Home

User manual Levelsystem Caravan

1. When the system is operating all persons and animals should keep their distance Body parts e g hands and eyes should never come into contact with released fluids Oil leaving the hydraulic levelling system may be under high pressure and could cause serious injuries to the skin Consult a doctor immediately in case of accident The caravan should be parked on a solid non slippery surface The parking location must be free of holes and free of waste and surrounding objects f the caravan is parked on very soft soil you must place a support plate under each jack in order to distribute the weight Check that the installation of the hydraulic levelsystem is performed by a skilled mechanic with sufficient practical experience and technical E amp P Hydraulics training In case of repairs malfunctions to the hydraulic levelsystem know what you are doing Never try to repair it yourself but consult your installer or dealer Fully read this user manual before using the hydraulic levelsystem After deploying the hydraulic levelsystem ALWAYS make an inspection tour around the caravan just to be sure the caravan stands stable all hydraulic jacks are on the ground User manual 3 Control functions 3 1 Functions on the control panel E amp P HYDRAULICS The diagram below shows the appearance of the control panel By using the control panel or remote control see chapter 3 2 you can operate the hydraulic levelsyste
2. arrows on the indicator LED no 14 central on the control panel shows the position of the caravan In the unlikely event that the caravan is already level then the indicator LED no 14 lights up GREEN Further operation goes as described in the chapters 4 1 up to 4 3 5 2 6 Which device takes command The device which is switched on first remote control or control panel takes the command to control the system until that device is switched off If you would like to switch from one control device to another you need to switch off the power from the device that was in operation first REMARK 1 In the event of switching over from the remote control to the control panel you have to wait a little time to give the system enough time to switch off contact between the remote control and the operating system REMARK 2 It may be that the operating system is built in such a way that receiving a signal between the remote control and the operating system works poorly or even not at all caused by caravan construction materials e g steel wood plastics etc In this case there is a possibility to move the antenna away from the operating system by means of an optional extension cable length max 2 meters available from E amp P Hydraulics 5 2 7 Battery Indicator When the battery level indicator LED no 15 lights RED the device does not stop working immediately After this signal it is possible to use the remote control apr another 4 tim
3. this manual in case of failure and or service amp repair matters When this operation for some reason has not been done or has been carried out incorrectly it is not possible to level the caravan with the remote control 5 2 2 Antenna Check if there is an antenna connection on the operating system see picture below If this is not the case the remote control CANNOT communicate with the hydraulic levelling system In principle the antenna connector and the antenna are always present when you purchase the levelsystem including a remote control unit If you purchased the remote control at a later stage i e not with the levelsystem then you should remember that this antenna connection on the operating system main unit could be missing The presence of the antenna is dependent on the age of the levelsystem After January 2013 all operating systems have this antenna connector In this case the dealer installer can directly connect the antenna to the operating system the antenna is supplied with the remote control Below is the picture of the operating system including the antenna connection Operating system with antenna connection built in protective casing Operating system main unit Antenna Antenna connection User manual E amp P HYDRAULICS Remote control continued 9 2 3 Battery Remove the battery cover on the rear side of the remote control by firmly pressing the cover and then sliding out Inse
