Finger Vein Access Control dvice Quick Start Guide
Contents
1. PIN Slot Color Power Output 12V Red Ground Black Wiegand Input White Wiegand Input Green Wiegand Output Blue Wiegand Output Yellow Wiegand Input the device is featured with Wiegand signal input function to connect to card reader or standalone device Wiegand Output the device is featured with standard Wiegand signal output function and can be used as reader The wiring distance between device to controller should not exceed 5m if longer connection distance or connection with strong interference are necessary please adopt Wiegand signal exteneder 9 Finger Vein amp Fingerprint Registration and Verification Modes Note In finger vein registration process the fingerprint of the selected finger is also registered 1 Suggested finger first finger middle finger 2 Finger Placement Position In order to read your fingerprint and finger vein data touch the front side of finger vein reader with Neseceisseesce p gt Fingerprint Reader Finger Vein Reader fingertip Finger Guide The device starts aii collecting data once the a T P Touch Sensor finger root touches the finger vein reader a x S D N 3 Verification Steps Place the finger according to the finger guide Finger tip must touch the front of finger vein reader in order to properly collect fingerprint and finger vein images e Touch the front side2. Finger Vein Access Control dvice Quick Start Guide Version 1 0 Date June 2015 1 Overview Fingerprint amp Finger Vein Device Front Left Side Hl Touch screen pareen P card reader USBslot lt q eee eee eee ne P Doorbell Reset button Press the button p fingerprint reader with sharp headed tool with less P Finger vein reader than 2mm in diameter after 30 P Finger vein sensor During second powering on to reset registration after finger device touches the sensor device begins collecting and verifying D Finger Vein Device fingerprint and finger vein Front p Touch screen M e E PCard reader Reset button Press the button with gt Doorbell sharp headed tool with less than 2 mm in diameter after 30 second Fingervein reader powering on to reset device P Finger vein sensor During registration after finger touches the sensor device begins collecting and verifying finger vein Power Input Back Ethernet Wiegand RS485 Output Tamper Auxiliary p Alarm lt q Fie Input Alarm Switch S Open Close Z door button O Shut down the power during installation EMF generated when the lock is turned 2 12V 3A power supply is recommended ON OFF Do not install the device in a place subject Q Please properly set fingerprint and finger to direct sunlight or humidity vein verific
3. Slot Color Power Input 12V Red Ground GND Black 12V DC GND The operation power of the device shall be DC12V the current shall be 3A 6 Connection to Computer softwares via Ethernet Connection between device and computer Access control software via Ethernet Shown as below IP Address 192 168 1 201 Subnet Mask 255 255 255 0 68 OC 7 Connection to Doorbell Door Sensor Open Close Door Button Alarm amp Siren etc IP Address 192 168 1 39 Subnet Mask 255 255 255 0 f I PIN Slot Color 1 Auxiliary Input AUX Brown i i E a a 2 Ground GND Purple jii is 3 Doorbell BELL Green Me l IRE 4 Doorbell BELL Orange Het o o AH 5 Door Sensor SEN Yellow Wamms f 9 6 Ground GND Red tg Power De oe BUT Pue Normal Open NO1 White wr Siren 9 Common COM1 black Door aa 10 Normal Closed NC1 Grey Sensor 11 Alarm AL Black 12 Alarm AL Red BELL lt x aya x lt t U a Device can be connected via Auxiliary and emergency switch Open Close af Input Slot with output switch signal sensors A Door Button Power f Bower 0 including siren gas detector infrared detector 3P Doo Alarm 1 rbell 8 Wiegand Input Output Wiring Instruction
4. ation mode before registering 4 Please follow the connector instruction for users Requirement varies with different wiring verification modes 5 Under serious electrostatic environment Fingerprint amp Finger Vein Mode Both please connect the GND before other fingerprint and finger vein must be verified wirings in order to prevent static electricity to access from damaging the device Fingerprint or Finger Vein Mode Only 6 Itis necessary to connect the FR107 diodes fingerprint or finger vein is required to be in parallel to the positive and negative poles verified to access of the electrical lock so as to release the the functions mentioned with are only self inductance featured with particular models of device 3 Installation on Wall Insert cables to connectors before installation Put the mounting template sticker ontothe Install the device onto the back wall and drill holes according to the symbols plate Fix the back plate onto the wall 4 Fix the device with locking screws onto ate Nas ae Note For user heights between 150CM to 170CM it is recommended to install the device at 140CM above ground may be modified according to user average height 4 Access Control System Diagram f C jd Alarm lt q Gece mee q L Open Close door button Server Door Sensor Door 5 Power Connection
5. ed to Admin Users are only allowed to be verified by finger vein fingerprint card or password while Admins are authorized to enter Main Menu apart from normal verification functions FV amp FP to register finger vein and fingerprint Suggested to register first finger and middle finger See 9 Finger Vein amp Fingerprint Registration and Verification Modes for reference Badge Number to register card no Password to register user password 1 8 digits Access Control Role to set users access control authority 15 User Verification Note the device is by default set as Fingerprint amp Finger Vein Mode and can be modified to Fingerprint or Finger Vein Mode See 7 3 Finger Vein amp Fingerprint Parameters Setting in Access Control Finger Vein Series User Manual Fingerprint amp Finger Vein Mode Fingerprint Finger Vein verification to success Fingerprint or Finger Vein Mode Fingerprint or Finger Vein verification to success 1531 20 kr gt Finger Vein amp Fingerprint Verification Place and press finger on the reader properly Successfully verified appears upon successful verification J gt Card Verification Swipe card in swiping area Successfully verified appears upon successful verification gt Password Verification Enter User ID and click OK then select pass verification mode shown in 4 Q Enter password and click OK Successfully verified appears u
