Home

TQSoft Manual

1. e Test Audit Trail The Test Audit Trail shows the Audit Trail that is created when the test is started but is only associated with this test When the Test is backed up the Test Audit Trail if requested see Company Name and General set up options is also backed up so this audit trail follows the test around and is added to no matter which computer you are working from e Test Report Print Preview This allows usual information about the Test such as Machine Details Channel Configurations etc to be printed out this may also be imported into IPReports later e Test Details Test Details shows Test Specification information specific to this Test Once a test is completed critical information such as the cycle number machine name date and time cannot be changed and are greyed out However non critical details can be changed e In the General section for example the Sterilisation temperature can be changed to Disinfector or Target Temperature The Data Listing or Chart can also be reconfigured e In the Calculations section all options can be selected or deselected e In the Probes section locations of probes can be renamed e In the I calcs section new l calcs can be created and applied e Chamber allows basic details but not test critical ones to be amended e Calibration Report and Calibration Check Report allow these to be viewed at any time e Channel Configuration allows the chart label and colour to be amended e Stages performs
2. eSelect Start Logging 57 e Select the correct chamber from the dropdown menu previously set up through Chamber Records and ensure the cycle number is correct then press Next Chamber Name Cycle Number Select a test spac i Test Specification Sienlizing temperature Benchiop B Type 134C E Benchiop S Type 1340 Bram Lab 121C Full Load Media Year Bmm Lab 1271C Media Auto Control Brom Lab 121C Simpitied PRO Quanerty Bron Leb 125 Mixed Discard Auto Control Bram Lab 1260 PRO Mixed Discard vear Grim Lab 1260 Small Load Mined Discard Quarry Emm Lab 134C Fabae Prion Auto Control Demo ENS54 lt 800 ires Demo Facilites Monitoring Demo PHARMA Demo Porous Load Demo Porous Load with Calcs Fluids 1210 12 Probes Fluids 121C 6 Probes Fluids 121C Simpiliad Thermometric Test Lab 121C Fluid Type 12 Probes Lab 121C Fluid Type 6 Probes Lab 1210 Fluid Type Simplibed Thermometric Test Lab 121C Porous Type 12 Probes e Enter a suitable Job Reference then press OK 58 _ Benchtop N type 1340 Job Relerence ermometric Test SL Auto gt Add Testto Repo D More Back e Highlight the logger in the USB cradle showing the green tick Drag and drop into the required location on the left e Set the start time as required then press Program to send this information to the logger Bench
3. For Fluid Load the following stages must be used e Cycle Started e Free Steaming e Heat Up e Equilibration Start e Sterilisation Start e Machine Sterilisation Start e Machine Sterilisation End Cooling e Sterilisation End e Vent e Cycle Complete For Laboratory Loads the following stages must be used e Cycle Started e Negative Pulsing if applicable e Positive Pulsing if applicable e Free Steaming if applicable e Equilibration Start e Sterilisation Start e Machine Sterilisation Start e Machine Sterilisation End Cooling Drying e Sterilisation End e Air Admission For N Type Autoclaves the following stages must be used e Heat Up e Equilibration Start e Sterilisation Start e Machine Sterilisation Start e Machine Sterilisation End Condensing e Sterilisation End e Cycle Complete For B Type Autoclaves the following stages must be used e Cycle Started e Start Pulsing e Heat Up e Equilibration Start e Sterilisation Start e Machine Sterilisation Start e Machine Sterilisation End Condensing e Sterilisation End e Drying e Cycle Complete 64 For Washer Disinfectors the following stages must be used e Cycle Started e Disinfection Start e Machine Disinfection Start e Machine Disinfection End e Disinfection End e Cycle Complete For LTS the following Stages must be used e Cycle Started e Leak Rate e Negative Pulsing e Heat Up e Sterilisation Start e Machine Sterilisation St
4. The calibration file should usually be left as the default Note The Operator name time and date are taken from the computer settings and are not editable these should be checked before continuing Select OK E Please enter calibration details exe Selec cabbration He Calibration Set 1 ha Job Ref MOTE Calibration Equipment test equipment information is now Operator David Brighton eE Date 06 08 2014 Setup menu Time T 10 28 31 e Select which thermocouple you wish to calibrate and turn OFF the Pressure Channel then press OK a ee OK Chann 4 Tmpt Tmp11 C Tmp 1 C Tmp31 FT Tmi W Tmp M Tmp12 M Tmp22 M Tmp32 FT Tmp42 Y Tmp3 M Tmp13 l Tmp23 Tmp33 l Tmp43 Y Tmp4 Tmp14 M Tmp24 FT Tmp34 FT Tmp44 Y Tmp5 M Tmp15 M Tmp25 FT Tmp35 FT Tmp45 i Tmpb Press Tmp26 Tmp36 Tmp46 y M Tmp l Tmp27 Tmp37 C Tmp47 Tmp8 C Tmp18 C Tmp28 FT Tmp38 FT Tmp48 M Tmp9 M Tmp19 C Tmp29 C Tmp33 M Tmp10 M Tmp20 M Tmp30 M Tmp40 OK e Enter the required setpoints and stability parameters The example below shows the standard parameters used along with usual checkpoints for an autoclave 32 e For Automatic Calibration ensure sure the Calibration Automatic and Use Temperature Reference options are selected then press OK If there is no communication between the equipment and TQSoft the Automatic option will be greyed out and calibration should
5. stome e Press _ e Set the flow control method to None e Save changes and Exit e Open TQSoft go to Logger and Select Logger a Eo run F 7 p A J AAA Temperature Ref Data Management Select type of Logges Recorder hari Select Channel Configuration Download a Digrtal lO Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Calibration Adjust Channel Stability and Fluctuation e Find Agilent 34970A from the drop down menu ogge TMI Orion TYPE 2 Kaye KL Portable Digi VALIDATOR 2000 lent 34972A Grant Squirrel 2040 Simulation Anville 825 select which comms portto use e TQSoft will automatically set the correct Baud Rate Databits and Parity 23 o Select the correct Comms Port from the dropdown menu and Press OK Select type of Logger Agilent 34970A il Baud Rate 9600 hd Data Bits Parity N hi Select which comms port to use Com 8002 Invalid port number Coma 8002 Invalid port number Coma 8002 Irvwalid port number Comb 8002 Invalid port number 02 Comb pA toon Invalid port number Invalid port number id port number e Note In this example Com 1 is used but this will vary depending on your PC It is important that the Com port used is number 16 or below e Select the correct Channel Configuration and press OK 24 Setting Up th