4. Extensive function declaration LED s 1 SLOPE TOO In this position the caravan cannot be levelled the surface STEEP is not even enough If necessary switch over to manual mode 2 BATTERY The battery is empty or the voltage is too low to be able to LOW VOLTAGE work safely WITHDRAW The caravan is too high at the front withdrawn the front FRONT WHEEL wheel and the LED will go out JACKS NOT fully One or more jacks are extended or not fully retracted cS A 40 V zero point RETRACTED 9 MANUAL Indicates that the caravan can now be brought to the correct MODE level manually LEVEL Indicates that the caravan can now be brought to the correct level m BATTERY 9V The battery voltage of the remote control is too low VOLTAGE only present on the remote control E amp P LOGO Indicates that the levelsystem is switched on only present on the control panel BUTTONS ON OFF owitches the levelsystem on or off MANUAL owitches the levelsystem into manual mode for levelling d MODE the caravan p J AUTOMATIC owitches the levelsystem into automatic mode for levelling UN MODE the caravan RETRACT Automatically retracts all jacks b ALL JACKS 10 JACK LEFT Controls retracting and extending the left jack 11 l JACKS REAR Controls retracting and extending the rear jacks 12 JACKS FRONT Controls retracting and extending the front jacks 13 JACK RIGHT Controls retracting and extending the right jack U
5. REM RE RR RR wm er l i t i l l i T m e mm N e e N UN t lt Hydraulic axle support gt right A I Hydraulic corner support I Hydraulic corner support rear side left rear side right Y a gt gt r PENES EEEE sms LEE UT User manual E amp P HYDRAULICS 7 Remarks and recommendations Below is an overview concerning remarks and recommendations tips for the hydraulic levelsystem After 4 minutes of no operation the system will switch off automatically The automatic levelling cycle can only be started after all jacks have been retracted If the jacks are not retracted when the automatic cycle starts the system will do this automatically So it is not possible to make short adjustments to the jacks the system will always first completely retract its Jacks At a low battery voltage the system will automatically switch off All normal functions of the system are switched off in error mode During winter conditions e g in snow and ice put something e g a piece of carpet under the Jacks to avoid sliding Manual operation is mainly recommended for uneven surfaces The system cannot handle all angles the limit values differ per caravan f the system makes a slope angle that is too big and no longer responds to requests for automatic levelling we recommend bringing the vehicle as close as possible to the zero poi
6. The E amp P Hydraulics levelling system is an electrically hydraulically driven system A hydraulic pump is powered by a 12V direct current motor which will pump hydraulic oil through a system of hydraulic hoses two hydraulic axle supports and four hydraulic corner supports with the aim of stabilizing and levelling the caravan Mounted to this pump are the oil reservoir the valve block and solenoid magnetic valves The E amp P Hydraulics levelsystem is electronically controlled by an operating system or so called main unit which is mounted at a central location in the caravan The levelsystem can be operated either fully automatically or manually by means of a built in control panel and or optional remote control Most frequently the control panel is mounted in the sidewall at the entrance of the caravan The jacks have the weight bearing and levelling capacity your caravan requires Each axle support has a 180 mm foot plate on a flexible pivot guaranteeing the greatest firmness possible on any surface Axle supports 2 pcs Corner supports 4 pcs Control panel O Oo U gt Remote control optional E Protective casing pump housing F Hydraulic pump G Operating system main unit User manual E amp P HYDRAULICS The E amp P Hydraulics levelsystem continued 1 2 Using the hydraulic levelsystem The levelling system is designed to be used for creating a stable and horizontal position for the caravan t
7. User manual E amp P HYDRAULICS Ep HYDRAULICS LEVELSYSTEM HYDRAULIC LEVELSYSTEM CARAVAN 6 supports ENGLISH User manual E amp P HYDRAULICS Copyright 2015 E amp P Hydraulics This manual is copyrighted with all rights reserved Under the copyright laws this may not in whole or in part be copied photocopied reproduced translated or converted to any electronic medium or machine readable from without prior written consent of E amp P Hydraulics Limited Warranty Under all circumstances this manual should be read thoroughly before installing and or using the product In no event shall E amp P Hydraulics be liable for any direct indirect special consequential or incidental damages arising out of the use or inability to use this documentation or product even if advised of the possibility of such damages E amp P Hydraulics reserves the right to change parts of the device at any time without preceding or direct announcement to the client E amp P Hydraulics reserves the right to revise the manual s and to make changes in the contents without obligation to notify any person or entity of the revision or change A registration number appears on the product Make sure that this official registration number has not been removed It should be used whenever servicing by E amp P Hydraulics or an authorized E amp P Hydraulics dealer is necessary Important This equipment has been tested and found to comply with the li
