Home

The copyright and all publication rights for this manual

1. Conduct the treatment with starting the intensity value from zero and increasing it slowly If you don t start the machine from zero the error message appears and the output is not generated You can not use the two type of handpieces LF HF at the same time You should choose one of them according to the treatment purpose When the error message appears you should stop the machine immediately and check it out The treatment stimulation should be to the extent of what a patient doesn t feel uncomfortable Avoid the excessive stimulation The electrodes of the handpiece should be contacted to the skin only under the STANDBY state If they are contacted to the skin in the RUN state spark may be generated and then burn may take place 29 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Chapter6 Specifications of Equipment and Items to Be Written 1 Specification of Equipment 1 1 Electrical Specification 1 Rated Voltage and Consumption Power 100 240VAC 10 50 60Hz Less than 240VA 2 Output Voltage 48V 11A MAX 3 LF A Intensity 0 100 1 step PULSE Max RMS 16V 25 30mA_ at 500Q load PULSE Max RMS 16V 25 30mA at 500Q load Mode PULSE 0 5KHz 10OKHz PULSE 0 5KHz 10KHz Time Imin 2min 1 min step D Frequency PULSE Active Rest 50uS 1 000uS S0uS step PULSE Active Rest gt 50uS 1 00
2. Do not make anybody contact the machine except the patient and the doctor VII Be careful not to conduct the energy stimulation into another person VIUI Be careful not to install the power cord of another machine at the same time It can cause the performance degradation of the equipment IX Make sure to use the handpiece electrodes always after cleaning to prevent foreign substances X Do not pull the cord of the main body by force It can cause the performance degradation of and the trouble with the machine 2 4 Cautions after Use I After use put the control knob and switches back to the original position and turn off the power II Be careful not to give an excessive force to the connecting part of cords when you pull out the cords II Make sure to turn off the power and separate the power cord 14 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 5 Cautions in Storage I Do not keep the equipment in a place where there is some slope shaking or possible impact It can cause the performance degradation of the machine or the fire and electric shock II Do not keep the equipment in a place where chemicals are stored or some gas is generated IHI Do not keep the equipment in a place where temperature air pressure humidity ventilation sunlight and air containing dust salt and sulfur have a harmful influence on it IV Keep the equipment in a place far from water 2 6 Ca
3. N Hi 1 _ Excellent synergy effect ns LF RF Cooling Heating amp Cryo Electrophoration 7 i I Ex o ol ut Tolak OT a aes sthetic tre atm ent The copyright and all publication rights for this manual are owned by ILOODA Co Ltd Lunar N Cooling Heating amp Cryo Electrophoration User Manual Any part of this user manual must not be modified reproduced or copied without prior permission of ILOODA Co Ltd Hereafter referred to as ILOODA ILOODA has the right to alter the technical specifications and or configuration of the apparatus to enhance its performance reliability or production capability in our discretion without any prior notification Exemptions The information provided by ILOODA is correct and reliable However ILOODA doesn t take any responsibility for the damage caused by using the equipment for different purposes other than original ones presented in this user manual ILOODA Co Ltd Manufacturing Company Address Rm801 Rm 805 Venture Valley 958 Gosaek Dong Gwonseon Gu Suwon City Gyeonggi Do Korea Tel 82 31 278 4660 Fax 82 31 278 4661 Website www ilooda ccom E Mail sales ilooda com Please check the related local regulations before using the equipment The use of the apparatus may not be permitted if it is not conformity with the related local law 2 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Table o
4. Volume Switch to clockwise direction It will change Output Box from STANDBY to RUN state NORA RUN 6 From RUN state turning the B Volume Switch slowly to clockwise will increase INTENSITY value lower left side of screen and is ready to treat the person Now turning the Volume Switch to counter clockwise will decrease INTENSITY value When the switch is turned completely to the counter clockwise then Output Box changes from RUN to STANDBY state INTENSITY Intensity of impulse Setup Range 0 100 adjustable by 1 unit 25 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 26 32 7 To store current setting value touch SAVE in Save Box at the right side of screen and select OK from the following popup window It will save current setting value to corresponding number Do you want save Just touch the corresponding number to call currently stored value 8 FREQUENCY at the lower side of Output Adjustment Area automatically calculates and displays the setup output energy It cannot be adjusted by user 9 To turn off the equipment after treatment is completed turn the switch from RUN to STANDBY state and turn off the power switch at the back of main body ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 3 Screen Menu Instruction HF 3 1 Power ON OFF and Menu Description All operation module
