VISION 1480 Installation Guide
Contents
1. 11 Troubleshootingi ici se Dao on sat se sad dos ee ne ea 14 OPTIONS EEE eae area dos dan dan ane dan donna 16 Owner s Guide Kiramek Inc shall not be held liable for any errors omissions prop NOTICE Although reasonable efforts have been taken to ensure accuracy in this erty damage or injury resulting from the use of this information All product specifications and features are subject to change without notice J 2011 2015 KIRAMEK INC LIMITED LIFETIME WARRANT The VISION 1480 Control Module is backed by a limited lifetime war ranty against defective components and or improper product assembly to the original purchaser for as long the vehicle is owned by that same purchaser contingent upon installation by an Authorized VISION Deal er All product warranties become void if the VISION 1480 system was not sold and installed by an Authorized VISION Dealer or the system is moved to another vehicle All other parts and or accessories that connect to VISION 1480 systems including but not limited to the Siren Shock Sensor and LED Program Switch are warranted for one 1 year from the original date of purchase During the warranty period Kiramek Inc will repair or replace at its sole discretion any system component that is found defective in mate rial or assembly during the warranty period provided that the product is returned to Kiramek Inc by an Authorized VISION Dealer and is ac2. RIRAMER INCORPORATED 2011 2015 KIRAMEK INC Aichi Japan Ver 1 9 Aug 2015 Thank you for purchasing this VISION 1480 Vehicle Security System The 1480 is a state of the art device that will pro vide you with years of trouble free ser vice if used properly Please familiarize yourself with the content of this Owner s Guide to get the most out of your new system We trust you will enjoy using the product TABLE OF CONTENTS Limited Lifetime Warranty 1 Included toms ssania nasen aa a A E gaa sees ee 2 Arming amp Disarming 3 Armingdisrispers poianone ne Saas Pee a me mas Saeed a aes 3 Confirmation Chips rsscriguasialione share ae eee dee aes 3 DISTING sect ie es da a ode acetate ne E AS ne 4 Manual DISAIN sess sinti 5 Main FEGIUTOS Lil 6 Trunk Release Bypass esse 6 DOOM TIQUE seine e ei are nil 6 2 Stage Shock Sensor 4 sssss sssssss 6 LOMITIOM MIG OS ESS ARR ER dre in a a ee mai 7 PIOOG MAIS OC Masa Ses pies tease torus titans aaa ae Saude aera wh Gee een hed 8 Error CAD ig daccecdda nha os ea ead dtd eo bad de dat a 8 GWA Ground When Armed LL 8 SBS Sector Bypass System 8 Status LED ss gb ee ee ag wae ee Hee nn 9 Hazar RATS QE tattili taba kta agar arsed 10 R SUM siria ila 10 Valet MO 0 dan oi rata 10 Programmable Features
3. to Disarm the 1480 until you shut off the engine DISARMING DURING THE SIREN BLAST Go If the siren is triggered by the opening of a door or the back hatch you should close any open doors or the back hatch before you press Unlock on your factory remote to disarm The reason is because some cars require doors to be closed before you can Unlock with the factory keyless remote Also if the siren is blasting and the doors are already unlocked you may not be able to Disarm the 1480 with a simple press of Unlock In sucha case you will need to first press Lock and then press Unlock to Disarm This is also true in cases where the car s factory remote only has a single Lock Unlock button you ll have to push the button twice 2011 2015 KIRAMEK INC lt gt MANUAL DISARMING You can manually Disarm using a secure code in the event your factory remote s battery dies see Note 2 below The factory set code is 6 but you can change this code to another number of your choosing for greater security see the bottom of this page 1 Enter the car The siren will go off You can leave the door open or closed 2 Turn ON the Ignition 3 Within 30s press the Program Switch the same number of times as your Disarm Code Factory Default Code 6 4 Turn OFF the Ignition The 1480 will now Disarm and the siren will stop NOTE You must press UNLOCK and then press LOCK to Arm NOTES 1 If the 1480 wont Disar
4. NOTES 1 If after Auto Lock after exceeding 30km h someone then Unlocks the doors manually they will not Auto Lock a second time And be cause they are already Unlocked in such a case putting the gear into the P position will not Auto Unlock 2 In some rare cases when the doors are Auto Locked or Auto Unlocked there may be a second or two of noise appear on your in dash TV This noise has nothing to do with the 1480 product or 1480 product installa tion This is noise generated by your car s door lock motors Exterior Illumination Shi When set to ON vehicle Hazard lights will flash for 30s or until a Door is opened or until the Ignition is switched ON in order to illuminate the area around the vehicle for greater visibility and security gt VISION 1480 OWNER S GUIDE TROUBLESHOOTING FACTORY KEYLESS REMOTE WAS LOST DISARMING If the factory remote was lost you may not be able to Disarm if you have a Push Start car that requires the factory remote to turn on the Ignition In such a case you must to contact your dealer for a replacement factory remote But if you have an older turn to crank style Ignition you can Disarm the 1480 by following Manual Disarming on page 5 SOMETIMES CAN T ARM DISARM WITH THE FACTORY REMOTE e On some cars if you rapidly press Lock and Unlock on the factory re mote the 1480 may stop responding to the remote In this case the fix is simple just wait longer between Lock
5. Certification Replacement P N Operating Voltage Current Consumption Operating Temp Loudness Audio Generator Housing Certification Replacement P N D 12Vdc 3 3MA Armed w LED flashing 2 0MA Disarmed or Armed in Sensor Bypass Mode Does not include Shock Sensor consumption 40 C to 85 C IP40 While vehicle CAN sleeping 12Vac fed from Control Module 4 8mA avg when Armed OMA when Disarmed 40 C to 85 C Infra red Beam Deflection IP40 also passed IP50 tests 318 052 12Vdc 5 5mA 1480B trickle charge or OMA 1480S 1A max during full siren blast 40 C to 125 C 125dB measured 30cm 1ft from speaker tone 6 tone selectable by cutting loop on siren Water resistant cannot be submerged IP54 KB22 1 1480B or KR22 1 1480S VISION 1480 INSTALL GUIDE INCLUDED ITEMS Only 1480B includes keys Siren 1pc Sensor Tape 1pc See Note SE See pg 11 below gt Siren connection Dark RED p n NL 1 Guides 2pc PosiTap Connectors 4pcs PosiLock Connector 1pc NOTE 4 PosiTap connectors are not included when ordering the 1480 with an optional OB 22 or OB 23 OBD splitter harness because they are not needed But 1 PosiLock connector is always included for the siren 2011 2015 KIRAMEK INC READ THIS FINST ALARM FIRMWARE amp ONE TIME LEARNING FIRMWARE The 1480 only works on select cars that have a compatible digital
6. pg 11 If you are using the default IG Protect Mode you will not be able to Arm while the Turbo Timer is running because the Ignition ON condi tion in that mode prevents Arming 2011 2015 KIRAMEK INC CANNOT DISARM WHILE THE SIREN IS SOUNDING e Ensure all doors amp trunk are closed then try to Unlock to Disarm Try Locking first then Unlock SHOCK SENSOR Ist STAGE WARNING TRIGGER DOESN T WORK Examine the shock sensor and look closely at the two LEDs When you lightly tap on the sensor do you ever see a Green LED light If you never see Green light adjust the sensitivity knob on the sensor If after increasing sensitivity you still don t see the Green LED it could be that the suspended element inside the sensor body was shifted out of place See page 15 in the Install Guide on how to resolve this If you do see a Green light the sensor is functioning properly That means there is like a wiring problem Check that the sensor wire har ness is properly connected at both ends FULL SIREN BLASTS WITH ONLY LIGHT IMPACT TO THE VEHICLE You mounted the shock sensor to metal Remount on a plastic part Turn down the shock sensor sensitivity If you added an optional Ultrasonic sensor it is very likely that the controller of the ultrasonic sensor not the emitters was placed too close to the shock sensor The Ultrasonic sensor s controller should be placed more than 30cm 1 foot away from the
