Home

TEM# 1411202 Air Hammer Combo USER`S MANUAL

1. JELA bk Air Tools TEM 1411202 Air Hammer Combo USER S MANUAL Read carefully and understandRULES FOR SAFE OPERATION and instructions before operating Failureto follow thesafety rules andother basic safety precautions may resultin serious personal injury Made in China For technical questions and replacement parts please call 1 800 222 5381 Thank you very much for choosing a NORTHERN TOOL EQUIPMENT CO Product For future reference please complete the owner s record below Model _ Purchase Date Save the receipt warranty and these instructions It is important that you read the entire instruction sheet to become familiar with this product before you begin using it This product is designed for certain applications only Northern Tool Equipment strongly recommends that this product is not modified and or used for any application other than that for which it was designed If you have any questions relative to aparticular application DONOT use the product until you have first contacted Northern Tool Equipment to determine if it can or should be performed on the product Before using this product please read the following instructions carefully Technical Specifications Item Description Item Description Blows per minute 2000 Air Consumption 6 CFM Shank Opening 3 4 Air Inlet Diameter 1 4 18NPT Air Hose Size 3 8 Accessories 5 chisels 1 needle scaler SAV
2. 4 Guard against electric shock Prevent bodycontact with grounded surfaces such as pipes radiators ranges and refrigerator enclosures 15 Do not operate tool if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment orreflexes are impaired while taking drugs If there is any doubt do not operate the tool 16 Use proper size and type extension cord Ifan extension cord is required for the air compressor it must be of the proper size and type to supply the correct current to the tool without heating up Otherwise the extension cord could melt and catch fire or cause electrical damage to the tool Check your compressor s manual for the appropriate size cord 17 Foryour safety maintenance should be performed regularly by a qualified technician 18 Use compressed air only Never use combustible gases as a power source Note Performance ofthe compressor if powered by line voltage may vary depending on variations in local line voltage Extension cord usage may also affect tool performance ZN WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm some examples of these chemicals are A Lead from lead based paints B Crystalline silica from bricks and cement or other masonry products C Arsenic and chromium from chemicall
3. E THIS MANUAL You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts listand assembly diagram Keep this manual and invoice in a safe and dry place for future reference WARNINGS AND SAFETY RULES 1 Keep work area clean Cluttered areas invite injuries 2 Observe work area conditions Do not use machines or power tools in damp or wet locations Don t expose to rain Keep work area well lighted Do not use electrically powered tools inthe presence of flammable gases or liquids 3 Keep bystanders pets and children away Children must never be allowed in the work area Do not letthem handle machines tools extension cords or airhoses 4 Store idle equipment When not in use tools must be stored in a dry location to inhibit rust Always lock up tools and keep out of reach of children 5 Use the right tool for the job Do notattempt to force a small tool or attachment to do the work of alarger industrial tool There arecertain applications for which this tool was designed It will do the job better and more safely at the rate for which itwas intended Do not modify this tool and donot use this tool fora purpose for which it was not intended 6 Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair coverin
4. Makesure the immediatearea is clearof other people or animals Spectators must stay at asafe distance 7 Never pointthe tool orthe air hose not included atanyone 8 Keep your finger away from thetrigger until youare ready towork Operation Set Up Regulator Recommended Air Line Components Fig 1 1 Youwill need toprepare a 1 4 air connector sold separately to connect to theAir Inlet First wrapthe 1 4 airconnector notincluded with pipethread seal tape before connecting to a AirSource Hose notincluded 2 Attach airhose to theAir Inlet 7 on the AirHammer Note If youare not usingan automatic oiler system before operation add a few drops of Pneumatic Tool Oil to the airline connection Adda fewdrops more aftereach hour ofcontinual use 3 Set theair pressure on your compressor to 90 PSI Do not exceed the recommended air pressure of 90 PSI 4 Check theair connection forleaks 5 Turnoff the compressorand disconnect theair source hosein preparation toload bits into the Air Hammer Use as ahammer A N WARNING Always disconnectfrom the airsource beforeexamining or changingbits 1 Select theappropriate Chisel Bit With yourthumb put counterclockwise pressure on the springand insert the shankof the chiselbit into theCylinder Releasethe spring Holding the AirHammer firmly pull the Nelo hard to make sureit locked into place See Fig 2 aa Fig 2 Note Before connectingthe air supply make sureyou are wearing safetyg