6. then an audit database is created and managed for each test record along with the other files for each test record In this case the option Audit Trail on the Current Test drop down menu can be used to view and manage these audit trails It also means that TQSoft will remember which Calibration and Calibration Check record is associated with each test when you backup the data or complete a Report e Audit Trail Archiving is covered in the Advanced Course Test Equipment e Go to Setup and Test Equipment Change Password Edit Security Audit Trail ey Name and General Setup Options Edit Chamber Records Edit Channel Configuration Edit Test Specifications Default Chart Configure Default Data Listing Configure Printer Setup View Saturated Steam Tables Bot Program e This area allows you to fill in details of all test equipment being used multiple types can be recorded and the correct one selected at the start of each test e Highlight Logger Recorder and select New at the bottom right of the box or right click and select ae r Y O Pron Fai Unit e A new datalogger called New1 will appear on the left Highlight this and the equipment details area will show on the right Complete this with correct information and then select Save Changes Test E quipmert B OD Logger Recorder z oer 0 Sand Ma O Teme Pet Uri C Thermal Bath Depcipion O Press
7. CONABIO ie Calibration Seat Job Ref Equiprnenttest NOTE Calibration equipment information is now Operato Daie Brighton ke pt i Test Equipment on Date 06 08 2014 Setup menu Time Cancel DK e Click OK then deselect all the temperature channels and select the pressure channel e Note In this example we are using millibar If you are different units ensure you select accordingly 39 e Standard pressure set points are as follows Low point 500 High point 3500 Check point 3200 All in millibar absolute Ensure the Do low first and Calibration options are selected y E 5 mn H aration Setup ra Stability Low Point 500 High Point neck Point 32 Al Report after Setpoint stability hor minutes Do Low First Report Interval seconds O Do High First Report max deviation allowed Bar Options TM Us Calibration Check Calibration eed e For the low point of 500 select vacuum on the pressure calibrator and use the pump to apply 500 mBA Once the reading is stable press PROCEED and wait for approximately 10 seconds while TQSoft performs the required calculations Note the values displayed in TQSoft for both the Low point and High point are both Voltage readings NOT pressure readings Ct eg SSS Waiting for Low Point Stability at 500 Channel Na ve Slowestto Stability Largest Dewation Reference Channel PROCEED A Select pressure on t
8. Format CSV file ff Analyse Test fw Cale and Limits Repot f Crop Data e Repeat this process for all users Once completed press OK in the bottom right hand corner To complete the New User setup select Setup then Enter Password a Edit Security Audit Trail Company Name and General Setup Options Test Equipment Edit Chamber Records Edit Channel Configuration Edit Test Specifications Default Chart Configure Default Data Listing Configure Printer Setup email View Saturated Steam Tables Bat Program e A Login box appears with a New User box Select New User Press ENTER to finish an entry or ESC to go back Cancel e Click the dropdown and a list of new users will appear Select the correct account and press Enter Press ENTER to finish an entry or ESC to go back New User Cancel e Type in a new ID username and press Enter Note that this is case sensitive e Repeat your ID to Confirm and press Enter e Type in a Password again case sensitive and press Enter e Repeat your Password to Confirm and press Enter e Once the Password Valid Until date appears press Enter again e Now to go Setup and Edit Security again e Highlight the Demo user and then press De activate Then Press OK e You can renew you Password at any time by highlighting on the name and use the Renew Password tick box an
9. Load SAA oosrrentie AC E LOOSE CO e Lo bl E A A AL q o _ e o e e e en OS fea tree riga mort bor LA Les bae i IE I i i cb ot en i wn i 1550 l EATS h s Posten Pulsing PAT CODE CLF Tra 0005417 w i j 1 a l Boo i i SoD i om paa e If you wish to select a different stage line select the correct one from the dropdown e f the time is incorrect e g the button was not pressed at the correct time it can also be amended here e Note If a stage is missed or you wish to insert them after the test has finished a full choice of all possible stage lines is available once the cycle is complete e The Stage line will now appear on both the Chart and Data List e This can now be repeated for all the other Stages Please see the Appendix to see what Stages need to be inserted into the test for different types of Cycles for templates to work correctly in IPReports e Once inserted stage lines can also be moved manually by hovering the mouse over the required line and then clicking and dragging using the Values at Pointer reading to drop it at the correct time e Once the machine has completed the cycle press the Stop Logging button A confirmation that you really wish to stop is then required setup Logger Thermal Bath Temperature Ref Data Management Current Te Y Demo Porous Load 08 08 2014 Equipment test ACO0002 C LOGSYS6 ACO0002 d 150 0 140 0 130 0 120 0 11
