PT600X User Manual
Contents
1. Resolution Check if wiring connection is in order Recharge battery Resolution www bofan cc If your APN doesn t have username and password type APN only Please get the correct APN of SIM card in tracker from your SIM card provider Domain the tracking platform domain name Port 8600 fixed for PT600X GTI GPRS Time Interval Time Interval 0 to turn off this function Time Interval 5 65535 unit second Distant Interval O to turn off this function Distant Interval 100 65535 unit meter suggest Distant Interval gt 500 Angle 0 to turn off this function Angle 15 360 unit degree suggest Angle gt 30 Move Ratio 0 to turn off this function Move Ratio 1 only integer ACC Ratio 0 to turn off this function ACC Ratio 1 only integer NOT suggest use all Distant Interval and Angle and Move Ratio and ACC Ratio if you don t have special needs Make PT600X in good GSM network coverage Connect power cable to car battery directly or use 12V charger to charge it for 3hours at least Wait for SMS Sometimes GSM network slows down during peak time or base has problem Write correct password or SMS format BOFAN format The SIM in PT600X runs out of credit No SIM card SIM card has expired SIM has PIN code set SIM is warped or damaged Roaming not enabled Problem Reply SMS starts with Last Possible Cause PT600X does not have clear view of the sky PT600X is ind2. Ignition Detection Input 4 Input 4 Ignition BOFAN 3 Detecting Lock Status of Car s Door or Trunk Car Boot Locked or Unlocked Input 5 www bofan cc Power positive 1 2v 24v Status Lock Input 5 Power negative Output 1 4 Connecting with Sensors such as weight sensor Input 2 Input3 gt Input 2 Input 3 Weight Sensor 12v 24v For Output Ports 1 Engine Cut optional Relay s connection on PT6 00X car battery s positive wire connect to this F white and red wire ai Cut the oil pump power cord connect it to two green wires Output Any one of yellow output wires on PT600X is ok After you 9 BOFAN connect relay according to above picture correctly you can send following SMS commands to stop car or restore the circuit Stop Car 0000000PC1 1 Restore circuit 0000000OPC1 0 www bofan cc Notes if you connect output2 to relay yellow wires then you need to send QOOOOO0OOPC2 1 command to stop car g Please don t use this feature while car vehicle with high speed driving and we suggest connect relay with fuel control line in your car Bofan is not liable for any traffic accidents 2 Connecting with alarm siren optional 12v 24v Alarm Output 2 If you want to speed alarm or geo fence alarm trigger this siren to have locale alarm please refer to AN and SAL command in SMS Command List Or connect your sales representative to
3. AD2 wire PT600X will send Temp High alarm SMS to SOS number when tracker get AD2 data gt 30 but this alarm is effective only when input4 on if you connect input4 to car ignition then it means car ignition on Notes if your temperature sensor work independently and don t depend on car ignition then you don t need to set index3 as input4 here B 18 BOFAN Set Analog Voltage lt password gt AV lt AD Port gt lt min voltage of sensor gt lt max voltage of sensor gt 24 If your analog sensor max voltage is not 6V then you need to do this setting to let tracker know what is your sensor voltage specification Shake Alarm lt password gt SKA lt index gt or Move Alarm PT600X with built in motion sensor to support this function Define motion sensor sensitivity lt password gt MSS lt value gt Set char for alert SMS contents lt password gt ACH lt Alarm gt lt Char gt For example 000000ACHIN4Engine Start www bofan cc AV Analog Voltage AD Port 1 means AD 2 means AD2 3 means AD3 4 means AD4 Min voltage of sensor input your sensor min voltage at here Max voltage of sensor input your sensor max voltage at here it can t be over the max voltage of tracker support SKA Shake Alarm Index 1 to send shake alarm SMS to SOS number when PT600X shakes 0 not to send shake alarm SMS to SOS number when PT600X shakes MSS Motion Sensor Sensitivity Value number range is 1 15 Default set OOOOOO
