(SAVE THESE INSTRUCTIONS)
Contents
1. Indication Alarm Condition Flash twice every Beep twice every Utility Failure The UPS is providing power Using 30 seconds 30 seconds to the outlets from its battery Battery l Utility Failure The UPS is providing AEE tapia vend battery power Rapid beeping indicates the seconds every 1 2 second SU unit will run out of power shortly Battery Overload Occurs when connected equipmentexceeds the listed capacity of the Fault Off Constant Tone UPS Turn the UPS off unplug at lease one piece of equipment from the outlets reset the circuit breaker and turn the unit on TECHNICAL SPECIFICATIONS Capacity VA 850 Capacity Watts 490 50 60Hz Auto Sensing Simulated Sine Wave at 230Vac 7 50 60Hz 1 On Utility Circuit Breaker and Internal Current Limiting On Battery Internal Current Limiting Frequency Range On Battery Output Voltage On Battery Output Frequency Overload Protection Surge Protection Lightning Surge Protection Yes Physical Total of UPS outlets 1 Full Time Surge Protection Outlet 2 Battery Backup amp Surge Protected Outlets 84 x 110 x 309 Maximum Dimensions HxWxD mm Weight kg Battery Sealed Maintenance Free Lead Acid Battery Typical Recharge Time Environment Operating Temperature Relative Humidity Communication PowerPanel Personal Edition Software Management Auto Charger Yes Auto Restart Yes USB interface Yes 12V 4 5Ah2. or spray detergent CAUTION Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from batteries CAUTION The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary CAUTION Internal battery voltage is 12Vdc Sealed lead acid 6 cell battery CAUTION When replacing the batteries use the same number and type of batteries CAUTION Do not dispose of batteries in a fire The battery may explode Do not open or mutilate the battery or batteries Released electrolyte is harmful to the skin and eyes CAUTION A battery can present a risk of electric shock and high short circuit current The following precaution should be observed before replacing batteries 1 Remove watches rings or other metal objects 2 Use tools with insulated handles 3 Wear rubber gloves and boots 4 Do not lay tools or metal parts on top of batteries 5 Disconnect charging source prior to connecting or disconnecting batteries terminal INSTALLING YOUR UPS SYSTEM UNPACKING The box should contain the following 1 UPS Unit x 1 2 USB Cable x 1 3 User Manual x 1 4 Management software Disk x 1 OVERVIEW The EX650E EX850E ensures consistent power to your computer system and its included software will automatically save your open files and sh
3. the battery by leaving the Battery not fully charged UPS plugged in Contact CyberPower Systems Battery is worn out Technical Support The battery is worn out Contact CyberPower Systems Technical Support Contact CyberPower Systems Technical Support Connect the USB cable to the UPS unit and an open serial port on the back of the computer You must use the cable that came with the unit The unitis nororovidin Shutdown your computer and turn the ca EGG p g UPS off Wait 10 seconds and turn the y P i UPS back on This should reset the unit For more information visit www cpsww com All rights reserved Reproduction without permission is prohibited CEZ A The UPS does not perform expected runtime The UPS will not turn on Mechanical problem The USB cable is not connected PowerPanel Personal Edition is inactive
4. x1 12V 7Ah x1 8 hours 0 C to 40 C 0 to 90 Non condensing Windows Vista XP 2000 Server 2003 Linux CYBERPOWER GREENPOWER UPS TECHNOLOGY CyberPower s Green Commitment CyberPower is dedicated to the development of green products and has adopted Green practices throughout its business including membership in Climate Savers Computing Initiative CSCI accordance with the Restriction on Hazardous Substances ROHS Waste Electrical and Electronic Equipment WEEE protocols as well as ISO 14001 and IECQ QC080000 CyberPower pledges to provide the advanced energy solution for the environment and become a leading eco friendly organization in the UPS industry Reduce Energy Cost with GreenPower UPS Technology CyberPower s goal is not only to provide eco friendly products but also to bring the best value for consumers The advanced energy saving design improves the operating_efficiency and eliminates waste energy consumption As a result consumers will enjoy significant energy cost savings with the adoption of GreenPower UPS technology TROUBLESHOOTING Possible Cause Circuit breaker has Problem The outlets stop providing power to equipment Circuit breaker button is projecting from the side of the unit Turn the UPS off and unplug at least tripped due to an one piece of equipment Reset the sucha circuit breaker by depressing the button and then turn the UPS on Recharge
