BY65.5SS 60cm 4 Solid plate electric hob
Contents
1. A SEALING STRIP have cut out On the underneath of the hob place the clamp s B into position on in each corner of the hob Adjust the clamps into a position that is Suitable for your worktop as shown in the diagrams on the left Slightly tighten the screw C through each clamp B so that the clamp is attached to the hob Once you are satisfied of the position of the hob you can fully tighten the screws C to secure the hob into position 16 Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the E E Regulations and in compliance with Manufacturer s instructions Before connecting the appliance make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage WARNING THIS APPLIANCE MUST BE EARTHED o This appliance must be wired into a 30 A double pole switched fused spur outlet having 3 mm contact separation and placed in an easily accessible position adjacent to the appliance It should not be located above the appliance and no more than 1 25m away from it o The spur outlet must still be accessible even when your hob is located in its operating position o Cable type HO5 RRF 3 core x 2 5 mm Connecting the mains supply cable o The mains terminal block is located on the underside of the hob and the terminals are accessible by removing the terminal block cover by removing the cover scre2. o 55 mm clearance between the back of the hob surface and the wall behind it o Ifthe hob is positioned so that the right or left hand side of the appliance will be near to the edge of a kitchen unit There must be a gap of at least 150 mm between the side of the hob and the vertical surface of the kitchen unit Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging 1 hob 1 Installation and instruction manual 1 guarantee card 4 Fixing screws 4 Clamps 1 Sealing strip 14 Installing the appliance o Cuta hole in the worktop that corresponds with the drawing shown above o IMPORTANT You must have a gap of at least 15 mm between the underneath of the appliance and any surface that is below it o Carefully turn the hob upside down and place it on a cushioned mat 15 o Remove the protective covering from the sealing strip o Apply the sealing strip provided around the edge of the appliance o Do not leave a gap in the sealing strip or overlap the thickness IMPORTANT Do not use a silicon sealant to seal the appliance against the aperture This will make it difficult to remove the hob from the aperture in future particularly if it needs to be serviced o Carefully turn the hob back over and then gently lower it into the aperture hole that you A SEALING STRIP C SCREW B CLAMP A SEALING STRIP C SCREW B CLAMP
3. olive oil onto a kitchen towel and rub it onto the surface of the plate The next time the plate is used it may produce a little smoke Alternatively you can use a hotplate conditioner these products can normally be found at larger supermarkets and hardware Stores The manufacturer s instructions should be followed when using these products IMPORTANT If the solid plates are not maintained regularly with olive oil or a hotplate conditioner then they may rust nstallation The installation must be carried out by a suitably qualified person in accordance with the current version of the following UK Regulations and Safety Standards or their European Norm Replacements Building Regulations issued by the Department of the Environment Building Standards issued by the Scottish Development Department IEE Wiring Regulations Electricity At Work Regulations 13 Positioning The adjacent furniture must be able to withstand a AN minimum temperature rise of 85 C above the ambient temperature of the room it is located in during periods of use This appliance is classified as Class 3 and therefore is to be built into a kitchen unit depending on size or 600 mm worktop that is at least 30 mm thick The following minimum clearance distances must be observed o 700 mm between the hob surface and the underside of any horizontal surface above it o 50 mm clearance around the sides and front of the appliance
4. ER CARE DEPARTMENT IMMEDIATELY 11 Cleaning and maintenance Cleaning and maintenance operations must only be carried out when the hob is cool The appliance should be disconnected from your mains supply before commencing any cleaning process Cleaning the hob top A A Any residues that are left on the hob top surface from cleaning agents will damage it You should remove any residues with water and a little washing up liquid Abrasive cleaners or sharp objects will damage the hob surface you should clean it using water and a little washing up liquid Although it is easier to clean some deposits whilst the hob surface is still warm you should take care not to burn yourself if cleaning the hob surface when it is still warm After each use O Wipe the appliance over with a damp cloth and a little washing up liquid Dry the appliance by rubbing the surface with a clean cloth If the hob top is heavily soiled then if the hob surface is made from stainless steel then a suitable stainless steel cleaner should be used IMPORTANT If a stainless steel cleaner is not used regularly then it is possible for the surface of the hob to change colour over a period of time 12 Maintaining the solid plates O O O If something is spilt onto the plate itself then it can be removed using a soft brush plastic or nylon scourer and warm water To keep the solid plates in good condition you should put a little
5. User Manual for your BY65 5SS 60cm 4 Solid plate electric hob NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a Safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance GS 09 11 12 Contents Environmental note IMPORTANT SAFETY INFORMATI ON Specifications Product and aperture dimensions Product specifications Standard accessories Electrical details Hob surface layout Using the hob Before first use Control knobs Switching on a zone and setting a power level Hob guidelines Cleaning and maintenance Cleaning the hob top After each use Maintaining the solid plates Installation Positioning Unpacking the appliance Installing the appliance Electrical connection Connecting the mains supply cable Replacing the mains supply cable My appliance isn t working correctly Contact details 12 13 12 12 13 13 18 14 14 15 16 17 17 18 18 19 20 21 Environmental note This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by ina
