SGA-440 User Manual
Contents
1. DO S amp DON TS DO v Do charge the battery whenever possible This will extend the battery life A large number of cycles can be obtained from operating on the batteries but battery lifetime is reduced with frequent discharging v Do inspect all cables particularly the mains power cable on the charger for any damage replace where necessary v Do stow the handset and if fitted with charger the mains power cable when transporting the hoist v Do clean the actuators control box charger battery and handset at regular intervals to remove dust and dirt The exterior of the lift should only be cleaned disinfected and sterilized using isopropyl alcohol Damp a cloth with isopropyl alcohol and wipe down entire exterior of lift No other chemicals and or liquids should be used to clean disinfect and sterilize this lift Caution Take great care to ensure that no liquids get inside the lift This lift is not drip proof or water tight Failure to protect the lift from liquids may result in damage to the lift and or may cause personal injury DON T x Don t allow the batteries to fully discharge before connecting to the charger The batteries are a lead acid gel cell type that can be trickled charged continuously batteries used for standby and have a high current discharge capacity Life is greatly reduced by deep or complete discharging of the bat teries Longer lifetime is obtained by maintaining fully charged batteries x D2. Rear wheel brakes works properly Leg spreading foot pedal works properly Battery is fully charged 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 11 Operation A Caution Visually inspect the floor lift before using for any unusual wear and tear Should any thing look unusual then contact your local representative prior to use Failure to comply with this caution could result in serious injury to the operator the individual being lifted and or damage to the lift Because of the safety function in the actuator the lifting arm and hanger bar can fall down to the height of the spindle Therefore both before and after each lifting operation press the lifting arm down to ensure that it is supported by the actuator This must be done to remove the possibility of the lifting arm falling down and the risk of subsequent injury occurring Charging The On light illuminates when you plug the control box to the power outlet and should turn off when it is unplugged The Charge light illuminates and when you connect the battery to the control box and it is charging also the LCD displays shows the symbol of mains cable plug in as shown in the Figure 20 The Charge light will turn off when the battery is finished charging The lift should be plugged in for charging whenever the lift is not in use to get the max number of cy cles out of the battery An audible battery alarm will sound when approxima
3. followed by moving down for a minimum of 2 seconds Total work made by lifting actuator Work indicator for the lifting actuator measures via ampere usage x seconds in use The work indicator gives very good indication of how worn is the actuator Typical minimum lifetime per formance without abuse of the actuator is 10000 cycles in life test equals to 5 600 000 A x S Total number of over loads Counts the number of times the lifting actuator has been overloaded Resetting of Service interval after service has been carried out Resetting of service is done by pressing 2 buttons Lifting arm UP and lifting arm DOWN on the hand control at the same time for 5 seconds After pressing the buttons for 5 seconds you will receive an audio signal indicating that the timer has been reset The timer will clear the display for service symbol and start counting a new service period 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 19 Technical Specifications SGA 440 Sit to Stand Lift Specifications for SGA 440 Aluminum Sit to Stand Lift 440 Ibs Max load and weight in Ibs and Dimensions in inch Max fs fate e 8 aso ora a4 207 266 2873 23738 a3 2 Max load and weight in kg and Dimensions in cm pk Turning cf me M2 aama 543 354 168 23 81 38 4 Max i facto e e e ree fat 97 5 rva5 5 112 1095 65 eo eo sees 11 6 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 20
4. E E ETE 29 PRISM MEDICAL Owner s Manual jien 45 Progress Parkway Maryland Heights MO 63043 USA Use and Care T pie eee 314 692 9135 F 314 692 7858 Fault Finding Warranty Information CAUTION DO NOT ATTEMPT TO USE THIS EQUIPMENT WITHOUT FIRST UNDERSTANDING THE CONTENTS OF THIS MANUAL Introduction Before using this equipment and to ensure the safe operation of your SGA 440 Sit to Stand lift carefully read this entire manual especially the section on Cautions The SGA 440 is designed to be used in con junction with Prism Medical accessories and slings Please refer to any user guides supplied with these com ponents and refer to them while reviewing this manual Should any questions arise from reviewing this manual contact your local authorized Prism Medical Repre sentative Failure to comply with warnings in this manual may result in injury to either the operator or the in dividual being lifted transferred Damage to the floor lift and or related components may also occur Be sure that the contents of this manual are completely understood prior to using this floor lift Store this manual with the documents included with the floor lift and sling s Contents of this manual are subject to change without prior written notice Overview of SGA 440 Sit to Stand lift The SGA 440 Sit to Stand lift is a lifting aid used by health care professionals to transfer clients The Sit to Stand lift makes it possible to m
