Unpacking Information
Contents
1. 5 LONGSHINE since 1981 Longshine Technologie Europe GmbH www longshine de FCC Certifications FE This Eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning This eguipment complies with the reguirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information i2. TN One Gigabit Ethernet Switch One power cord Rubber foot and screws Rack mount brackets for 19 model User s Manual SV Pu oes Introduction to 100 1000Mbps Ethernet Switch General Description The device is a 100 1000Mbps Ethernet Switch Compare to the traditional 10 100Mbps Ethernet the switch delivers a dedicated Gigabit connection to every attached client with no congestion issue The gigabit ports also provide the fat pipe to the server or backbone connectivity for boosting the total system performance Moreover the NWay auto negotiation operation automatically negotiates with the connected partners on the network speed and duplex mode that provides an easy way to integrate 10 100 1000Mbps networks with no pain It is ideal for micro segmenting large networks into smaller connected subnets for improved performance enabling the bandwidth demanding multimedia and imaging applications Store and forward switching mode promises the low latency plus eliminates all the network errors including runt and CRC error packets To work under full duplex mode transmission and reception of the frames can occur simultaneously without causing collisions as well as double the network bandwidth The switch is plug n play without any software to configure and also fully compliant with all kinds of network protocols Moreover the rich diagnostic LEDs on the front panel provide the operating status of i
3. all cables Backbone Network Application This page provides a sample of network topology as a high bandwidth backbone For upgrading the 100Mbps network it s the ideal choice You can connect the switch with existing switches hubs and any PCs or servers with 1000Mbps NIC Jumbo frame For 24 port Model The 24 port model provides 9K jumbo frames which means the frames size is larger than normal 1 5K With the Jumbo frame function you can get better network performance because the switch can send more data at the same time with lower CPU usage Product Specifications e Pe OI M Standard IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE802 3x full duplex operation IEEE802 3ab 1000BASE T 1 n Interface 16 10 100 1000Mbps 24 10 100 1000Mbps auto MDI MDI X auto MDI MDI X P Cable RJ 45 10BASE T Category 3 4 5 UTP STP Connections RJ 45 100BASE TX Category 5 UTP STP RJ 45 1000BASE T Category 5 5e or enhanced i UTP STP ho AONE E EEE E R E EEEAE E A Transmission 10 100Mbps Full duplex Half duplex Mode 1000Mbps Full duplex EUER E LED System indications Power RJ 45 Port 10 100M 1000M link act NOR Line Memory 4K MAC entries 8KMAC entries NOH 272K Buffer Memory 400K Buffer Memory _ Jumbo frame 8 N A LK bytes PAE o L EE O es za iu Y Operating 10 90 oo Power Sup
4. an provide the operating status of individual port and whole system Power LED This indicator lights green when the switch is receiving power otherwise it is off P Steady Green Power is on poe Off Power is off Port LEDs Port LEDs indicators locate on the front panel for showing the operating status of 10 100 1000Mbps Ethernet switching ports Speed LED 10Mbps The 10 100M LEDs will show steady amber The LEDs will blink amber while data receiving or transmitting 100Mbps The 10 100M LEDs will show steady green The LEDs will blink green while data receiving or transmitting 1000Mbps The 1000M LEDs will show steady green The LEDs will blink green while data receiving or transmitting 10 100M Steady Blinking Amber Connected as 10Mbps Active Steady Blinking green Connected as 100Mbps Active 1000M Steady Blinking green Connected as 1000Mbps Active The Rear Panel The rear panel of the switch is shown as below 13 inch Model 16 port AC LINE 100 240 vA SAMa eo 3 0A Max 13 inch Model 24 port AG LINE 100 240 VAC Ey 30A Max 19 inch Model 16 port AG LINE 100 240 VAC ai 30A Max 19 inch Model 24 port Power Receptacle For compatibility with electric service in most areas of the world the switch s power supply automatically adjusts to line power in the range 100 240V AC 50 60Hz Plug the femal