10. Reference then press Next A reference to the type of test is useful e g ACT or Thermometric Test 1 when looking for data from this test at a later date Start Logging Porous Load 134C 7 Probes Job Reference Equipment tesi Auto Add TesttoRepot I More F eT he Start Logging button now appears The timer below can be used to delay the start of logging if required e When you are ready to start the cycle click Start Logging Note Logging should always be started using TQSoft before the cycle begins to ensure no data is lost A Sr Loggeng stent Logging Start Logging 00 00 00 433 e Now the test has started select Inputs Display and watch the cycle appear on the chart Entering Stage Lines While Logging e Stage lines can be entered either whilst logging a cycle or once the cycle has completed However entering stage lines into TQSoft in real time removes the need to manually record machine stages using a separate stopwatch and notepad e When the machine reaches the start of a new stage select the Enter Stage button e A box will be displayed and the next stage line programmed into the Test Specification will be automatically selected along with the time at which Enter Stage was pressed If this is correct press OK 43 a a o Aala g w Chipia Heeger Cibbaskon Cheong isp Logger are Ces Ghai Lia Sarum lata Lira Tan Jura phres pir 5 iro Posse
11. T eaa 1E r LaS pamu cpie ACS ABE Iita 17119 103 CALO G75 O T a 17 rob Kath Lett C possum opi ai AR AA ADE fc 1117 104 CLOS TS eS ka 7333 mb Kith Fitt Load 121 Lia EF ANA SOLA Lat ae 3 ON T 105 CALDES 7S A 17792 ol Kieth C ages 151 g ALS SSIS TETES 113 E CALOGS 15 dat A bl Esih Lab 13C Porous Tape 12 Piobei Ep ARA SSNS TTY MEA 107 CAO GS 1S Veeder 2391 mb4 Eethi 19119 E poro cache mu AAA SUES 133215 138 1 108 CAO GSS 0000007 dats OIC ab Distro Pore Load 1348 7 Probes aa A man te w I 14 CALORE eo RODIN achat OO mbr Cuero Pomas Load THE 7 Probes AALS 14 Svea Paidi A LE 10 CAO GS Tr x ODN dat OM art Crear Wither Deurdacioa MOL Probes SARL 1h AiAi Ui Otc 14 CALORS S ua lata DONES amb Dann Wartha Durdscio SOL 7 Probes SARS li AZANZA Mimih MS T CMO GS 7S ua 00D haa DOCE mhr iama Daira Prom Load SAGAS 1A AM Marte 000 113 CALO GS 7 S cD 00007 data DOCE rd Cintra Benchtop H tree THC AACS A stg ors Bd 14 03 00 DOC 114 CAL0635715 e000007 data ODIO E Diarias Lab 121C Porte Top E Proba AMAS A aA 14h 16 E 1Y CALOGS7 S e data DOES pb Chii Tiia Drbsci FSC 12 Pii SAIS 1A S12 az 140823 OOO TIE CALOGS15 Sec 00007 dt ODL ab Chew Wah Dembecion S00 Probes EEES WANE 14 08 16 OCIO TI t LALO asc UT Pd ta ONO E arab Liar Fore Losd 10L r Probes ara 1A ANNAN Z 190059 OE 19 CAL065 190000007 data OO nb Duero Creare PHARMA SAR i avant dakia OONA 119 CAO GSS e ui nh hery Derg PHSF bi 1d aiaa E A 12 CAL OST A ICN bat OC be Dar
12. aT a SI A e raea Habra aa od ne a al hoo i al Seed catbraton He Calibration Set 1 Job Ret Equipmenttest Operator David Brighton NOTE Calibration equipment information is now keptin Test Equipment on Setup menu Date 06 08 2014 Time 10 28 31 ox e Select which thermocouple you wish to calibrate and turn OFF the Pressure Channel then press OR A u i F cay a ri ESL Sr T A Tecate i a Y Tmpl Tmpl11 l Tmp21 T Tmp31 Tmp W Tmp Tmpl Tmp 2 Tmp3 FT Tmp4 lf Tmp3 M Tmp13 M Tmp23 FT Tmp33 Tmp43 W Tmp4 M Tmp14 M Tmp24 Tmp34 C Tmp F Tmp5 M Tmp15 M Tmp25 FT Tmp35 Tmp45 T Tmp26 Tmp36 Tmp46 a Tmp27 Tmp37 Tmp E Tmp28 Tmp38 Tmp48 u Tmp29 T Tmp39 Es M Tmp30 M Tmp40 e Enter the required setpoints and stability parameters The example below shows the standard parameters used along with usual checkpoints for an autoclave e Ensure the Calibration option is checked then press OK Setpoints Stability Low Point Degrees per minute for 2 minutes High Point Allowed deviation from Reference Deg Reference stability centena 10 05 Deg for 1 min Check Pomt 134 7 Report after Setpoint stability for minutes 3 Do Low First Report Interval seconds O Do High First Report max deviation allowed T Options z M Using a Voltage Reference Calibration Check Calibration Cancel e TQSoft now au
13. after a test has started NB Having this checked allows the continuous monitoring check box to be used This will have the effect that TQ Soft will automatically re start logging with the next incremental test number available Having continuous monitoring checked allows the start new file at midnight option to be used e Log off channel and log off temperature can be used to switch off logging when a specified channel has exceeded and then drops below the specified value For Fluid load type of cycles only do NOT use on Porous Load cycles e The Data Listing button allows you to set parameters for the data listing Test Specification 5W0022 pa2 General Calculations Lethality Probes Stages l cale List l cale Specs Custom gt 15 gt 2UNngs tin jag SEUA gal ee i rr i Tempe ature uris lc a Wersiorr z 5 Pressure uris Ba ea zl Date of last revision i Scan Interval secs to AE Use 24 hour clock Estimated test duration 000030 dh A sitchen Edi Notes Report file for this Test Automatic Settings Calibration File r Calibrabon Set 1 Ti Auto slop logging alter ddthhimnm l rors Log off channel Unreal Channel Configuration Log off temperatura Deg Cancel OOF e Use Locations for Column headings is generally not ticked It would say for example Drain instead of Tmp1 depending on the settings in the Channel Configuration e Print Stage Information should be ticked if you wish
14. already exists choose Copy amp Replace 55 Setting Up Wireless Loggers In TQS v6 e Install the Madgetech driver by running the Prelnstaller exe application supplied found in the USB folder Marne Date moditied Type Site de hi 24 07 4114 14 00 File folder de 86 M 07 2014 14 00 Fale foida 31 08 2010 10050 Setup Information 2 KB 7 eS 1 Apyacatenr 180 KB 31 06 2010 1050 Configurstron sett 1 KB 31 08 2010 1050 Security Catalog 9 KE e Open TQSoft and select Logger then Select type of Logger Recorder e _ _ _ _ ___ __ 1 J Select Channel Configuration Download Digital 10 Cakbraton Files Manual Calibration Aust Calibratron Advanced Calibration Calsbration Records Calibration Checking Validation Calibration Checking Records Channel Stability and Fluctuation e From the dropdown box select Battery Loggers Madgetech TMI Gemini ensure Madgetech is ticket then OK Battery Loggers MadgeTech TMI Gemini Madoeiech F Gemini TMI Cancel The Start Logging button will be replaced with a new icon Please see Programming Wireless Dataloggers for more information on performing a test 56 Programming wireless dataloggers through TQS v6 e Select the Wireless Logger button Setup Logger Thermal Bath Temperature Ref Data Management Current Test Not in cycle5 Help About
