full electronic washing machine user manual
Contents
1. 2 5 Underwears sheet table cloth t shirt shirt towel Slightly dirty cotton coloured and linen textile When you need an additional rinsing to be done to your clothes after the washing process you can use this program for all kinds of clothes SPIN You can use this program when you need an additional spinning to be done to your clo program for your delicate or woolen laundry hes after the washing process Please do not use this DRAIN J Le This program is used to drain the dirty water inside after the washing process of your machine If you want the water inside your machine to be drained before the program ends you can use this program Energy label data based on programme tested in accordance with EN60456 SECTION 6 MAINTENANCE AND CLEANING e Unplug your machine e Close the water tap WATER INLET FILTERS On the tap part of your machine s water inlet hose and at the ends of water inlet valves there are filters to prevent entrance of the dirt and foreign materials in the water to the machine If the machine is unable to receive sufficient water although your water tap is opened these filters should be cleaned Remove the water inlet hose Remove the filters found on the water inlet valves by using a pincer and wash thoroughly with a brush Clean the filters of the water inlet hoses located on the tap side by removing manually together with the seal After y2. It is recommended that the first wash cycle should be made without any laundry So that carry out this water pour half a measuring cup of normal allpurpose detergent into compartment 2 and select cotton program at 90 C BEFORE WASHING Discrimination of your laundry Discriminate your clothes according to their types cotton synthetic sensitive woolen etc washing temperatures and level of dirtiness Never wash your white and coloured clothes together Since your new coloured clothes may shed dye on the first wash wash them separately Be careful that no metal pieces are found on or in the pockets of your clothes remove if there is any Zip and button your clothes Remove the plastic or metal hooks of the curtains and laces or place them inside a washing bag and tie e Pull the textiles like trousers knitted fabric t shirt and sweat shirt inside out e Wash your small clothes like socks and handkerchiefs in a washing bag Xj Wash up tol 90 C Wash up to 60 C Wash upto 30 C Not washable in washing machine Placement of the clothes into the machine e Open the door of your machine e Fill your clothes in your machine in a well spread manner e Place each cloth separately e When you shut the door of your machine be careful that no cloth is jammed between the cover and the gasket Shut the door of your machine tightly otherwise your machine will not start the washing process Filling detergent in the machine The quantity
3. and be rinsed with water mixed with vinegar Shoe Polish The stain should be slightly scratched without ruining the cloth rubbed with detergent and rinsed In case it is not eliminated it should be rubbed with 1 unit of pure alcohol 96 degrees mixed in 2 units of water and then washed with lukewarm water Tea and coffee Stretch the stained area of your cloth on the top of a container and pour water as hot as the type of your cloth can endure on it If the type of your cloth is suitable wash it with lye Chocolate and cocoa By leaving your clothes in cold water and rubbing with soap or detergent wash it in the highest temperature that the type of your cloth can endure If there is still a stain of oil left wipe with oxygenated water in proportion of 3 Tomato paste After scraping the dried pieces without ruining the cloth leave in cold water for about 30 minutes and wash by rubbing with detergent Meat broth egg Eliminate the dried stain residues and wipe with a sponge or soft cloth wetted in cold water Rub with detergent and wash with diluted lye Grease and oil stains First wipe the residues Rub the stain with detergent and then wash with lukewarm soapy water Mustard First apply glycerine to the stained area Rub with detergent and then wash If the stain still does not disappear wipe with alcohol On synthetic and coloured cloth a mixture of 1 unit alcohol 2 units water should be used Blood stain Lay your c
4. by stretching Water drain hose should be mounted at a height of minimum 60 cm maximum 100 cm from the ground The end of the water drain hose may directly be fitted to the dirty water outlet hole or a special apparatus mounted on the outlet bracket of the wash stand Never attempt to extend the water drain hose by adding extra parts MIN 60 CM MAX 100 CM SECTION 3 TECHNICAL SPECIFICATIONS AWG 3102C AWG 5102C AWG 5122C Maximum dry laundry capacity kg 3 5 5 5 Recommended loading kg 3 4 5 4 5 Height cm 85 85 85 Width cm Depth cm 37 42 42 Maximum spin cycle rpm SECTION 4 CONTROL PANEL 1 Detergent drawer 2 Program knob 3 Washing operation light 4 Start pause and cancel button 5 Spin speed selector 6 Function buttons This button is used for starting a selected programme or putting a programme in progress on pause 0 START PAUSE BUTTON e e 660 FUNCTION INDICATOR LAMPS Pressing the start pause button or any other function button switches on the lamps found above the buttons and the control panel which indicate the wash stages of programmes When any one ofthese lamps is on it means that certain programme is in use The lamp is off when any function button or the start pause button is pressed or the selected function has finished its operation The function indicator lamps are also