4. Get Google map link by SMS request Set password Reset password when the previous password is forgotten Set preset phone number for SOS button Command lt password gt VER lt password gt RCP lt password gt TEL lt password gt TEM2 lt password gt TEN lt password gt TEM1 lt password gt RCA lt password gt RCM lt password gt PWD lt new password gt 000000RPW lt new password gt lt password gt SOS lt SOSNumber1 gt lt SOSNu mber2 gt lt SOSNumber3 gt www bofan cc Remarks VER Version RCP Request Current Position Get current location s latitude and longitude of PT600X PT600X SIM card will call your mobile phone after you send the command once you answer the phone two way communication begins If you want to save credit of SIM card number in PT600X you can send this command then dial out from your mobile phone to PT600X s SIM card number for two way communication PT600X SIM card will call your mobile after you send the command to PT600X you can answer this call and start to listen the voice around PT600X If you want to save credit of SIM card number in PT600X you can send this command to PT600 later call PT600X s SIM card number from your phone to monitor voice RCA Request Current Address Note this command is only valid when tracker is connecting to server by GPRS successfully and GPRS signal under stable status RCM Request Current Map this command is still v
5. PT600X does not connect to server successfully after making GPRS communication settings PT600X connects to server successfully after making GPRS communication settings PT600X is connected with external power source PT600X is not connected with external power source but has sufficient power PT600X is not connected with external power source and has no sufficient power No power please charge immediately 9 BOFAN 4 Start Tracking You can start to track your car or test the tracker after GSM and GPS light work normally There are two ways to track the car one is by www bofan cc SMS on mobile basically and the other one is via GPRS on LiveGTS software platform 4 1 Tracking by SMS on mobile Tracker replies SMS with coordinates When you want to know the PT600X location you can call the SIM card number in PT600X or send a SMS command to PT600X from your mobile and after some seconds it will reply a SMS with the position Lat amp Log data to your mobile To get position by calling a Call the SIM card number in PT600X from your mobile phone b PT600X will hang up automatically after several rings then replies a position SMS to your mobile phone Notes if you don t like the tracker reply a message after calling you can send command 0000000OPT0 to close this function if you want to restore this function later you can send command 0000000OPT1 to activate this function again To get position by SMS command SMS Com
6. alarms please refere to below example details for ignition on off alarm lt password gt SAL lt Alarm type gt lt Index1 gt lt Index2 gt lt Index3 gt lt Index4 gt lt Index5 gt www bofan cc Index4 OPC2 0 means close output2 OPC3 0 means close output3 TEL13012345678 means trigger this TEL command to call 13012345678 any other command can be done at here SAL Set Alarm Alarm type IN1 for input1 IN2 for input2 IN3 for input3 IN4 for input4 IN5 for input5 SPD for over speed alarm GEO for geo fence alarm MLA for Mileage Alarm SKA for shake alarm LPA for low power alarm IU1 for input up IU2 for input2 up IU3 for input3 up IU4 for input4 up IU5 for input5 up any alarm command Index1 1 to alert on platform 0 do not alert on platform Index2 1 to send alert SMS 0 do not send alert SMS Index3 1 to call the preset SOS phone number 0 do not call the preset SOS phone number Index4 1 to take photo 0 do not take photo Index5 Action No if you want to trigger above 2nd alarm action then input 2 at Index5 at here Default set OOOOO0OSALIN11110 OOOOO0OSALIN21110 OOOOO0SALIN31110 000000SALIN40000 000000SALIN50000 BOFAN For example OOOO00SALIN11110 That means when input 1 SOS key is pressed PT600X will send SOS alarm on platform send alarm SMS to SOS number call to SOS number but do not take photo www bofan cc OOO000SALIN41111 1U41111 a bcd e fH h a Send ig
7. A SMS Example OOOOOORCA SMS reply Center Nigang West Road Side Rd Futian Shenzhen Guangdong China Notes tracker can only reply the detail address in English PT600X will only reply command from a user which uses the correct password Command with wrong password will be ignored Take photo by extra camera Please connect camera to PT600X well before using this function You can login LiveGTS software to click Take photo button after PT600X connects to server successfully Please refer to picture below WA TE RSE el mG ltl P eee a Take Photo Restart GPS T eo Fence Speed Alarm Update Position Report Interval Stop Engine Clear Stored Data Send 5M5 m att A NET THR ER mt E TE aa Py Ts m E EG el EO ise Phi Il sh axe s fter clicki he Tak Ph oto will show up on the map after clic nate ake Photo Googe mn a button and the photo can also be saved by clicking it i 9 BOFAN 5 SMS Command List Remarks the device password is 000000 as default Description Get tracker firmware version Get current location Two way communication please install speaker and microphone on PT600X before using this function Extending use of two way communication Voice Monitoring please install microphone on PT600X before you use this function Extending use of Voice Monitoring Get street address by SMS request