5. the deformation of the main body the failure in the system and the fire Make this machine used only a professionally trained person Conduct a prior check on the manipulation of the system Check the switches etc and then confirm the correct operation Connect all the cords accurately not to break away easily When you use the equipment after a long interval confirm if it operates normally and safely or not Never disassemble or change the equipment by anybody except by an installation and repair technician It can cause fire or electric shock ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 3 Cautions during Use I Remove all the interruptions around the equipment when it is used Do not put papers or other materials on the top of the machine and block the vent II When the failure in the system takes place stop using it and turn off the power and then contact our customer service center Ill In case of a power outage turn off the power immediately and put the controlling knob and switches back to the original position IV Do not use the equipment near a patient monitor V Always check if there are some abnormalities on the patient and the equipment during use If some abnormalities occur on the patient or the equipment check the patient s safety and stop the equipment When you confirm that the patient and the equipment have no problems after check up continue to use it again VI
6. water Using other liquid for refill can be cause of malfunction 21 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 22 32 1 3 Equipment use procedure 1 Connect power cord to the back of main body 2 Connect electric pad to the side of main body 3 Turn on the power switch at the back of the main body 4 Set output value 5 Tightly adhere the electric pad and wait for treatment when using LF Hand piece 6 Slowly turn the main body s volume knob to clockwise direction for treatment ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Make sure to install and use the parts and accessories after checking their specifications and do not use the different discretionary products from the accessories provided Remove debris on the electrode pads and hand piece and manage them clean Make sure to have the skin contacting the ground Pad and handpiece electrodes cleaned and in case of wound and allergic skin make sure to have the treatment after consultation with a doctor Electrode pads must be in contact with skin perfectly and the space between the skin and the electrode pads to prevent the occurrence of space If there is space the power can be lower and skin can be burnt Check the complete connection of the accessories before turning on the power switch Make sure to start the stimulation output from zero and r
7. 0uS 50uS step 4 HF A Intensity 0 100 1 step 0 5S Max RMS 50V 25 90mA at 500Q load IS Max RMS 50V 25 90mA_ at 500Q load CW Max RMS 50V 25 90mA at 500Q load B Mode 0 5S 1S CW Time 1min 20min 1min step D Frequency 0 58 1S CW IMHz 30 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 31 32 5 COLD HOT A Level OFF COLD HOT under the 22 C in room temperature COLD 20 20 C HOT 37 43 C 6 Protection 1 Common Fact Protection circuit is operated when power voltage and electric current are beyond limit 2 RF Part When you turn on the power after turning off the power the output starts from the initializing value 0 If the volume knob is positioned in the middle the machine cannot be operated 1 2 Mechanical Specification 1 Dimension 375mm x 400mm x140mm WxDxH 2 Weight 13 3kg ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 Items to Be Written 1 Product Name Class II Mixing Stimulator for Medical Use A16270 01 Model Name Lunar N 2 Name of Manufacturer ILOODA Co Ltd Address 801 805 Venture Valley 958 Gosaek Dong Gwonseon Gu Suwon City Gyeonggi Do Korea 3 Manufacture Permission Number No 2461 Article Permission Number 4 Using Purpose Alleviation of Muscle Pains 5 Manufacture Number Date of Manufacture Written on the top of th
8. Manufacture Serial Number Date of Manufacture 2 Items Provided The components Accessories consisting of this equipment are as follows Main Body RF Handpiece and LF Handpiece Power Cable Ground Pad amp Cable User Manual Cart 5 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 3 Howto Use This User Manual Purpose of This User Manual The purpose of this manual is to make users be fully aware of the structure installation manipulation operation and maintenance of Lunar N System Keeping of This User Manual This manual must be kept together with the equipment or near the equipment so as that you can refer to it if necessary amp Expressions Used in This User Manual The expressions Caution Note and Warning as below are used in this manual Caution This expression provides the important information to pay attention to in using the equipment Note Note warns the user about the possible problems related with the improper use of the equipment These problems include the damage to other related property as well as the poor operation of the system This expression involves the matters to take a full note to avoid this harm Warning Warning warns the user about the possibility of improper use of the system and of injury death or serious side effects Please check the related local regulations before using the equipment The use o