5. concerning use of the appliance by a preson responsible for their safety Children should be supervised to ensure that they don t play with the appliance Do not use a multiple socket or extension cord Do not insert a plug with damaged or broken cord into the socket If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard Never remove the plug from the socket by pulling from the cord section Remove the plug by holding Do not plug the power supply with wet hands Never touch the machine with wet hands or feet Never open the detergent drawer while the device is running Never force to open the door of the machine while the machine is running Since the machine can reach high temperatures while running do not touch the drain hose and water during draining In case of any failure first unplug the device and close the water tap Do not attempt to repair Please apply to the nearest authorized service station Do not forget that the packing material of your machine may be hazardous for children Keep your pet away from your machine Your machine should only be used by adults within the information written in this manual Your machine is designed for use in house environment Warranty will be invalid if you use it for commercial purposes Never use or store flammable materials nearby the appliance To clean the appliance do not use flammable cleaning agents The appliance should not be p
6. of the detergent that you will fill in your machine depends on the following criteria e Your detergent consumption will change according to the dirtiness level of your clothes For your slightly dirty clothes do not pre wash and put a small amount of detergent in the compartment no 2 of the detergent drawer For your excessively dirty clothes select a program with pre washing fill portion of the detergent you will put in compartment 1 in the detergent drawer and the remaining portion in compartment 2 In your machine use the detergents developed especially for automatic washing machines The quantities that will be used for your clothes are written on the packing of the detergents As the hardness of your water increases the amount of the detergent to be consumed will also increase As the amount of your clothes increases the amount of the detergent to be consumed will also increase Fill your softener in the softener compartment in your detergent drawer Do not exceed the MAX level Otherwise the softener will diffuse in the washing water via the siphon The softeners with high density should be diluted with some water before filling in the drawer That is because the softener with high density obstructs the siphon and prevents the flow of the softener e You can use fluid detergents in all programs without pre washing For this mount the fluid detergent level plate in the second compartment of the detergent drawer and arrang
7. used for failure codes specified in Section 9 Es FUNCTION BUTTONS Intensive rinse You can have one more rinsing done in addition to the rinses which your machine has made in all washing programs by using this function Start delay The timer function enables you to set your machine to start its wash operation with delay Depending on the delay time you wish the programme to start at press the function button until the desired delay timer lamp 1h 3h 5h 7h lights up on the control panel The lamp above the function button will flash Start the programme by pressing the start hold button Rinse hold This function is recommended to be used when the clothes cannot be taken immediately after the end of the program This will prevent occurrence of wrinkles When this button is pressed the last rinsing water is not drained For the program to continue from the start pause repress the start pause button WARNING If you have forgotten to use an additional function and the machine has started the wash operation press the button of the additional function you wish to select if the indicator lamp above it keeps lighting the additional function you selected will become active If the lamp stays lit for a certain while and then goes out the additional function you selected will not become active NOTE Our products contain electronic cards and touchscreen buttons Lightly pressing on the buttons will suffice to activ