7. 2015 KIRAMEK INC TROUBLESHOOTING CAN LEARNING SUCCESSFUL BUT ALARM OPERATION IS ERRATIC An intermittent 12v Power or Ground connection is the most common reason for unexplained alarm behavior This should not be a problem if you used the OBD connector and if it is securely connected but be sure to reconfirm your Power and Ground wiring if you manually connected them If your power source is truly stable then the best alternate explana tion for erratic behavior is the wrong firmware There are different firmware files even within the same car family For example there are numerous different firmware files for Toyota cars alone If you have the wrong Toyota firmware and try to use it on a Toyota it wasn t intended for the alarm may function correctly sometimes but not at other times The fix is easy Just program the correct firmware USB Programming Tool required Visit your VISION dealer or speak to KIRAMEK SHOCK SENSOR ONLY FULL TRIGGERS THERE S NO WARNING TRIGGER View the sensor s LEDs when you hit the car s body If the Green LED doesn t light slightly increase the sensitivity of the shock sensor Ifthe Green LED lights perhaps you re testing too quickly After Lock ing Arming you must wait 10s before you can test the shock sensor SHOCK SENSOR GIVES REPEATED WARNING TRIGGERS Ifthe sensitivity of the sensor is too high and or if the mounting location is incorrect the sensor may be tri
8. of the vehicle BLK PERSAN MAIN HARNESS The BLACK wire is the Ground input to the 1480 Mi Be sure to connect this wire securely to a good ground source Most security system installation problems di result from a bad ground connection The easiest connection is to the factory wire behind Pin 4 of the car s OBD connector as shown in the photo on page 8 And unlike Pin 16 12v of the car s OBD Pin 4 Ground is normally not put to Sleep by some body computers If you have doubts though you can connect to body metal or an existing bolt brush with steel wool first or you can run a wire directly to the car s Negative battery terminal VISION 1480 INSTALL GUIDE BRN KANDI CAN HARNESS The BROWN wire is a digital I O line that must be con CAN L nected to the car s CAN LOW line CAN L is Pin 14 of the car s OBD connector on all Toyota Lexus and Nissan cars But on other cars it is either in a different location in the car s OBD connector or a different location in the car altogether For this reason we have prepared separate Install Guides for cars other than Toyota Lexus and Nissan which provide details on where to connect the BROWN wire N DON T CONFUSE CAN L WITH THE BROWN SIREN OUTPUT BRN RED feo CAN HARNESS The BROWN RED wire is a digital I O line that must be CAN H connected to the car s CAN HIGH line CAN H is Pin 6 of the car s OBD connector on all Toyota Lexus and Nissan c
9. security system will be completely turned off This also means that someone could break into your car Our company accepts no liability whatsoever if your car is stolen or vandalized or its contents stolen due to your hav ing entered Valet Mode You use this feature at your own security risk 2011 2015 KIRAMEK INC PROGRAMMABLE FEATURES Switch Perform the following 4 step procedure to change the fea L You can change some features of the 1480 by using the Program EA A N me tures shown in Table 2 Start the engine and then Stop the engine With the Ignition OFF Arm the 1480 and then immediately Disarm Within 20s turn ON the Ignition LED will flash if a door is open Press the Program Switch the same number of times as the feature you want to program refer to the No column in Table 2 below For example to toggle Auto Arm push the Program Switch 8 times Turn OFF the Ignition The LED will flash the same number of times as the feature you just toggled There is no Toggle Setting indication so test to confirm your programming NOTES 1 To program another feature repeat the 5 steps above 2 To reset everything to factory defaults perform the CAN Signal Learning procedure on page 14 of the Installation Guide But be sure to read the NOTE there first TABLE 2 Feature Selection Menu No Feature Description Toggl
10. the factory the siren is Disabled so it will not make any sound until you Enable it by switching the keylock to the GREEN dot position as shown at right RED dot Enabled a dot Keep the siren Disabled until you have made all your con _ nections otherwise the siren may trigger Disabled Be sure to keep your keys in two separate safe places You cannot order replacements And you will need a key if the siren goes off for some reason and you cannot shut it off by normal means with the remote BACKUP BATTERY As is true with all batteries the battery inside the 1480B s backup siren has a finite life Life varies based on the installed environment Typical life in the engine compartment is 3 years under a constant trickle charge of 5 5mA The battery is warrantied for 1 year You cannot replace the battery but the siren will continue to operate even after the battery is dead you simply will lose the backup function VISION 1480 INSTALL GUIDE D OPTIONAL CONNECTIONS GWA Output OPTIONAL PARTS REQUIRED GWA stands for Ground When Armed This wire supplies Ground 500mA max while the 1480 is Armed One common use is for connection to an optional 896H 1B starter kill relay as shown in Fig 3 below IGNITION SWITCH Another use for the GWA Output is to attach visual theft deterrents like scanning LEDs as shown in Fig 4 below These devices will turn on when the 1480 is Armed You will need to add a relay if yo
11. 015 KIRAMEK INC INCLUDED ITEMS LED Program Sw 1pc Only 14808 includes keys a Siren 1pc Control Mod Harnesses 2pcs Sensor Harness 1pc D Sensor Tape 1pc See Note gt See Installation Guide pg 11 below Siren connection Dark RED p n NL 1 25cm Wire Ties 2pcs PosiTap Connectors 4pcs PosiLock Connector 1pc NOTE 4 PosiTap connectors are not included when ordering the 1480 with an optional OB 22 or OB 23 OBD splitter harness because they are not needed But 1 PosiLock connector is always included for the siren LED Program Switch Parts Status LED Program Switch VISION 1480 OWNER S GUIDE AAMING amp DISARMING CHI a NORMAL ARMING Close all doors and then LOCK by your factory keyless remote or by SmartKey door handle touch Hazard lights will flash doors will lock and the siren will chirp 1 time if Confirmation Chirps are ON The Status LED will light for 5s during which time all triggers are disabled Then the Status LED will start flashing and Ignition Door Trunk and Hood triggers become enabled The Shock Sensor and any other external sen sor is enabled 5s after the LED starts flashing 10s after you Lock SENSOR BYPASS ARMING OFF a This procedure lets you temporarily disable 2 Pushes Cee the Shock Sensor for a single Arming session D 1 With Ignition OFF press the Program Switch twice S 2 Within 20s press LOCK o