15. and Decimal Places this should be O if mB or mBA is used 3 if Bar or BA is used or 2 if KPa is used and the chart colour of your choice Press OK E File Name Universal Channel Configuration Select channel file Universal Channel onfiguration Change the name Name Universal Channel Configuration Fis Hare Chant dat Channel details Channel number 16 Labet Press Channel Type INPLIT_TYO 1 PUT yh rebs Jai INPLIT SO Decimal places INPUT _ 300m INPUT _4dto20m4 100_0m_ SFist Chart Codour INPUT TOT Location INPUT TOO INPUT K IHPUT J _ lt Ea Duplicate OK e Note You can create other devices such as Humidity etc in exactly the same method as the Pressure Channel by typing in the Units of your choice 14 Test Specifications Basic e Go to Setup and Edit Test Specifications Select atest spec rs Sterilizing temperature Disinfection temperature EE lt Back New Delete hhext gt e A list of all the Test Specifications appear divided into Sterilising and Disinfection depending on the type of test To view or edit an existing Test Specification highlight it and click next or right click and select edit e To create a new Test Specification press New Note if you want to create a new Test Specification that is very similar to an existing template e g a 2nd Test Specification which is identical to the one already created except the
16. are being used as reference values then this criteria is irrelevant e Once stability has been met TQSoft then calibrates all thermocouples at the same time and then carries out the tracking run e The report duration and interval are used to generate a post calibration report on the calibrated values after High and Low point calibrations The report max deviation allowed is a limit on the difference between each channel s value and the reference value during the report interval i e after the probe has been calibrated If the difference is exceeded the channel will have a FAIL notice appear in the calibration report results section e After the reporting is completed TQSoft then sends a command to the thermal bath to go to the next set point temperature and the process is repeated 33 e Once calibration has been completed on all setpoints a new screen will appear to allow you to view a preview of the calibration report _ Es View Calibration Records from CALOGSYS6 logger1 zs 21 05 2014 E Calibration Set 1 27 05 2014 10 59 25 Test Calibration Set 1 27 05 2014 15 35 38 Test Calibration Set 1 284052014 11 37 56 Test Calibration Set 1 100642014 10 55 4 Calibrabior Set 1 Channel Details Summary Tmpl matthew hardy 10 06 2014 11 31 08 14039 1406 10033 10 Tmp2 matthew hardy 10 06 2014 11 31 08 14039 1407 10033 10C Configure Preview Pie ok
17. tests with different loggers these will all show on the left column Click Next 61 Benchtop N type 134C Date of test 14 07 2014 Start Time 1426 57 Chamber Name Loan Machine Cyle Number 000001_1 Back Delete Next gt e Highlight the connected logger shown in bold type and select Download 1 Tmpl E Diam Js 2 Tmp2 Load lt lt NS8864 1 3 Tmo Resevor lt lt Fesai 16 Press Presea lt lt P28224 1 Date Calbbaaton EIIE Pannan 14 2517 2517 e Change the logger in the USB cradle and repeat the process until all loggers show the green Downloaded arrow then press OK to collate the data from all loggers 62 Benchtop H bpe THC E 3 Tmp3 Resevoir lt lt P28988 1 des 16 Press Pressure lt lt P2822401 e You can now display the chart or datalist in TQSoft by selecting the Chart Display or Data Listing button as normal and enter any required stage lines using the Enter Stage button 63 APPENDIX Required stage lines for use in IPReports e For all Sterilisers the Verification of Calibration Stage is optional For Porous Load the following Stages must be used e Cycle Started e Negative Pulsing e Positive Pulsing e Heat Up e Equilibration Start e Sterilisation Start e Machine Sterilisation Start e Machine Sterilisation End Drying e Sterilisation End e Air Admission e Cycle Complete
18. the entire menu 53 Data Management Migrating to a new PC On the old PC e Insert a memory stick into an available port e Select Data Management then General Tests selected Files y Space required Bytes Target Drive deta FT Enter a Network destination Tests selected Files Space required Bytes Files processed Copy Files Delete Files e Choose which files you wish to copy across Target Drive or Network folder details TF Enter a Network destination 54 Basic Settings which logger heat bath is set to default etc Channel Configurations including labels etc Security Settings user IDs and passwords Calibration Files historic calibration data Chamber Records copies chamber records but not historic data __ Test Specifications including any user defined Test CALOGS YS E e WIN7 05 gt 3 0001_1 3 014775 lll iV Basic Settings Logger Window positions etc fv CHANNEL CONFIGURATION fv Calibration Files iw Chamber Records iW Test Specification Cancel OF e Press OK A folder called Logsys will be created on your memory stick e Safely eject the memory stick from the first PC and insert it into a spare slot on the destination PC e Copy the Logsys folder from your memory card and paste into your C drive When warned that a file with this name
19. the same function as pressing the Stages button see above 51 e Defective Probes If a probe goes open circuit or is redundant e g a duplicate this can be marked as Defective This removes the probe from the chart data list and all calculations Note this does not permi Aln ao OK e Analyse Test If any changes are made that affect calculations made on the data for example in the lethality settings the test should be reanalysed Select Analyse Test and all calculations will be refreshed e Crop Data Selecting Crop Data gives two options e Crop on Cycle Start Cycle Complete removes unwanted data from your test results This is particularly useful if a delayed start is used or for very long cycles that may be left running unattended e Crop and Split after Cycle Complete removes data recorded after the Cycle Complete stage line moving it to a new file which can be accessed through the Historic Tests menu The same file name is used with the additional suffix _s1 Multiple splits can be performed on the same test by moving the Cycle complete stage line the suffix will then reflect this by using _s2 _s3 etc 52 Historic Tests e After a test is completed it is automatically added to the Historic Tests folder e Press the Historic Tests button sa ems jenem CO NC fioe fe 100 CNL Ss Nada 12115 mb Labid C peru geie AS ewe eiea 12115 102 AS