8. FULL ELECTRONIC WASHING MACHINE USER MANUAL THE CONTENTS SECTION 1 BEFORE USING e Safety warnings e Recommendations SECTION 2 INSTALLATION e Removal of transportation screws e Adjustment of feet e Electrical connection e Water supply connection e Water drain connection SECTION 3 TECHNICAL SPECIFICATIONS SECTION 4 CONTROL PANEL Start Pause button Function indicator lights Function buttons Program knob Spin speed selector SECTION 5 WASHING YOUR LAUNDRY e Before washing e Running the machine SECTION 6 MAINTENANCE AND CLEANING e Water inlet filters Pump filter Detergent drawer Siphon plug The cabinet The drum Remove of your machine from lime SECTION 7 PRACTICAL INFORMATION SECTION 8 AVOIDING MINOR FAULTS SECTION 9 AUTOMATIC FAILURE DETECTION SYSTEM SECTION 10 INTERNATIONAL WASHING SIGNS SECTION 1 BEFORE USING DEFINITION OF USE This washing machine is exclusively destined to wash and spin machine washable laundry in quantities which are usual for private households e Observe the instructions given in these Instructions for Use when using the washing machine e Keep these Instructions for Use if you pass on the washing machine to another person also give him her Instructions for Use SAFETY WARNINGS e The appliance is not intended for use by people including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction
9. ate the functions PROGRAM KNOB With the program knob you can select the program with which you desire to wash your clothes You can adjust the program selection process by turning the program knob in both directions You must be careful that the adjustment sign of the program knob is exactly on the program you want to select When you bring the programme knob to 0 off position your machine will carry out the drain operation in order to finish cancel programme cycle After drain is finished machine will go into Standby Mode You can now select another programme you wish to start uel v A2 ft see 0 STOP 1 Cotton 90 2 Cotton 60 with prewash 3 Cotton 60 4 Cotton 40 5 Synthetics 60 6 Synthetics 40 with prewash 7 Synthetics 40 8 Synthetics 30 9 Delicates 40 10 Hand wash wool 30 11 Wool cold 12 Quick wash 30 Rinse Spin xy Drain SPIN SPEED SELECTOR By the spin speed selector knob you can make the adjustment of speed for the process of spinning your clothes The speed adjustment interval is between 0 No spin and the maximum spinning speed of your machine NOTE Do the spinning process of your sensitive and delicate clothes in the most appropriate mode AWG 5122C AWG 3102C AWG 5102C SECTION 5 WASHING YOUR LAUNDRY e Plug the machine e Open the tap water First wash cycle There may be water left inside your machine after factory tests and trials
10. e of solvent to be used Garments bearing these symbols should not be washed in your machine unless the label says otherwise EC Declaration of Conformity The appliance conforms to the following European Standards 2006 95 EC Low Voltage Directive 2004 108 EC Electromagnetic Compatibility Directive 5026 311 02036 52024640
11. e the amount of fluid detergent according to the levels on this plate RUNNING THE MACHINE Program selection and features Select programmes and additional functions appropriate for your laundry with the help of the tables shown on pages 17 Start Pause button Pressing this button you can start the programme you selected or put the programme in progress on pause When the programme you selected starts its operation the lamp above the start pause button will start lighting When you wish to put the selected programme on pause press the start pause button once The lamp above it will start to flash In order to restart the programme from the point it was put on pause at you will have to press the start pause button once again Starting the program e Adjust the programme knob to a programme you wish to select If the programme you selected is a wash programme the wash operation lamp will flash If the programme you selected is a rinse spin or drain programme the lamps indicating the related selection will flash Start the selected programme by pressing the start pause button When you start the programme by pressing the start pause button the lamps will light up indicating that the start pause button is active and the wash operation is in progress Selecting an additional function button e Adjust the programme button to a programme you wish to select e lf the programme you selected is a wash programme the was
12. e valve inlet filter is obstructed Clean the valve inlet filters The door is not shut properly The drain hose is obstructed or bent Shut the door properly You should hear the click Check the drain hose The pump filter is obstructed Clean the pump filter The clothes are not placed inside the machine in a well balanced manner The feet of your machine are not adjusted Spread the clothes inside the machine in an orderly and well balanced manner Adjust the feet Transportation screws are not removed Remove transportation screws See the section concerning the maintenance and cleaning of your machine See the section concerning installations your machine FAILURE Your machine is vibrating Excessive foam in the detergent drawer The washing result is bad PROBABLE CAUSE There is a small amount of clothes in the device Excessive amount of clothes are filled in the machine or the clothes are not placed ina well balanced manner Your machine touches a ripid object Too much detergent has been used METHODS OF ELIMINATION It does not prevent operation of the machine Do not exceed the recommended quantity of clothes and spread your clothes in the machine in a well balanced manner Prevent your machine s leaning on a tough place Press the start pause button In order to stop the foa