9. The following instructions are the essential guidelines to be surely considered before using the equipment If you don t conform to the following instructions the unexpected critical damage like performance degradation of the equipment may be brought about 3 1 Installation of Equipment The equipment must be installed and used only in a hospital or a place where the stimulator related treatment is permitted The use of the equipment in a place 1 e private home etc where is not qualified for treatment by stimulators is strictly prohibited The equipment should be moved and installed only in a state of turning off and placed in a safety flat space The power and system specifications must be checked in installing the equipment and the installation section in this manual should be referred to for a correct installation in installing the electrode pad or other accessories Avoid conductive metallic chairs for patients and doctors or treatment tables and must use non conductive fabric or mat treatment table 3 2 Patient and Cautions Make sure to give the treatment only to the patient in accordance with the purpose of this equipment after the doctor s prior diagnosis The treatment to the patient with other lesion not with the originally targeted one without the doctor s prior diagnosis 1s strictly prohibited Before treatment make sure to check the patient s skin state and sterilize the region to be treated so as that there are no f
10. age this manual and all other related materials always in a good condition and keep them in a place where the stimulating equipment is installed to use them at any time Make the stimulating equipment operated maintained and repaired only by a qualified and authorized person Do not remove or erase the safety cautions and warning message attached to the stimulating system Do not give a shock to the equipment Keep the main body of the equipment the handpieces the connector and the holders in a clean state that has no foreign substances 12 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 13 32 II II IV VI VII VII IX XI XII XII XIV 2 2 Cautions before Use Make sure to read the instructions and use the equipment before using it Make sure to use the equipment on a doctor s prescription Connect the power on with a wet hand Be careful not to spill water into the main body It can cause the damage to the equipment and the fire and electric shock Do not install the equipment in a watery humid place It can cause the damage to the equipment and the fire and electric shock Install the equipment at least a 100m distance from the wall Be careful not to make the power cord pressed by heavy weights or touched by sharp materials The use of a damaged cord can cause fire or electric shock Never use the equipment near flammables It can cause
11. aise it gradually observing the patient s state Do not use water or other liquid solvents in cleaning the electrical parts Prevent to drop water or other liquid on to the system Check if there is moist on the skin when using the ground plate rod Make them contacted after removing moist Conduct the treatment after removing the metals causing an unintended influence on the electrode during treatment Install with care not to fall down on electric wires and pipes or to entwine electric wires Check the damage to the external appearance and electric wires of the equipment on a regular basis Avoid conductive metallic chairs for patients and doctors or treatment tables and must use non conductive fabric or mat treatment table 23 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 Screen Menu Instruction LF 1 1 Power ON OFF and Menu using instruction All operation module and display screen appears at the front LCD monitor A This is touch screen SO operation can be done by touching the screen 1 Connect power cable and accessory and turn on power switch 2 Following main screen appears around 2 3 seconds after power on 2 Output Adjustment Area s 3 Jr CUNAR TN OY 3 Hand piece Setup Box 1 kHz INTENSITY TEMP LEVEL TIME MODE ACTIVE Parameter Menu Box 3 Select Hand piece type from 3 Hand piece Setup Box at the left side o
12. e manual Sp Apparatus verification Data 6 Weight and Packing Unit 1 Weight 13 3kg Main body 2 Packing Unit 1 Set 7 Performance and Using Method Refer to the Manual 8 Cautions in Use Refer to the Manual 9 Rated Power and Voltage 1 Electrical Rated 100 240VAC 50 60Hz 2 Consumption Power Less than 240VA 3 Protection Type and Degree against Electrical Shock Class I Device BF type Device 10 Attachment of Items to be written Back Side of the Main Body 11 This product is medical apparatus 32 32 ILOODA CO LTD