8. GPRS cost it is to use Time Interval and ACC Ratio then you can send below command to tracker to configure Notes you must connect car s ignition with PT600 s input4 ACC wire when using this command SMS Example 000000GT130 0 0 0 240 Then PT600X will report data to server every 30 seconds when car is moving but report data every 2 hours 30secondsx240 7200seconds 2hours when car s ignition is OFF The complete command s explanation Example OO0O000GT1I30 300 30 120 240 Then PT600X will send report data to server every 30 seconds when car is moving PT600X will report data to server every 300 meters distance PT600X will report data to server when car turns bend for 30 degree or over 30 degree PT600X will send report data to server every 1 hour 30 seconds x 120 3600seconds 1 hour when car stops moving And PT600X report data to server every 2 hours 830secondsx240 7200seconds 2hours when car ignition is OFF Now back to LiveGTS and go to Real time page select your tracker ID you will see your tracker on the map All above settings are basic steps to connect to the software 9 BOFAN After PT600X connects to server successfully you can also www bofan cc Get street address by SMS request The tracker must work on the LiveGTS successfully and got good GPS amp GPRS signal Then you can send the SMS command to get the detail address instead of latitude and longitude Command lt password gt RC
9. GPS Vehicle Tracker with Camera PT600X User Manual Please read carefully before operation www bofan cc BOFAN 1 Product overview www bofan cc PT600X is an improved version based on PT600 it is a GPS GSM GPRS tracking device which is specially developed and designed for vehicle real time tracking and security With superior GPS and GPRS modules PT600X has good sensitivity and stable performance Especially PT600X is well designed to work with LiveGTS our web based tracking system which is suitable for a company to establish their own tracking platform to provide real time tracking service to their customers or manage their fleet Main features Tracking via SMS or GPRS Current location report Tracking by time interval SOS alarm available to preset 3 SOS number Geo fencing control Low battery alert Speed alert Engine Cut optional Position logging capacity up to 30000 waypoints if no GPRS signal Save half GPRS cost at least when working on FMS in different ways BOFAN Smart Report Tech ACC Mileage Motion sensor Get street address by SMS request Get Google link for current location by SMS request Compatible with car alarm existing in car originally Support door open close status available to control open close car by SMS or platform Support taking photo by extra camera optional 6KB for each photo Take photo at a preset time interval Take photo automatically and send to server by interval whe
10. MSS3 The larger value the lower sensitivity ACH Alarm Char Alarm IN1 for input1 SOS Alarm IN2 for input2 IN3 for input3 IN4 for input4 IN5 for input5 SPD for over speed alarm GEO for geo fence alarm MLA for Mileage Alarm SKA for shake alarm it means PT600X will send a Engine Start SMS to SOS number when there is ignition on alarm Clear Saved data lt password gt CSV Check previous command setting lt password gt ASK lt Command gt Basic GPRS setting for connecting device to server Ensure that your SIM card supports GPRS service Set ID lt password gt GID lt ID gt CSV Clear Saved data Examples 000000ASKSVR to check the server amp port what you set OOOOOOASKGID to check the tracker ID what you set Tracker ID can t exceed 10 digit e 19 BOFAN Set APN Set Server Set Time Interval for Sending GPRS Packet to software server 6 Trouble shooting Problem Device can t power on Possible Cause Wiring was not connected properly Battery needs charging Problem Device doesn t respond to SMS Possible Cause GSM antenna was not installed properly Low power GSM Network is slow Wrong password in your SMS or wrong SMS lt password gt APN lt APN gt lt Username gt lt Pa ssword gt lt password gt SVR lt domain gt lt Port gt lt password gt GTI lt Time Interval gt lt Distant Interval gt lt Angle gt lt Move Ratio gt lt ACC Ratio gt