5. The SGA 440 Sit to Stand lift and sling s are not toys Do not use it for unsafe practices Do not allow children to play with the floor lift or any of 1ts components e The manufacturer s warranty is voided if persons unauthorized by Prism Medical Ltd will perform work on the SGA 440 Sit to Stand lift e There are no user serviceable parts inside the actuator Do not remove cover screws or open the unit as this will VOID THE WARRANTY e In facilities where more than one operator will be responsible for using the SGA 440 Sit to Stand lift and sling s it is imperative that all such members are to be trained in its proper use A training program should be established by the facility to acquaint new operators with this equipment Never expose the SGA 440 Sit to Stand lift directly to water Warranty does not cover any mis use or abuse of the floor lift system e To maintain optimum function the SGA 440 Sit to Stand lift should be inspected and maintained on a regular basis See the section titled General Inspection and Maintenance e Any accessories used with the SGA 440 Sit to Stand lift including sling s should be checked to ensure that they are in good working order Check for signs of wear or fraying prior to use Report any unusual wear or damage immediately to your local authorized Prism Medical Service Provider e The SGA 440 Sit to Stand lift and associated sling s are intended only for lifting and transfer ring of
6. a person Prism Medical will not be responsible for any damage caused by the misuse neglect or purposeful destruction of the lift and or its associated components e In any circumstances do not exceed the maximum allowable load of this lift Refer to the Specifications section of this manual and or the labels on the side of the lift There is a risk of explosion if the lift is used in the precsense of flammable anaesthetics e Ensure that a clear space is maintained around the lift Move any obstacles out of the way before opereating the floor lift 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 6 Assembly Instructions 1 Place the Carton Packaging box in a clear working area open carefully and remove following items and place on the floor taking care to protect the finish from damage Mast with Boom assembly Base Assembly with Legs attached Battery Pack Control Box and Charging Power Cord Hand Control Tool Kit User Manual and Test Certificate Figure 1 3 Mount Knee Pad Height Adjustment Rod using four screws supplied with lift as shown in Figure 2 and 3 Figure 2 Figure 3 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 7 Assembly Instructions 4 Place the Mast with Boom assembly upright in the tube on the Base assembly as shown in Figure 4 Using Locking Handles secure the lift mast in the desired position on the base as shown in Figure 5 Adjust the position of the locking handles
7. each side of the sling are gen erally attached to the corresponding side of the carry bar Be sure to double check to ensure that the straps are properly attached to the carry bar and that the individual being lifted 1s properly positioned in the sling prior to lifting A Caution Prior to lifting an individual make sure that the straps of the sling are securely placed on the hooks of the carry bar 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 15 Basics in transferring an individual continued Step 5 The individual may now be raised using the UP button on the hand control While lifting is in pro gress the height required in order for the transfer to be completed safely should be closely observed Ensure that the individual being lifted will not be injured by any obstructions during the initial lifting Caution Always use caution when lowering raising an individual who is in the sling of the lift Watch out for and avoid any obstructions that may cause injury to the individual or dam age to the lift Step 6 Once at the correct height the individual can be moved to the desired location Refer to the sections already described in this manual on how to do so Step 7 Once at the desired location the individual in the sling can be lowered raised to the correct height in order to complete the transfer On completion of lowering raising ensure that the individual is properly posi tioned and safely supported prior t
