Debugging MCU Board for 100-pin 0.5mm
Contents
1. Co A er 0 50 C i 13 00 17 00 Unit mm Figure 4 Reference Pad Pattern and Dimensions of the Debugging MCU Board ROE5562N8PFK10 R20UT0217EJ0100 Rev 1 00 Page 4 Dec 16 2010 RENESAS ROE5562N8PFK10 User s Manual 7 Notes on Usage READ the following warnings before using the debugging MCU board Incorrect operation will damage the debugging MCU board and user system The USER PROGRAM will be LOST Notes on Handling the Debugging MCU Board Take full care not to touch any parts or cause short circuits on the debugging MCU board e Protect the debugging MCU board from excessive physical shock Do not alter the debugging MCU board If any alteration is attempted the debugging MCU board will no longer be supported e The MCU installed on the debugging MCU board is only for use in debugging Do not remove the MCU from the board to use it for other purposes For purchasing the NQPACK100SD ND YQPACK100SD and HQPACK100SD contact the following Tokyo Eletech Corporation http www tetc co jp e_index htm Notes on Turning the Power On e Do not apply a power voltage that is beyond the range guaranteed for the MCU e Only supply power to the debugging MCU board and connected parts after having connecting all cables Notes on Connecting the Debugging MCU Board e Cables must not be connected or removed while the power is on e Before connecting the debugging MCU board and user system check that the pin 12. All rights reserved Colophon 1 0
3. for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncomplianc
4. locations on both sides are correctly aligned with each other Notes on Rewriting the Flash Memory e The number of times that the flash memory in the MCU installed on the debugging MCU board can be programmed is limited If an error in erasure occurs during debugging replace the debugging MCU board Notes on Debugging e The debugging MCU board is only usable for debugging when it is connected to the user system e Debugging by the debugging MCU board alone is not supported Notes on Starting the Debugger and Selecting the MCU Type e Select the MCU type for use in the device name section of the Initial Settings dialog box on initiation of the debugger Notes on Designing the User System Pull the levels on the EMLE pin down to 4 7 KQ to 10 KQ Pull the levels on the MDO and MD1 pins up to 4 7 KQ to 10 KQ and select the single chip mode Pull up or down the level on the MDE pin according to the endian used The output of the reset circuit of the user system must be open collector Notes on the Flash Development Toolkit FDT e Do not use the FDT when using the debugging MCU board Notes on the Writing the On chip Flash Memory Mode e Do not use the writing the on chip flash memory mode when using the debugging MCU board Notes on the D A converter e When using the debugging MCU board the D A converter function cannot be used R20UT0217EJ0100 Rev 1 00 Page 5 Dec 16 2010 RENESAS ROE5562N8PFK10 User s Manual Pr
5. 100083 PR China Tel 86 10 8235 1155 Fax 86 10 8235 7679 Renesas Electronics Shanghai Co Ltd Unit 204 205 AZIA Center No 1233 Lujiazui Ring Rd Pudong District Shanghai 200120 China Tel 86 21 5877 1818 Fax 86 21 6887 7858 7898 Renesas Electronics Hong Kong Limited Unit 1601 1613 16 F Tower 2 Grand Century Place 193 Prince Edward Road West Mongkok Kowloon Hong Kong Tel 852 2886 93 18 Fax 852 2886 9022 9044 Renesas Electronics Taiwan Co Ltd 7F No 363 Fu Shing North Road Taipei Taiwan Tel 886 2 8175 9600 Fax 886 2 8175 9670 Renesas Electronics Singapore Pte Ltd harbourFront Avenue 06 10 keppel Bay Tower Singapore 098632 Tel 65 6213 0200 Fax 65 6278 8001 Renesas Electronics Malaysia Sdn Bhd Unit 906 Block B Menara Amcorp Amcorp Trade Centre No 18 JIn Persiaran Barat 46050 Petaling Jaya Selangor Darul Ehsan Malaysia Tel 60 3 7955 9390 Fax 60 3 7955 9510 Renesas Electronics Korea Co Ltd 1F Samik Lavied or Bldg 720 2 Yeoksam Dong Kangnam Ku Seoul 135 080 Korea Tel 82 2 558 3737 Fax 82 2 558 5141 If the requirements shown in the CAUTION Renesas Tools Website _http Awww renesas com tools G AUTION sentences are ignored the equipment may cause All trademarks and registered trademarks are the property personal injury or damage to the products of their respective owners 2010 Renesas Electronics Corporation and Renesas Solutions Corp
6. application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability
7. e with applicable laws and regulations 11 This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics 12 Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics CENESAS SALES OFFICES Renesas Electronics Corporation http www renesas com Refer to http www renesas com for the latest and detailed information Renesas Electronics America Inc 2880 Scott Boulevard Santa Clara CA 95050 2554 U S A Tel 1 408 588 6000 Fax 1 408 588 6130 Renesas Electronics Canada Limited 101 Nicholson Road Newmarket Ontario L3Y 9C3 Canada Tel 1 905 898 5441 Fax 1 905 898 3220 Renesas Electronics Europe Limited Dukes Meadow Millboard Road Bourne End Buckinghamshire SL8 5FH U K Tel 44 1628 585 100 Fax 44 1628 585 900 Renesas Electronics Europe GmbH Arcadiastrasse 10 40472 Dusseldorf Germany Tel 49 211 65030 Fax 49 211 6503 1327 Renesas Electronics China Co Ltd 7th Floor Quantum Plaza No 27 ZhiChunLu Haidian District Beijing
