Midland BT Intercom manual
Contents
1. 2 4 GHz ISM band and using spread spectrum modulation techniques Part 2 Harmonized EN covering essential re uirements under article 3 2 of the R amp TTE Directive Supplementary information to the conformity assessment result on which the declaration is based Conformity assessment procedures are referred to art 10 4 linked with Annex III of Directive 1999 5 ec The test sample fulfils the requirements specified above on the basis of test result and their evaluation The product herewith complies with the essential requirements of EC Directive 99 05 EC 89 336 EEC 92 31 EEC 93 68 EEC 73 23 EEC 93 97 EEC Reference to any marking or other indication e g on the product is exhibited in attachment to this declaration Reggio Emilia 27 06 06 CTE International srl Quality Assurance Manager Peterlini Stefano i TAALA This document is owned by Cte International srl It is forbidden to reproduce or diffuse it without the authorisation of the Quality Assurance Mana er of CTE International srl ENGLISH Device for the passenger Intercom always on The intercom function can be activated by voice Vox or also manually simply short pressing the Control button from the passenger unit If the intercom is manually activated the communication between the driver and the passenger is always open Shortly press the Control button to activate the intercom permanently A single beep sound will confirm it Shortly press again the Cont2. distance between the headset and the mobile phone must be within 10 meters 3 With the unit turned off press and hold the CTRL button until the blue and red LEDs begin alternating rapidly 4 On your phone search for Bluetooth devices by following your phone s instructions Usually this is done by selecting the Search or Discover option in the Bluetooth or Connection menu 5 After a few seconds of searching your phone will list the Midland BT as a discovered device Select it and follow your phone s instructions to accept pairing 6 When prompted by your phone enter 0000 4 zeros as your PIN or passkey 7 Your phone will confir that pairing has succeeded If pairing is not completed within 2 minutes the driver unit will return to stand by mode flashin blue every 3 seconds To pair again turn off the driver unit by pressing the CTRL button until the red LED flashe 3 times and repeat the process as indicated above Reconnecting the driver unit to a paired phone Although you may have previously paired your unit to your phone each time you turn one of them off some phones require that you re establish the connection Reconnecting may also be necessary when your headset and phone have lost the radio signal because the distance between them has exceeded 10 meters After you have turned on your mobile phone there are several methods to re establish the connection In most cases turning on the driver unit reconn
3. Midland BIintercom Bluetooth Bluetooth Headset CARDO MIDLAND BT INTERCOM Instruction guide Thanks for purchasing the Midland BT Intercom In this guide you will fin all the information you may need to get the best performances from this device The package contains e two devices one for the driver one for the passenger e 2clamps for helmet fixin e 1 wall charger with 2 plugs e mounting kit allen wrench velcro and extension pads Device for the driver The dark blue logo indicates the Bluetooth device for the driver It allows the connection with a Bluetooth mobile phone or with the passenger as an intercom system Device for the passenger It is recognised by the light blue logo It contains an intercom module which allows the communication between the driver and passenger Attention this is only a suggestion The driver device complete with both Bluetooth and Intercom modules can be attached to the passenger s helmet as well In that case the passenger will be able to receive phone calls Make sure both units are fully charged prior to initial use Allow al least 4 5 hours for a full charge before using for the firs time The two devices Driver and Passenger are ready to be used like intercom no pairing process is needed just fi it on the helmet and Start talking Only if you need to use the cellular phone with the Driver unit the pairing process is needed ref
4. To turn on the headset hold the CTRL button down for about 6 seconds until the blue LED flashe three times and an ascending alert tone is heard Then release the button To turn off the headset hold the CTRL button down for about 3 seconds until the red LED flashe three times and a descending alert tone is heard Pairing process The pairing process allows the units to identify each other Pairing the driver passenger units for Intercom This process is not normally neaded because the two devices included in the same packing are already paired and the Intercom function is already enabled The pairing process may be needed in case of units coming from different packaging To pair the units e Make sure that both unit are turned ON and within a range of one meter you can make this procedure with the units detached from the helmet s clamp e Simultaneously press the Intercom buttons of both devices until the red indicator light of the passenger will light steady If successful the red light of the passenger unit will turn to blue light steady for some seconds and then flash If paring has failed the red light of the passenger will turn off without change to blue Pairing the mobile phone The driver unit can be paired to a Bluetooth mobile phone in order to make receive phone calls Follow the procedure below to pair the driver unit to a Bluetooth mobile phone 1 Turn on the phone and activate its Bluetooth function 2 The