8. equipment serviced on a regular basis as described in the General Inspection and Maintenance Section PURCHASE INFORMATION Product Name SGA 440 Bariatric floor lift Model Serial Date of Purchase Purchased From local authorized Prism Medical Representative Address City Postal Code Telephone No Comments SERVICE INFORMATION Contact the following company for service Company local authorized Prism Medical Representative Address City Postal Code Telephone No Comments 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 25 Service Record History Service Type o Periodic Inspection oc Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken 280425 SGA 440 Owner s Manual Complete this section after each service repair i
9. is in accord ance to the periodic inspection requirements of ISO10535 e Check functional operation of the emergency lowering mechanism e All bolts in connection with the carry bar must be inspected greased and tightened All defec tive or worn components must be replaced e Connection bolts bearings between arm and mast to be inspected All defective or worn com ponents must be replaced e Leg spreading function to be tested and all bolts to be inspected All defective or worn com ponents must be replaced e Check that main actuator is functional 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 23 SGA 440 Sit to Stand Lift Points of Attachment Use the described tools to tighten the bolts on a monthly basis in the areas shown 17mm Wrench Actuator mounting 5mm Allen Key Push Handle 4mm Allen Key Mounting Bracket 3mm Allen Key Mounting Control Box 17mm Wrench Actuator mounting Locking Handle VIF a Uti r aAA fj UEF W000 Ire btto n 4s 4 yy al S ats n mre W CTITOR O Whipp ki Page 24 Rev 11 18 12 280425 SGA 440 Owner s Manual Service Record History Initial Information Complete the following section on Purchase and Service Information as soon as this equipment is purchased Use the service record history to record to any completed service and repairs Ensure that the service record is signed and dated each time it 1s used Be sure to have this piece of
10. pointing in downward direction towards the base as shown in Figure 4 Lifting Actuator is not shown in the figure below to show the tightening of the locking handles 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 8 Assembly Instructions 6 Pull the plastic knob to insert the Knee Pad Assembly into the Knee Pad Height Adjustment Rod and re lease the plastic knob once it aligns with hole on Knee Pad Height Adjustment Rod as shown in Figure 7 and 8 Figure 7 Figure 8 7 Insert the Sling Bar into the Boom of the lift by pulling plastic knob on top of the boom as shown in Figure 9 Make sure that the sling bar locking screw is out from the boom as shown in Figure 10 After inserting the sling bar tight the sling bar locking screw so that sling bar will not be able to come out from the boom Sling Bar Locking Screw 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 9 Assembly Instructions Attaching 2 Point QRS Carry Bar to Lift 8 Remove the screws from the mounting position of push handle on Mast assembly as shown in Figure 11 Insert the screws through the push handle bracket and mount the push handle on the Mast Assembly as shown in figure 12 Figure 11 Figure 12 9 Remove the middle screw from the mounting bracket using 3 mm Allan Key Press the SGA 440 CBJ Care Control Box against the mounting bracket and slide it down The control box should be seated securely on top of the edge of bracket as show
11. SGA 440 by Prism Medical roduc osisanom rai rine 2 VT IG W eaan N 2 Components of the Sit to Stand Lift ee 3 Component LIS E ccesarncndarecieuecanneaiaenccesannandethaawenanndions 4 SPECHICAUONS serienn ET 5 O52 10 16 9 een ae oe ee eee ee eet ne KAA REA RENE EEN eer cere 6 Assembly Instruction ccccceecceeeeseesenseeeeseeseesenseees 7 Operation CHEN GING E EEE E TE EEEE E T 12 E E A EPEE IATE TE E T T TEE 12 Forward MOvemMei cccccccee cece eeeneeeeeeeeeaaes 13 EIEN sratonch cristae sonia totum tiandan cia haxeriinaaiedmetiene 13 Leg Adjustment ccccccccesesseeesseeseneeeeeeanens 14 Raising and Lowering BOOM scceeeeeeeeees 14 Casters and Braking cccceceeeeeeeeeaeeeeeseeees 14 Basics in transferring an individual 0seeeee 15 Emergency Stop amp LOWETING cccceeeeeeee eee ees 17 Control Box Usage Information cceceeeeeeeees 18 Control Box Service Information ccceeeeeeeeeee 19 Technical Specifications cccc cee cece eee eeeeneeenes 20 DO S and DOMIS wessccaiecendvotsnateczacienes etecbaganeetsccaehes 21 Trouble Shooting cccccceceeceeeeeeceeceseseeseeeeseeaes 22 General inspection and maintenance 665 23 Points of Attachment Checklist ccceeeeeee ees 24 Service record NiStOry cccceeceeceeeeeeeeeaeeseeaeeaeees 25 AEE A a AEAEE E E
12. al pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 11 18 12 Page 27 Service Record History Service Type o Periodic Inspection oc Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken 280425 SGA 440 Owner s Manual Complete this section after each service repair inspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Re