11. alid even don t configure PT600X s GPRS connecting PWD Password must be 6 digits RPW Reset Password Please long press the SOS button when you send this command to PT600X new password must be 6 digits SOS Number Preset phone number to receive phone call or SMS from PT600X Max 16 digits Maximum 3 SOS numbers can be set 14 BOFAN Set Over Speed Alert lt password gt SPD lt Max Speed gt When car speed is higher than the preset value PT600 will send an alert SMS to the preset SOS number Set Geo fence Alert lt password gt GOF lt Type gt lt SWLat gt lt SWLn g gt lt NELat gt lt NELng gt When car leaves out or enters a preset scope PT600 will send one Geo fence SMS to the preset SOS number Set Mileage Alert lt password gt MLA lt base mileage gt lt increment gt This Mileage Alert can be sent to your mobile by SMS if you set your mobile number as SOS number into this tracker installed in car and it also can be sent to your email address if you set your email address in software successfully Set Odometer lt password gt SOD For example 000000SOD or 000000SODO0 it is to set the tracker s odometer to be 0 000000SOD100 it is to set the tracker s odometer to be 10km 100 100meter 10000m 10km Command 000000SOD5000 it is to set the tracker s odometer to be 500km 5000 100 500000m 500km Set time zone for tracker lt password gt TMZ lt Time gt After setting tim
12. ats a Ll il np Trj a fi F ie i ia J i i Format 22 32 40 81 22 542068 22 32 40 81 22 54268 Wote If lat or Ing is S or vy please add before data Address 4 2 How to live track on LiveGTS platform If you want to do live tracking on platform you need strictly set tracker ID server Port APN and time interval for PT600X as per below steps 4 2 1 4 2 5 Firstly please ensure that your SIM card in PT600X supports GPRS connection prior to setting 4 2 1 Add the tracker into LiveGTS software Login LiveGTS You can open your tracking website by IE and login with your account Go to Manage gt Tracker Config gt click Add New Tracker please fill in name and tracker ID select correct tracker Model click Modify button to add this tracker into software successfully Modify GPS Tracker Name PTROOMtest 1152011 pase Please input digital number Tracker ID Tracker ID must start with 115 This is a public account please don t use SIM card number as tracker ID Model PTaOO is Notes Name you can use any name for your tracker Tracker ID Tracker ID can be any digit numbers you want but must start with the fixed three numbers shown in FMS or your private E 10 BOFAN account here in this example tracker ID starts with fixed 115 on demo website and total numbers includes 115 should be www bofan cc less than 10 digital Mode
13. e zone into tracker you can get your local time in tracker reply message www bofan cc If only set the 1st number PT600X will send SMS and then call to this first number after pressing SOS button If set the 2nd or 3rd numbers too PT600X will send SMS to all 3 numbers only call to the 1 number after press SOS button Note lt password gt SOS command is for cancel all pre set numbers SPD Speed Max Speed the preset speed value 0 to turn off this function 0 500 unit Km h Example 000000SPD80 it will send alert when it is over 80Km h GOF Geo Fence Type 1 alert when out of range Type 2 alert when enter this range SW South West NE North East Example OOOOOOGOFO to turn off this function MLA Mileage Unit 100 meters Example OOOOOOMLA100000 50000 This example means if the tracker records the car driving more than 10000km tracker will send one Mileage Alert for each 5000km mileage increments SOD Set Odometer unit 100 meters TMZ Time Zone Time from 13 to 13 Example 000000TMZ8 BOFAN Restart Reset PT600X to default Request Power Cut Power Alarm Get IMEI Output Control usually for stop car remotely via extra relay Take photo at a preset time interval Note this feature is valid wnen PT600X s firmware version is 1 40 above Set Alarm Action lt password gt RST lt Type gt lt password gt DFT lt password gt RPO lt password gt CPA lt Val
14. help you program it For Analog Input If you want to use this analog input sensor please get the sensor minimum and maximum voltage and program it by AV command firstly then define AD on software or program AD Alarm by SMS command according to your needs BOFAN www bofan cc Third turn on the tracker ha GSM ON OFF make this toggle switch on left sicle to turn on PT600X After turn on the tracker please refer to the signal light Functionality GPS signal Light indicating GPS signal status RED light Flashing fast RED light Flashing on for 2 seconds and off for 2 seconds Green light Flashing on for 0 1 second and off for 2 9 seconds GSM signal Light indicating GSM signal status RED light Flashing fast RED light Flashing on for 2 seconds and off for 2 seconds RED light Flashing on for 0 1 second and off for 2 9 seconds Green light Flashing on for 2 seconds and off for 2 seconds Green light Flashing on for 0 1 second and off for 2 seconds Power Light indicating Power status Green Light keep on bright Green Light keep on flashing Red Light keep on flashing RED Light Flashing fast GPS Power Light GSM ON OFF SM Q K The unit is being Initialized Initialization succeed but GPS signal does not fix PT600X has GPS signal The unit is being Initialized Initialization succeed but GPS signal does not fix PT600X is connected to the GSM network