5. assenger Control button DO 7 1 4 4 i 1 T Rev za Authorised on 14 11 2005 EC Certificate of Conformity By 5 Peterlini The World in Communication Cte intematonal to Ec Directive 99 5 89 336 93 68 73 23 CE DECLARATION OF CONFORMITY N 06062701 Manufacturer C T E International S r l Address Via Sevardi 7 Zona Industriale Mancasale 42010 Reggio Emilia Produce Nam BT INTERCOM Product Type Bluetooth Intercom Headset Brand MIDLAND The product described above is in conformity with the following Specifications based on sample testing poet an At ih th tht eh ee 0 Tite Edition 99 05 CE pd 3 18 information technology i equipment Safety 2001 Part 1 General requirements 3 1b Electromagnetic compatibility and Radio spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements i EN 301 489 03 Electromagnetic compatibility and Radio spectrum Matters ERM V1 4 1 ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 3 Specific conditions for Short Range Devices SRD operating on frequencies between 9 kHz and 40 GHz 3 2 EN 300 328 2 Electromagnetic compatibility and Radio Spectrum Matters ERM V1 6 1 Wideband Transmission systems Data transmission equipment operating in the
6. d Make some tests in order to find the optimal condition With the Voice Recognition feature disabled you can answer the incoming call only pressing the CTRL button Attention The Voice Recognition enable disable feature effect only the phone call answering and not the Intercom function Volume control Midland BT Intercom comes equipped with AGC technology to automatically adjust the speaker volume to the optimal level based on ambient noise and driving speed You may manually adjust the volume by pressing the volume buttons one step at a time For each volume step you adjust you will hear a short beep The AGC function for automatic volume adjustment has the priority over manual volume setting Volume Volume press to decrease the press to increase the volume volume I 2 Z TI LIGHT AND SOUND SIGNALS DRIVER S UNIT LED indication 9 lt None Single red las 35 5 Single red flas every 3 seconds Low battery while in stand by Intercom activation mode 2 tone enable by VOX 1 tone intercom always on DRIVER FUNCTIONS MOBILE PHONE if you want to Turn on the unit Turn off the unit Answer a Call Reject a call Terminate a call Increase the volume Decrease the volume Voice Dial Redial INTERCOM If you want to Start using th
7. e Intercom Stop using the Intercom Conversation among passenger driver and the other party Release the extended conversation above PASSENGER FUNCTIONS INTERCOM If you want to Turn on the unit Turn off the unit Start using the Intercom Stop using the Intercom Increase the volume Decrease the volume Intercom communication always on Intercom communication enabled by VOX do this Press the Control button for 6 seconds at least Press the Control button for 3 seconds at least Short press of the Control button say a word Short press the Intercom Button remain silent for 15 seconds I 2 al Z TI Long press the Intercom Button Short press of the Volume Up control Short press of the Volume Down control In stand by mode press quickly the Control button and state the name of the person to call In stand by mode long pressure of the Intercom button do this Start talking Stop talking after 15 secs you will return to stand by mode During a phone call short pressure of the Intercom button Short pressure of the Intercom button do this Press the Control button for 3 seconds at least Press the Control button for 3 seconds at least Start talking Stop talking after 15 secs you will return to stand by mode Short pressure of the Volume Up control Short pressure of the Volume Down control In standby mode short press on the Passenger Control button In standby mode short press on the P