13. d the symbol will appear on the display and give user the information about why the lift is stopped kg Ibs If someone tries to use the lift while mains plugged in the symbol will appear on the display The user receives the information about why the lift is not working Usage of lift while charging is not possible The display showing a full battery symbol indicates that the battery is fully charged The display showing a half empty battery symbol indicates that it is time to charge the battery The display showing a empty battery symbol indicates that no battery is completely discharged The display showing a lifting actuator is moving up The display showing a lifting actuator is moving down 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 18 Control Box Service information The control box of SGA 440 lift having LCD display to have some basic service data on the display To get this information press the lifting arm up button on hand control for half a second The information that appears on the display is as shown below Total cycles made by lifting actuator Total work made by lifting actuator A x S Total number of overloads Number of days since last service Number of days between services Total cycles made by lifting actuator One cycle is defined as Moving with load the actuator draws more than 1 5 Amps Moving direction up for a minimum of 5 seconds several activations are allowed
14. dual that is to be transferred Use the procedures for up and down and transferring as described in the sections titled Start Forward Movement and Turning Caution Always use extreme care when moving the lift from one location to another Watch out for and avoid any obstructions that may cause injury to the individual in the sling or damage to the lift Step 2 Prepare the individual being transferred with the appropriate sling Refer to the instructions supplied with the sling that was purchased on how to properly outfit an individual with a sling Caution Always make sure that the sling is correctly fitted and adjusted on each side of the individual so that maximum comfort and safety are achieved prior to lifting Step 3 Once the individual has been outfitted with the sling move the lift so that it 1s positioned directly over the individual and utilize leg opening function if required Lower the carry bar to a height so that the straps of the sling can be easily attached to the carry bar AS Caution Always check to ensure that the lift is correctly positioned directly above the per son to be lifted Caution Check to ensure that the carry bar has no cuts dents or sharp edges that may come in contact with the straps of the sling and cause damage to them Report any concerns to your local authorized representative Step 4 Attach the straps of the sling to the hooks of the carry bar The straps on
15. fication SGA 440 Maximum weight capacity 440 Ibs 200 kg Maximum lifting height 54 3 inches 138 cm Front 3 76 mm Wheels dual wheel castors Rear 3 76 mm w brake Weight of lift 81 Ibs 36 8 kg Total Shipping Weight with Box 96 44 Ibs 43 83 kg B Electrical Specifications SGA 440 lift Lift Motor 24 VDC 10 5 Amps Max Charger Input 100 240 VAC 50 60 Hz 0 4 Amps Max Charger Output 24 VDC 0 65 Amps Batteries 24 VDC 2 x 12 VDC 2 9 Ah Sealed Lead Acid Hand Control Electric Lifting Range 35 4 to 54 3 Lift Weight 81 Ibs Maximum load of the installed floor lift is determined by Maximum Load 440 Ibs referring to the product label located on side of floor lift Duty Cycle 10 use 90 rest Rated Performance 30 lifts at 440 Ibs 10 duty cycle Shipping Storage Conditions Normal Operating Conditions Temperature 40 to 70 C Temperature 10 to 70 C Relative Humidity 10 to 100 RH Relative Humidity 30 to 75 RH Atmospheric Pressure 500 to 1060 hPa Atmospheric Pressure 700 to 1060 hPa 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 5 Cautions Under no circumstance should the SGA 440 Sit to Stand lift and sling s be put in control of a person who has not been properly trained in the use and care of this equipment Failure to adhere to this warning may result in serious injury to the operator and or the individual being lifted transferred e
16. lower Lifting actuator cord 1 is not fully plugged into slot 1 on the control box Lifting actuator is defective Control box is defective Lift cannot spread or close legs Foot Pedal is defective Cannot move lift e Rear caster brake is engaged Casters are defective Cannot tighten Mast into Base tube e Mast locking assembly are defective replace with new Mast locking assembly 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 22 General Inspection and Maintenance A Each Use To be completed by User e All functions on hand control are operational B Semi Annually To be completed at least every 6 months Should any of these items fail the inspection do not use the lift Contact Prism Medical Systems or your local qualified service technician for service e Complete the inspection as noted in the Each Use section above Also check the following e Battery charger functional e Weigh scale functional if applicable e Casters are clean and free of debris e All bolts and attachment points are secure see next page for Points of Attachment e Visual inspection of all weld points and cast components e Check operation of the emergency stop button C Annually To be completed at least every 12 months e Complete the inspection as noted in the Semi Annually section above Also check the following e Perform a working load test of one 1 lifting cycle with the maximum load This