5. e end of the power cord firmly into the receptacle on the rear panel of the switch Plug the other end of the power cord into an electric service outlet then the power will be ready Installation of 100 1000Mbps Ethernet Switch This switch can be placed directly on your desktop or mounted in a rack After completing the device installation and you can immediately use the switch simply by attaching the cables and turning the power on Desktop Installation For desktop installation the switch needs to put on a clean flat desk or table close to a power outlet Plug in all network cables and the power cord then the system is ready Before installing the switch you must ensure 1 Itis accessible and cables can be connected easily 2 Cabling is away from sk Sources of electrical noise such as radios transmitters and broadband amplifiers Power lines and fluorescent lighting fixtures 3 Keep water or moisture off 4 Airflow around the unit and through the vents in the side of the case is great for heat radiation company recommends that you provide a minimum of 25 mm clearance To prolong the operational life of your units 1 Never stack unit more than eight sets high if freestanding 2 Do not place objects on top of any unit or stack 3 Do not obstruct any vents at the sides of the case Station connection Connect each station to the switch by twisted pair cable Plug one RJ 45 connector i
6. n this document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2003 All Rights Reserved Document Version 2 0 Table of Contents Unpacking Information erect 1 Introduction to 100 1000Mbps Ethernet Switch 2 General Description ss dnu o coh ect ii oet 2 Key Peabutes accede tolit ena iuv tens 3 The Front Kamel zil oe Soda d eto oh Oba 4 LEDS DENNO Nann iiini cede 4 The Rear Panel sius ot added od totas 6 l ower Receptacle ect 6 Installation of 100 1000Mbps Ethernet Switch 7 Desktop Installation 1 eterne 7 Station Connection cernere to tote i t tne tarnen 8 Switch CONnMECHON e dee ertet tote oia ide oos 8 Rack mount Installation ess 8 Backbone Network Application 9 WMO frae lk a ait been dolu 9 Product Specifications s i cciccssceiciscasessesarcdassscccssstdseseassans 10 Unpacking Information Thank you for purchasing the 100 1000Mbps Ethernet Switch Before you start please check all the contents of this package The product package should include the following E E n A if ES f O ang d amp
7. ndividual port and whole system Key Features Complies with 10BASE T specifications of the IEEE802 3 standard Complies with 100BASE TX specifications of the IEEE802 3u standard Complies with 1000BASE T specifications of the IEEE802 3ab standard 16 24 10 100 1000Mbps RJ 45 Nway ports Supports NWay protocol for speed 10 100 1000Mbps and duplex mode Half Full auto detection Supports MDI MDI X auto crossover Supports full and half duplex operation on all ports Supports back pressure half duplex and flow control IEEE 802 3x Wire speed packet filtering and forwarding rate Store and forward architecture filters fragment amp CRC error packets Supports 4K 16 port 8K 24 port MAC address entries in whole system 272K 16 port 400K 24 port Bytes buffer memory Support up to 9K bytes jumbo Frames 24 port only Supports extensive LED indicators for network diagnostics 13 19 rack mountable Internal power adapter FCC Class A CE The Front Panel The front panel of the switch is shown as below Please refer to the following table for LED definition 100E TOONS 10MbpR d ACT hud xs oe a ul yit TTT Ahhh E soo PPR 4 Fer 13 inch Model 16 port TT dh dh dh errr Sere errr 122x 13 inch Model 24 port PRR oc nuseve son es Mss ERRE diba l lu dolo do lu FEFE Fe FEFFE 19 inch Model 24 port HTE LEDs Definition The rich diagnostic LEDs on the front panel c
8. nto a RJ 45 port of the switch and plug the other RJ 45 connector into the station s network adapter Power on the switch and then system is ready Switch connection In making a switch interconnection you could use any port to connect another switch with straight or crossover cable As all the ports support auto MDI MDI X function using a straight cable to make a switch to switch connection is allowed For cable selection refer to the following table Media Speed Wiring 10Mbps Category 3 4 5 UTP STP 10 100 1000Mbps copper 100Mbps iCategory 5 UTP STP 1000MbpsiCategory 5 5e UTP STP Rack mount Installation The 19 model may standalone or may be mounted in a standard 19 inch eguipment rack Rack mounting produces an orderly installation when you have a number of related network devices The switch is supplied with rack mounting brackets and screws These are used for rack mounting the unit Rack Mounting the Switch in the 19 inch rack 1 Disconnect all cables from the switch before continuing 2 Place the unit the right way up on a hard flat surface with the front facing toward you 3 Locate a mounting bracket over the mounting holes on one side of the unit 4 Insert the screws and fully tighten with a suitable screwdriver 5 Repeat the two previous steps for the other side of the unit 8 6 Insert the unit into the 19 rack and secure with suitable screws not provided 7 Reconnect
9. ply Internalpowersupply Internal power supply i 5V8A i 5V10A 100 240V 50 60Hz 100 240V 50 60Hz 61NB 70240 200
Download Pdf Manuals
Related Search