13. h operation lamp will light up If the programme you selected is a rinse spin or drain programme the lamps indicating the related selection will light up In order to select an additional function e Press once the additional function button you wish to select If the lamp above the function button keeps lighting it means you have selected the function you wished to select If the lamp above the function button is flashing it means you cannot use that additional function for the wash programme you selected Start the selected programme by pressing the start pause button When you start the programme by pressing the start pause button the lamps will light up indicating that the start pause button is active and the wash operation is in progress Cancelling a programme If you wish a certain programmo in progress to finish early e Press the start pause button for 4 seconds Your machine will carry out the drain operation necessary for the programme to finish and then end the programme The programme end lamp will be on You can now select another programme you wish to select Programme end e Your machine will stop automatically when the programme you selected has finished The programme end lamp will light up Bring the programme knob to the STOP off position The door lock of your machine will automatically release about two minutes after the programme has f
14. hine in a room prone to frost If you must make sure that the washing machine is completely drained after each wash Remove inlet hose s from water tap and let the water flow out completely Remove drain hose from siphon or handwash basin and let the water flow out completely Empty residual water inside the machine by following the instructions in the chapter Draining Residual Water tilt the appliance forward with two persons to let the rest water flow out completely THE DRUM Do not leave metal parts like needles staples or coins inside your machine These pieces cause formation of rust stains in the drum To eliminate these stains of rust use a cleaning substance without chlorium and follow the warnings of the cleaning substance producer For cleaning of the rust stains never use dish washing wires or similar rough objects REMOVE OF LIME FROM YOUR MACHINE If you arrange the amount of the detergent you use in your machine properly there will be no need for lime removal However if you desire to apply the removal procedure use the lime protectors in the market and pay attention to their warnings N WARNING The lime eliminating substances contain acids and this may cause colour modifications in your clothes along with an adverse effect on your machine SECTION 7 PRACTICAL INFORMATION a e o A Alcoholic beverages The stain point should first be washed with cold water than should be wiped with glycerine and water
15. inished You can open the door and take out the laundry by pulling the door handle towards yourself After you have taken out the laundry leave the door open so that the machine interior can dry Unplug the machine Turn off the water tap WARNING In the event power is cut off at any stage of the wash programmes and then resupplied after a certain while your machine will continue the programme from the point it was interrupted at Such a situation will not cause any harm to your machine In the event power is cut off during the wash operation the door lock mechanism will release its hold after two minutes If there is water in the machine do not open the door or the water will pour out If you wish to take out your laundry you can do so by draining the water inside the machine following the instructions explained in the section cleaning the pump filter on pages 18 and 19 Child lock Your machine is equipped with a child lock in order to prevent a programme s operation from being affected by a push on a button during a wash operation The child lock will become active after the first and second function buttons on the control panel are pressed at the same time and for longer than three seconds You can notice the activation of the child lock by checking out the programme wash rinse and spin lamps which will flash for two seconds In order to deactivate it you will have to press the same buttons for longer than three seconds If
16. le for use of lye you can add lye into your washing water For woolen fabric a cloth damped in oxygenated water should be covered on the stain and it should be ironed with a dry cloth on it It should be washed after rinsing well KA add SECTION 8 AVOIDING MINOR FAULTS All repairing which must be done on the machine should be done by authorized service When a repairing is required for your machine or you are unable to eliminate the failure with the help of the information given below e Unplug the machine e Close the water tap e Apply to the nearest authorized service station FAILURE Your machine does not operate Your machine does not receive water Your machine is not draining water Your machine is vibrating PROBABLE CAUSE It is unplugged METHODS OF ELIMINATION Insert the plug into the socket Your fuse is defected Change your fuse The electric power is off Check the electric power Start pause button has not been pressed Press the start pause button The program knob is in O off status knob on the desired Bring the program status The door is not shut properly Water tap is closed Shut the door properly You should hear the click Open water tap The water inlet hose may be bent Check the water inlet hose The water inlet hose is obstructed Clean the filters of water inlet hose Th