17. n in Figure 13 Mount the Control Box to the mounting bracket using same screw that you removed from the middle of the bracket as shown in Figure 14 Figure 13 Figure 14 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 10 Assembly Instructions 10 To install the battery you will need to press the battery against the bracket and slide it down until it sits straight on top of the control box as shown in Figure 15 Make sure to secure the battery box by latching the battery lock into the bracket as shown in Figure 16 Figure 15 Figure 16 11 Connect all the cables to the control box as shown in the Figure 17 to 19 A Connect the Hand Control connector to the large circle on the left side of the control box as shown in the Figure 17 B Connect the Up down Actuator Cable connector to the second circle Marked No 1 from the left side of the control box as shown in the Figure 18 C Connect the Mains Power Cord to the rectangular outlet on the control box as shown in the Figure 19 Figure 17 Figure 18 12 Please make sure to charge battery before initial use and before each operation of floor lift After assembly check to ensure that The mast is fully locked into position The RED emergency stop button on control box is in the OFF out position Lifting actuator moving up and down with the buttons on the hand control and control box Emergency lowering mechanical and electrical function works properly
18. nd lift Sling Hook Push Handle Mast Hand Control Sling Bar Up amp Down Actuator Knee Pad E gt T wo To T t Ea E ka x w C with Calf Strap Foot Plate Front Caster UIT TH Foot Pedal for Gy Leg Spreading Rear Caster w Brake Leg Rev 11 18 12 Page 3 280425 SGA 440 Owner s Manual Component List The following components are included with your new SGA 440 Sit to Stand lift system e SGA 440 Sit to Stand lift e Hand Control e Floor Lift Integrated Charger e Charger Cord e Owner s Manual e Multi Function Wrenches e 4mm Hex Allen Key Short Arm e 3mm Hex Allen Key Short Arm SLINGS If a sling has been supplied with floor lift then pl refer to the instructions included with the sling ACCESSORIES If additional accessories such as a weigh scale have been supplied with the floor lift then pl refer to the instructions included with those items IMPORTANT Before initial use the floor lift unit must be charged for 4 to 5 hours Refer to section titled Charging Instructions The Hand control must also be connected to the floor lift If it is not connected then pl refer to the section titled Assembly Instructions 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 4 Technical Specifications SGA 440 A Dimensions and Weight SGA 440 lift Speci
19. ng the patient from the floor AN Warning Locked wheels during lifting will increases the risk of the lift tilt over Application If the lift is used incorrectly any warranty or product liability might cease to be valid The Sit to Stand lift must only be used for person lifting and only for persons who including the sling do not weigh more than the stated max weight load If the load exceeds the stated weight limit and if the lift is used for lifting anything but persons then any product liability that Prism Medical might have in connection with insurance warranty maintenance etc will cease to be valid To avoid possible accidents and injury to persons being lifted the Sit to Stand lift must only be operated as described in the preceding pages 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 14 Basics in transferring an individual A Caution The following steps are intended to generally illustrate the procedure involved in the lifting and transferring of an individual from one location to another using the floor lift The manual for the sling that was purchased with the lift should be reviewed in detail prior to attempt ing these steps as the sling illustrated here may not be the same as the one that was purchased Contact your local authorized Prism Medical Representatives if you have any questions or concerns Step 1 Unplug the lift from its charging station or current location and move close to the indivi
20. nspection and or maintenance Photocopy additional pages as required o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 11 18 12 Page 26 Service Record History Service Type o Periodic Inspection oc Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken Service Type o Periodic Inspection o Monthly Inspection Completed By Printed Name Company Remarks amp Action Taken 280425 SGA 440 Owner s Manual Complete this section after each service repair inspection and or maintenance Photocopy addition