8. ects it automatically to the phone e With some mobile phones you need to re establish the link to your headset by using your phone s menu Please refer to your mobile phone s manual for operating instructions e Assuming your mobile phone features voice activation tap the CTRL button on your BT INTERCOM This will activate your voice dial function on the phone indicating that the connection is established e Do nothing Once a call is received answer by tapping the CTRL control Intercom function The activation of the Intercom function is very simple with both units switched on the driver or the passenger start talking with the other party To stop using the intercom and return to standby mode lower current consumption stop talking on both sides and the intercom will turn to standby mode automatically after 15 seconds When it turns to standby mode you will then hear 2 beeps The Intercom function uses the AGC technology that automatically increases the volume according to the background noise Therefore it may happen that if you try the Midland BT Intercom inside a silent and close environment the volume is low but it will increase while you are on the move on your motorbike Intercom always on The intercom function can be activated by voice Vox or also manually simply short pressing the Control button from the passenger unit If the intercom is manually activated the communication between the driver and the pas
9. er to chapter Pairing process for further information The Intercom function uses the AGC technology that automatically increases the volume according to the background noise Therefore it may happen that if you try the Midland BT Intercom inside a silent and close environment the volume is low but it will increase while you are on the move on your motorbike If the Driver unit is paired to a cellular phone just remember that the voice recognition answer to incoming call is enabled by default refer to chapter Voice recognition VR for further information Technical specificatio MECI OEI scrngotsesiracsetitasiasteanctesaecuraintatnssimacsaditan Bluetooth ver 1 2 Maximum distance between driver passenger about 10m Battery life in conversation sa ss mn neta aa ea a taia pa about 7h Battery life in stand by seca a a a ceata aaa aaa about one week Charging WINE i rata ai a aaa about 4 5h IMPORTANT MIDLAND BT Intercom is a water resistant device designed for safe use under rainy conditions However the headset is not totally waterproof and it is not recommended under heavy rain conditions In any event the silicone cover protecting the charging jack should always be tightly closed I 2 al Z TI Detailed view of the BT Intercom Communication units Buttons The buttons on the communication units lets you enable the functions of the Bluetoo
10. hortly the Intercom button to add the passenger to the conversation At the end of the call this feature is automatically deactivates I 2 Z TI If the driver wants to exclude the passenger before finishing the conversation he will shortly press again the Intercom button of his device Handling calls only from the driver unit Certain advanced features of Midland BT Intercom are accessible to phones equipped with the hands free profile Check your phone s manual to find out if it supports this kind of profile Initiating calls from the phone s keypad a Dial the phone number on the keypad of your phone b Press Talk or Send on your phone to dial the number Voice dialling Make sure your phone is on but no call is in progress Tap the CTRL button and listen for a tone Now pronounce the name of the party you want to call and wait for feeback from the phone The type of feedback depends on your phone The best performances of this function will depend on the type of helmet you use close or open and on the speed Make some tests in order to find the optimal condition Answering calls The ring tone volume for incoming calls increases gradually When you hear the ring tone on the headset there are 2 ways to answer the Call e Short press the CTRL button on your headset once e Say loudly any word of your choice e g Yes or Answer If you do not utter any word wi
11. rol button to activate the intercom by voice VOX Two beeps sound will confirm it The Intercom is factory preset in voice activation VOX mode The manual activation always on can be done only from the passenger unit If the passenger unit is switched off or the intercom communication is closed by an incoming phone call on the Driver unit the intercom activation is switched back to the voice activation mode To activate again the permanent mode shortly press the Control button on the passenger unit ATTENTION The pilot and passenger devices must be paired Please refer to the dedicated section on page 4 of the BT INTERCOM user manual CTRL button MIDLAND BT INTERCOM MipLaND