12. CAN BUS communication system If your car is not on our compatibility lists the 1480 will not function at all We do not accept product returns due to CAN BUS data mismatching so make absolutely sure prior to purchase that your ve hicle is compatible and that firmware matched to your vehicle s CAN has been programmed into the 1480 product by your authorized VISION dealer or by our company KIRAMEK Inc Visit our 1480 web page for the latest Compatibility List May be in Japanese only Email us for assistance http visionsecurity jp en systems 1480 html ONE TIME LEARNING After you have connected the four CAN amp Power wires OBD plug and the Siren wire pages 6 12 you will need to perform the CAN Signal Learning steps on page 14 You must do the CAN Learning steps even though the 1480 has been programmed with firmware matched to your car ELECTRICAL CONNECTIONS The 1480 s OBD plug containing 2 Power wires amp 2 CAN wires is the most critical connection you will make If you do not wish to use the 1480 s OBD plug always use the included PosiTap connectors to connect the 4 wires or purchase an optional OB 22 or OB 23 splitter harness NEVER use solder unless you are experienced a surprising number of alarm installs fail due to badly soldered connections If you use solder always tape your connec tions to ensure nothing will ever short NEVER use electrotaps or T taps in place of PosiTap connectors as they can lo
13. and Unlock presses If Confirmation Chirps pg 3 are enabled did you hear a single siren chip when you tried to Arm If not the Ignition may be ON You can not Arm the system while the Ignition is ON while in IG Protect Mode see the top of page 12 THE SYSTEM IS DEFINITELY ARMED BUT IT WON T TRIGGER THE SIREN e It may be in Valet Mode See page 10 e It may be in Sensor Bypass Mode See page 3 SIREN BLASTS WHEN THE TRUNK IS OPENED You cannot open the trunk with the key or the siren will sound Use your factory remote If your keyless remote doesn t have a trunk open feature then you need to Disarm the system first Unlock button on your factory remote and then open the trunk If you open the trunk with your factory remote and the siren triggers it could be the trunk release timing is too long After pressing Trunk Release on your factory remote the trunk must open within 2s or the siren will sound e Some cars simply have a trunk release feature that is incompatible with the 1480 In this case first Unlock Disarm then open the trunk CANNOT ARM WHILE 3rd PARTY TURBO TIMER IS IN USE e Check if the doors Lock Unlock by your factory remote while the turbo timer is running If not the vehicle s factory keyless system is incom patible with your turbo timer which is why you cannot Arm the 1480 Ifthe doors do Lock Unlock with your factory remote while the turbo timer is running then make sure you have programmed RSCM
14. ars But on other cars it is either in a different location in the car s OBD connector or a different location in the car altogether For this reason we have prepared separate Install Guides for cars other than Toyota Lexus and Nissan which provide details on where to connect the BROWN RED wire 1 WIRE CAN HONDA CAN HARNESS The GREEN wire is a digital I O line that must be con nected to the single CAN line but only on certain HONDA cars Such connections are beyond the scope of this manu al so consult our vehicle specific Install Guide for details 1 WIRE CAN WARNINGS 1 NEVER use the Green wire when installing in Toyota Lexus or Nis san cars Those cars use only require CAN H amp CAN L 2 NEVER connect all 3 wires in the CAN HARNESS You either use CAN H amp CAN L as a pair or use the Green wire only 2011 2015 KIRAMEK INC SIREN CONNECTIONS BRN FOIE ASIE INT This wire supplies a 12v 2A max output to operate the included siren during a security breach Do not confuse this wire with the Brown wire of the CAN harness The way to connect the Brown SIREN wire depends on which version of siren you have The 1480S comes with a standard 2 wire siren see Fig 1 below The 1480B comes with a more advanced 4 wire siren that has an onboard backup battery see Fig 2 below STANDARD LOOP Dark Red PosiLock BATTERY FIG 1 1480S Siren Connections C
15. bes computer safe test lights included because they draw a large amount of electrical current that could overload and destroy sensitive circuitry in the vehicle Manually turn off all lights such as the dome light that illuminate when a hatch is opened so you will not run down the battery If you can not manually turn off all the lights then remove the appropriate fuses and don t forget to replace the fuses after your installation is complete Roll down a window to avoid locking the keys in the car If unsure consult the vehicle owner about where the LED Program Switch Control Module Siren and Shock Sensor should be mounted If you need a constant 12 volt power source under the dash splice off the wire leading to pin 16 POWER at back of the vehicle s OBD plug OBD pin 16 supplies a constant 12V at up to 7A When running extension wires always use a wire gauge that is as big or bigger than the wire you are extending Useful Installation Items DMM digital multi meter e Soldering Iron amp Solder Battery powered drill amp driver e Corrugate Tubing Electrical Tape or Heat Shrink Tubing e Wire Stripper Crimper Brake Cleaner or Alcohol degreaser e Wire ties VISION 1480 INSTALL GUIDE D TECHNICAL SPECIFICATIONS Control Module Operating Voltage Current Consumption Operating Temp Certification Shock Sensor Operating Voltage Current Consumption Operating Temp Sensor Technology
16. companied by a clear and legible copy of the original purchaser s receipt Any damage to your VISION 1480 system that results from normal wear and tear accidents improper use neglect faulty wiring incorrect installation modification removal or defacement of the product serial number alteration or repair outside Kiramek Inc or its Authorized VI SION Dealers immediately voids this warranty This warranty is limited to defective parts only and does not provide any compensation whatsoever for damages associated with the VISION 1480 system or its accessories This warranty does not cover installa tion labor product removal and or reinstallation fees This warranty is valid for the original purchaser only and may not be transferred to another party Kiramek Inc makes no warranty against theft or vandal ism of the vehicle in which the VISION 1480 system was installed This warranty shall not be interpreted as an insurance policy against loss nor shall Kiramek Inc be liable any in way for such loss financial or otherwise WARNING DO NOT ATTEMPT TO INSTALL THIS VISION 1480 PRODUCT YOUR SELF BECAUSE SUCH WILL IMMEDIATELY VOID THE WARRANTY THIS SECU RITY SYSTEM MUST BE PROFESSIONALLY INSTALLED BY YOUR AUTHORIZED VISION DEALER TO VALIDATE YOUR WARRANTY KIRAMEK may opt to validate the above Warranty in writing for shipments outside Ja pan in cases where there is no local VISION Dealer available to perform the install O 2011 2