21. o removing the straps of the lift from the carry bar A Caution Prior to removing the straps of the sling from the carry bar be sure to check that the individual being lifted is securely supported in the final desired position Step 8 Lower the carry bar sufficiently to allow the straps of the sling to be easily removed from the carry bar Take care not to let the carry bar come in contact with the individual in the sling The straps from the sling can now be removed from the carry bar The lift should then be moved away from the immediate area so that it will not interfere with the removal of the sling from the client Step 9 The sling can now be gently removed from the individual It should then be stored in a safe place for future use Step 10 The lift can now be moved to a safe location until further use or relocated to its original location The lift should be turned off when not in use It is recommended that the lift be left on charge when not in opera tion Refer to the section titled Charging the lift for instructions on charging 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 16 Emergency Stop amp Lowering A Caution The manual emergency lowering system should be used only if the lowering procedures de scribed in the previous section of the manual do not work Should you have any concerns or questions contact your local authorized Prism Medical Representative 4 Caution DO NOT use the lift after the man
22. on t continue to operate the handset by repeatedly pressing the buttons if the lift function will not move or the actuator will not function If this occurs then the actuator has either reached its end posi tion the load is too great or there is a malfunction x Don t exert excessive force on the handset cable as this may break off the wires inside the cable and prevent some or all of the operations x Don t continually operate the hoist functions The system is not designed for continuous operation Continuous Operation will cause batteries to be deeply discharged or to damage the actuator or con trol box by overheating 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 21 Trouble Shooting Should problems arise with the use of the lift review the following chart Find the fault and complete the rec ommended solution If the fault is not found and or the solution does not correct the problem contact your local Prism Medicalauthorized Service Provider for service immediately PROBLEM SOLUTION Lift cannot raise lower control box is not clicking Hand control is not properly plugged in Hand control is defective Control box is defective Emergency button is not pushed in Mains cable is not plugged into the control box Lift cannot raise lower control box is clicking Lifting actuator cord 1 is not fully plugged into slot 1 on the control box Lifting actuator is defective Emergency Lower button on control box does not
23. ove mobility impaired individuals with minimal strain or risk to the caregiver while providing complete safety dignity and comfort for the client The SGA 440 Sit to Stand lift is one of two components that make up this technology The other compo nent the sling is a specially designed fabric accessory that attaches to the floor lift by means of a carry bar and straps and holds an individual while the lift or transfer takes place The sling is generally supplied with the Sit to Stand lift at the initial time of purchase Please refer to any user guides supplied with the sling and reference them while reviewing this manual The SGA 440 Sit to Stand lift has the ability to lift an individual up from one location such as chair then move the individual to another location and finally lower the individual into a wheelchair The functions of lifting up or down are accomplished by pressing buttons on the hand control The hand control is attached to the Sit to Stand lift Due to the design of the Sit to Stand lift system it takes very little effort to press a button to perform the desired motion Please familiarize yourself with the components of the SGA 440 Sit to Stand lift by referring to the diagram on the next page Model Table for SGA 440 Sit to Stand lift Product Code Product Description 280425 SGA 440 Aluminum Sit to Stand Lift 440 Ibs 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 2 Components of the SGA 440 Sit to Sta
24. pair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature o 6 Month Inspection o Repair o Yearly Inspection o Other Signature Rev 11 18 12 Page 28 Warranty This Warranty does not affect or in any way limit your Statutory Rights 1 Prism Medical guarantees all equipment supplied as new against failure within the period of 1 year from date of purchase by virtue of defects in material or workmanship 2 This warranty does not apply to failure attributable to normal wear and tear damage by natural forces user neglect or misuse or to deliberate destruction or to batteries more than 90 days after original purchase 3 This equipment warranty shall be void if the equipment is not serviced by Prism Medical or its authorized service agents in accordance with the manufacturer s recommendations or if any unauthorized person carries out works on the equipment 4 The liability of Prism Medical under the terms of this guarantee shall be limited to the replacement of defective part s to the sales distributor dealer agent person or entity which purchased the equipment from Prism Medical In no event shall Prism Medical incur liability for any consequential or