8. e who are responsible for installing our products for you This manual is part of our policy In this manual we explain how to use the general characteristics as easy and efficient as possible Precisely follow these instructions for the installation because installing the E amp P Hydraulics levelsystem is a precise job Fully installing the system requires a high level of skill After all we are dealing with equipment that must be able to withstand huge forces something that is often underrated by people with insufficient technical training If the installation is not performed correctly serious damages could result in a short time and even personal injury Therefore this system may only be installed by professional technicians with sufficient practical experience and a thorough relevant technical training At all times the installer will bear sole responsibility for the assembly of the system This product is based on hundreds of test hours as well as many successful installations If you follow this manual step by step you will see what a wonderful user friendly quality product this is However there will always be aspects that can be improved If you have any suggestions remarks or questions concerning this product or manual please do not hesitate to contact us On behalf of E amp P Hydraulics Eric Klinkenberg amp Pierre Blom User manual E amp P HYDRAULICS 1 The E amp P Hydraulics levelsystem 1 1 Operating of the levelsystem
9. ee deleted removed or made unreadable User manual E amp P HYDRAULICS 11 Notes User manual E amp P Hydraulics NEDERLAND www ep hydraulics nl info ep hydraulics nl telefoon 31 0 252 626 151 E amp P Hydraulics UNITED KINGDOM www ep hydraulics co uk info ep hydraulics co uk phone 44 0 1254 297 785 E amp P Hydraulics NORGE www ep hydraulics no info ep hydraulics no telefon 47 480 783 78 E amp P Hydraulics DEALER E amp P HYDRAULICS E amp P Hydraulics DEUTSCHLAND www ep hydraulics de info ep hydraulics de telefon 49 0 2274 700 397 E amp P Hydraulics FRANCE www ep france com info ep france com telephone 33 0 9 70 40 61 49 E amp P Hydraulics SVERIGE www ep hydraulics se info ep hydraulics se telefon 46 0 705 640 725 Ep HYDRAULICS LEVELSYSTEM www ep hydraulics eu Made in Holland
10. en this operation for some reason has not been done or has been carried out incorrectly it is not possible to level the caravan The zero point is the point level to which the hydraulic leveling system in an automatic cycle returns Start Manual levelling Before automatic levelling can be activated you must set the zero point For setting the zero point you must first perform the manual levelling procedure REMARK Do this by placing a spirit level in the center of the caravan ATTENTION Never put the rear brackets first to the ground This in case creating too much load on the caravan Setting the zero point Step 1 Press 1x on the button ON OFF no 5 to switch OFF the levelsystem after manual levelling Step 2 Press 1x on the button ON OFF no 5 to switch the levelsystem ON Step 3 Press 5x on the button JACKS FRONT no 12 Step 4 Press 5x on the button JACKS REAR no 11 All LED s on the control panel light up the vehicle stands in zero mode Step 5 Press 3x on the button RETRACT ALL JACKS no 8 The zero point is programmed Step 6 Press 1x on the button ON OFF no 5 to switch the levelsystem OFF User manual E amp P HYDRAULICS 9 2 Remote control programming 5 2 1 Introduction The procedure described below has already been carried out at your dealer installer You don t have to perform this procedure by yourself E amp P Hydraulics has decided to include this chapter as an extra in