8. ecautions This product is only intended for use in a laboratory environment under ambient temperature and humidity conditions A safe separation distance should be used between this and any sensitive equipment Its use outside the laboratory classroom study area or similar such area invalidates conformity with the protection requirements of the Electromagnetic Compatibility Directive and could lead to prosecution The product generates uses and can radiate radio frequency energy and may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off or on you are encouraged to try to correct the interference by one or more of the following measures e ensure attached cables do not lie across the equipment reorient the receiving antenna e increase the distance between the equipment and the receiver connect the equipment into an outlet on a circuit different from that which the receiver is connected power down the equipment when not in use e consult the dealer or an experienced radio TV technician for help NOTE It is recommended that wherever possible shielded interface cables are used The product is potentially susceptible to certain EMC phenomena To mitigate against them it is recommended that the following measur
9. es be undertaken e The user is advised that mobile phones should not be used within 10m of the product when in use e The user is advised to take ESD precautions when handling the equipment This product does not represent an ideal reference design for an end product and does not fulfill the regulatory standards for an end product R20UT0217EJ0100 Rev 1 00 Page 6 Dec 16 2010 RENESAS ROE5562N8PFK10 User s Manual Regulatory Compliance Notices European Union regulatory notices This product complies with the following EU Directive This directive is only valid in the European Union Environmental Compliance and Certifications Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment RoHs Directive 2002 95 EC Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC WEEE Marking Notice European Union Only Renesas development tools and products are directly covered by the European Union s Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC As a result this equipment including all accessories must not be disposed of as household waste but through your locally recognized recycling or disposal schemes As part of our commitment to environmental responsibility Renesas also offers to take back the equipment and has implemented a Tools Product Recycling Program for customers in Europe This allows you to return equipment to Renesas for disposal through o
10. luded with the YQPACK100SD for fixing the YQPACK100SD Do NOT use the screwdriver included with the NQPACK100SD ND for fixing the YQ GUIDE S1 That is used only for the HQPACK100SD Note that you need to provide pla aia screwdriver PLQP0100KB A pad pattern 3 Connect the ROE5562N8PFK10 after checking for a match lt gt with the position of pin 1 for the YQPACK100SD an 4 Install the connector of the flexible cable from the emulator to the 38 pin connector on the ROE5562N8PFK10 Ceara We piel vo Moe cies pad panemahd Hold the ROE5562N8PFK10 while connecting the cable to ean OL Me COMPO REN ate carrea aoned avoid imposing heavy pressure on the 38 pin connector of the ROES562N8PFK 10 Use a flat bladed 5 fA screwdriver Q GUIDE S1 x 4 HQPACK100SD not included YQPACK100SD Vv gt J NQPACK100SD ND lt i 1 100 pin 0 5 mm pitch 5 2 For on board evaluation 5 Mount an MCU with on chip flash memory and the HQPACK100SD not included in order on the NQPACK100SD ND on the user system Before using the ROE5562N8PFK10 be sure to read section 7 Notes on Usage Figure 3 Connection of the User System and the MCU Board A WARNING Always switch OFF the emulator debugging MCU board and user system before connecting or disconnecting the emulator Failure to do so will create a FIRE HAZARD and will damage the emulator debugging MCU board and user system Make sure that
11. ns of the board refer to section 6 R0E5562N8PFK10 Dimensions of the Debugging MCU Board YQPACK100SD Connector to be placed between the debugging from Tokyo Eletech Corporation MCU board and the NQPACK NQPACK100SD ND IC socket for mounting on the user system from Tokyo Eletech Corporation YQ GUIDE S1 Screws for fastening the YQPACK to the from Tokyo Eletech Corporation NQPACK Cautions in handling Cautions when handling the products of Tokyo Eletech Corporation User s Manual English and Japanese 1 for each This manual English Note NQPACK YQPACK YQSOCKET YQ GUIDE HQPACK TQPACK TQSOCKET CSSOCKET CSPLUG W and LSPACK are trademarks of Tokyo Eletech Corporation R20UT0217EJ0100 Rev 1 00 Page 1 Dec 16 2010 RENESAS ROE5562N8PFK10 User s Manual 3 Specifications Table 2 shows the functional specifications of the debugging MCU board Table2 Specifications of the Debugging MCU Board Specification e RX62N and RX621 group MCUs in PLQPO100KB A packages e RSF562N8BDBG ROM 512 Kbytes RAM 96 Kbytes Data flash 32 Kbytes e Power VCC AVCC at 2 7 to 3 6 V is supplied from the user system e The state of power supply can be monitored through the test pins TP1 for VCC and TP2 for GND eThe state of analog power supply can be monitored through the test pin TP3 for VREFH System clock EXTAL e This clock signal at 8 to 14 MHz is supplied from the user sy