25. patient unnecessarily A Warning 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 13 Operation Leg Adjustment The legs of SGA 440 lift are mechanically adjustable for opening and closing base width The legs can be opened to enable access around arm chairs or wheel chairs For transferring through narrow doorways and passages the lift legs should be in closed position Leg adjustment is achieved by pressing the foot pedal located at the rear of base To open the legs press down the left side and to close the legs press down the right side as shown below Press Down to open the legs Press Down to close the legs Raising and Lowering the Boom The up and down movement of boom on SGA 440 lift is achieved by a powerful electric actuator which is controlled by hand control The hand control has two button with directional arrows UP and DOWN The actuator stops automatically at the limit of travel in both directions Casters and Braking The SGA 440 lift has two rear casters with brake The rear casters can be braked for rotation lateral move ment and parking To apply the brake press the brake pedal down with your foot To release the brake press the raised pedal towards the wheel During the lifting the rear wheels should remain unlocked so that the lift will move to the patient s centre of gravity The wheels should however be locked if there is a risk of lift moving to the patient For example when lifti
26. te 25 of battery capacity remaining To obtain max life charge the battery at no more than 30 discharge Please Note The battery can be charged whether the Emergency Stop is activated or not Charging Indicator Light ON when Lift is charging gt Figure 20 Display shows Mains Cable Plug in Start The Hand Control has two functions up and down Press down on the symbols to operate the desired function It is not possible to use two functions at the same time An audible alarm will sound once the load becomes too great on the lift This will cause the lifting op eration to stop Do not continue to operate the handset by repeatedly pressing the buttons At this point the lift has reached it s maximum lift This is a purposefully built in safety feature Please Note The emergency stop must be released at all times during normal operation 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 12 Operation Forward Movement To move the lift forward hold onto the handle bar and push forward Alternatively the caregiver can also place one foot on the base tube and push forward with their foot HANDLE BAR BASE TUBE Turning When turning the lift stand on along one side With one hand pull gently on the handle bar and with the other hand push gently away on the lifting arm In this way the lift will rotate around its own axis This movement is performed with a smooth slow action to avoid swinging the
27. ual lowering mechanism has been used The lift must be reset by a qualified lift technician after use Contact your local authorized Prism Medical Service Provider Emergency Stop Push the Emergency Stop button to cut all power on the Floor Lift To resume power release the emergen cy stop button by turning in the direction as indicated by arrows on the Emergency Stop button Electrical emergency lowering raising The lift boom is lowered or raised by pressing the UP and DOWN arrow button on the control box Emergency Stop Button Emergency Raising Button Emergency Lowering Button Fl aie z Mechanical emergency lowering In case of power failure it is possible to mechanically lower a patient placed in SGA 440 lift In order to lower the boom in an emergency situation pull up the red lever located directly on the lift s ac tuator The boom will lower as you press up and hold the lever Release the red lever once you have low ered the boom to a safe position 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 17 Control Box Usage information The control box of SGA 440 lift having LCD display to have some basic usage information on the display Following information will be visible on the LCD display of control box When it is time for service the service symbol will appear on the display will light up and give notice to users about the need for service SERVICE la Wiad If the lift stops because of overloa
28. unforeseeable losses If you have any questions about the manufacture or operation of this equipment please contact Waverley Glen or your local authorized dealer PRISM MEDICAL SS 45 Progress Parkway Maryland Heights MO 63043 USA Phone 314 692 9135 Fax 314 692 7858 Toll Free 1 866 891 6502 www prismmedicalltd com This document conforms to EN ISO 10535 requirements T Trade mark of Corven Health Care Inc Used under licence E amp O E 280425 SGA 440 Owner s Manual Rev 11 18 12 Page 29
Download Pdf Manuals
Related Search