Home

User`s Manual ATX Solution Series Computer Enclosures KS 382

image

Contents

1. CEC The High Performance Upgrade Company User s Manual ATX Solution Series Computer Enclosures KS 382 Mini Tower Case This manual is intended only as a guide for Antec s Computer Enclosures For more comprehensive instructions please refer to the user s manuals which come with your components and drives Disclaimer This manual is intended only as a guide for Antec s Computer Enclosures For more comprehensive instructions please refer to the user s manuals which come with your components and drives Basics 1 Take the case out of the box 2 Remove the Styrofoam 3 Remove the plastic bag 4 Place the case upright with the power supply fan at the back facing you ona stable flat surface Remove the two thumb screws which fasten the top cover onto the case These are the only screws you need to remove to open the case Keep these screws separate from the other screws 6 Grip both sides of the top panel with your hands Slide and lift it up 7 From the top of the case right in front of the power supply there is a tab on top of each side panels Lift and pull the side panels out Note Do not use the tab as a handle to lift the case 8 Inside the case you should see the power supply some wiring LED s etc an installed I O panel a power cord and a plastic bag containing more hardware screws brass standoff plastic stands etc oa Motherboard Installation This manual is not designed to co
2. tel 31 10 462 2060 fax 31 10 437 1752 mail antec europe nl Technical Support 1 800 222 6832 or 1 800 22ANTEC www antec inc com 2000 Antec Inc Reproduction in whole or in part without written permission is prohibited All rights reserved Printed in China
3. anty period enclose the proof of purchase with the defective product and return it to the dealer During the warranty period your product will be repaired or replaced without charge excluding shipping and handling To return your product for service package the product securely in its original packaging and ship it postpaid Your dealer or Antec will not be responsible for the damage due to shipping Remember to enclose your proof of purchase and a clear description of the problem IX For Out of Warranty Service If the repair is required after the warranty period there will be a charge for service and parts Contact Antec Inc at 510 770 1200 ext 330 for a repair estimate on your out of warranty product X How To Call For Technical Support At Antec If you need help installing or troubleshooting a product call our Technical Support Voice Message System at 1 800 22 Antec 1 800 222 6832 Because Antec Inc wants to provide the convenient and comprehensive technical support our customers deserve our policy is to return your call within one hour if you call during our office hours Monday through Friday 8 30 a m to 5 00 p m Pacific Time The customer service line is open 24 hours a day every day Messages left after office hours will be returned as soon as possible Antec Inc 47900 Fremont Blvd Fremont CA 94538 tel 510 770 1200 fax 510 770 1288 Antec Europe B V Sydneystraat 108 112 3047 BP Rotterdam The Netherlands
4. hrough any corner will work find the one that s best for you Connect the 4 pin male connector to a 4 pin female connector coming out from the power supply Rear Fan 1 2 Line up the screw holes of the fan to the screw holes on the back of the case that surround the fan grill Holding the fan in one hand insert the screw from the outside into the case fan screw holes Connect the 4 pin male connector to a 4 pin female connector coming out from the power supply Antec Quality 3 year Warranty AIP Antec Inc warrants this product to be free from defects resulting from faulty manufacture of faulty components under the following terms I Warranty Length Parts and labor are warranted for three 3 years from the date of purchase Replacement products will be warranted for the remainder of the warranty period or thirty days whichever is longer Il Who Is Protected This warranty is enforceable only by the original consumer purchaser lll What Is And Is Not Covered It is important to note that our warranty is not an unconditional guarantee for the 3 year length of the warranty Antec Products are made from the finest materials avail able under our exacting manufacturing standards But like any other product it is not indestructible Therefore our warranty does not cover product damage that may result from abuse or mishandling of the products nor does it cover incidental or consequential damage Also as with any pr
5. lusion Of Damages Antec s sole obligation and liability under this warranty is limited to the repair or replacement of a defective product at our option Antec shall not in any event be liable to the purchaser or any third party for any incidental or consequential damage including but not limited to damages resulting from interruption of service and loss of business or liability in tort relating to this product or resulting from its use or possession V Limitations Of Implied Warranties There are no other oral or written warranties expressed or implied including but not limited to those of merchantability or fitness for a particular purpose The duration of implied warranties is limited to the warranty length specified in Paragraph I VI State Law And Your Warranty This warranty gives you specific legal rights You may also have other rights granted under state law These rights vary from state to state Vil Warranty Registration It is not necessary to send anything to Antec Inc to register your products In the event that warranty service is required Antec Inc will request proof of purchase store receipt or invoice VIII For Warranty Service If the products need repair return them to the dealer from whom you purchased the product All products returned to Antec for warranty service must have prior approval which your dealer can obtain by calling Antec Inc at 510 770 1200 If the repair is required within the warr