17. e CAN system so CAN H and CAN L are not used at all and the 1480 s GREEN wire is used instead WARNING If you connect the OBD2 connector with all 4 wires attached to HONDA cars that have 1 wire CAN you will cause a fault in the car s body computer Such will result in a Warning light that can only be reset at the dealer at your expense READ ALL 1480 DOCUMENTATION BEFORE CONNECTING ANYTHING ORIENTING WIRES The OBD2 connector included with the 1480 has a special feature that al lows you to decide from which end the wires exit the connector as shown in the diagram atop on the next page This is useful because the direction you must insert the OBD plug varies from car to car Once you have oriented the wires as you like simply slide the cap back over the circuit board and then use a wire tie to secure the wires as shown D 2011 2015 KIRAMEK INC Wire Tie Wrap wires around PCB to the right CONNECTING THE OBD PLUG GRAS one On TOYOTA LEXUS and some NISSAN cars simply attach the 1480 s OBD plug to the vehicle s OBD plug After that connect the Siren pg 11 and then finish with the LEARNING STEPS pg 14 To hide the OBD connections cut off the 1480 s OBD plug and manually connect the 4 wires behind the vehi cle s OBD using the included PosiTap connectors or purchase an optional OB 22 or OB 23 splitter harness see pg 2 note under PosiTaps For all cars other than Toyota L
18. e Settings 3 Ignition Trigger IG Protect RSCM 4 Hazard Flash During Remote Start OFF ON 7 Door Ajar Hazard Flash OFF ON 8 Auto Arm OFF ON 9 Siren Output Continuous Pulsed 10 Auto Rearm OFF i ON 15 Speed Controlled Door Locking OFF ON 17 Exterior Illumination OFF ON FACTORY DEFAULT SETTINGS SHOWN IN BOLD TEXT ABOVE db 2011 2015 KIRAMEK INC Picnic You cannot Arm if IG is ON in IG Protect Mode When set to IG Protect Mode default the system will trigger the siren when the Ignition IG turns ON while Armed as described on page 7 When set to RSCM Remote Start Compatibility Mode the system will by pass the Shock Sensor and Ignition triggers when the Ignition turns ON while Armed as described on page 7 4 Hazard Flash During Remote Start S When set to ON hazard lights will flash for safety while the Ignition is turned on by a remote start system This feature only works if program the Ignition Trigger to RSCM Door Ajar Hazard Flash a When set to ON vehicle hazard lights will flash for safety whenever a door is opened or left open while the Ignition is turned ON Flashing will im mediately stop when the door is closed or the Ignition switched OFF NOTE The Status LED will always flash when the Ignition is ON and a door open in order to notify the driver This LED flashing cannot be disabled CHID Li This feature automatically Arms the system when you do the f
19. ens Door and Ignition switch triggers remain active and doors remain locked Five 5 seconds after you close the trunk the shock sensor and trunk triggers will be automatically re activated Z NOTE Some cars don t support the automatic trigger bypass feature of the 1480 In such cases you will need to first Unlock Disarm before you can use your factory Trunk Release feature otherwise the siren will trigger LUTTER ay The siren will blast for 30s when the trunk is opened without the remote while the system is Armed Ve hicle hazard lights may also flash See bottom half of pg 4 on Disarming in this case Also see Table 1 pg 9 DOOR TRIGGER Da pe The siren will blast for 30s when any door is opened C while the system is Armed Vehicle hazard lights may also flash See bottom half of page 4 on how to Disarm in this case Also see Table 1 pg 9 2 STAGE SHOCK SENSOR Serine Ist Stage Warning Chirps Each time the Shock OD Sensor detects a light impact to the vehicle body the si Z ren will chirp 5 times Sensors will not trigger the siren while in Sensor Bypass Mode 2nd Stage Full Trigger When the Shock Sensor de ats Blast tects a hard impact to the vehicle body the siren will OD blast for 30s or until Disarmed with the factory remote A Sensors will not trigger the siren while in Sensor Bypass Mode Also see Table 1 pg 9 See page 15 for common shock sensor problems and so
20. er to make the sensor s 2 sided tape stick more permanently Even when affixing the sensor to very rough textured car plastics the use of brake cleaner on the plastic surface will allow the sensor tape to stick permanently Failure to clean the surface may result in the tape peeling off over time which would cause the sensor to fall off and possible false trigger the siren NOTE Always mount the shock sensor and sensor wires more than 30cm 1ft away from the optional Paging System s Antenna Unit and 30cm from the controller of any attached Ultrasonic Sensor Failure to do so may cause the shock sensor to randomly false trigger the siren VISION 1480 INSTALL GUIDE ADJUSTING THE SHOCK SENSOA Full Trigger Sensitivity RED LED The shock sensor is factory preset to work well with most vehicles out of the box 50 setting Howev er if you find that the siren is going off too easily or Va if the siren doesn t go off when you think it should Farai it s time to adjust the sensitivity Warning Trigger GREEN LED Turn the sensitivity adjustment knob clockwise to increase sensitivity and counter clockwise to decrease If you cannot find a suitable adjustment level consider remounting the shock sensor False Alarms The VISION 318 052 Active IR shock sensor has been engineered to avoid false triggers in most situations However there is still the possibility the sensor could trigger the siren during a
21. exus and Nissan please consult our separate INSTALL GUIDE that is specific to your vehicle VISION 1480 INSTALL GUIDE POWER amp CAN CONNECTIONS Z NOTE Pages 9 10 describe how to MANUALLY CONNECT the Power amp CAN wires You do not need to reference these 2 pages if you have a Toyota Lexus or Nissan car unless you wish to cut off the OBD plug and make your connections manually For Honda note pg 10 For all other cars refer to our separate Install Guide If this section doesn t apply to your car or installation method jump to page 11 RED ROME MAIN HARNESS The RED wire is the 12v power input to the 1480 Be sure to connect this wire securely to a constant 12v source such as the factory wire at tached to Pin 16 of the car s OBD2 connector see BATTERY OBD photo at bottom of page 8 As of this writing Toyota Lexus and some Nissan cars do not put the fac tory OBD connect to Sleep to save power like some European cars do This means you shouldn t have a problem taking 12v from Pin 16 of the factory OBD However car makers can change their body computer at any time So if you find the 1480 shutting down when it should not your Power and or Ground connections must be suspect If you have doubts about whether the OBD is being put to Sleep run an extension wire through the firewall and attach the 1480 s RED wire directly to the positive 12v battery terminal which will bypass any Auto Sleep features
22. for the entire 30s duration of full siren triggers and Hazards will flash 2 5 times depending on the car when shock sensor Warning Chirps are trig gered But note that some cars do not support Hazard flashing at all Gp RESUME is a form of State Memory that remembers if the system was Armed or Disarmed when the main power is cut When power is restored the 1480 will power up Disarmed if it was disarmed in its previous state If originally Armed it will power up Armed and with the siren blaring eee 2 PROGRAMMABLE LI Valet mode shuts down all functions of the security system ensuring the siren will never trigger Valet Mode is useful when you must hand over your car keys to a valet or car maintenance technician so there is no worry they will trigger the siren by accident Push 5s Activation With the Ignition switched OFF and the 1480 Disarmed press and hold the Program Switch for more than 5s When you first press the switch the LED will im mediately light But the LED will turn OFF after about 5s When the LED turns OFF release the Program Switch Deactivation Press and hold the Program Switch again for 5s until the LED turns OFF Security features are now restored You may also hear 2 quick chirps the first time you Arm to inform you that you have just exited Valet Mode CAUTION When you activate Valet Mode the Status LED will not blink and you will not receive any indication of being in Valet Mode The