20. using this Test Specification Note that all Stage Lines are available once a cle is complete a ee l ee AO ee paz A A Tr y ian calc List lcacSpece Custom Cycle Started INT 02 00 CODE 1 Negative Pulsing INT 01 00 CODE 5 Positive Pulsing INT 01 00 CODE 6 Heat Up INT 00 30 CODE 12 stentisation Start INT 00 10 CODE 1 3 Machine Stenlisaton Start INT 00 10 CODE 33 stenlisaton End IN T 05 00 CODE 4 Machine Stenlisaton End INT 05 00 CODE 84 Select Stages Air Admission INT 05 00 CODE 26 Cycle Complete INT 00 00 CODE 27 OF e To add or remove stage lines press Select Stages e To delete a stage from this Test Specification simply highlight it on the right hand side and press Delete If a stage is deleted by mistake it can simply be added again 20 e To add a stage line to the Test Specification from the library on the left highlight the required stage on the left and the stage on the right which will follow it then press Insert In this example Leak Test a will be inserted between C cle Started and LOER Fee OS Ad Fossive Stages feet sien fest _ PUT eee Stated INT 02 00 CODE 1 F n IN h CODE 4 Leak Tas 7 Saat ant p2 00 CODE Bl love F Mi COL 1 00 30 CODE 12 Stenkraiion Start INT 00 10 CODE 13 Start Pulsing TINT o Do CODE 5 Machine Stesiliralion Sian INT 00 10 CODE 83 Positive Pulning INT 01 00 CODE 6 Sterlisalio
21. 0 0 f e The Chart will be resized to fill the entire screen regardless of the original x axis parameters 44 Viewing the Data List e To view the datalist either during ac cle c or for a historic test select the Data Listing J button MTS bidgnmbem iie Lagoa Taere fut ar res Pod Date hiusagariara Current Tet LES Fiel Manr e The datalist for the current cycle will be displayed e Full data i e all scans recorded or Summary data based on the time intervals selected through the Stage Line can be selected AE ry bee ee Es a i pl i i a PR TE rr me m1 ts 2407 01 EE A 00 00 00 00 00 05 339 353 00 00 32 00 00 33 35 2 355 331 0 5 21 206 me 334 35 7 338 48 352 00 01 03 36 7 18 M2 287 20 m4 31 7 139 M2 ns 355 3 00 01 33 36 4 358 342 27 4 4 30 7 31 7 4 1 366 324 35 5 352 MA 19 5 19 2 205 20 19m 20 195 19 9 24 4 208 20 738 00 07 33 19 4 EEJ 194 1985 134 19 5 193 18 7 mE 20 1 20 1 AE 00 03 03 19 3 192 492 19 2 192 19 3 12 186 20 6 20 0 195 199 00 03 05 Ringe DNT 00 30 _ 0003 07 _ 193 1953 192 19 2 193 19 3 192 185 20 7 201 20 0 20 00 03 37 19 7 19 7 18 7 98 137 19 8 19 6 150 21 0 204 20 4 23 00 04 07 20 1 13 194 20 4 199 195 ma 192 212 207 20 9 205 00 04 38 20 6 18 205 20 8 205 20 1 EEJ 192 21 8 212 213 206 00 05 09 21 0 195 207 21 4 xo 20 3 20 1 192 227 217 218 205 00 05 40 23 201 212 A7 232 20 8 23 19 3 23 4 224 221 209 00 06 10
22. 08_Install exe and select Run as Administrator The installation procedure is fairly standard with the exception of a printer installation screen near the end it will display a screen with a button titled Setup Now Click to start printer setup This printer installation should be skipped and performed later Insert the red dongle into a USB socket on your PC If the dongle indicator LED doesn t illuminate then locate and right click on C ISL IPReports Tools USB_Dongle setupdrv exe and select Run as Administrator to install IMPORTANT Right click the IPReports logo on the desktop then choose Run as Administrator This will lock down the correct settings Exit IPReports Right click IPReports_1 4_Build0015 Update exe on the CD and select Run as Administrator to install Run IPReports once then exit Make sure that you have a pdf reader on your computer such as Adobe Reader that can be downloaded free from the Adobe website Using windows explorer locate and right click C ISL IPReports Tools IPReportWriterSetup exe and select Run as Administrator This installs a PDF printer that uses the ghostscript driver installed in step 1 Open PReports Select edit gt preferences then choose the IPReportWriter printer Click Save and then Back Insert the TQ Soft CD and follow the installation wizard when prompted selecting C Logsys as the install directory Insert the TQSoft dongle into a free USB slot If
23. 12 38 22 Calibration Set 1 6062007 Fae Calibration Set 1 31 07 2007 10 24 55 Calibration Set 1 31 07 2007 10 26 46 Calibration Set 1 14 09 2007 11 1237 Calibration Set 1 14 09 2007 11 13 44 Cahbration Set 1 154012009 11 21 17 Calibration Set 1 2840142014 14 45 12 Test Calibration Set 1 Ms j i i SA Es te LAME Ar err COWIE r Channel Details Summary Tmpl DavidBrghton 08 08 2014 15 41 45 1 Tmp13 David Brighton 08 08 2014 15 41 45 1 Configure Preview Print OK 48 Pressure Calibration Check e Click on Logger and then Calibration Checking Validation in the drop down menu Select type of Logger Recorder Logger Control Select Channel Configuration Download Digital 10 Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Calibration Adjust Channel Stability and Fluctuation e Enter a suitable job reference and ensure the Calibration File is the same as that used for the test then press OK oar Canton Me sain NOTE Calton T EN equipment information is nov Date 08 08 2014 Setup menu Time e Select the correct pressure channel and press OK e Enter a suitable check point Note This should normally be the same as the check point used for Calibration e Ensure the Calibration Check option is selected and press OK Ist ard Repor
24. 215 m1 211 208 Dm 20 1 ms 19 4 238 ma H7 204 00 06 40 21 5 23 214 20 8 208 19 8 E 198 24 1 218 21 8 295 00 07 10 16 0 16 0 160 16 7 16 0 16 0 158 152 17 5 166 166 16 5 00 07 40 158 158 158 15 8 155 15 8 157 150 TEJ 158 14 154 00 08 10 16 2 163 162 16 3 162 16 3 16 1 154 17 5 189 16 3 18 3 00 08 40 158 168 154 165 15 16 8 164 15 7 175 73 mr 17 1 00 09 10 18 8 16 8 188 163 163 16 9 16 5 16 1 18 1 176 17 5 175 00 09 40 112 172 17 0 17 4 171 17 4 me 16 3 a ma 17 7 177 00 10 10 17 4 74 74 ma 174 74 17 3 16 8 18 7 181 18 0 18 0 00 10 40 17 7 178 17 7 in 77 178 176 164 191 TE 18 4 154 60 11 10 18 0 18 0 173 17 8 173 10 me 172 3 187 18 7 136 ESE 183 184 182 163 182 183 18 7 176 196 13 0 18 5 185 00 12 40 185 18 5 185 TEN 135 18 5 134 178 18 192 19 1 19 1 Ooo 18 7 17 186 187 186 18 7 155 180 20 0 134 TES 133 MA 188 188 18 7 Be 184 ma 187 161 20 4 ias 10 5 194 00 13 40 15 0 185 13 0 193 15 0 15 0 185 182 20 4 197 19 7 135 00 13 58 Pre Ainse TOO 50 00 13 56 Acid Rinse NT 00 30 00 13 57 19 1 TEJ 19 0 19 5 130 18 0 189 182 20 8 198 19 5 198 MM 14 27 19453 TAa 192 1947 141 194 1 t IRJ mA 2301 2 13A a CAT Da is Leth bul intervals Pani Prever Gu atl i Pe oe MR HA es 45 Entering Stage Lines After Completing a Cycle e Once a cycle is complete or an older cycle has been selected through the Historic Tests menu press the Chart Display button to bring up the graph e Press Enter Stage and