11. es E amp P HYDRAULICS page 4 page page page page page co N O O C1 page 9 page 10 page 11 page 12 page 13 page 15 page 16 page 1 page 20 page 22 page 23 page 24 page 25 page 26 page 28 User manual E amp P HYDRAULICS Preface With the purchase of the E amp P Hydraulics levelsystem your caravan will be automatically levelled and or put stable placed with one push of a button Never a caravan that moves when you walk through it or if it is windy which you suffer from unwanted opening or closing doors where the shower water runs through to the wrong side caused by height differences wherein you have the problem of sleeping in a lean angle All issues that are fixed with the E amp P Hydraulics levelsystem The ergonomic design ensures effortless handling and the sympathetic good looks will automatically enhance your working environment It is based on proven E amp P Hydraulics technology which forms the basis of all our E amp P Hydraulics products After installation one button operates the entire system Within the E amp P Hydraulics strategic vision this products is 100 user friendly and reliable This philosophy does not only apply to our customers end users Also the technicians installing this device system at the dealers are very important to us This product greatly depends on a proper professional installation That s the reason why E amp P Hydraulics do all they can do to support the peopl
12. es Make sure there is a spare battery in the caravan User manual E amp P HYDRAULICS 5 3 Emergency pump optional 9 3 1 Introduction The optional Emergency hand pump allows the levelsystem to be operated manually in the emergency event the system is defective or more likely because there is not enough battery voltage present This possibility is offered by E amp P Hydraulic for situations where for whatever reason the levelsystem does not withdraw its support jacks and is therefore preventing you from driving or moving the caravan We call it an emergency situation because in practice the time for withdrawing the hydraulic jacks is most often also the time of a planned departure By not automatically withdrawing the support jacks you can no longer move with adverse consequences Therefore E amp P Hydraulics offers you the possibility to integrate an emergency hand pump for the levelsystem As the name implies it is a pump operated by hand that controls the withdrawal of all jacks This means that the time of your departure transport or movement can be guaranteed The emergency hand pump is mounted under the caravan in such a way that it is accessible from the side Protective pump housing with the Emergency hand pump connections to the emergency pump User manual E amp P HYDRAULICS Emergency pump continued 9 3 2 Putting the Emergency pump into use When actually using the emergency hand pump operation pr
13. for any oil leaks Repair or exchange Check cables for loss of voltage e Withdrawn the front wheel IMPORTANT For all other reports and or mal functioning of the system please contact your dealer installer User manual E amp P HYDRAULICS 9 Maintenance The E amp P Hydraulics levelsystem does not have parts that need to be maintained periodically When parts have been taken apart the warranty will become invalid If necessary parts could be substituded repaired and or exchanged warranty Please contact your E amp P Hydraulics dealer installer if necessary WARNING In control service works secure the caravan by placing suitable stands under the caravan By not doing this you create a real danger of personal injury or serious accident Preventative controls Periodically checking the hydraulic oil level ONLY by dealer installer The hydraulic oil type Pentosin CHF 11S preventative replace after apr 36 months Periodically check the electronic cables and connections Periodically check the hydraulic jacks Remove dirt sand mud and other contamination that settles during use it may obstruct the operation of the hydraulic leveling system If the jacks remain extended for a longer period of time the exposed legs should be protected by spraying them with a silicon lubricant to help prevent corrosion If the caravan is located in a salty environment this should be done regularly n winter slippe
14. he button ON OFF no 5 to switch the levelsystem OFF User manual E amp P HYDRAULICS 4 2 Manual levelling The procedure for manual deployment extension of the axle and corner supports is as follows The manual levelling function is mainly used when automatic levelling is not possible due to a large tilt of the caravan With the help of this feature it is also possible to change the position of the caravan think of your sleeping comfort Most people prefer to sleep with their head up slightly Depending on the orientation of the caravan with this feature you can manually adjust the angle where necessary REMARK On the side where the caravan is low fill the space under the axle support footplate with some boards to compensate the difference in height This will avoid the risk it is not possible to level the caravan due to a too large difference in height In case of too large height difference the hydraulic Jacks may come to the end of their stroke zl i ON I OFF A AUTOMATIC LEVELING SYSTEM OR e MANUAL MODE no 6 Step 1 Press 1x on the button ON OFF no 5 to switch the levelsystem ON Ep The E amp P logo LED lights up indicating that the levelsystem is switched on t When there is insufficient or no battery voltage the indicator LED LOW VOLTAGE no 2 lights up E In manual levelling the caravan must be tilted a few degrees forwards The syste