23. ggering on the otherwise undetectable sounds of the hazard light relay switching or even the siren vibration Reduce sensitivity and or change the mounting location of the sensor 3rd PARTY ENGINE STARTER TRIGGERS SIREN e As of 2014 many factory and aftermarket remote start systems feature a Door Open output wire that is used to trick the car into thinking a door has been opened after the remote starter shuts off Such an output is used to turn off the Headlights on cars where the Headlight Switch is set to AUTO To solve the problem DO NOT USE the AUTO setting on your headlight switch and cut or disconnect the remote start systems Door Open wire Ifthe above solution doesn t work or doesn t apply to your situation the only solution is for you to Disarm the 1480 before the remote starter shuts off the engine or remove the remote starter altogether 2011 2015 KIRAMEK INC OPTIONS The 1480 can be installed in your car without the need for any Options However we do offer the following add on products to enhance security and convenience TR537S 2 way LCD RF Paging Control System ARIB T67 for Japan TR835S 2 way LCD RF Paging Control System FCC for USA 896H 1B Starter Kill Relay 896H 1CN Relay to drive high current devices like the Horn S 114R or S 113 Pin switch to detect Hood opening OB 22 or OB 23 OBD splitter harnesses useful for simply hiding the 1480 s OBD connection OB 22 or hid
24. ing the connection AND adding a 3rd party OBD device 0B 23 Some 8rd party OBD devices may be incompatible with the 1480 Contact KIRAMEK for details Optional Sensors MMF 2 2 stage Radar Sensor e KST 24 2 stage Digital Tilt Sensor SB 03 Sensor Splitter to easily connect up to 3 sensors at once Luminator LED Scanners visual theft deterrents More details about add on devices can be found on our website www visionsecurity jp en DEAD VISION 1480 INSTALL GUIDE gt VISION products are engineered in Japan and manufactured in strict accordance with Japanese QC standards at an ISO9000 QS9000 certified factory www kiramek com 9 183 1 Itayama cho Handa shi Aichi Ken 475 0936 JAPAN TEL 81 569 20 5585 FAX 81 569 20 5586 EMAIL support kiramek com
25. low Lock Unlock while the doors and or trunk are open GWA Ground When Armed SI The 1480 feeds a Ground output while the system is Armed Optional devices can be activated by this control line such as a Starter Kill Immobilizer Relay or LED scanners When the system is Disarmed GWA is switched OFF and all attached devices turn off See the Installation Guide for electrical specifications SBS Sector Bypass System f A sector is the Ignition the Hood any Door and attached Sen PF sors When a sector triggers the siren a certain number of times A see below that sector is bypassed disabled until you Disarm KEAN and Arm again This limits noise pollution caused by multiple siren triggers in a short period of time such as when you park near construction sites or if animals jump on the vehicle repeatedly DOOR If a Door is left OPEN the siren blasts up to 5 times 30s each time then the Doors are bypassed until closed The HOOD via the GRAY input wire is bypassed after it triggers the siren 10 times IGNITION If the Ignition is left ON the siren blasts up to 10 times 30s each time and then the Ignition is bypassed until you Disarm amp Arm again SENSOR Warning triggers 5 chirps and Full Triggers 30s siren are independently bypassed after 10 times You must Disarm and then Arm again to re activate VISION 1480 OWNER S GUIDE STATUS LED The Status LED flashes slowly abou
26. lutions VISION 1480 OWNER S GUIDE IGNITION TRIGGER O PROGRAMMABLE LI IG PROTECT MODE default The siren will blast for 30 seconds when the Ignition IG switches ON while the system is Armed Vehicle hazard lights may flash To Disarm and stop the siren turn off the Ignition and then press Unlock on the factory remote REMOTE START COMPATIBILITY MODE RSCM user programmable When the Ignition switches ON while Armed in this mode the siren will not trigger Instead Shock n Kup Sensor and Ignition triggers are bypassed while Door Hood amp Trunk triggers remain active This allows 3rd party remote starters to start the engine without triggering the siren The vehicle is still protected though and any attempt to open a door or the trunk will trigger the siren And when the remote starter stops the engine i e Ignition turns off Sensor and Ignition triggers are automatically re activated See page 11 to program IIP Intelligent Ignition Protect IIP activates when you program RSCM The function of IIP is to temporarily switch back to IG Protect Mode after a siren trigger Purpose Most remote start turbo timer compatible car alarms by pass all trigger inputs after the Ignition is switched ON So if a thief opens a door the siren will trigger but the thief can then close the door turn on the Ignition wait until the siren stops then drive away in si lence because the Ignition ON state p
27. m you entered the code incorrectly Close the door wait for the siren to stop then start over from Step 1 2 Many Push Start cars don t allow the Ignition to be turned on with out the presence of the Factory Remote So if you lose or destroy your car s remote you may not be able to Manually Disarm the 1480 But if your remote s battery merely dies you will be able to switch on the Igni tion and Manually Disarm using the 4 steps above DISARM CODE CUSTOMIZATION PROGRAMMABLE LI The factory code is 6 but you should change it to another number between 1 amp 30 1 With the 1480 Disarmed turn ON the Ignition 2 Press the Program Switch for 6s after which the siren will chirp 3 times 3 Release the Program Switch and turn OFF the Ignition The Status LED will light for 5s 4 Turn ON the Ignition again while the LED remains lit for 5s 5 When the LED turns off wait about 4s and you will see the LED start to flash Take note of the flashes as the number of flashes will be the num ber of your Disarm Code Turn OFF the Ignition to program your code The LED will now flash the same number of times as your Disarm Code AE you have the optional paging system you must now relearn your pagers gt 2011 2015 KIRAMEK INC MAIN FEATURES TRUNK RELEASE BYPASS For cars that support it pressing the Trunk Release button on the factory remote will bypass the shock sensor and trunk triggers while the trunk op
28. n the factory remote to Arm The siren will chirp 2 times and all triggers door IG etc will be active except the shock sensor and any other external sensors Note that when you Disarm and then Arm again normally the shock sensor will be enabled eae herllicce ON by default PROGRAMMABLE LI VESA This procedure lets you enable or disable the 1 Push ROLE Arm Disarm chirps Note that the siren will A R still go off when the 1480 is triggered S 1 With Ignition OFF press the Program Switch once 2 Within 20s press LOCK on the factory remote to Arm The confirmation chirp state has now toggled and the system is Armed Re peat the above procedure to toggle the confirmation chirp state back again D VISION 1480 OWNER S GUIDE DISARMING Jr NORMAL DISARMING UNLOCK UNLOCK by your factory keyless remote or by SmartKey door handle touch Vehicle hazard lights will then flash doors will unlock the siren will chirp 3 times if Confirmation Chirps are ON and the Status LED will turn off The 1480 is now Disarmed and you may enter the vehicle If the siren chirps 4 times when you Disarm it means something had trig gered while you were away from the vehicle In this case the Status LED will flash to tell you what caused the trigger see Trigger Memory page 9 N NOTE Some vehicles equipped with remote engine starters do not allow you to Unlock while the engine is running In such a case you will not be able