12. senger is always open Shortly press one time the Control button to activate the intercom by voice VOX Two beeps sound will confir it e Shortly press again the Control button to activate the intercom permanently A single beep sound will confir it The Intercom is factory preset in voice activation VOX mode The manual activation always on can be done only from the passenger unit If the passenger unit is switched off or the intercom communica tion is closed by an incoming phone call on the Driver unit the intercom activation is switched back to the voice activation mode To activate again the permanent mode shortly press the Control button on the passenger unit Answering a call when Intercom is active When the mobile phone rings for incoming call the Intercom will be switched to stand by mode To answer the phone call it is sufficien to pronounce a word or alternatively press the CTRL button In case you don t want to answer remain silent until the phone stops ringing At the end of the phone call the Intercom will be automatically reactivated On some phones you will have to wait up to 15 seconds after call termination before you can return using the intercom again To activate the conversation between driver passenger and another party During a phone call the Intercom is automatically disabled but the driver can decided to include the passenger in the phone call conversation On the driver unit press s
13. sion pad I 2 Z TI The microphone must be placed in a vertical not horizontal position in front of your mouth with the yellow mark towards you It can also be slightly adjusted to suit your helmet Make some tests to fin optimal Picture 1 Picture 2 position e Once you have identifie the ideal position for microphone and speaker use the Allen Wrench to fasten the clamp e Now slide the headset downwards along the sliding panel of the clamp Picture 4 until a sotf clicking sound indicates that the headset is properly locked into place back plate e Before fastening the screws make sure to adjust the clamp s Picture 4 location to an ideal position i e to the spot where the attached speaker sits opposite your ear and the microphone is located in front of your mouth Picture 3 You may need to re position the clamp repeatedly until you identify the ideal spot The speaker can be easily placed into position and removed by means of the supplied velcro layer that attaches to the inner padding of you helmet Attention Be sure that the microphone is correctly positioned the yellow mark on the mike must be towards your mouth Removing the communication unit from your helmet e To remove the unit from the clamp press gently your finge against the arched tip of the back plate and use the other hand to slide the headset upwards along the sliding panel Picture 5 Picture 5 Switching on and off
14. th and Intercom They can be activated in two different modes e Short pressure push the button less than one second e Longer pressure push the button for more than 3 seconds CTRL button Intercom button Volume Volume Charging socket Fixing plate with microphone and speaker Microphone back plate of the clamp press on arc to release the headset unit Sliding plate of the clamp Earphone Charging batteries Make sure that both units are fully charged prior to initial use Allow at least 4 5 hours for a full charge before using for the first time Normally 3 4 hours will suffice for complete charge Charge the units by inserting the wall charger into the charging socket lift the rubber cover to insert the plug The red LED on the BT Intercom will turn on when charging begins Allow the headset to charge until the red LED turns off e When the charge is complete release the headset from the charger Attaching and removing the BT Intercom from your Picture 3 helmet Installation The installation is very simple e The clamp serves as the base for the communication units and must be attached to your helmet before using the device e Use the enclosed Allen Wrench to loosen the 2 screws of the clamp Picture 1 Then slide the back plate of the clamp between the internal padding and the external shell of the helmet Picture 2 In case the external shell of the helmet is too thick use the optional exten
15. thin 15 seconds after hearing the first ring tone the call will be automatically rejected and the headset will stop ringing Press here to answer the call Terminating calls To end a call keep pressed the Intercom button of the driver device for some seconds a beep tone will confirm the termination If the other party terminates the call first you don t have to do anything Long press here to terminate the call Phones without handsfree protocol require pressing CTRL button to terminate the calls Call reject While you hear the ring tone on the headset there are two ways you can reject the call e Press the Intercom button on your headset e Remain silent for 15 seconds Press here to reject the call or initiate redial Redial While the Intercom is in stand by long press the Intercom button on your headset to redial the last number Voice recognition VR The VR feature voice recognition allows you to answer or reject incoming calls by voice control without having to remove your hands from the handlebars By default this feature is enabled To deactivate this function keep pressed simultaneously the Up and Down volume for 3 seconds You will hear two beep tone confirming the deactivation of the function To activate it again follow the same procedure you will hear one beep tone The best performances of this function will depend on the type of helmet you use close or open and on the spee
Download Pdf Manuals
Related Search