15. he maximum slope on which it is possible to level the caravan is 8 With the electronic spirit level the caravan is adjusted horizontally over its complete width with the aid of the two axle supports Then the caravan is adjusted horizontally in the longitudinal direction with the aid of the four corner supports The whole caravan will be stabilized via the control panel or the optional remote control 1 3 Specific characteristics of the hydraulic levelsystem Automatically extending the jacks from a retracted position Automatically retracting the jacks from a extended position Automatically or manually levelling the jacks User manual E amp P HYDRAULICS The E amp P Hydraulics levelsystem continued 1 4 Operating instructions Before taking into service the following points must be observed The noseweight A may not exceed the max 100 KG Make sure the that the ground is sufficiently even and that there are no holes and other obstuctions present Place the caravan on a firm footing otherwise the axle supports may sink into the ground It is important that when you use the system the caravan is standing facing slightly downhill B Never use the system when there is anything attached to the caravan such as an awning or a canopy Never use the levelsystem in automatic mode when the caravan is attached to the vehicle A Jy Max 100 KG n T ke LV e The following safety precautions m
16. ial and or workmanship In order to implement the guarantee E amp P Hydraulics can at its own discretion and preference write a credit note for the defective product part either repair or replace the defective product part at no additional charge by an appointed E amp P Hydraulics authorised technician at a location to be designated by E amp P Hydraulics This location can be the E amp P Hydraulics factory another repair facility or the location where the defective product part is at the moment repair on location If E amp P Hydraulics on a reguest as worded would be willing to deviate from her herein at its own discretion and preference choices made if necessary appropriate fees will be charged such at the sole discretion of E amp P Hydraulics The manufacturer s warranty is only valid if the product is purchased from an authorised E amp P Hydraulics dealer The guarantee expires if installation modification maintenance or repairs are made to the product or its components by a non E amp P Hydraulics authorised dealer or installer Any attempt to repair a defect will inevitably lead to voiding the warranty An appeal on the manufacturer s limited factory warranty is only eligible for adoption if an official E amp P Hydraulics dealer or installer determines the material and or manufacturing defect within the warranty period and the appeal to guarantee is done within two weeks after this determination E amp P Hydraulics asse
17. irection d Step 5 Press the button JACKS REAR no 11 until the corner supports at the rear side are touching the ground Attention The level system does NOT stop automatically Step 6 Press 1x on the button ON OFF no 5 to switch the levelsystem OFF User manual E amp P HYDRAULICS 4 3 Retracting the jacks Follow the procedure below to retract the axle and corner supports i ON OFF no 5 RETRACT ALL JACKS no 8 Step 1 Press 1x on the button ON OFF no 5 to switch the levelsystem ON Ep The E amp P logo LED lights up indicating that the levelsystem is switched on IT Step 2 Press 1x on the button RETRACT ALL JACKS no 8 The indicator LED JACKS NOT FULLY RETRACTED no 4 goes out when all jacks have been fully retracted Step 3 Press 1x on the button ON OFF no 5 to switch the levelsystem OFF IMPORTANT Before departure ensure all supports have been retracted User manual E amp P HYDRAULICS 5 Extra functions 5 1 Calibration setting the zero point The calibration procedure described below has already been carried out at your dealer installer You don t have to perform this procedure by yourself E amp P Hydraulics has decided to include this chapter as an extra in this manual in case of failure and or service amp repair matters Consider setting the zero point as a condition to make it possible to level the caravan automatically and or manually Wh