15. is 21 4kbps 8 8 x 8 3 x 3 5 cm 3 Getting started This section will describe how to set up your PT600X 3 1 Hardware and Accessories BOFAN PT600X standard package includes following items e 1 PT600X Main Unit e 1 GPS Antenna e 1 GSM Antenna e 1 Plug in power Wires www bofan cc Optional accessories e Speaker the new speaker interface is different with the old one e Microphone the new microphone interface is different with the old one e Normal Camera the new normal camera interface is different with the old one e Relay Optional for cutting off oil engine to stop car 12V relay for car 24V relay for truck JIE BUSA g ae e GPS Antenna e GSM Antenna e Plug in power Wires e Speaker e Microphone Camera e Relay Optional Optional Optional Optional 3 2 Connecting and Installation If you install your tracker in car directly please follow below steps Notes If you test your tracker in office please charge the tracker via 12V external power charger for 3 hours at least before following below steps once you connect the tracker power wire red black to external power supply wire directly it is in charging First install the SIM card into tracker Press the yellow button to make the Card Holder out Notes the SIM card must support GPRS service and when you install this SIM card in mobile you can use this mobile dial phone answer coming calling send and receive SMS It
16. is GSM card not CDMA card And please disable the SIM card PIN code BOFAN www bofan cc connect the GSM Antenna connect the GPS Antenna connect the wires Red wire connect to positive pole of car battery DC In Input voltage 9V 35V 12V suggested Black wire GND one connect to cathode of car battery The other one already connects to SOS key White wires Digital Inputs Refer to Examples of Interfacing Applications below the wires is optional please do not connect them if not necessary Yellow wires Output Inputs Refer to Examples of Interfacing Applications below the wires is optional please do not connect them if not necessary Blue wires 10 Bits Resolution Analog Inputs Input voltage 0 6V Refer to Examples of Interfacing Applications below the wires is optional please do not connect them if not necessary BOFAN Examples of Interfacing Application I O www bofan cc ADS output AD outpute Anode outputs GND 2 Microphone Speaker Camera USBE is Inputo Power All gt MIC SPK Camera ag 7 2 ies input ta GND1 Red input Black AD input2 Le ADA inputi Yellow White Fress Notes When you need to disconnect PT600X s plug in wire speaker microphone camera please press the socket 2 at first and then disconnect it For Input Ports 1 SOS Button Input 1 Input 2 Input 3 SE C White i ee Input 1 or Input 2 or Input 3 2
17. l must choose the correct model number PT600 Please remember click Modify button after you input information At now please use your mobile to send below SMS commands and configure it to work with LiveGTS Software after you do all below setting you can be back to LiveGTS software real time to check your tracker online Notes use your mobile to send following SMS commands to PT600X SIM card number to program it work on LiveGTS software please ensure to get tracker s response for your command and then go on sending next command PT600X will only reply command from a user which uses the correct password Commands with wrong Password will be ignored 4 2 2 Set ID for PT600X Command format lt password gt GID lt ID gt Example 000000GID1152011 PT600X will reply with an SMS SET OK ID 1152011 to confirm this setting Notes Please use the exactly full tracker ID includes 115 you preset into tracking software LiveGTS in above step 4 2 1 4 2 3 Set APN Command lt password gt APN lt APN gt lt User gt lt Pass gt Example OOOOOOAPNCMNET PT600X will reply with an SMS SET OK APN CMNET USER PASS to confirm this setting CMNET is China mobile s APN no username amp password in this example Notes You can ask your GSM operator for your APN username and password it is used to report data from SIM card to server if your APN has no username and password please input APN only 4 2 4 Set server and po