5. CyberPower Reliability Quality Value EX650E EX850E User s Manual K01 COO00xx 00 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate your UPS CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants See the specifications for the acceptable temperature and humidity range CAUTION To reduce the risk of overheating the UPS do not cover the UPS cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces CAUTION Do not attach non computer related items such as medical equipment life support equipment microwave ovens or vacuum cleaners to UPS CAUTION Do not plug the UPS input into its own output CAUTION Do not allow liquids or any foreign object to enter the UPS Do not place beverages or any other liquid containing vessels on or near the unit CAUTION In the event of an emergency press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS CAUTION Do not attach a power strip or surge suppressor to the UPS CAUTION Unplug the UPS prior to cleaning and do not use liquid
6. cle wall outlet Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical demands e g air conditioner refrigerator copier etc Avoid using extension cords 4 Depress the power switch to turn the unit on The power on indicator light will illuminate and the unit will beep 5 If an overload is detected an audible alarm will sound and the unit will emit one long beep To correct this turn the UPS off and unplug at least one piece of equipment from the outlets Wait 10 seconds Make sure the circuit breaker is depressed and then turn the UPS on 6 To maintain optimal battery charge leave the UPS plugged into an AC outlet at all times 7 To store your UPS for an extended period cover it and store with the battery fully charged Recharge the battery every three months to ensure battery life BATTERY REPLACEMENT CAUTION Servicing of battery should be performed or supervised by personnel knowledgeable of batteries and the required precautions CAUTION Turn off the unit and unplug it from the AC power source before servicing the battery BASIC OPERATION DESCRIPTION gt ee ee eee oe See See ee ee S eS ee U L 1 Battery and Surge Protected Outlets The unit has two battery powered and surge protected outlets to ensure temporary uninterrupted operation of your equipment during a power failure 2 Full Time Surge Protection Outle
7. ts The unit has one surge suppression outlet 3 Power On Off Switch To turn the UPS on press the power button for approximately 1 seconds you will hear a constant tone 1 second and release after a short beep To turn the UPS off press the power button for approximately 1 seconds you will hear a constant tone 1 second and release after two short beeps Alarm setting The audible alarm can be turned off or back on by quickly pressing the POWER button twice The default setting is for the Alarm On To turn the alarm off quickly press the power button twice You will hear two short beeps when the alarm is turned off To turn the alarm back on quickly press the power button twice You will hear a single short beep when the alarm is turned on When the alarm is turned off there will be no audible notification when the UPS reaches a low battery state 4 Power On Indicator This LED indicates the status of UPS 5 Input power cord Connect to utility power through the input power cord 6 Input Circuit Breaker The Circuit Breaker provides optimal overload protection 7 USB Port to PC This port allows connection and communication from the USB port on the computer to the UPS unit The UPS communicates its status to the PowerPanel Personal Edition software 8 Communication Protection Ports Communication protection ports will protect any standard modem fax telephone line DEFINITIONS FOR ILLUMINATED LED INDICATORS Status
8. utdown your computer system during a utility power loss HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1 Ensure that the equipment plugged into the battery power supplied surge outlets does not exceed the UPS unit s rated capacity 650VA 360W for EX650E 850VA 490W for EX850E If the rated unit capacities are exceeded an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip 2 There are many factors that can affect the amount of power that your computer system will require For optimal system performance keep the load below 80 of the unit s rated capacity HARDWARE INSTALLATION GUIDE 1 Your new UPS may be used immediately upon receipt However recharging the battery for at least 8 hours is recommended to ensure that the battery s maximum charge capacity is achieved Charge loss may occur during shipping and storage To recharge the battery simply leave the unit plugged into an AC outlet The unit will charge in both the on and off position 2 With the UPS unit off and unplugged connect the computer monitor and any externally powered data storage device Zip drive Jazz drive Tape drive etc into the battery power supplied outlets DO NOT plug a laser printer copier space heater vacuum paper shredder or other large electrical device into the UPS The power demands of these devices will overload and possibly damage the unit 3 Plug the UPS into a 2 pole 3 wire grounded recepta
Download Pdf Manuals
Related Search