29. not waterproof and an electrical short could occur if water gets in side Only the siren can safely be installed in the engine compart ment Do not install the 1480 control module in an environment of intense condensing humidity or steam in an area with an unusually large number of airborne particles or any place where oil could build up inside the control module case All of these extreme environments could lead to an electrical short and possible cause a fire Avoid installing the 1480 and its associated sensors near sources of intense RF transmissions which could possibly interfere with the op eration of the system If you find the system is randomly working and not working consider relocating any attached sensors lt gt 2011 2015 KIRAMEK INC INSTALLATION TIPS Steps Toward a Professional Installation Ensure all electrical contacts cannot easily break by tugging on the wires If not using the 1480 s OBD plug cut off the plug and use the in cluded 4 PosiTap connectors RED to directly connect to vehicle s CAN amp Power wires or use an optional OB 22 or OB 23 splitter harness Use the included PosiLock connector DARK RED when connecting to the Siren For all other connections use solder if required and securely cover with electrical tape heat shrink tubing and or corrugated tubing Use only a DMM digital multi meter to test leads or take voltage read ings Do not use test lights or logic pro
30. oles and use self tapping screws Mount in a place that will not be splashed excessively with water or immersed in water 5 2011 2015 KIRAMEK INC Shock Sensor ES The shock sensor is not waterproof so only mount it inside the car Only use the included 2 sided tape and mount the sensor to the outside of a plastic surface such as the car s center console We recommend you mount it in open view rather than hide it in order to make sensitivity adjust ments easier When chosing a mounting location on the driver s side typically on the lower side of the center console plastics try to mount the sensor in a place where it cannot be accidentally kicked by the driver And before you mount the sensor with the included tape use your fingers to press against the place where you want to mount it to see if the plastics move a lot when you press on them Plastics that are looser will result in lower shock sensitiv ity Mounting on a more firm section of the car s plastic will result in much better sensitivity Since you only have one piece of included tape try to determine the best mounting location before you affix it NEVER use screws or wire ties to mount the sensor Always mount to plastic using the included tape Mounting to metal can increase sensitiv ity so high it will cause false triggering We strongly recommend you first clean the mounting surface in the car with brake cleaner or similar oil solvent degreas
31. ollowing 1 turn Ignition ON amp OFF then 2 Open amp Close any Door Upon seeing these events the system will Arm 20s after the last door is closed The doors will NOT be locked so you won t be locked out if you leave your keys in the car but the system will be Armed and will trigger if a door is opened 9 Siren Output 4 When set to Continuous default the system will feed a continuous 12v output to sound the included siren for 30s Full Trigger When set to Pulsed the system will feed a pulsed 12v 8A max output This can be used to create a unique siren sound with the included siren if you cut the Blue loop wire on the siren or used when connecting to the vehicle s horn by an optional relay VISION 1480 OWNER S GUIDE D ORI This feature automatically Rearms the system 60s after it is Disarmed unless a Door is opened or the Ignition goes ON during the 60s Doors will be locked when the system Rearms NOTE Many cars have a relock feature if you Unlock with your factory re mote the car will automatically relock the doors after some time has elapsed if no door has been opened If your car has auto relock and if the 1480 Arms on relock then you do not need to enable Auto Rearm s FOR 23 When set to ON the Doors will Auto Lock when the vehicle speed reaches 30km h 19mph And when you stop the car and put the gear back into the P Park position the Doors will Auto Unlock
32. on All product specifications and features are subject to change without notice 2011 2015 KIRAMEK INC PRECAUTIONS amp SAFETY OPERATION Use of the 1480 outside its intended purpose as described in this Install Guide and the 1480 Owner s Guide could result in damage to the vehicle or surrounding property or cause serious injury or even death As the installer of this security system it is your responsibility to ensure that the vehicle owner is properly informed of all the details of your instal lation which are pertinent to safety SAFETY POINTS TO ABIDE BY 1 Never start the vehicle s engine in enclosed spaces that lack adequate ventilation Extended exposure to carbon monoxide exhaust fumes can result in death Do not disconnect the vehicle s battery as it could cause serious prob lems with airbag systems anti theft radios or vehicle diagnostics If you absolutely must disconnect the vehicle s battery first disconnect the main power wiring harness of the 1480 and then disconnect the vehicle s battery Do not proceed with installing this system in vehicles that do not have a 12 volt electrical system This system will not function in 24 volt trucks and any damage resulting from such installation shall be the sole responsibility of the installer Do not install the 1480 control module or associated sensors in or near water or in a location where water could gather The 1480 is
33. on DO NOT install it yourself to save a little money at the risk of damaging your vehicle or causing physical injury J TABLE OF CONTENTS Precautions amp Safety 1 Installation TIPS iii esi less none a Ss 2 Technical Specifications 3 Included Items 4 ROO TES FISi 2528 nee E ends tra ares aa 5 System Wiring Diagram 6 OBD COMMOCHON dues gs mes arsed ade ware dala dearer a ogg grace 7 Power amp CAN Connections 9 Siren Connections 11 Siren Setup 4 54440savu se use he ee ade BORE a 12 Optional Connections 13 GWA OUTIDUT er cack m tis bis aden Weber dated eke 13 FO OGHIMOUT siria ear 13 CAN Signal Learning 14 Mounting System Components 15 Adjusting the Shock Sensor 17 TrOUDIBShNOONINY cessan 66 eat eee bea I a autre 58 18 OPTIONS sicilia nee mnt RES 20 l NOTE Consult Owner s Guide page 11 for Feature Programming NOTICE Although reasonable efforts have been taken to ensure accuracy in this Ana log Install Guide Kiramek Inc shall not be held liable for any errors omissions prop erty damage or injury resulting from the use of this informati