6. oduct it should be expected that component parts moving parts wheels etc will show wear with use over time and eventually may need to be refurbished or replaced This type of normal wear and tear is naturally not covered by our warranty but we will always be happy to provide you with prompt high quality repair service at a nominal cost All Antec products are covered by this 3 year warranty except keyboards monitors and any product purchased before the inception of this warranty program which is November 1 2000 The following are not covered by the warranty 1 Any product on which the serial number has been defaced modified or removed Damage deterioration or malfunction resulting from a Accident abuse misuse neglect fire water lightning or other acts of nature commercial or industrial use unauthorized product modification or failure to follow instructions included with the product b Repair or attempted repair by anyone not authorized by Antec Inc c Any shipment damages claims must be made with the carrier d Any other causes which does not relate to a product defect Cartons cases batteries cabinets tapes or accessories used with this product Antec Inc does not warrant that this product will meet your requirements It is your responsibility to determine the suitability of this product for your purpose Removal or installation charges Shipping charges Any incidental charges PO pono IV Exc
7. same procedure for other devices Connect a 4 pin large white connector from the power supply to the male 4 pin connector on each of the devices akon IDE Cable Connection This is for IDE devices only 1 After you have connected the devices to the power supply you need to connect the IDE cables between the devices and the motherboard 2 For hard drives and CD ROMs use the 40 pin IDE ribbon cables For floppy drives use the 34 pin ribbon cables These should come with your devices and have a red strip on side When you connect a ribbon cable to a device make sure that the red strip is toward the power connector 3 The side that attaches to devices should be the side that has 2 connectors This will enable you to connect another device if you wish 4 Connect the far end of the cable to your motherboard on the IDE port either IDE 1 or IDE 2 Fan Installation The KS 382 case has two optional fans that can be installed 80mm fan in front and 60mm fan at the rear Note Antec Cooling Fans blow in the direction of the side the Antec logo Front Fan 1 Squeeze the sides of the fan cage near the speaker to release pressure on the tabs Once loose you should then be able to pull the cage back and out of the case Drop the fan into the cage and push it in until it clips in No screws are needed Reattach the cage fan assembly to the case paying attention to the wires of the fan There are slots near each corner to put the wires t
8. ts to your motherboard at the RST connector The label should be facing the front of the case and for all of the following connectors as well 2 Power LED labeled POWER LED connector is located behind the Reset connector 3 Power Switch labeled POWER SW connects to the PWR connector on the motherboard 4 Speaker labeled SPEAKER connector is behind the PWR connector 5 Hard Drive LED labeled HDD LED connects to the IDE or HDD connector 3 5 Device Installation 1 Slide your 3 5 floppy drive into the top drive bay from the back to the front until it stops Make sure the disk eject button of the drive is firmly seated against the eject button of the case 2 With one of your hands holding the drive fasten the floppy drive with the screws provided onto the case 3 Find a small 4 pin white connector on the power supply and connect it into the male 4 pin connector on the floppy drive 4 Install your other 3 5 devices to the drive bays accordingly 5 Connect a 4 pin large white connector from the power supply to the male 4 pin connector on each of the devices 5 25 Device Installation 1 Looking from the rear of the case you can see some metal grills Carefully use a screw driver through the metal grill and gently push the plastic drive bay outwards until it comes off Use your hands to twist the metal plate back and forth until it breaks off Fasten your 5 25 device into the drive bay with screws provided Repeat the
9. ver CPU or RAM or expansion card installa tion Please consult your motherboard manual for specific mounting instructions and trouble shooting 1 Lay the case down so that the open side is up You should be able to see the drive cage and power supply 2 Make sure you have the appropriate I O panel for your mother board If the panel provided is not suitable for your motherboard you may order different styles from Antec directly Please visit www antec inc com under Service and Support and then I O panels which will show you the available I O configurations 3 Line up motherboard with standoff holes and determine which ones line up and remember where they are Note Not all motherboards will match with all of the provided screw holes and this is not necessary for proper functionality In other words there will likely be extra holes 4 Lift up and remove your motherboard 5 Screw in the brass standoffs to the threaded holes that line up with your motherboard 6 Place your motherboard on the brass standoffs 7 Screw in your motherboard to the standoffs with the provided metallic Phillips head screws 8 Your motherboard is now installed into the case Power Connections ATX power supplies have a single 20 pin single large power connector to the motherboard This is set up as a double row of 10 pins 1 Connect the 20 pin ATX power connector to your motherboard ra s and Front Panel Leads Reset labeled RESET SW connec

Download Pdf Manuals

image

Related Search

Related Contents

Copyright © All rights reserved.
Failed to retrieve file