25. Fraas Load 1210 7 Probes AALS A Saat iat OS 1H CAO GS 7S ec OF data OSE rd Dara Farar Laad THC 17 Probes Chanba w AMES IBA 1157 35 ue A A ae rae Porat Load THE 17 Probes beg nchar AARNES 1236 TTS an 10 SB 349 EAF el ai de a ad ATA las PTA Par l paa 14r Lote pk Fi snk Cor c O E ai l cs anri nr EuT al Lance Ste fwin7_O5 05 ge or e To filter these results or e the heading selection press Configure From this menu a different source file can be selected and headings can be selected as either Shown or Hidden e Note For IPReports to import data the File Name header must be in the Shown column Double click the header name to move it from one column to the other 9 Historic Test Index Directory source for test and audit records r Filters CALOGSYS Job Reference f O ON c WIN7_05 Chamber T ON Date From TM ON ax LOGSYS Date To ON 9 014775 Copied Files Uncopied Files Show import files 25 HYD UHH Options Keep deleted records Treeview Sot on date then lime MW Automatic list remake Shown Hidden e To view a previously run test either double click the required cycle or select it and then press OK e The cycle number will appear next to the Current Test menu at the top of the page To view information on this cycle use the Chart and Data List buttons or select Current Test to view
26. Probe locations are in different positions you can copy the existing template and then modify the new one For example if you want to use the Porous Load 134C 3 probes Test Specification as the basis for the new one highlight it on the list then press new A message will then appear asking if you wish to use this template as the basis for a new one selecta test spec Porous Load 1210 3 Probes Full Load Porous Load 121C 3 Probes Small Load Porous Load 121C 7 Probes Porous Load 134C 12 Probes Chamber Vall Porous Load 134C 3 Probes Full Load Porous Load 134C 3 Probes Small Load Porous Load 134C 7 Probes Do you want to use Porous Load 134C 3 Probes Full Load as a basis for F the new one wo 15 e New Test Specifications are given a default name for instance SY0022 pa2 Highlight this test then right click and select Edit Select atest spec Porous Load 1340 7 Set Hudd Tube a Sec Lab 100 Freesteaming Auto Control sec Lab 115C Fluids Auto Control Sec Lab 121C Fluids Bijoux Baskets Auto Control sec Lab 121C Full Load Fluids early sec Lab 121C Glassware Auto Control Test sec Lab 121C Simplified PRO Fluids Quarterly sec Lab 126C Plastic Mmed Discard Auto Control Sec Lab 126C PRO Mixed Discard early sec Lab 126C Small Load Med Dis Quarterly sec Lab 1250 Small Load Plastic Disc early ii E Disinfection tet New E Edit Back Delete Dele
27. a list of all possible stages will appear on the left along with all stages entered for this cycle on the right r Hignignt t the required Stage from the list on the left and CALOGS Y SEX AMP LE mb press Insert At Passive St Cycle Slanted INT TF oo CODE 1i Pre Vacuum PAT 02 00 CODE 4 Leak Test Start INT 02 00 CODE 8 Negative Puking INT 01 00 CODE 5 Start Pulsing MNT 01 00 CODE 5 Positive Pulseng PAT 01 00 CODE 6 Free Steam INT 01 00 CODE 7 Heat Up INT 00 05 CODE 12 Equibibration Start PAT 00 10 CODE 37 Sterilisation Start INT 00 10 CODE 13 Machine Sterilisation Start INT 00 10 CODE 83 Ven maton of Calibration INT 00 30 CODE 239 Stenliration End INT 05 00 CODE 14 Machine Sterilisation End I NT 05 00 CODE 84 Condensing INT 05 00 CODE 19 Post Vac INT 05 00 CODE 20 Cooling INT 05 00 CODE 24 Drying A T 05 00 CODE 35 Ait Admission INT 05 00 CODE 26 tages for selection Test 00 00 Cycle Started INT 02 00 CODE in 03 37 Start Pulsing INT 00 30 CODE 5 06 14 Postres Pulzing PHT 01 00 CODE 6 07 44 Aving Stenieing INT CODE 12 06 15 Equibbratio n Start INT 00 10 CODE 37 08 16 Sterilization Start INT 00 10 CODE 13 11 55 Sterilisation End UN T 05 00 CODE 14 0 15 38 Air Admi INT 00 05 CODE z6 17 00 Cycle Complete NNT 00 00 CODE 27 a ERRE Enter the correct time using the format hh mm ss
28. and press OK Fi Historical age insert fo r CALOGSYSEVEXAN y PLES pee _ MIST Silage Yenicston of Calibration INT 00_30 CODE 29 Time 00 09 16 Conci Cance Or e As well as showing the time and temperature at the pointer position the Chart Toolbar can also be used to zoom in to a specific area of the graph create a blank stage line and edit the frequency at which the line labels are displayed on the chart Values at pointer Pointer 00 16 09 C Zoom Bos es ID interval C Box Size 00 10 00 13 8 C Dataline elven fae 46 Calibration Checking Validation Once a test is complete the equipment used should have its calibration checked to ensure that it is still within the required parameters Thermocouples should be placed in the same holes as for Calibration to improve accuracy e Click on Logger and then Calibration Checking Validation in the drop down menu Select type of Logger Recorder Logger Contral Select Channel Configuration Download Digital IQ Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Calibration Adjust Channel Stability and Fluctuation e Enter a suitable job reference and ensure the Calibration File is the same as that used for the test then press OK AOT EAr E Pelee iy NOTE Calibration equipment information
29. art e Machine Sterilisation End Drying e Sterilisation End e Air Admissione Cycle Complete 65