18. m See also chapter 3 3 for the extended function declaration concerning buttons and indicator LED s AUTOMATIC LEVELING SYSTEM w Ep ZUERST HANDBUCH LESEN LISEZ TOUTES LES INSTRUCTIONS Function declaration LED Slope too steep 1 2 LED Battery low voltage 3 LED Withdraw front wheel 4 LED Jacks not fully retracted 5 Button ON OFF 6 Button Manual mode 7 Button Automatic mode 8 Button Retract all Jacks LEES EERST DE GEBRUIKSAANWUZING tt LED Manual mode Button Jack left Button Jacks rear Button Jacks front Button Jack right LED Level indicator LED E amp P logo User manual E amp P HYDRAULICS 3 2 Functions on the remote control The diagram below shows the appearance of the remote control By using the remote control you can operate the hydraulic levelsystem See also chapter 3 3 for the extended function declaration concerning buttons and indicator LED s HYDRAULICS 23 LEVELING SYSTEM Function declaration LED Slope too steep 9 LED Manual mode 1 2 LED Battery low voltage 10 Button Jack left 3 LED Withdraw front wheel 11 Button Jacks rear 4 LED Jacks not fully retracted 12 Button Jacks front 5 Button ON OFF 13 Button Jack right 6 Button Manual mode 14 LED Level indicator 7 Button Automatic mode 15 LED Remote control battery low 8 Button Retract all Jacks User manual E amp P HYDRAULICS 3 3
19. m will indicate whether you have positioned the caravan level enough If you have not the indicator LED FRONT WHEEL no 3 lights up di Step 2 Press 1x on the button MANUAL MODE no 6 The indicator LED MANUAL MODE no 9 lights up indicating the manual levelling procedure may begin m When the caravan leans too steeply the indicator LED SLOPE TOO STEEP no 1 lights up although this LED lights up you are able to level User manual E amp P HYDRAULICS 4 2 Manual levelling continued JACK LEFT no 10 JACKS FRONT no 12 JACKS REAR no 11 LEVEL no 14 JACK RIGHT no 13 if i Step 3 In most common cases one ORANGE arrow on the control panel no 14 lights up indicating the caravan has to be lifted on the left side or the right side BEFORE lifting this side FIRST lower the other axle support by holding button JACK LEFT no 10 or JACK RIGHT no 13 until it touches the ground Then the axle support as indicated on the control panel no 14 can be extended by holding button JACK LEFT no 10 or JACK RIGHT no 13 The levelling procedure automatically stops when the caravan is levelled in the left to right direction The ORANGE arrow level LED no 14 goes out l Step 4 Hold the button JACKS FRONT no 12 until the ORANGE arrow level LED no 14 goes out Extention of the front corner supports will automatically stop when the caravan is levelled in the front to rear d
20. mits valid for this device pursuant to EN300220 EN301489 EN60950 rules conform 868MHZ These limits are designed to provide reasonable protection against harmful interference when this product is operated in a commercial environment Any unauthorized changes or modifications to this device could void the user s authority to operate this equipment For CE countries This device is in conformity with the CE standards Please note that this device can ONLY be used with the official E amp P Hydraulics level system parts to conform to these standards C E amp P Hydraulics user manual caravan UK vers 201115 User manual Index Chapter Chapter Chapter Chapter Chapter Chapter Chapter Chapter Chapter 8 9 Chapter 10 Chapter 11 Preface The E amp P Hydraulic levelsystem 1 1 Operating of the levelsystem 1 2 Using the levelsystem 1 3 Specific characteristics of the levelsystem 1 4 Operating instructions Safety warnings Control functions 3 1 Functions on the control panel 3 2 Functions on the remote control 3 9 Extensive function declaration Operating the levelsystem 4 1 Automatic levelling 4 2 Manual by hand levelling 4 3 Retracting the Jacks Extra functions 9 1 Setting the zero point calibration 5 2 Remote control programming optional 9 9 Emergency pump when installed Schematic diagram Remarks and recommendations Troubleshooting error mode Maintenance Warranty Not