5. ectthe air hose Diagram for theAir Hammer 4of5 Parts List for theAir Hammer Part No Description Qty Part No Description Qty 1 Handle 1 10 Throttle Spring 1 2 Pin 2 11 Hose Adapter 1 3 Ball Seat 1 12 Upper Valve Case 1 4 O ring 1 13 Valve Disc 1 5 Regulator 1 14 Lower Valve Case 1 6 Trigger 1 ills Piston 1 Fi O ring 1 16 Cylinder 1 8 Pin 1 17 Quick Change Retainer 1 9 Pin Seat 1 Diagram for theNeedle Scaler La ony y E B A y i m aA Ge p n gee n e Part No Description Qty Part No Description Qty 1 O ring 2 6 Needle fixer 1 2 Fix Nut 1 7 Needle 19 3 Drive 1 8 Spring 1 4 Body 1 9 Bearing Cover 1 5 Screw 3 5of5
6. g to contain long hair Always wear Steel toe shoes when operating the Air Hammer 7 Use eye and ear protection Always wear ANSI approved impact safety goggles and ear protection Wear a full face shield when breaking up concrete 8 Do not overreach Keep proper footing and balance at alltimes Do not reach over Or across running machines orair hoses 9 Maintain tools with care Keep tools clean for better and safer performance Follow instructions for lubricating and changing accessories Inspect tool cords and air hoses periodically and ifdamaged have them repaired by an authorized technician The handle must be kept clean dry and free from oil and grease atall times 1 of 5 10 Disconnect air supply Disconnect air hose when notin use 11 Avoid unintentional starting Be sure the trigger is not depressed when carrying the Air Hammer 12 Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired 13 Check for damaged parts Before using any tool anypart that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment and binding of moving parts any broken parts or mounting fixtures and any other condition that may affect proper operation Any part thatis damaged should be properly repaired or replaced by a qualified technician Do not usethe Air Hammer ifthe trigger does not turn on and off properly 1
7. oggles and a full facemask ear protection and steeltoe shoes 3 0f 5 A N WARNING Any spectators in the immediatearea will needeye andear protection Beware offlying chips of wood concrete metal or anyother material beingchiseled 2 Connect theair hose tothe Air Inletand turn onthe compressor notincluded 3 Grip theAir Hammer with both hands firmlyand put the chisel tip up against the workpiece you wish to chip 4 Gently squeezethe trigger and move slowlyalong the workpiece Do not pushdown on the tool let it dothe work Ifit does notdo the intended job to satisfaction examine your bit to see ifit is wornor dull 5 When youare finished turnoff the airsupply holdthe Air Hammera safe distance away fromyourself and others and squeeze thetrigger to bleedoff the remaining air Then disconnect theair hose Use as aNeedle Scaler 1 Removethe spring andthe Chisel Bit 2 Take out theneedle scaler fromthe box SeeFig 3 screwit into thecylinder See Fig 4 tighten it SeeFig 5 andstart the trigger Fig 3 Fig 4 Fig 5 3 Gently squeeze the trigger and move slowlyalong the workpiece Do not pushdown on the scaler let it dothe work Ifit does notdo the intendedjob to satisfaction examine yourscaler to seeif it isworn or dull 4 When youare finished turnoff the air supplyand then holdthe Air Needle Scaler a Safe distanceaway fromyourself and others and squeeze thetrigger to bleed off the remaining air Then disconn
8. y treated lumber Yourrisk from exposure varies depending on how often you do this type of work To reduce your exposure to these chemicals work ina well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 etseq WARNING The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that mayoccur Itmust be understood bythe operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Additional Safety Warnings 1 Repetitive motions or exposure to vibration may be harmful to your hands andarms 2 When wearing gloves to operate the Air Hammer make sure that the gloves do not interfere with operating the trigger Test your gloves with the trigger before attaching the unit to an airsource 3 Never start the tool unless you havea firm grip with both hands and you are positioned at your workpiece or area 2 of 5 4 Before usingthe Air Hammer know whatis directly underneath the work areaor workpiece 5 The AirHammer can quicklypenetrate material If working directlyon the ground make sure you are notdirectly above shallow cables lines or pipes 6 Keep your limbs and body clear ofthe Air Hammer If achisel breaks off thetool tends tosurge forward suddenly

TEM# 1411202 Air Hammer Combo USER`S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents