STYX Manual
Contents
1. for low speakers can be connected here Unbalanced mono master output on jack connector This output is transformer isolated from the mixer You can connect external light control equipment safely by using this special output Cinch connectors for all stereo channels Channel 6 has two identical line inputs Channels 5 3 have both an input for turntables Phono and an input for equipment like CD players samplers keyboards and recorders Line When turntables are being used these must be earthed by means of the earth clamp Electronically balanced microphone input on XLR connector When used unbalanced connect pen 1 and 3 with the shielding of the cable Both channels are equipped with a secondary stereo line input On all channels an optional remote start connector can be delivered As soon as the fader of the concerning channel is opened the contact between tip and ring of this mini jack 8 5 mm connection is made With this the connected equipment can be remote started The remote connection is NOT suitable for switching mains voltage Mains fuse Dimension 5x20mm small 315mA fast Euro style mains inlet Before connecting the Styx for the fist time check if your Styx is meant for the mains voltage in your country label on the connector board at the rear For all cinch connectors White Left Red Right EN Operation Dateq Styx Manual 8 Microphone channels 1 and 2 These two channels have bee2. NC connector for an optional gooseneck lamp 12 VDC max 3 W METER 2 x 12 segments LED indication of the Master Monitor or PFL level An operation level of approximately 0dB is normal Master Monitor This switch selects the signal that is indicated by the meter Each time it is pressed the meter toggles between the Master and Monitor signal The currently selected signal is indicated by LEDs Technical specifications Technical Specifications MONO INPUT MIC channel 1 and 2 Signal level Impedance Input noise Headroom STEREO INPUTS PHONO channel 3 4 and 5 Signal level Input impedance Input noise Channel separation LINE channel 1 6 Signal level Input impedance Input noise Channel separation TONE CONTROL OUTPUTS BALANCED MASTER XLR MASTER OUT MONITOR Cinch RECORDER Cinch MONO SUB 6 3 mm TRS Jack LIGHTSHOW 6 3 mm TRS Jack PHONES 6 3 mm TRS Jack FREQUENCY RESPONSE MIC TO MASTER ALL OTHER INPUTS TO MASTER THD IM GENERAL POWER SUPPLY Mains voltage Power consumption Lamp connection SIZE AND WEIGHT Dateg Styx Manual XLR 3 female electronically balanced 54 dB 600 variable 3 KQ nominal lt 107 dB IHF A 20 dB Cinch 42 dB 47 kQ variable 47 kQ 25pF nominal gt 80 dB IHF A gt 65 dB 1 kHz Cinch 14 dB 600 Q variable 22 kQ nominal gt 80 dB IHF A gt 65 dB 1 kHz 10 kHz 15 dB Shelving 80 Hz 15 dB Shelving 12 kHz 15 dB Shel
3. R B routing select switch every channel can be sent directly to the master output or to the crossfader inputs A or B giving much more creative possibilities With this feature you are totally free to select which channels to crossfade Aconnected amplifier is protected against on and offswitching blobs by means of outputrelais on the master and monitor outputs Product support For questions about the Styx accessories and other products please contact Dateq Audio Technologies B V De Paal 37 1351 JG Almere The Netherlands Telephone 31 36 5472222 Fax 31 36 5317776 E mail info dateq nl Internet www dateq nl 5 Dateq Styx Manual Mounting EN Mounting the Styx The Styx can be used as stand alone or built in mounted The housing fits in an opening of 448 x 294 x 107mm W x H x D See also the drawings below When mounting reckon with the extending of the connectors on the backside of the Styx CUT OUT lt 294mm 448 mm 10 mm MONO SUB LIGHTSHOW o o FUSE Asm Trengfiprmer puid a5 x Hit CAUTION Hisk of aleactrical shiek Do nat opa EN Connections Dateq Styx Manual 6 Styx Connectorboard The connections for all audio in and outputs are situated at the backside of the Styx The mains inlet and the fuse are also located here Be D B OG a ES AC VTC 1 a n Herr PINCE MONNIER Le HEY ere QI nick D on 1mh sam L R Balanced Master O
4. STYX USER MANUAL alll ll III II HUI DIAITIEJQ ade lectenotagies Dateq Styx Manual Safety instructions EN Safety instructions 1 2 3 10 11 12 13 14 15 16 All safety instructions warnings and operating instructions must be read first All warnings on the equipment must be heeded The operating instructions must be followed Keep the operating instructions for future reference The equipment may never be used in the immediate vicinity of water make sure that water and damp cannot get into the equipment The equipment may only be installed or fitted in accordance with the manufacturer s recommendations The equipment must be installed or fitted such that good ventilation is not obstructed in any way The equipment may never be installed in the immediate vicinity of sources of heat such as parts of heating units boilers and other equipment which generates heat including amplifiers Connect the equipment to a power supply of the correct voltage using only the cables recommended by the manufacturer as specified in the operating instructions and or shown on the connection side of the equipment The equipment may only be connected to a legally approved earthed mains power supply The power cable or power cord must be positioned such that it cannot be walked on in normal use and objects which might damage the cable or cord cannot be placed on it or against it Special attention must be paid to
5. ediately if there has been a channel selected on both sides With the TRANSFORM ON switch left pushed in the TRANSFORM ON LED lights up both the A and the B side of the crossfader will not be heard on the master output Both crossfader signals will now only be passed on if the TRANSFORM switch right is pushed in In this way short fragments can be made audible in a very simple way EN Operation Dateq Styx Manual EI Master section The master section has volume controls for the various outputs of the Styx and a 2 x 12 segments LED bar meter which indicates the Master Monitor or PFL signal level POWER Mains power switch MON Volume control for the unbalanced stereo Monitor output MASTER Volume control for the balanced stereo Master the unbalanced stereo Out and unbalanced mono Sub outputs PFL led This LED lights up if the PFL function is not active and the master signal is audible on the PHONES output BAL Determines the balance between the left and the right channel When in mid position the left and right channel can be heard evenly loud PFL Volume control for the headphone output SPLIT Determines the use of the headphone when PFL is activated Normally only the stereo PFL signal can be heard When SPLIT is active LED lights up PFL can be heard on the right side of the headphone the Master signal can be heard on the left side of the headphone PHONES Stereo headphone output Meter section LAMP B