18. mand lt password gt RCP For example you edit this SMS QOOOOOORCP on your mobile phone and send it out to the SIM card number in PT600X Notes The default password of tracker is 000000 if you already changed the tracker password please use the new password in command After a few seconds you will get a SMS reply with below content on your mobile phone Latitude 22 5632 Longitude 114 0940 Speed 2 6854Km h Odometer 10 98KM GPRS ON EXPW OFF Time 2010 12 07 08 47 45 Explanation GPRS means GPRS state ON GPRS connect ok OFF GPRS disconnect Fail GPRS connect fail EXPW means external power state ON connect external power already OFF disconnect external power Notes when your tracker doesn t get GPS signal it will reply a SMS with Last Lat 22 5632 Lng 114 0940 Speed 0 00KM h Odometer 0 000KM GPRS OFF EXPW OFF_ Time 2010 12 08 08 58 45 It means this data is for the last place where the tracker got GPS signal successfully You can visit our LiveGTS demo http demo livegts com which includes the Google map manually input the latitude and longitude what you get from this reply SMS and click the Locate button It will display the location on map Please refer to following picture BOFAN www bofan cc z LiveG a S Live GPS Tracking System Find building addresses and road GPS Tracking Get Directions Please Enter Lat 40 75659 Lng 73 98618 fa j a 7 k F E j 4 f Pole D
19. n SOS or Geo fence or other alarm types trigger Available to set different alarm notification ways when alarm sending alarm SMS call platform or taking photo Car maintenance remind by mileage report Support alarm in case of oil leakage when working with LiveGTS on FMS Automatically cut off oil or activate siren locale when Geo fence or speed alarm triggers Support shake alarm Support voice monitoring and two way conversation Mileage and GPRS report by distance Support RFID function by extra card reader Optional I O 5 digital inputs 3 negative and 2 positive triggering 4 outputs Analog Input 4 10 bits resolution analog inputs For operate safely please refer to following simple guidelines Proper Connection When installing tracker in vehicle please read the manual carefully Correct installation Don t connect it to other incompatible devices Qualified Accessories Use original parts qualified batteries and peripheral equipments to avoid damage to PT600X Safe Driving Drivers should not operate this device while driving Qualified Service Only qualified person can install or repair PT600X Water Resistance PT600X is not water resistance Keep it dry Install it inside the vehicle Confidential Phone Number For safety reason don t tell your PT600X s SIM number to others without taking precautions of security settings BOFAN GPS communication is liable to be affected by environmental shielding may fail to car
20. nition on alarm to software real time page and email address b Send ignition on alarm to SOS number by SMS c Call SOS number when there is ignition on alarm d Take photo automatically when there is ignition on alarm e Send ignition off alarm to software real time page and email address f Send ignition off alarm to SOS number by sMS g Call S03 number when there is ignition off alarm h Take photo automatically when there is ignition off alarm 1 means activate this function 0 means close this function AD alarm lt password gt AD lt index1 gt lt index2 gt Index1 1 means AD 1 lt Parameter gt lt alarm name gt lt index3 gt 2 means AD 2 3 means AD 3 4 means AD 4 Index 2 lt gt Parameter 0 100 unit Alarm name default is AD1 alarm if you use fuel alarm at here you will get alarm fuel alarm SMS contents Index3 1 means input1 2 means input2 3 means input3 4 means input4 5 means input5 For example 000000AD1 lt 10 Fuel Low 4 After you connect fuel sensor to PT600X AD1 wire PT600X will send Fuel Low alarm SMS to SOS number when tracker get AD1 data lt 10 but this alarm is effective only when input4 on if you connect input4 to car ignition then it means car ignition on Notes if your fuel sensor keep working even when car ignition off you don t need to set index3 as input4 here 000000AD2 gt 30 Temp High 4 After you connect temperature sensor to PT600X
21. oor Battery power is low Problem Can t real time tracking on platform Possible Cause GPRS setting is not correct APN is wrong Tracker ID set by SMS command is not same as that one written in software Recharge credit of the SIM card Insert working SIM card Check in phone that the SIM can send SMS message Check in phone if the SIM card can send SMS message Replace SIM card if need Remove PIN code by inserting SIM card in your phone and deleting the code Inspect SIM card clean the contacts If re installing does not help try another to check If you are in another country your SIM card must have roaming service enabled Resolution Move the antenna of the unit to a location where the sky is visible Make it work in an open area outside Recharge device Resolution Please set each step strictly according to user manual Ask your GSM provider for the correct APN username and password if it has then set again Check if the trackers ID you set into tracker is same exactly as the one you write in software www bofan cc Welcome to contact your sales representative in our company or by email bofanelectronics qmail com if you have any questions 21