13. ed by others when it is not used or even an operator doctor leaves for a moment Never remove the cover of the equipment The cover of the equipment can be removed only by an authorized repair person of the manufacturer It is impossible for the equipment to conduct the RF treatment in a situation when the equipment cover or protection panel is removed Do not disassemble the equipment Only the manufacturer s official mechanic may disassemble it The operating of high frequency is not allowed in disassembled state 10 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Chapter 3 1 11 32 Safety Cautions Cautions for Environmental Safety 1 1 Electrical Hazard All the users of the equipment should read and observe the following cautions for electrical safety Or electric shocks may take place Do not touch any parts carelessly except the controls of the system Turn off the system or remove the plug when executing the ordinary jobs like connecting the ground plate or ground rod to the equipment Make sure to use the stimulating system only in a place where there is electric installation obeying the standards and regulations of each region Do not use water or other liquid solvents when cleaning electrical parts Prevent water or other liquid from spilling it on the system Install with care not to fall down on electric wires and pipes or to entwine electric w
14. f Contents Chapter 1 Overview l Apparatus verification Data 2 Items Provided5 3 Howto Use This User Manual Chapter 2 Introduction to Lunar N 1 Introduction to Lunar N 2 Qualification for Using Lunar N 3 Essentials for Using Equipment 3 1 Installation of Equipment 3 2 Patient and Cautions 3 3 Setting of Equipment Chapter3 Safety Cautions 1 Cautions for Environmental Safety 1 1 Electrical Hazard 1 2 Fire Hazard 2 Cautions for Safe Use of Equipment 2 1 Cautions for Product Safety 2 2 Cautions before Use 2 3 Cautions during Use 2 4 Cautions after Use 2 5 Cautions in Storage 2 6 Cautions for Maintenance Chapter4 Structure of Equipment 1 Description of Equipment 1 1 External Appearance Chapter5 Use of Equipment 1 Installation and Use of Equipment 1 1 Installation of Main Body 1 2 Installation of Accessories 1 3 Summing up of Using Process 3 32 ILOODA CO LTD User Manual Lunar N Cooling Heating amp Cryo Electrophoration 2 Use of Screen Menu 2 1 Use of Power On Off and Menu 2 Error Message Chapter6 Specifications of Equipment and Items to Be Written 1 Specification of Equipment 1 1 Electrical Specification 1 2 Mechanical Specification 2 Items to Be Written 4 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Chapter 1 Overview 1 Apparatus verification Data Product Name Mixing Stimulator for Medical Use Model Name Lunar N
15. f screen LF Low Frequency Hand piece HF High Frequency Hand piece 4 Set output value by touching each menu at Q Parameter Menu Box When pressing the menu to setup then corresponding menu value appears to Output Adjustment Area at the center of screen Adjust the value to desired value by touching the arrows UP DOWN button at each side TIME Treatment time setup Setup Range 1 minute 20 minute adjustable by 1 minute unit 24 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual MODE Impulse mode setup Setup Range PULSE PULSE ACTIVE Energy irradiation time to skin per one impulse cycle Setup Range 50us 1000us adjustable by 50us REST Energy resting time to skin per one impulse cycle Setup Range 50us 1000us adjustable by 50 unit TEMP LEVEL Temperature adjustment Output Adjustment Area changes to following display for temperature setup and adjust temperature by touching UP DOWN Each of COLD HOT area is displayed in blue red gauge The gauge bar becomes full when each temperature stage is reached 1 2 3 HOT Stage 1 3 Stage 1 under 37 C Stage 2 between 38 T 42 C Stage 3 above 43 C a ee COLD Stage 1 4 E Stage 1 above 11 C Stage 2 between 10 1C Stage 3 between 0 9 C Stage 4 between 10 20 5 After setup is completed tightly adhere the electric pad and Hand piece electrode to skin and turn the B
16. f the apparatus may not be permitted if it is not conformity with the related local law 6 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Chapter 2 Lunar N Introduction 1 Lunar N Introduction Lunar N is Total Skincare equipment that combines Electro stimulation and Cooling Heating It is a skin treatment equipment using Cryoelectrophoresis which extends the small skin holes that molecules cannot move using electro stimulation and enables the medicine to reach up to subcutaneous fat layer You can expect more than 2 times of medicine penetration effect than current Iontophoretic penetration rate 50 60 In addition it has strong cooling system that enables High Frequency RF energy penetration up to dermis layer without pain and promotes induces collagen generation by heating the dermis layer to provide elasticity to the skin Lunar N restores tired and loose skin by various pollution and stress back to healthy and elastic skin using two types of skin treatment Electro stimulation LF RF Skin elasticity effect Lifting by u Current Alkaline reaction Sebum and keratin degradation Soften skin and tissue Acid reaction Enhance elasticity enforce protection by hardening effect of weak acid Joule Heat Activate collagen Cooling Strong soothing effect for tired skin by summer UV and heat Pore astringent effect Astringent Efficiently removes swelling at eye rims or cheek wit