6. n designed to connect microphones They are equipped with an input selector volume control a 2 way tone control optimized for voice crossfader routing selector and pre fader listening Mic Line GAIN HIGH LOW PFL FADER Input selector Normally the Mic input is selected Pushed in is Line CD MD tape LEDs indicate which input is selected Determines the pre adjustment of the volume for both the Mic as well as the stereo Line input High tones control Low tones control A MASTER B Signal routing selector When switched to A the signal will flow through the A side of the crossfader left to the master output In position B the signal will flow through the B side of the crossfader right to the master output In the MASTER position the signal goes directly to the master Switches pre fader listening on and off When this function is active the headphone will switch to PFL and the input signal of one or more inputs can be heard even though the fader is closed A LED will indicate whether the PFL function on this channel is active 100 mm fader through which the volume of this channel can be determined precisely The volume of a channel is also controlled by the crossfader if the channel is routed to the A or B side of the crossfader E Dateq Styx Manual Operation EN Turntable Line channels 3 4 and 5 These three stereo channels each have two inputs Phono for turntables and Line for equi
7. pment like CD players and MD recorders volume control 2 way tone control crossfader routing selector and pre fader listening Input selector Normally the Phono input is selected Pushed in is Line CD MD tape LEDs indicate which input is selected Determines the pre adjustment of the volume for both the Phono as well as the stereo Line input Line Channel 6 This channel has an input selector for the two identical stereo line inputs for equipment like CD players and MD recorders volume control 2 way tone control crossfader routing selector and pre fader listening Line 1 Line 2 Input selector Normally the Line 1 CD MD tape input is selected Pushed in is Line 2 LEDs indicate which input is selected GAIN Determines the pre adjustment of the volume for both the Line 1 as well as the Line 2 input Crossfader and Transform Normally all channels are mixed directly to the master output with the A MASTER B switch in the center position However the channels can also be sent via the A or B side of the crossfader to the master Channels via the A side cannot be heard with the crossfader in the outmost right position Channels via the B side cannot be heard with the crossfader in the outmost left position LEDs A and B above the crossfader indicate if the signal is switched to the A side or the B side of the cross fader with a crossfader routing select switch This avoids mistakes because you can see imm
8. the point at which the cable is attached to the equipment and where the cable is connected to the power supply Ensure that foreign objects and liquids cannot get into the equipment The equipment must be cleaned using the method recommended by the manufacturer If the equipment is not being used for a prolonged period the power cable or power cord should be disconnected from the power supply In all cases where there is a risk following an incident that the equipment could be unsafe such as if the power cable or power cord has been damaged if foreign objects or liquids including water have entered the equipment if the equipment has suffered a fall or the casing has been damaged if a change in the performance of the equipment is noticed it must be checked by appropriately qualified technical staff The user may not carry out any work on the equipment other than that specified in the operating instructions aude tectnotegies EN Dateq Styx Manual Introduction ES Mix With The Styx C d RW AGR RANE AA v t da i a l k age ee Al a ut mt The Styx has been designed specifically for the use in clubs etc The mixer has two microphone inputs three turntable inputs and one line input All channels are switchable to an extra stereo line input This makes the Styx a 12 input 6 channel mixing console Each channel has a gain control and a 2 way equaliser With the A MASTE
9. utputs XLR 3 pins male Audio GND A GND Out Mon Rec Stereo Outputs Cinch female Pin Function Type Shield Audio GND A GND Mono Sub Lightshow Outputs TRS Jack 3p Pin Function Type EEE a Phones Output TRS Jack 3p Pin Function Tye Phono Line Line 1 Line 2 Stereo Inputs Cinch female Pin Function Type OE Shield Audio GND A GND Balanced Mic Input XLR 3 pins female Pin Function Tye Connections MASTERL R OUT MON REC MONO SUB LIGHTSHOW CHANNELS 6 3 CHANNELS 2 1 REMOTE FUSE MAINS Dateq Styx Manual Connections Electronically balanced master outputs for the left and right channel on XLR connectors This type of output guarantees a perfect signal transport even when long audiocables are being used These outputs are equipped with relays to prevent audible blobs on connected equipment when the Styx is switched on or off Unbalanced master output on cinch connectors Can be used to connect the Styx to an amplifier or a recorder Unbalanced monitor output on cinch connectors Can be used to connect a second amplifier with monitor speakers for the DJ or a second room Unbalanced recorder output on cinch connectors This output is fixed level independent from the master volume control Unbalanced low frequency output on jack connector On this output only signals with a frequency below 125 Hz are present Extra amplifiers
10. ving 50 Hz 15 dB Shelving 6 dB balanced 600 Q variable 0 dB unbalanced 600 Q variable 0 dB unbalanced 600 Q fixed level 0 dB unbalanced 600 Q lt 125 Hz 0 dB unbalanced 10 kQ transformer isolated 0 3 W 4 Q Impedance 4 32 Q 80 Hz 25 kHz 1 dB 20 Hz 25 kHz 1 dB 0 05 nominal 220 240 VAC 50 Hz BNC 12 VDC 3W 483 x 310 mm W x H 19 7HE 448 x 294 mm W x H
Download Pdf Manuals
Related Search