22. rt Command lt password gt SVR lt domain gt lt Port gt Example O0O0OOOOSVRDEMO LIVEGTS COM 8600 PT600X will reply with an SMS SET OK IP DEMO LIVEGTS COM to confirm this setting Notes The domain name in this command must be in capital and DEMO LIVEGTS COM just is an example at here please using your domain name when you program your tracker to work on your tracking platform PT600X s port always is 8600 BOFAN 4 2 5 Set Report Time Interval for Sending GPRS Packet Command lt password gt GTI lt time seconds gt SMS Example 000000GTI30 www bofan cc Then PT600X will report data by GPRS to server every 30 seconds We suggest time interval gt 30 seconds Time interval value should not exceed 65535 seconds Notes We suggest set report time interval simply as above when testing initially Special and Extended Commands for setting report time interval If no special demand it isn t necessary to use Command lt password gt GTl lt Time Interval gt lt Distant Interval gt lt Angle gt lt Move Ratio gt lt ACC Ratio gt If you want to save GPRS cost the normal way is to use Time Interval and Move Ratio only you need send below command to tracker to configure SMS Example 000000GT130 0 0 120 Then PT600X will report data to server every 30 seconds when car is moving but report data every 1 hour 30secondsx120 3600seconds 1hour when car is not moving There is another way of saving
23. ry out positioning during certain circumstances It www bofan cc will resume the positioning function as soon as it leaves the shielding environment This is normal Please do not worry when encountering such problem Each signal sent out from the system will be confirmed for successful transmission in the base station of the mobile operator However if system stoppage occurs or if the mobile telephone is preset to a switch off state by the customer it cannot ensure successful transmission 2 Parameters of PT600X Feature Power Supply Power Consumption For VBATT Operating Temperature Range Storage Temperature Range Humidity External Antenna External SIM Card SIM card type Transmit Power Sensitivity Speech Codec GPRS Dimensions Characteristics 9V to 40V Active mode peak lt 1 0A Active mode avg lt 300mA Idle mode lt 15mA 20 C to 60 C 20 C to 70 C Up to 75 non condensing Connected via the 500 coax connector Connected via SIM Card connector 3V Class 4 2W for E GSM 900 and 850 Class 1 1W for DCS 1800 Class 1 1W for PCS 1900 104 dBm minimum for E GSM 900 and 850 102 dBm minimum for DCS 1800 102 dBm minimum for PCS 1900 Triple rate Codec Half rate ETS 06 20 Full rate ETS 06 10 Enhance Full rate ETS 06 50 06 06 06 08 Multi slot Class 8 4Rx 1Tx 5 slot Max Support all 4 coding schemes CS 1 CS 2 CS 3 and CS 4 e Maximum download speed is 85 6kbps e Maximum upload speed
24. ue gt lt password gt IME lt password gt OPC lt Index gt lt Action gt lt password gt PTl lt time interval gt lt password gt AN lt Index1 gt lt Index2 gt lt Inde x3 gt lt Index4 gt www bofan cc RST Restart Type 0 or null to reboot PT600X Type 1 to reboot GPS Type 2 to reboot GSM DF T Default RPO Request Power Voltage CPA Cut Power Alarm Value 0 to disable Cut Power Alarm Value 1 to enable Cut Power Alarm Default set 000000CPA1 To get tracker s IME number Note IMEI number can t be tracker ID number OPC Output Control Index 1 means Out1 2 means Out2 3 means Out3 4 means Out4 Action 0 to close the output 1 to open the output PTI Photo Time Interval Time Interval 0 to turn off this function Time Interval 120 65535 unit second Example OOOOOOPTI300 PT600X will take photos every 300 seconds AN Action Index1 1 mean NO 1 Action it can be 1 5 Index2 OPC2 1 means trigger output2 on OPC3 1 means trigger output 3 on TEL13112345678 means trigger this TEL command to call 13112345678 any other command can be done at here Index3 Time Unit second If you want to automatically close the above alarm or trigger another alarm in few seconds please input the time at index3 and also input next close alarm command at index4 a 16 BOFAN Set Alarm Different alarms can be set at the same time 6 99 just use between different
Download Pdf Manuals
Related Search