17. lothes in cold water for 30 minutes If the stain still does not disappear lay in mixture of water and ammonia 3 table spoons of ammonia in 4 liters of water for 30 minutes Cream ice cream and milk Lay your clothes in cold water and rub the stained area with detergent If the stain has still not disappeared apply lye on the fabric of your clothes in proper proportion Do not use lye on coloured clothes Mould Mould stains should be cleaned as soon as possible The stain should be washed with detergent and if it does not disappear it should be wiped with oxygenated water in proportion of 3 Ink Hold the stained area under cold water and wait until the inky water completely runs off Then rub with water diluted with lemon juice and detergent wash after waiting for 5 minutes Fruit Stretch the stained area of your clothes on the top of a container and pour cold water on it Do not pour hot water on the stain Wipe with cold water and apply glycerine Wait for 1 2 hours and rinse after wiping with a few drops of white vinegar Grass stain Rub the stained part with detergent If the type of fabric is suitable for use of lye wash it with lye Rub your woolen clothes with alcohol For coloured ones a mixture of 1 unit pure alcohol and 2 units of water Oil Paint The stain should be eliminated before it dries by applying thinner on it Then it should be rubbed with detergent and washed Burnt stain If your cloth is suitab
18. lp of an old toothbrush Collect the residues inside the drawer slot without letting them drop into the machine After thoroughly drying the drawer put it back in its place reversing the removal procedure DIAGRAM 1 DIAGRAM 2 SIPHON PLUG Pull out the detergent drawer Remove the siphon plug and clean the residues of the softener thoroughly Fit the cleaned siphon plug in its location Check if it placed properly THE CABINET To clean the outside of the appliance use a neutral detergent and a damp cloth Please be careful not to use material that could damage the exterior surface of your machine WARNING If the machine is installed in a location where the ambient temperature can fall below 0 C do the following when it will not be in use e Plug in the machine e Close the water tap and pull out the water inlet hose or hoses from the tap Place the ends of the water drain and water inlet hoses in a cup on the ground Adjust the program knob to Draining program The program ready light will be on Run the program by pressing the start pause button Unplug your machine when the program is over program end light is on When you complete these proces the remaining water inside the machine will be drained and thus formation of ice in the machine will be prevented When you operate your machine again be sure that the ambient temperature is above 0 C FROST Do not place the washing mac
19. m persists turn off the machine unplug and apply to the nearest authorized service immediately FAILURE PROBABLE THE PROCESS INDICATOR FAILURE TO BE DONE Turn on the tap to the end Water may be cut check it If the problem is still continuing your machine will automatically stop after a while Unplug your machine turn off the tap and apply to the nearest authorized service The pump Clean the pump has failed or filter If the The 1 and 4 the pump filter problem number light is obstructed persists apply to blinks or drain pump the nearest is in open authorized circuit service Your machine will automatically drain the water After your machine has completed the draining process shut down your machine and unplug Close the tap and apply to the nearest authorized service FAILURE CODE The water level in your machine is The 1 and 3 below heater number light The pressure blinks of your water supply may be low or locking There is an The 2 and3 excessive number light amount of blinks water in your machine See the section regarding the maintenance and cleaning of your machine FAILURE PROBABLE THE PROCESS Shut down your The heater machine and of your unplug Turn off machine or your tap and the heat apply to the sensor has nearest failed authorized service Shut down your machine and unplug T
