adjust to inconsistent doors f door reverses in FULLY CLOSED position re learn travel limits Repeat safety reverse test after adjustment is complete The need for occasional adjustment of the force and limit settings is normal Weather conditions in particular can affect door travel 6 Door reverses for no apparent reason and opener light blinks for 5 seconds after reversing e Check the Safety Infrared Reversing Sensor if you have installed this accessory If the light is blinking correct alignment Note Continuously holding down the door control button will allow the door to close if the protector system is not properly aligned The transmitter will not close the door The opener lights will blink 7 Opener noise is disturbing in living quarters of home e I operational noise is a problem because of proximity of the opener to the living quarters Vibration Isolator Kit included with the operator can be installed Thi
4. ease Push button and stop Push button and automatic reversal in down direction Push button and automatic stop in up direction Independent up and down force adjustment screws Motor overload protector and low voltage push button wiring Circuit actuated by limit nut Screwdriver adjustment on side panel Low voltage push button circuit 3 23m 1221 2 50mm 14 5kg 32 16 433 92MHz 12 1 1 5 years An alesco Company Controll A Door P MEER 062501 062551 SECTIONAL TILT DOOR OPENER Features 4 Trouble shooting e C Rail system encloses moving parts ensuring a safer amp maintenance cleaner looking rail system Care of Your Opener e Automatic force sensing When properly installed opener will provide high Chain drive for greater torque handling performance with a minimum of maintenance The Chain noise reduction pads opener does not require additional lubrication e 3 Channel transmitter Limit and Force Adjustments These adjustments must A be checked and properly set when is installed Positive locking Only a screwdriver is required to adjust the limits e n built automatic safety reverse system Weather conditions may cause some minor changes in the door operation requiring some re adjustments particularly during the first year of operation Follow the Courtesy light pre set to 2 5 minutes user manual instructions carefully and repeat the safety rev
5. erse test after any adjustment Smart button receiver Manual disengagement cord Maintenance of Your Opener Once a Month Automatic reset after a power failure 433 92MHz frequency e Manually operate door If it is unbalanced or binding call for professional garage door service Method of operation e Check to be sure door opens amp closes fully Adjust limits and or force if necessary Activate the operator by either the door control button outside key switch or keyless entry system the remote control transmitter or manually open the door by pulling the release handle down and back toward the operator Twice a Year e Repeat the safety reverse test Make any necessary adjustments e Check chain tension Disconnect trolley first Adjust if Door type necessary Once a Year Standard residential sectional overhead and tilting garage e Oil door rollers bearings and hinges The opener does doors not require additional lubrication Do not grease the door tracks RP 07 06 Controll A Door P Product Code 062501 062551 SECTIONAL TILT DOOR OPENER Trouble shooting guide 1 Opener doesn t operate from either door control or remote e Does the opener have electric power Plug lamp into outlet If it doesn t light check the fuse box or the circuit breaker Some outlets are controlled by a wall switch e Have you disengaged all door locks Review installation instruction warnin
6. gs in your opener installation manual e lsthere a build up of ice or snow under door The door may be frozen to ground Remove any obstruction e garage door spring may be broken Have it replaced e Repeated operation may have tripped the overload protector in the motor Wait 15 minutes Try again 2 Opener operates from remote but not from door control e s door control button lit If not remove the bell wire from the opener terminals Short the red and white terminals by touching both terminals at the same time with a piece of wire If the opener runs check for a faulty wire connection at the door control a short under the staples or a broken wire e Are wiring connections correct 3 Door operates from door control but not from remote e Check battery Replace battery if necessary e lsthe light at the wall control flashing Press button with key symbol to unlock the opener against remote controls e lsthe receiver LED flashing at the back side of the opener when the transmitter is pressed The opener receiver must re learn the remote control code e f you purchased new remote control then check on carton of remote control for compatibility or call the Service Hotline 4 Remote has short range e ls battery installed If needed change the battery e Change the location of the remote control on the car e metal garage door foil backed insulation or metal siding will reduce the transmission
7. l or flashing sensor LED indicator 5 No motor speed detected after one second Motor has stalled or the electronics did not recognise the motor speed monitoring system The opener stops or reverses door within 1 second 6 Motor speed sensor caused the door to reverse Force Setting Rapid Flashing Remote control signal being received Opener possibly not programmed on remote control RP 07 06 Controll A Door P Product Code 062501 062551 SECTIONAL TILT DOOR OPENER Spare parts list ITEM NO PART NO DESCRIPTION 1 62132 Block Terminal 62204 Power Supply Cord 62206 Capacitor 62216 Gear Kit Drive Worm 62232 Sensor Assembly RPM 62528 RF Module 27MHz 2 3 4 5 6 7 62529 Receiver Logic 433 End Panel CAD P 8 62530 Assy Motor CAD P 9 0 1 2 3 4 5 62531 Assy Limit Switch CAD P 62532 Lamp Socket CAD P 62533 Lamp Lens CAD 62534 Wiring Harness CAD P 62535 Straps Rail Chassis CAD P 62547 Assy Gear and Sprocket CAD P 62543 Belt Pulley Motor C Rail 13 15 Jn 12 lt 4 An 4 alesco Company Controll A Door P EN SECTIONAL TILT DOOR OPENER Notes 07 06
8. s kit was designed to reduce the sounding board effect and is easy to install 8 The garage door opens and closes by itself e Delete all remote controls and reprogram e sure remote push button is not stuck e Disconnect all push buttons or key switches attached and wait one day 9 Door stops but doesn t close completely e Review Limit Adjustment section Repeat safety reverse test after any adjustment of door arm length close force or down limit See overleaf for continuation of Trouble shooting guide An 4 alesco Company Controll A Door P Product Code 062501 062551 SECTIONAL TILT DOOR OPENER 10 Door opens but won t close 14 Opener motor hums briefly then won t work e Check the Safety Infrared Reversing Sensor if you e Garage door springs are broken see no 13 have installed this accessory If the light is blinking e f problem occurs on first operation of opener door is correct alignment locked Disable door lock If chain was removed and e f opener light does not blink and it is a new reinstalled the motor may be out of phase Remove installation check the down force Repeat the safety chain cycle motor to down position Observe drive reverse test after the adjustment is complete sprocket When it turns in clockwise direction and stops in down position re install chain Repeat safety reverse test after adjustment is complete 11 Opener light does not turn
Download Pdf Manuals
Related Search