6. etting To set Access Log parameters according to personal needs FV amp FP Parameters To set finger vein parameters according to personal needs Reset To reset device and system to factory settings USB Upgrade To upgrade device s firmware program through Upgrade documents in USB Note User messages and settings of Access Control interface are not deleted after being reset to factory setting 13 Access Control Management Click Access Control in Main Menu to enter Access Control Management interface Users can open locks only upon these requirements are met 1 The access time should fall into either the use s individual time zone or group time zone 2 User s group must be in the access combo when there are other groups in the same access combo verification of members of those groups is also required to unlock the door Access Control Options To set Locks and related devices parameters Time Rule Setting To set maximum 50 time rules Each time rules consists of 7 spaces each space consists of 3 time slots Holidays to set holiday access control and access time Combined Verification To set access control combinations A combination consist of maximum 5 access control groups Anti passback Setup To prevent passing back which causes risks to security Once enabled entry and exit records must be matched in order to open door Entry anti passback exit passback and entry amp exit anti passback f
7. of finger vein reader with fingertip then press your finger upon the finger vein reader Improper positioning of finger will Touch the reader with finger root affect the proper collection of C fingerprint and finger vein images DSO TILOISSA P N The device starts collecting data once the finger root touches the finger vein reader Reifidve finger C after beep sound appears J Maintain the natural hand gesture Do not bend your fingers Do not exert finger to press the reader In the initial interface click Menu icon EH to enter Main Menu Click Scrollicon to scroll down to display full menu Click Scroll icon M again to scroll up Welcome 11 Ethernet Setting In the Main Menu Click Comm gt Ethernet to enter Ethernet Setting IP Address the default IP address is 192 168 1 201 Subnet Mask the default subnet mask is 255 255 255 0 Gateway the default gateway is0 0 0 0 DNS the default DNS address is 0 0 0 0 TCP COMM Port the default port is 4370 DHCP Dynamic Host Configuration Protocol which is to dynamically allocate IP addresses for client via server If DHCP is enabled IP cannot be set manually op Display in Status Bar To enable or disable displaying Network Connection Icon in Status Bar ia 12 System Setting Click System in Main Menu to enter System Setting Date Time To set date amp time Access Logs S
8. pon successful verification 16 DataManagement In Main Menu interface click Data Mgt to enter Data Management interface Delete Data to manage device data including deleting all data deleting all management authorities deleting all promotional display and resetting to factory setting Backup Data to back up device operation data and related data to computer or Hard Drive Restore Data to restore data saved in Computer or Hard Drive to the device Please refer to Access Control Finger Vein Seires User Manual 17 Obtain Access Control Report Connect device to network Begin access control device operation e g Access3 5 Add device to the access control software to obtain device data and event logs check access control events and generate reports Note Please refer to the attached Access3 5 Access Control Management System User Manual CD 18 Troubleshooting Invalid time zone is displayed after verification Contact Administrator to check ifthe user has the privilege to gain access within that time zone vVerification succeeds but the user cannot gain access Check whether the user privilege is set correctly Check whether the lock wiring is correct The Tamper Alarm rings To cancel the triggered alarm mode carefully inspect whether the device is properly installed and reinstall the device properly if necessary
9. unctions are available J Access Control Combination Setting Note You may choose not to user Access3 5 Software and to set access control combinations directly in device when using the device for the first time 2 If you use Access3 5 Software to set Access Control Combination of the device you are then not allowed to set access control combinations directly in device E g Add an access control combination which required 2 persons verification from both group 1 set in User Management and group 2 1 In Combined Verification List click the desired combination to modify and enter the interface shown in 1 2 Click to ascend click to descend to set user group no and click Confirm to save and back to Combined Verification 6 Note A single Access Control Combination can consist of maximum 5 user groups in order to open door both 5 users verifications are required ifthe combination is set as shown in 3 a user from group 2 must obtain verifications of 2 users from group 1 in order to open door Set all group no to zero to reset access control combination 14 Add Users In Main Menu interface click User Mgt gt New User to enter New User User ID to insert user ID 1 9 digits Name to set username 1 24 chcaractes a Chinese character equals two characters User Role to set user s authority Users are default set as ordinary users and can be modifi
Download Pdf Manuals
Related Search