20. m dilute one table spoon of softener in half liter of water and pour it in the detergent drawer Press the start pause button after 5 10 minutes Arrange the amount of the detergent properly in the next washing process Wrong detergent has been used Your laundry too dirty for the program you have selected Use only the detergents produced for full automatic machines Select a suitable program see Table 1 The amount of detergent used is not sufficient Use more detergent according to the detergent FAILURE The washing result is not good The water is drained from the machine as soon as it is filled No water is seen in the drum during washing There are residues of detergent on the clothes There are gray stains on the clothes PROBABLE CAUSE Clothes exceeding the maximum capacity has been filled in your machine Your water may be hard Distribution of the clothes in your machine is not well balanced The end of the water drain hose is in a position too low according to the machine No failure The water is at the lower part of the drum The pieces of some detergents which do not dissolve in water may stick to your clothes as white stains These stains may be caused by oil cream or ointment METHODS OF ELIMINATION Put the clothes in your machine in a manner not to exceed its maximum capacity Use the amount of deterge
21. nt according to the declaration of the detergent producer Spread the clothes inside the machine in an orderly and well balanced manner Place the water drain hose in an appropriate height By calibrating your machine for Rinsing program make an additional rinsing or eliminate the stains After drying with the help of a brush In the next washing operation use the maximum detergent amount declared by the detergent producer See the section concerning instalations your machine FAILURE The spining process is not done or starts with delay PROBABLE CAUSE No failure The unbalanced load control may works in that way METHODS OF ELIMINATION The unbalanced load control system will try to distribute your clothes ina homogenous manner After your clothes are distributed passage to spining process will be realized In the next washing process place your clothes into the machine in a well balanced manner SECTION 9 AUTOMATIC FAILURE DETECTION SYSTEM Your machine is equipped with systems which will both take the necessary precautions and warn you in case of any failure by controlling it self constantly during the washing processes FAILURE CODE FAILURE INDICATOR The 1 and 2 number light blinks PROBABLE FAILURE The door is not shut properly THE PROCESS TO BE DONE Shut the door properly so that you hear the click If the proble
22. ou clean the filters you can fit them the same way as you have removed PUMP FILTER The pump filter system elongates the life of your pump which is used to drain the dirty water It prevents lint to enter the pump Cleaning of your pump filter in every 2 3 months is recommended To clean your pump filter Open the kickplate s cover by pulling the handle Before opening the filter cover place a cup in front of the filter cover to prevent flow of the remaining water in the machine Loosen the filter cover by rotating it counter clockwise and drain the water Remove the foreign materials from the filter Check for the rotation of the pump manually After you have cleaned the pump fit the filter cover by rotating clockwise Put the kickplate cover into the place Do not forget that if you do not fit in the filter cover properly it will leak water Z WARNING Danger of being scalded Since the water inside the pump maybe hot wait for it to cool A C DETERGENT DRAWER Detergents may cause residue buildup in the detergent drawer and in its slot over time Take out the detergent drawer periodically to clean up the accumulated residue In order to take out the drawer e Pull the drawer to its end DIAGRAM 1 Keep pulling by pressing on the siphon lid inside the drawer pulled to its end and remove the drawer from its place DIAGRAM 2 Wash it up with water with the he
23. ps found in the accessories bag DIAGRAM 3 The transportation screws that have been removed from the machine should be kept in hand for any other transportation necessities eu DIAGRAM 2 DIAGRAM 1 ADJUSTMENT OF FEET Do not install your machine on rugs or similar surfaces For your machine to work silently and without any vibration it should be settled on a flat non slippery and tough ground You can adjust the balance of your machine from its feet First loosen the plastic adjustment nut Adjust by rotating the feet upwards or downwards After the balance has been reached tighten the plastic adjustment nut again by rotating it upwards Never put cartons wooden blocks or similar materials under the machine to balance the irregularities on the level of the ground a ea ELECTRICAL CONNECTION Your washing machine works with 220 240V and 50Hz A special grounded plug has been attached to the network cable of your washing machine This plug must definitely be inserted to a grounded socket with 10 ampere The fuse flow value of the electricity line attached to this should also be 10 ampere If you have no such sockets and fuses in your house let it be made by a qualified electrician Our company will not be responsible for any damages that may occur as a result of usage without grounding Insert the machine s plug to a grounded socket which you can ea