6. ans must be positioned exactly on these zones for efficient heating to occur Pans should have the same diametre as the cooking zone that they are being used on You should not use saucepans with rough bottoms as this can scratch the solid plates Before use make sure that the bottoms of the saucepans are clean and dry When cold the bottom of the pans should be slightly concave as they expand when hot and lie flat on the surface of the hob This will allow the heat to transfer more easily The best thickness for the bottom of the pans is 2 3 mm of enamelled steel and 4 6 mm for stainless steel with sandwich type bottoms If these rules are not followed then there will be a great loss of heat and energy Heat not absorbed by the saucepan will spread to the hob frame and surrounding cabinets Preferably cover pans with a lid to permit cooking at a lower heat Always cook vegetables and potatoes etc in as little water to reduce cooking times Food or liquid that has high sugar content may damage the hob top if it comes into contact with the hob surface Any spillages should be wiped up immediately however this may not prevent the hob Surface from becoming damaged IMPORTANT The hob surface is tough however it IS not unbreakable and can be damaged Especially if pointed or hard objects are allowed to fall on it with some force DO NOT USE THE HOB IF THE SURFACE BECOMES BROKEN OR CRACKED YOU SHOULD CONTACT THE CUSTOM
7. ary repair If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then they will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by the manufacturer has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance IMPORTANT The Manufacturer operates a policy of continuous improvement and reserves the right to adjust and modify its products without prior notification 20 United Kingdom 6 Bennet Road Reading Berkshire RG2 OQX United Kingdom Customer Care 0118 933 6918 2l
8. be switched on without cookware placed on it Also the cookware should not be empty Product dimensions Aperture dimensions Depth 500 mm Depth 480 mm Width 580 mm Width 560 mm Height 45 mm Product specifications 1 x 2 00 kW rapid plate 180 mm 1 x 1 50 kW rapid plate 145 mm 1 x 1 50 kW standard plate 180 mm 1 x 1 00 kW standard plate 145 mm O O O Electrical details Rated Voltage 230 240 Vac 50 Hz Supply Connection 30A double pole switched fused outlet with 3mm contact gap Max Rated I nputs 6 00 kW Mains Supply Lead 3 core x 2 5 mm not supplied For future reference please record the following Information which can be found on the rating plate and the date of purchase which can be found on your sales invoice The rating plate of your hob is located on the underneath of the appliance Therefore it is a good idea to record this information before you install your appliance Model Number Serial Number Date of Purchase Hob surface layout A 1 50 kW standard plate 180 mm B 2 00 kW rapid plate 180 mm C 1 00 kW standard plate 145 mm D 1 50 kW rapid plate 145 mm Using the hob Before first use IMPORTANT You should clean the hob surface and solid plates see Cleaning and maintenance section o You should switch on one cooking zone at a time for 5 minutes at the maximum setting This will help to eliminate any new smell that exists and evap
9. his appliance and when following the cleaning procedure You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance Installation O This appliance must be correctly installed by a suitably qualified person strictly in accordance with the manufacturer s instructions Please see the specific section of this booklet that refers to installation The manufacturer declines any responsibility for injury or damage to person or property as a result of improper use or installation of this appliance Declaration of conformity This appliance complies with the following European Directives 2006 95 CE General regulations Low tension 1935 2004 CE 90 128 EEC This appliance is suitable to come in contact with food 2004 108 CE Electromagnetic compatibility O The manufacturer declares that the hob is built using certified materials and requires the appliance to be installed in accordance with the standards currently in force This appliance must be used by a trained person for domestic purposes only To avoid damaging your appliance O The hob surface can be damaged by objects falling onto it The edge of the hob surface can be damaged by knocks from cookware Cast iron and cast aluminium cookware with damaged bases may scratch the hob surface if they are dragged across it 7 o Pans should be lifted on and off the hob surface and not dragged o Cooking zones should not
10. of vinyl or laminate kitchen furniture are particularly prone to heat damage or discolouration at temperatures below the guidelines given above o Any damage caused by the appliance being installed in contravention of this temperature limit will be the liability of the owner o Your new appliance is guaranteed against electrical or mechanical defects subject to certain exclusions that are noted in the manufacturer s Conditions Of Guarantee The foregoing does not affect your statutory rights o The use of this appliance for any other purpose or in any other environment without the express agreement of the manufacturer will invalidate any warranty or liability claim o You should not use this appliance to store items on or as a work Surface o No modifications to the appliance are permitted by the manufacturer o You should not store or place flammable or highly flammable liquids materials on top of or near the appliance Items made from aluminium plastic or plastic film should also be kept away from the appliance as they may fuse to the surface o Repairs may only be carried out by authorised service engineers or their authorised service agents Child Safety o The manufacturer strongly recommends that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time During and after use all surfaces will become hot If it is necessary for younger family members