12. o be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including b
13. rCENESAS ROE5562N8PFK10 R20UT0217EJ0100 Rev 1 00 Debugging MCU Board for 100 pin 0 5mm pitch LQFP Dec 16 2010 of the RX62N and RX621 Groups 1 Overview This product is for MCUs of the RX62N and RX621 groups in the PLQPO100KB A package User s Manual With the E20 emulator the emulator occupies some user port pins for controlling the emulator and output of trace information These user port pins must be connected with a 38 pin connector installed on the user system With the debugging MCU board however all user port pins are available for the user system 1 In addition you do not need to install a 38 pin connector on the user system Figure shows the configuration of a system that includes the debugging MCU board and an E20 Be sure to read section 7 Notes on Usage before using the debugging MCU board 1 When using the debugging MCU board ROE5562N8PFK10 the D A converter function cannot be used E20 emulator Debugging MCU board this product YQSOCKET USB interface cable SS he for mounting aie N product YQPACK C provided with this Il product NQPACK provided with this product Host computer Figure 1 System Configuration 2 Components of the Debugging MCU Board Table 1 lists the components of the debugging MCU board Check that you have all of the components when you unpack the box Table 1 Components of the Debugging MCU Board Quantity Remarks 1 For the dimensio
14. stem Sub clock XCIN e The clock signal at 32 768 kHz is supplied from the user system Notes 1 When using the debugging MCU board ROE5562N8PFK10 the D A converter function cannot be used Notes 2 Please use it by voltage VCC gt Vpor that doesn t enter the state of power on reset 4 Reset Circuit Figure 2 shows the reset circuit with the level on the RES pin pulled up by a 510 kQ resistor U 38 pin connector CN1 AO MCU IC1 YQSOCKET100SDF CN2 Notes 1 Indicated pin numbers are for pins of the 38 pin connector CN1 2 Indicated pin numbers are for pins of the YQSOCKET100SDF CN2 Figure 2 Reset Circuit on the Debugging MCU Board R20UT0217EJ0100 Rev 1 00 Page 2 Dec 16 2010 RENESAS ROE5562N8PFK10 User s Manual 5 Connection To connect the debugging MCU board and user system follow the procedure below The ROE5562N8PFK 10 can be used for debugging and on board evaluation in common by mounting the NQPACK100SD ND on the user system 1 For debugging paeen Flexible cable T For debugging Mount the NQPACK100SD ND on the user system Feat AL 4 ee ensee Be sure to check that the location of pin 1 is correct Pint OA YaSOCKETi00SpF 2 Fer on board evaluation 2 Install the YQPACK100SD after checking for a match with the position of pin 1 for the NQPACK100SD ND Then use the YQ GUIDE S1 to affix the YQPACK100SD to the NQPACK100SD ND e Do NOT use the screws inc
15. the connectors on both ends of the user system interface cable are facing the right way relative to the user side connector on the emulator and the 38 pin connector on the debugging MCU board respectively Incorrect connection will create a FIRE HAZARD and will damage the emulator debugging MCU board and user system A CAUTION Check the locations of pin 1 before mounting the NQPACK The tightening torque must be no greater than 0 054 Nem If the applied torque is not accurately measurable stop tightening when the force required to turn the screw YQ GUIDE S1 becomes significantly greater than that required at the start of tightening Tightening a screw too much may break the screw hole of the NQPACK or lead to a faulty connection by cracking solder on the NQPACK side Failure of conduction during operation may be due to a crack in the solder for the NQPACK Check conduction with a tester and re solder the NQPACK as required R20UT0217EJ0100 Rev 1 00 Page 3 Dec 16 2010 RENESAS ROE5562N8PFK10 User s Manual 6 Dimensions of the Debugging MCU Board Figures 4 shows the dimensions and reference pad pattern of the debugging MCU board ROE5562N8PFK 10 O22 40 00 TP3 TP1 N N I POWER N VREFH VCC D RENESAS amp m gt lS v A aj S E fo oO Pa oO S amp ie Simm mal oO _L Ln a oO CO nn a Le CERES Saree TN M 4725 0 50 x 24 12 00 m p ng 9 25 o E a Co
16. ur approved Producer Compliance Scheme To register for the program click here http www renesas com weee 8 Warranty 1 The warranty of your product is valid for one year after purchase If your product becomes faulty or damaged while being used under good conditions by observing this user s manual we will repair or replace your faulty or damaged product free of charge Note however that if your product s fault or damage is raised by any one of the following causes the warranty is void a Misuse abuse or use under extraordinary conditions b Improper handling such as dropping your product during transportation or carriage c Other connected equipments d Fires earthquakes lightning flood and other unexpected disasters damages and abnormal voltage e Unauthorized remodeling repair adjustment and so on In the above cases contact your local distributor If your product is being leased consult the leasing company or the owner R20UT0217EJ0100 Rev 1 00 Page 7 Dec 16 2010 RENESAS Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information t
17. ut not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an
Download Pdf Manuals
Related Search