17. h cold inflammation edema reduction effect Excellent moisturizing effect by synergy with face lotion Cryo electrophoresis Efficient skin penetration of nutrition elements Nutrient Strong Cryoelectrophoresis cool down the skin surface to prevent skin burn and to maximize medicine penetration effect Existing Electrophoresis has 30 of penetration rate while Lunar N can penetrate 50 60 without skin damage 7 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 8 32 Qualification for Using Lunar N It is strictly required that this equipment be used only by the person qualified for safety handling and use of mixing stimulators Thus the people who don t have a stimulator related license or training certificate must not use this equipment It is recommended that all the relevant people Nurse etc including medical staffs complete the training on installation procedure and operating method of stimulators potential hazards and interactions of tissues and take the respective safety education program according to each country s regulation in addition to stimulator related safety education It is also recommended that the person wanting to use the stimulator obtain an approval required for using it from the relevant authorizing organization in the country ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 3 Essentials for Using Equipment
18. ide of screen and select OK from the following popup window It will save current setting value to corresponding number Just touch the corresponding number to call currently stored value PULSE at the Parameter Menu Box displays the High Frequency output count It cannot be adjusted by user To turn off the equipment after treatment is completed turn the switch from RUN to STANDBY state and turn off the power switch at the back of main body ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 1 Error Message The error message is a warning or notifying pop up message appearing during use or operation If you encounter the following message stop the treatment immediately check the content of the message and then readjust the equipment Screen of Error Message Message The error message as the left side pops up and the lero Sta rt message in the box varies with the content of the error Refer to the following table for the contents of the errors Turn the volume switch to the left and then start it Zero start The volume switch is not set on Zero 0 from zero 0 Time Out The setting time is over Reset the time or finish the operation Temperature sensor is unlinked or Contact the retailer or the manufacturer Temp Open loosen The temperature inside the machine is Stop operating and turn off the machine Over Temp over 60 C over temperature immediately
19. ion RF Hand piece It is composed of 2 ceramics and this Hand piece is used to transmit High Frequency It can be used without requiring additional electrode plate or pad a HF Ceramic Electrode that transmit High Frequency to human body LF Hand piece It is composed of single ceramic and this Hand piece is used to transmit low frequency It is used with electric pad b BIP Electrode Electrode that transmit low frequency to human body 18 32 ILOODA CO LTD User Manual Lunar N Cooling Heating amp Cryo Electrophoration 1 1 3 Accessories The accessories comprising this equipment are as follow Power Cable Ground pad amp cable In case of using LF handpiece User Manual Cart 19 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Chapter5 Use of Equipment 1 Installation and Use of Equipment 1 1 Installation of Main Body Refer to the images and numbering of Rear Part in 1 1 1 Main Body of Chapter 4 1 Connect the power cord to the power cord connector H at the back side of the main body Check the specification of the power cable and connect it Install the main body in the cart or a flat space so that it cannot move 1 2 Accessory Installation Refer to the images and numbering at the side of Chapter 4 1 1 1 Main Body Description 1 Connect electric pad to the electric pad connec
20. ires Make sure to install and use the proper parts and accessories and do not use the different products from the accessories provided along with the equipment Check the damage to the external appearance and electric wires of the equipment on a regular basis 1 2 Fire Hazard All the users of the equipment should read and observe the following cautions for fire hazard Or fire may take place Do not put the flammable or combustible materials or substances around the treatment room If you use alcohol to clean the handpiece electrodes wait up to the time when it is completely evaporated and dried before operating the system Do not give the energy stimulation to any part except for the part to be treated Avoid the conducting materials like metals that may work in reverse with the energy stimulation and absorb it when giving it Cut off the power immediately in case of fire Only use a CO2 or powder extinguisher in case of fire ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 2 Cautions for Safe Use of Equipment 2 1 Cautions for Product Safety The owner and user of the stimulating system are obliged to obey all of the equipment related safety cautions The following cautions related with the equipment must be observed Use this stimulating system only for the designed purpose Use the equipment only when it operates normally There should not be an error message Man