11. orate any humidity that has formed on the heating elements during transit o When doing this burn off process an appropriately sized Saucepan containing cold water should be placed on the zone in question o Do not burn off more than one zone at once Control knobs o All operations are performed by means of the 4 control knobs that can be found on the right hand side of the hob top o The control knobs can be turned either clockwise or anti clockwise to select a heating level The numbers around the outside of each control knob indicates the power level that you have set the zone to o A marking to the bottom right of each control knob indicates which zone that it controls Switching on a zone and setting a power level o Turn the control knob of the zone that you wish to cook on clockwise or anticlockwise until it reaches the power level that you desire o Each cooking zone can be adjusted between 1 and 6 one being the coolest zone setting and six being the hottest zone setting o When you have finished cooking make sure that you turn the control knob anti clockwise to the 0 position 10 Hob guidelines O The first few times the hob top IS used It may give off an acrid burning smell This smell will disappear completely with repeated use The hob surface is fitted with cooking areas of different diametre and power The positions where the heat will radiate from are clearly marked on the hob top The saucep
12. ppropriate waste handling of this product The symbol it on the product or on the documents accompanving the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact vour local city office your household waste disposal service or the shop where you purchased the product o The packaging materials that manufacturer uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to us Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in this booklet please contact Customer Care General I nformation o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs o IMPORTANT The adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature of 85 C above the ambient temperature of the room it is located in whilst in use o Certain types
13. the live and neutral wires o The blue neutral wire must be connected to the terminal marked with letter N the live wire must be connected to the terminal marked with letter L 18 My appliance isn t working correctly o The cooking zones are not functioning or will not switch on Check that the mains electrical supply to the appliance is correct and working Check the mains fuse o A humming sound is heard when a cooking zone is selected This is normal the sound will disappear when the zone heats up o The cooking zones have become discoloured This maybe caused by burnt on remnants of food This will not affect the working of the appliance However you should make Sure that the cleaning instructions are being followed regularly o Only two of the zones on my hob are working You should recheck that the terminal screws are all fully tightened between the links 19 IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number 0118 933 6918 DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necess
14. to be in the kitchen please ensure that they are kept under close supervision at all times Older children should only be allowed to utilise the appliance when supervised General Safety v The appliance should only be installed and connected by a Suitably qualified person Care should be taken to ensure that the units and work surfaces that you build the appliance into meet with the relevant standards If you notice any scratches splits or cracks in the hob surface you should immediately switch off the appliance and disconnect it from your mains supply Otherwise there is the risk of electric Shock occurring During use v Any film or stickers that are present on the hob surface when it O IS delivered should be removed before use Care should be used when utilising the appliance otherwise there is a risk of burns being caused You should not allow the electrical connection cables to come into contact with the hob surface when it is hot or any hot cookware If fat and oil overheats then it can ignite extremely quickly For this reason when cooking with fat and oil the appliance should not be left unattended Make sure that all of the cooking zones are switched off after use Cleaning O Cleaning of the hob should be carried out on a regular basis IMPORTANT Before attempting to clean the appliance It should be disconnected from the mains and allowed to cool Great care should be taken whilst using t
15. w Tustist Eee 400V 2N o The cable connections must be in accordance with the diagram located on the bottom of the hob 17 o The brass links must be positioned as marked in the diagram opposite and once established ALL terminal screws must be tightened down firmly o If when the hob is first switched on only two of the zones work you Should recheck that the terminal screws are all fully tightened between the links This should be done before contacting the Customer Care Department o IMPORTANT The appliance must NOT be connected to the mains supply by means of a 13A plug and socket o The cable can be looped if necessary but make sure that is not kinked or trapped when the hob is in position Care must be taken to avoid the cable being in contact with hot parts of the appliance Replacing the mains supply cable If the mains supply cable is damaged then it must be replaced by an appropriate replacement which can be obtained from the Spares Department The mains supply cable should be replaced in accordance with the following instructions o Switch the appliance off at the control switch o Open the terminal block on the underside of the hob o Unscrew the terminal screws fixing the cable o Replace the cable with one of the same length and in accordance with the specification given above o The green yellow earth wire must be connected to the terminal marked It must be about 10 mm longer than
Download Pdf Manuals
Related Search