21. nt in manual mode User manual 9 Troubleshooting E amp P HYDRAULICS In case of an error message check or the caravan stands not too high at the front front wheel must be withdrawn whether the battery has sufficient voltage whether the oil level is correct whether there is any damage to the jacks and check all the cables If this does not lead to a solution for the fault the fault could be located in the drive units As the drive unit does not have any repairable parts you should contact your E amp P Hydraulics dealer installer Under normal circumstances all LED s are off and the unit will only respond by pressing the button ON OFF no 5 switching the levelsystem on Problem e The system fails to start e The red battery lamp lights up e When the red battery lamp Lights continuously the Installation is switched off for 4 minutes e The support Jacks do not extend towards the ground when the pump is running e The system does not work automatically lamp front wheel lights up NOTHING works even no LED signal Possible causes Battery voltage low Oil level to low or no oil in the system The pump is not working correctly There is no or bad electronic connection Caravan stands too high on the front side Possible cause the battery is fully out of order lt 5V Solution s e Recharge the battery Charger is defective or there Is no voltage being supplied e Check
22. oceed as follows Step 1 Using the Allen key turn the gold hexagon bolt on the emergency hand pump clockwise to the right open position Step 2 Place the metal tube handle into the black holder on the emergency hand pump assembly Pump back and forth with the metal tube until all hydraulic jacks are withdrawn all jacks will be withdrawn at the same time The moment you feel pressure resistance building up during this movement is the sign the jacks are fully withdrawn Step 3 Remove the metal tube from the holder Step 4 Using the Allen key turn the gold hexagon bolt on the emergency hand pump assembly carefully anticlockwise to the left until it locks closed position Attention carefully turn to the locked closed position a ot ot UYM ot e s ot ot ot ot Step 4 Gold colored hexagon bolt carefully open and close Place the metal tube into the holder and pump until you start to feel pressure Step 2 3 gt User manual E amp P HYDRAULICS 6 Schematic diagram of the hydraulic levelsystem Below the schematic view diagram of the E amp P Hydraulics levelsystem Hydraulic corner support front side right SS Saas See Battery not included mu TR m Hydraulic Pump A Ca e a Lu ooo ID LLL E Remote control optional mn mm e t e ee Gl ma mum mus Rum RR RU REM
23. rt the 9V battery and carefully reassemble the battery cover in most cases the battery Is already fitted Remote control Battery 9V Product CE label Battery cover Registraton label 9 2 4 Programming the remote control calibrate pair Step 1 In order to pair the remote control to the system remove the fuse 30Amp in the cable assembly of the hydraulic levelsystem Step 2 Press the buttons AUTOMATIC MODE no 7 and RETRACT ALL JACKS no 8 simultaneously When done the Indicator LED no 14 with the surrounding 4 arrows starts blinking GREEN ORANGE rapidly This means the remote control is looking for its receiver mounted within the operating system Step 3 Reconnect the fuse to the system he pairing process should be made within a certain time apr 20 sec he remote control turns off automatically When the Indicator LED no 14 goes off the pairing process is complete User manual E amp P HYDRAULICS Remote control continued 9 2 5 Putting the remote control into use After programming the remote control you now have the possibility to operate the levelsystem with it Step 1 Switch the remote control ON by pressing button ON OFF no 5 for at least 1 second Now the GREEN LED will light up by flashing As long as you see this LED flashing the remote control is searching for contact with the operating system When contact is made the flashing stops The illumination of one or two ORANGE
24. ry conditions we advise you to take additional safety and precautionary measures Especially because your safety during operation of the system For optimal performance under extreme conditions 30 degrees we recommend the use of a special hydraulic oil for low temperatures consult an authorized dealer Furthermore during the winter period we have to deal with situations in which de icing salt will tack to the outside of the system Preventative maintenance should be Good cleaning of the jacks Clean the stainless steel cylinder piston rod and spray with a silicone lubricant Remove dirt from the stainless steel foot plate especially at the bottom this is the area your caravan stands on Try to put the caravan in a location as clean and flat as possible Place a piece of rubber e g piece of carpet between the frozen slippery surface and the the footplate Before leaving make an additional check round the caravan if necessary remove snow and ice from the jacks then you are free to withdraw the jacks User manual E amp P HYDRAULICS 10 Warranty E amp P Hydraulics has a limited factory warranty for parts of the hydraulic leveling system This manufacturer s warranty applies solely and strictly on the following conditions and exclusions 1 2 OO EN C1 O gt NJ co The guarantee is valid for a period of 24 months from date of purchase This guarantee covers only defects caused by mater