34. or move around excessively NOTE When considering an appropriate mounting location keep in mind that most thieves hot wire vehicles by removing the plastic panel just under the steering column Locations above or behind the glove box behind the radio or high up under the dash are all good mounting places However you may need to extend wires if your chosen location is too far from the steering column Jf you extend wires always use the same or larger gauge wire Solder all large gauge wire connections and cover with electrical tape or heat shrink tubing and or corrugate tube Mount the control module to a secure flat surface or use wire ties to affix to a factory wire harness The Status LED is used as a visual theft deterrent when the system is Armed and to alert the user if the siren triggered in their absence And both the LED and the Program Switch are used for feature programming This unit is the size of a factory switch cover so you can easily mount it with the included 2 sided tape somewhere near the steering wheel Mount it so the LED can be seen from outside the driver s side window Such will warn would be thieves and conveniently show you the Trigger Memory en g Find a location in the engine compartment such as the firewall that is far from heat sources or moving parts such as belts or the radiator fan Locate a factory bolt or bolt hole for securing the siren mount otherwise you will need to drill h
35. osen over time and result in system malfunction SYSTEM WIRING DIAGRAM Harness LED Program Switch Shock Sensor 12v Siren Output 2A GWA Output 500mA Ground Input Hood Switch Input 12v Power Input 1 Wire CAN HONDA NOTES 1 There are two BROWN wires Don t confuse them 2 Toyota and Nissan cars have an OBD2 connector that can connect alarm CAN amp POWER 4 wires Other cars allow POWER only from the OBD2 Yet other cars don t allow use of the OBD2 at all See pp 7 8 3 Some HONDA cars use 1 wire CAN In this case instead of using the BRN amp BRN RED wires you will only connect the GRN wire for CAN VISION 1480 INSTALL GUIDE OSD CONNECTOR An OBD2 connector is included with most 1480 systems and the following 4 wires are already connected to it gt 1 12v Power Input 2 Ground Input 8 CAN H 4 CAN L Toyota Lexus and some Nissan cars allow you to merely connect the OBD2 plug to your car s OBD2 connector and then you need only connect the BROWN wire to the Siren plus any optional connections see page 13 Other cars like Honda allow you to connect the OBD2 plug to your car in order to easily obtain 12v Power and Ground connections but the two CAN wires will need to be cut off from the OBD2 plug and connected manu ally using the included PosiTap connectors In addition some Honda cars use a 1 wir
36. revents the siren from triggering again And other car alarms that always trigger the siren when the Ig nition turns on offer no remote start or turbo timer compatibility at all IIP solves this problem by offering compatibility with Remote Start amp Turbo Timers with complete security How it works Normally if the Ignition is turned ON while in RSCM the system automatically bypasses the Sensor amp Ignition triggers but keeps Door Hood and Trunk triggers active But if the 1480 is triggered by a Door or Sensor before the Ignition is turned ON IIP automatically switches back to IG Protect Mode and the siren will be triggered if the Ignition is turned on Disarming and Arming again will revert to RSCM D 2011 2015 KIRAMEK INC AID x On compatible vehicles or on any vehicle when the op ni tional analog Hood input is connected the siren will blast for 30 seconds when the hood is opened while the system is Armed Vehicle hazard lights may also flash Al ERROR CHIRP Bazan If a Door or the Trunk is open when you Lock Arm you will hear 1 chirp only if Confirmation Chirps are ON followed by 2 chirps even if Confir mation Chirps are OFF The 2 chirps are Error Chirps that notify you the doors or the trunk will be bypassed because they are opened they won t trigger the siren Then 5s after you close the door s or trunk they can then trigger the siren if later opened You will only hear Error Chirps on cars that al
37. rive high current devices like the Horn S 114R or S 113 Pin switch to detect Hood opening OB 22 or OB 23 OBD splitter harnesses useful for simply hiding the 1480 s OBD connection OB 22 or hiding the connection AND adding a 3rd party OBD device 0B 23 Some 8rd party OBD devices may be incompatible with the 1480 Contact KIRAMEK for details Optional Sensors MMF 2 2 stage Radar Sensor e KST 24 2 stage Digital Tilt Sensor SB 03 Sensor Splitter to easily connect up to 3 sensors at once Luminator LED Scanners visual theft deterrents More details about add on devices can be found on our website www visionsecurity jp en DEAD VISION 1480 OWNER S GUIDE VISION products are engineered in Japan and manufactured in strict accordance with Japanese QC standards at an ISO9000 QS9000 certified factory www kiramek com 9 183 1 Itayama cho Handa shi Aichi Ken 475 0936 JAPAN TEL 81 569 20 5585 FAX 81 569 20 5586 EMAIL support kiramek com n DIGIOLINK SMART FACTORY KEYLESS UPGRADE SECURITY Installation Guide oe KIRANEK 2011 2015 KIRAMEK INC Aichi Japan Ver 1 7 AUG 2015 INSTALLERS READ THIS MANUAL THOROUGHLY The 1480 must be connected by an experienced VISION installer All product warranties im mediately become void if the 1480 is not in stalled by an authorized dealer If you acquired this product without profes sional installati
38. ry important Reconfirm what firmware is programmed in the 1480 control module If the firmware is not perfectly matched to your vehicle it doesn t matter if your wiring is perfect the alarm will not function until the right firmware is installed in the 1480 e Are you using the OBD connector on a car other than Toyota Nissan or Lexus If so it will not work At this time we do not support OBD con nections on cars other than Toyota Nissan and Lexus Ifall else fails try the following CAN LEARNING STEPS instead of those given on page 14 1 Disconnect the white 6 cavity connector of the Main Harness OR re move the Fuse on the Red 12v power line The objective is to kill power to the 1480 control module Wait about 10 seconds 2 Press and hold the Program Switch and at the same time reconnect the Main Harness or reinsert the Fuse You should now hear the siren blast and you will notice the LED is lit The 1480 has now been reset to its factory state 3 Release the Program Switch The siren will shut off but the LED will remain lit 4 Switch ON the Ignition The LED will turn OFF And the siren may or may not chirp 3 times 5 Switch OFF the Ignition The LED will light for 5 seconds turn off for 2 seconds and then it will flash 6 times The 6 LED flashes show the Manual Disarm code has been reset to 6 the factory default Vehicle CAN signals are now learned Wait 10 seconds before you begin testing 2011
39. shock sensor to avoid interference HOOD TRIGGERS SIREN BUT TRIGGER MEMORY REPORTS DOOR amp HOOD Some Mercedes and BMW cars send a digital door open mes sage on the CAN when the Hood is opened On these cars if the 1480 is Armed the siren will trigger when the Hood is opened even if the 1480 s Gray wire is not connected to an optional Hood pin switch But in this case Trigger Memory will report a Door Open trigger not a Hood trig ger However if you purchase an optional pin switch and connect the 1480 s Gray wire to it Hood triggers will then report as both a Hood and a Door trigger on the Status LED on some Mercedes and BMWs You may also see the Door and Hood icons on the LCD pager if you purchase the optional Paging System On cars where there is no digital CAN message sent when the Hood is opened a Hood open condition will not trigger the siren on those cars unless you purchase an optional Hood pin switch and connect the 1480 s gray wire to it In this case Trigger Memory and the LCD Pager will report only a Hood trigger via the Gray wire KES 2011 2015 KIRAMEK INC OPTIONS The 1480 can be installed in your car without the need for any Options However we do offer the following add on products to enhance security and convenience TR537S 2 way LCD RF Paging Control System ARIB T67 for Japan TR835S 2 way LCD RF Paging Control System FCC for USA 896H 1B Starter Kill Relay 896H 1CN Relay to d