24. sly reach WATER SUPPLY CONNECTION Depending on the features your machine may be with single water inlet cold or double water inlet cold hot The white headed hose is for cold water inlet and red headed hose is for hot water inlet valid for machines with hot amp cold water inlet To prevent leakage from the connection joints 1 valid for cold water inlet or 2 valid for machines with hot amp cold water inlet seals are included in the hose packing Fit these seals at the end of water inlet hoses on the tap side Connect the white headed hose to the water inlet valve with white filter and connect the red headed hose to the water inlet valve with red filter latter is valid in machines with hot amp cold water inlet Tighten the plastic parts of the connections with your hand Please call a qualified plumber for safer connections Water pressure of 0 1 1 MPa from your tap will enable your machine to work more efficiently 0 1 MPa pressure means water flow of more than 8 liters in 1 minute from a fully opened tap After connections are completed check for the non leakage of the connection joints by turning on your tap completely Be sure that water inlet hoses are not folded broken or crushed Mount the water inlet hoses to a 3 4 geared water tap Cold water inlet White filter valve Hot water inlet Red filter valve WATER DRAIN CONNECTION Be sure that water inlet hoses are not folded twisted crushed or elongated
25. urn off The motor the tap and has failed apply to the nearest authorized service Shut down your machine and unplug Turn off the tap and apply to the nearest authorized service Shut down your machine and unplug Turn off ire ue The motor the tap and blink has failed apply to the e ve 9 o nearest o KK authorized service The 2 and 4 number light blink The 3 and 4 number light blink The 1 2 and3 Electronic number light card has blink failed FAILURE PROBABLE THE PROCESS If the network voltage is lower than 150V or higher than 260V your machine will automatically stop When the network voltage is recovered your machine will continue its operation Shut down your machine and unplug Turn off Communication the tap and error apply to the nearest authorized service The network voltage is too high or too low The 1 2 and 4 number light blink The 1 3 and 4 number light blink SECTION 10 INTERNATIONAL WASHING SIGNS X c c Washing temperature s Do not wash hand wash ZA Lukewarm iron zal Medium hot iron n Hot iron Do not iron Do not tumble dry Z Hang to dry AN Dry flat Do not bleach Handy to bleach All of these are dry cleaning symbols The letters are to instruct the cleaner what typ
26. ut on a carpet which can block the air ventilation on the bottom side Do not operate the wasing machine at temperatures below 5 C If you want to place a dryer on top of your washing machine first contact our After Sales Service or your specialist dealer to verify if this is possible RECOMMENDATIONS The detergent or softener in contact with air for a long time will dry and stick to your detergent drawer To avoid this put your detergent and softener into the detergent drawer just before washing It is recommended that you use pre washing program for only very dirty clothes Please do not exceed the maximum loading capacity If you will not use your machine for a long time unplug your machine close the water supply and leave the door open in order to keep the inside of the machine dry and for prevention from unpleasant odour As a result of the quality control procedures a certain amount of water may remain in your machine This is not harmful for your machine SECTION 2 INSTALLATION You must pay attention to the following issues before using your washing machine REMOVAL OF TRANSPORTATION SCREWS Transportation screws which are located at the back side of the machine must be removed before running the machine Loosen the screws by rotating counterclockwise by a suitable wrench DIAGRAM 1 Remove the screws by pulling them DIAGRAM 2 To the holes where the transport screws have been removed insert the plastic transport screw ta
27. you press any button when child lock is active button will not be activated and you can see wash rinse and spin lamps flashing for two seconds in order to show child lock is active You can notice the deactivation by checking out the programme end lamp which will flash for two seconds cette Zt Program Detergent Max Dry Load Capacity kg Compart AWG 5102C AWG 5122C AWG 3102C Type of Laundry Explanations 1 COTTON 90 5 3 5 Dirty boil cotton and linen textile 2 COTTON 60 WITH PREWASH 3 5 Very dirty cotton coloured and linen textile Underwears sheet 3 COTTON 60 3 5 Dirty cotton coloured and table cloth t shirt linen textile shirt towel 4 COTTON 40 3 5 Slightly dirty paint to get out cotton coloured and linen textile 5 SYNTHETICS 60 Dirty synthetic or synthetic mixture textile 6 SYNTHETICS 40 WITH PREWASH Tulle and curtain as sensitive laundry 7 SYNTHETICS 40 R Nylon socks blouse Slightly dirty synthetic or synthetic mixture textile 8 SYNTHETICS 30 Slightly dirty synthetic or synthetic mixture textile 9 DELICATES 40 Dirty hand and machine to wash wool laundry 10 HAND WASH WOOL 30 Dirty hand and machine to wash wool laundry All wool laundry 11 WOOL COLD Very slightly dirty cold water hand and machine to wash wool laundry 12 QUICK WASH 30
Download Pdf Manuals
Related Search