25. ser manual E amp P HYDRAULICS 4 Operating the levelsystem 4 1 Automatic levelling The procedure for automatic deployment extension of the axle and corner supports is as follows ON OFF no 5 n pu no 7 READ MANUAL an LEES EERST DE eet NWIJZING ZUERST HANDBUCH LESEN LISEZ TOUTES LES INSTRUCTIONS m When there is insufficient or no battery voltage the indicator LED LOW VOLTAGE no 2 lights up fi In automatic levelling the caravan must be tilted a few degrees forwards The system will indicate whether you have positioned the caravan level enough If you have not the indicator LED FRONT WHEEL no 3 lights up and the system cannot be started automatically The front wheel must be wound down m When the caravan leans too steeply the indicator LED SLOPE TOO STEEP no 1 lights up REMARK When the caravan leans too steeply the caravan cannot be auto matically levelled You now have two options Stop the levelling procedure and place the caravan on a flatter surface and start again with automatic levelling procedure Or go further with manual levelling procedure E Step 2 Press 1x on the button AUTOMATIC MODE no 7 to start the automatic T levelling procedure Za When the levelling procedure is complete the indicator LED LEVEL no 14 lights up GREEN REMARK Depending on the angle of the terrain and type of caravan the automatic levelling procedure takes about 1 minute O Step 3 Press 1x on t
26. sses independently and exclusively or a guarantee reguest may or may not be allocated Repair and or restoration work must not be started before the warranty claim is assigned by E amp P Hydraulics and the planned repair is approved by E amp P Hydraulics Any work carried out beforehand will result in the loss of warranty coverage A warranty claim must be made promptly upon discovery of the problem to E amp P Hydraulics Should this not be the case E amp P Hydraulics can reject the warranty claim especially if the problem could be exacerbated by the late reporting this is at the sole discretion of E amp P Hydraulics User manual E amp P HYDRAULICS Warranty continued 9 In the event of damage caused by abuse misuse overloading improper loading including incorrect weight distribution improper maintenance incorrect connection connection to wrong parts negligence accident intent or deliberate recklessness it is at the sole discretion of E amp P Hydraulics to void the warranty 10 E amp P Hydraulics is not liable for any form of physical financial or physical direct or consequential damage caused by parts of the product except where the damage concerns the product itself as per the regulations provided in Directive 85 374 EEC 11 Excluded are parts of products which are used for commercial business in the sale or on offer or sold with defects and or products where the E amp P Hydraulics identification signs have b
27. ust be observed when positioning the caravan The caravan must be unhitched from its towing vehicle Apply the caravan hand brake securely Make sure that when the system is being operated no one is present in the vicinity of the caravan Note that there are no loose objects under the caravan Make sure that when levelling is being carried out no one is in the caravan An acoustic signal will be sounded during the levelling process The levelling program cab be stopped at any time by pressing the ON OFF button on the control panel or optional remote control Before driving off check to make sure that all supports have been withdrawn User manual E amp P HYDRAULICS 2 Safety warnings Fail we to observe the following warnings may lead to damage to the caravan and or serious physical injuries Using the E amp P Hydraulics levelling system for other purposes than supporting the caravan is officially forbidden according to E amp P Hydraulics limited warranty This product is exclusively developed as a levelling system and is not designed to be used for other work underneath the caravan If the system is utilised to help with changing a wheel it is the responsibility of the user to ensure the caravan is secured safely in position Never lie underneath a jacked up vehicle as this is dangerous and could result in serious injury Please always refer to your caravan manufacturer s recommended jacking procedures

User manual Levelsystem Caravan

Contents

Download Pdf Manuals

Related Search

Related Contents