40. strong earthquake jackham mer operation adjacent to the vehicle hurricane typhoon large explosions fireworks large animals ramming against the vehicle etc If any of these extreme cases are anticipated you can avoid false siren triggers simply by Arming the system with the Sensor Bypass Arming which ignores the shock sensor see page 3 of the Owner s Guide Another consideration is temperature The sensitivity can vary by as much as 20 under extreme temperature conditions You may wish to reduce the sensitivity in very hot weather and increase sensitivity in very cold weather Suspended Reflector Malfunction If the shock sensor is not working well or at all it may be that the suspend ed element inside the case was jolted out of position Disconnect the wire harness snap open the shock sensor case and adjust as shown below Correct Alignment Incorrect Alignment D VISION 1480 INSTALL GUIDE TROUBLESHOOTING CAN LEARNING NOT SUCCESSFUL If you manually connected Power and CAN pages 9 10 instead of us ing the OBD connector reconfirm all your connections If CAN H and CAN L are reversed you of course will not be able to learn the vehicle s CAN signals Also note that the vehicle s CAN wires are normally a twisted pair So if you connected CAN H and CAN L to wires that are not twisted you probably chose the wrong wires Reconfim that your vehicle is indeed compatible The make model and year is ve
41. t once per second while the system is Armed acting as a visual theft deterrent The LED turns off when the system is Disarmed unless there was a siren trigger TRIGGER MEMORY gd The LED flashes rapidly while the full siren blast is going off and Gy keeps flashing rapidly even after the siren stops When you Dis arm the Status LED will change its flashing pattern according to Table 1 below showing you what triggered the siren If the siren triggered more than once the LED will show you what caused the last 3 triggers Trigger Memory will displayed repeatedly on the LED until the Ignition is switched ON or until you Arm again TABLE 1 Status LED Trigger Memory LED Flashes What Triggered the Siren Trunk or back hatch Ignition 3 4 i Hood see Note below 6 7 i Sensor Full Trigger only There are no LED Flashes if the power is cut and then restored NOTE On most cars Hood triggers detected by CAN BUS actually report as Door triggers If you want Hood triggers to always report as Hood trig gers on the Status LED and on the Optional LCD Paging System you will need to purchase an optional Hood Pin Switch and have it installed in the engine compartment see the Install Guide for more info Also see the bottom entry on page 15 for more details about Hood trigger reporting VISION 1480 OWNER S GUIDE ee For cars that support it via CAN BUS vehicle Hazard lights will flash
42. the white 6 cavity connector of the Main Harness OR remove the Fuse on the Red 12v power line The objective is to kill power to the 1480 control module Wait about 10 seconds 2 Switch ON the Ignition 3 Press and hold the Program Switch and at the same time reconnect the Main Harness or reinsert the Fuse You should now hear the siren blast and you will notice the LED is lit The 1480 has now been reset to its fac tory state 4 Release the Program Switch The siren will shut off and the LED will turn off And the siren may or may not chirp 3 times 5 Switch OFF the Ignition The LED may or may not stay lit and or flash a few seconds 6 Lock and Unlock Vehicle CAN signals are now learned Wait 20 seconds before you Lock again otherwise you may enter Sensor Bypass Mode see pg 8 in the Owner s Guide for details of that mode NOTE If the above steps do not work i e the 1480 won t function you may need to start the engine in Step 2 above rather than just switch the Ignition ON This issue occurs only on some Hybrid cars 2011 2015 KIRAMEK INC MOUNTING SYSTEM COMPONENTS Control Module The Control Module is the brain of the system and therefore must be installed in a secure location under the dash NEVER install the Control Module in the engine compartment or near any source of heat or moisture NEVER place the Control Module near moving parts or in a location where it can vibrate
43. ur combined devices attached to the GWA wire exceed 500mA On NO BATTERY FIG 4 Connecting LED Scanners Optional LED Scanner Hood Input OPTIONAL PARTS REQUIRED Hood presses down on this point when closed An optional Hood Switch al lows more accurate reporting Vehicle Body Metal Lt of Hood triggers on the Status ngerad LED and optional Paging Sys tem Connection is shown in Ci Switch Fig 5 at right Contact Washer Optional Hood Switch 7 D S 113 or S 114R See pages 9 amp 15 in the Owner s p n or Guide for more information Nut ju FIG 5 Optional Hood Pin Switch Installation gt VISION 1480 INSTALL GUIDE CAN SIGNAL LEARNING This required procedure verifies that the firmware inside the 1480 is truly matched to your car The 1480 will be completely disabled until you com plete the steps below You only need to do it once NOTE Performing this initial setup procedure automatically resets all func tions to their factory defaults This includes a reset of the Program mable Features Owner s Guide page 11 and resets any custom Manual Disarm Code you may have programmed Owner s Guide page 5 If you have the optional Paging System installed p n TR537S or TR835S all pagers will be erased from memory and you will have to relearn them And if you have performed this CAN Learning procedure before any previously learned CAN signals will be overwritten 1 Disconnect
44. ut Blue Loop for 6 tone sound Dark Red PosiLock FIG 2 1480B Siren Connections Cut Blue Loop for 6 tone sound NOTE One PosiLock connector is included for connecting the 1480 s Brown Siren Output If you use the included OBD for Power amp CAN you will have 4 PosiTap connectors left over Although you can use one or two of these to easily connect the other siren wires shown above we suggest a direct connection to the car s battery And although it s easy to connect Ground to a bolt in the siren s metal mount keep in mind that rust could result in a faulty Ground in the future lt i gt 2011 2015 KIRAMEK INC SIREN SETUP NOTE We suggest you avoid connecting the siren s RED or BLACK wires in parallel with the Power amp Ground wires of the 1480 If you splice Pow er Ground off the OBD plug it may cause a voltage drop malfunction in the alarm system Even though it s troublesome we recommend a direct connection to the car s battery LOCATION Unlike the 1480 control module and sensors the siren is to be mounted within the engine compartment That means you must run a wire through a rubber grommet in the firewall to connect the 1480 control module s Brown Siren Output wire to the siren Avoid mounting the siren in places where water can pool or constantly fall on the siren BACKUP SIREN KEYS RED dot The 1480B comes with a Battery Backup Siren and two GRN dot siren keys At
Download Pdf Manuals
Related Search