30. ated Stearn Tables Exit Program e TQSoft v6 can support up to 128 channels but most dataloggers have either 16 or 20 Each channel that is to be used needs to be configured correctly e Select a Channel Configuration and give it a name of your choice Universal Channel Configuration is the default e Assuming the input will be from a thermocouple select Input T 0 01 or Type T range 10mV Ensure the units e g C and decimal places are correct for your application It is also possible to change the Label displayed on the chart location and chart colour at this point Once this is eee e a OK o Select channel tle Universal Channel Configuration Change the name Uniwersal Channel Configuration File Name Chanb001 dal Channel details Charnel Type LL rib Decimal places Chat Col van MN Ligc ation Ls gt upton OK e f the Channel Type is changed you will be asked if you wish to copy this configuration to all other probes with a higher number Select Yes if all the thermocouples will be of the same type and you wish to do so 13 e Repeat for all other temperature channels by using the left and right arrows at the bottom e To set up Pressure go to the last channel on your Datalogger For Agilent is would be Channel 16 For Fluke it would be Channel 20 e Select the correct channel Type for Agilent it would be 10V for Fluke it would be 3V Range e Select the units required
31. ature calibrator or thermal bath and depending on the guidelines to which you are working you may also require an independent reference probe TQSoft is capable of communicating with a wide range of temperature baths and thermometers This allows TQSoft to drive the unit controlling the temperature without requiring a manual input If this is coupled with a temperature reference probe that also communicates with TQSoft it also allows automatic calibration of thermocouples removing the need to enter or accept settings at each stage and allowing other work to be undertaken while calibration takes place Setting up the Thermal Heat Source in TQSoft if required eSelect Thermal Bath and then Select type of Thermal Bath Setup Logger Thermal Bath Temperature Ref Select type of Thermal Bath A Thermal Bath Control Stability Criteria pp e Select the correct bath type from the dropdown menu For example for a Jofra CTC320 select JOFRA CTC ITC MTC TQSoft will select the correct Baud Rate Data Bits and Parity automatically e Select the correct Comms port and press OK Note The Comms port must be numbered 16 or below Select type of Thermal Bath Thermal baths JOFRA CTCITC MTC gt Baud Rate S600 Data Bits B x Panty i 3 Select which comms port to use a 8002 IInvahd port number Com 8002 Irwalid port number Com 8002 Invald port number Com 8002 Irwalid
32. be performed manually this is discussed further in the next section Calibration Setup preci Setpoints Stability Low Point 100 10 2 Degrees per minute for 2 minutes High Point i 40 Allowed deviation from Reference 2 0 Deg l Reference stability crtena 05 Deg for 7 mun Check Foint 134 ae Report after Setpoint stability for minutes 5 Do Low First Report Interval 5 seconds O Do High First Report max deviation allowed las Cc Options Source of Reference Value I Automatic Use Temperature Reference Using a Voltage Reference O Use Entered Setpointiz Calibration Check e TQSoft now automatically checks the stability of all the thermocouples and the reference probe e ALL probes selected for calibration must achieve the stability criteria here for example it is 0 2 degrees for 2 minutes e The allowed deviation from Reference is applied as soon as the calibration is calculated If the difference between any uncalibrated probe value and the reference value is greater than this figure then the probe is labelled as a BAD probe in the calibration report and should not be used The allowed deviation is applied at both the Low and High points e The reference stability criteria is simply the biggest drift allowed for the reference value over one minute A countdown is provided for this too and is reset as soon as the reference value drifts too far If entered set points
33. d press OK You can also deactivate any user at any time e Close down TQSoft and re open it The login box will reappear e Type in your ID then your Password to open TQSoft Company Name and General Setup Options e Go to Set up and press on General Setup Options Logger Thermal Bath Temperature Ref Enter password Change Password Edit Secunty Audit Trail Company Name and General Setup Options Test Equipment Edit Chamber Records Edit Channel Configuration Edit Test Specifications Default Chart Configure Default Data Listing Configure Printer Setup email View Saturated Steam Tables Exit Program e Type in the Company Name and this name will be printed out at the top of all the TQSoft documentation such as Charts Data Listings etc e Type in the Computer Name in the System ID so the Audit Trail knows which PC has been used for each application completed e Select the date Format below Companyname Psopharm_ Systemidenifier PB Audit Trail Archiving i Store Cal Cal check reports and Audit records with each Test Signature at end Test and Calibration iv Show calibration summary report for tests W Show calibration resuts tables in calibration reports Show Calc setups in Test Setup report Dale Forma f European dd mr yyy US mmdd yu Aia yyy ened Cancel OK e f the option Store Cal Cal Check and Audit records with Test record in Company Name and General Setup Options is on
34. dress 138 178 245 1 Modet 26404 Cancel Ma e Press OK and connection will be confirmed e Select the correct Channel Configuration and press OK 28 e The Test Equipment Window will now open check that the correct details are entered here and the correct logger is selected then press Quit E oo IO Test Equipment SC Logger Recordar Legpa Fieconder Se al Ho Age res O Temp Ret Unit 12345 O Thermal Bath Descaption Melia O Pressure Pet Unit Marulaciuns ie Mode 26404 ril Hi Hona Cert Ma A Sooo Aer Dae ewww ATA Fari rare e Note If the PC is connected to the internet through the Ethernet cable at any point Windows will automatically attempt to create a working connection for you This may lead to the IP settings being changed back to Obtain an IP address automatically and preventing communication with the NetDAQ In this case simply follow the steps above to reconfigure the IP address to the correct settings 29 Calibrating Thermocouples Calibration of a thermocouple requires at least three temperature points These should be the lowest and highest temperatures likely to be relevant to a test and a checkpoint between these to ensure that all parameters are met across the whole temperature band This calibration data will be used for all tests performed using this calibration file until another calibration is performed You will require a suitable temper