21. oreign substances Before treatment remind a patient of the cautions before during and after treatment and notify the possibility of occurrence of unintended abnormal symptoms to him or her 3 3 Setting of Equipment Set the parameter values in consideration of the patient s state before setting the equipment The setting of the equipment must be conducted in standby mode and the handpiece should be put in a safety place Handpiece Holder when the equipment is set Increase using amount and intensity gradually from a small value to the desired value when adjusting the setting values 9 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Abide by all the safety related cautions stated in this maual Never adjust the equipment at the user s doctor s discretion with other adjusting method different from the method stated in the manual Do not make the equipment used by a non qualified person without the supervision of a trained and experienced specialist Place the handpiece in a stable location and keep the electrodes in a clean state Patient and operator doctor should not be carried the metallic materials possibly conducting electricity Use the equipment only onto the skin surface in which there are no infection and other damage Never use the equipment for treatment of different purpose other than original purpose Make sure to turn off the equipment not to be operat
22. s and display screen are displayed in LCD monitor A at the front of main body It is touch screen and all operation is performed by touching the screen 1 Connect power cable and accessory and turn the power switch on 2 Following main screen appears around 2 3 second after power on 2 Output Adjustment Area 3 Hand piece Setup Box ENERGY TEMP LEVEL TIME MODE PULSE Parameter Menu Box 3 Select Hand piece type from 3 Hand piece Setup Box at the left side of screen LF Low Frequency Hand piece HF High Frequency Hand Piece 4 Set output values by touching each menu of Q Parameter Menu Box Corresponding menu value appears in the Output Adjustment Area at the center of screen by touching the menu to set Adjust the desired setup value by touching the UP DOWN round arrow type button at both sides TIME Treatment time setup Setup Range 1 minute 20 minute adjustable by 1 minute 27 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 28 32 5 6 7 8 MODE Impulse mode setup Setup Range CW 0 5S 1S TEMP LEVEL Temperature adjustment See LF Instruction After setup is completed tightly adhere the electric pad and Hand piece electrode to skin and turn the B Volume Switch to clockwise direction for treatment See LF Instruction To store current setting value touch SAVE in Save Box at the right s
23. tor F at the side Connect cable to Main Body s electric pad connector after connecting electric pad and electric pad cable LF should be used with electric pad Impulse is not transmitted to body if the electric pad is not used Electric pad should be tightly adhered to skin When electric pad is not tightly adhered to the skin and there is space between pad and skin then the impulse may not be smoothly transmitted HF Hand piece is used alone There is no electric current activity at the electric pad when using HF Hand piece 20 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 1 2 1 Cooling water refilling coupler installation Please refer the description of equipment 1 1 1 1 Insert the cooling water refilling coupler into the cooling water refilling connector IN OUT on the back of the equipment horizontally 2 Put the edge of the coupler hose into the distilled water bottle Connect the cooling water refilling coupler with the main body likewise figure I until you hear the tick sound Disconnect the coupler from the main body with putting the disassembling button the metal part likewise figure II If the cooling water system is working when the coupler connected incompletely it can be the cause of malfunction Cooling water should be located higher than the coupler when you refill the water You must use distilled
24. utions for Maintenance I In case of the trouble with machine make sure to stop using it and contact the store you purchased from or the customer service center II Never open the machine and the controller III Do not give an impact to the main body If there had been some impact on it make sure to use the equipment after check ups 15 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Chapter4 Structure of Equipment 1 Description of Equipment 1 1 External Appearance 1 1 1 Main Body Front Part A LCD Monitor Touch panel conducting all controls of the machine and outputting the monitor B Volume Switch Volume switch adjusting the intensity of energy C Handpiece Holder Cradle keeping handpieces with safety 16 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual Flank Part D BIP Handpiece Connector Connecting part between BIP handpiece and main body E RET Handpiece Connector Connecting part between RET handpiece and main body F Ground pad Connecting part between main body and ground plate in case of using LF handpiece Rear Part G WATER IN connector A coolant inlet part H WATER OUT connector A coolant outlet part I AC INPUT Power code connector and ON OFF switch 17 32 ILOODA CO LTD Lunar N Cooling Heating amp Cryo Electrophoration User Manual 1 1 2 Hand piece descript

The copyright and all publication rights for this manual

Contents

Download Pdf Manuals

Related Search

Related Contents