35. e Fluke NetDAQ Logger e Connect the NetDAQ to the PC using the Ethernet cable then power on the NetDAQ The PC now requires configuring to communicate correctly e Insert the TQSoft CD then Open folder to view files when prompted IP AutoPlay a eo er A DVD RW Drive D TOS U Abways do this for software and ganmes Inrsiai or renr program from your media roa Pubesher mot mecie General options import pictures and videos tara Dropbox e Double Click on the Fluke 2680 Folder Mame Date modified Type MIE 4 Files Currently on the Disc 13 1 Poe Sune Grant Squirrel 20a USB 06 12 2011 03 55 File folder de HyperTerminal 23 04 2013 19 05 File folder de Manuals 04 09 2008 01 56 File folder autorun 3 06 2001 09 13 setup Information 1 KB Es setup 26 05 2014 18 39 Application 39 401 KB LP setupdry 24 06 2010 21 18 Application 270 KB ma SETUPDRW64 02 02 2007 18 05 Application 269 KB setupPharmaDemo 17 10 2007 17 55 Application 46 KB a UKEYWDO DLL 20 11 2000 01 23 Application extens gt KB USBKEY 10 12 2001 08 59 Setup Information 3 KB Usbkey sys 05 01 2001 09 01 System file 13 KB l usbkey ved 07 08 2000 04 28 Virtual device driver 11 KB e Double Click on the NTool32 dll file to install the Fluke NetDAQ drivers and follow the installation instructions e When this is complete press Finish e Press the Start button and then open Control Panel e Select Network and Internet Ce
36. e Once you have viewed the calibration report press OK A prompt will appear asking if calibration is now complete If you require pressure it is important to select No and proceed to pressure calibration this allows both sets of calibration data to appear on the same document e Note If you are using IPReports it is unnecessary to print the calibration report as this can be imported automatically into your completed Validation Report 34 Temperature Calibration Manual If there is no communication between available between TQSoft and your temperature bath and or reference probe information about each stage of calibration should be entered manually e Click on Logger and then Calibration in the drop down menu i ee Pe Tt i Bh ae Ama PC QUISION system Select type of Logger Recorder Logger Control Select Channel Configuration Download Digital IO Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Calibration Adjust Channel Stability and Fluctuation e Type a suitable name in the Job Reference box The calibration file should usually be left as the default Note The Operator name time and date are taken from the computer settings and are not editable these should be checked before continuing Select OK 1 a gt ee ee NS a ee a I Y Ma Pp saca af Er EC j PI ten
37. e following folders on the C drive as well as all subfolders and files C Logsys CAISL They will also require full use of any USB slots available Creating a New User in TQSoft e Identify and double click on the TQSOFT icon on the computer screen e Go to the Setup menu in TQSoft and select Edit Security garg creation qatar a Seiwa Lagar Theeraifeth Terpoma in Ce aera Orri Ten be Ao ines pare a 7 in T ym Charge Pme e l F j i fail She nll i Ti EF a El nt i sone e 5 2 Ed Pobra mE i ma pes q z Te Dis Ch Doe RENI Caalti ready ipi toe ae Ter fee Hiriak Apra Pra Pa hi Tempur Mira aed Se DR Cop ee A ll E pra Litt Chris ec cache Pik biri A ee eri eed ees Pee Chae Cord aja nm ea Caw L rig eras Printer lau rial e Seti Savi Tablas Isophieam a Pregam ES la bdo Caca Ap ai Es A aie Ed rl wo REA HET Mn mr F Li pce hua 1 Creda Als ae e Type in each required User name and after each name is entered press the Add to List Button Operatos Hardware setup Test Spec Tests Report Forms Add Signature as New dave brighton 0 Mame John Smrh Add to List dave brighton De Actrvate E Password Controls Password and ID Min Length 3 Password Age Limit days 0 Inactivity Timeout 00 00 0 3 E OF e You will be asked if the new user should be given Administrator Manager or Operator security status This affects which TQSoft settings th
38. e other users i e if two engineers wisitthe same chamber they should both use the same unique folder name You would normally use the Chamber Serial Number or an abbreviation of it but you can use the default folder name shown below poo SS e Enter the details for the chamber The site name when entered will be used to group chambers on the left side of the screen Note that the Ref Code is greyed out and cannot be changed Once this has been done select Save Changes rc Chamber ID Schedules Details Custom Sensors Example Hospital BE 4 cS New Site H i o Serial number Rel Code m EN cio Marma pomel u Pioom reamier Tren Fosta To Department EEJ e If you have multiple chambers at the same site you can highlight a chamber record that has already been entered then select New This allows common details to be pre filled for the new chamber 12 Channel Configuration e Each channel can be set to a wide range of input types depending on the application The most common of these is Type T thermocouple e Select Setup SIS Edit Channel Confi uration _ _ ay Logger Thermal Bath Temperature Ref Data h Enter password Change Password Edit Security Audit Trail Company Name and General Setup Options Test Equipment Edit Chamber Records Edit Test Spec ications Default Chart Configure Default Data Listing Configure Printer Setup email View Satur
39. e user can change but can be amended later if required e The Audit Trail Reason for Change window will appear Type in a reason if you wish then press OK e The New user is added to the Left Hand Side e Highlight the new User The Password Age Limit option forces the user to reset their password after the number of days set If you do not wish to use this feature a maximum of 9999 can be entered Inactivity Timeout is turned off 00 00 00 by default If TQSoft does not detect any button presses or key presses for this amount of time the password window will appear and no other operations will be allowed until the password or a new ID and password are correctly entered If a test is running TQSoft will run as normal but a password must be entered to carry on after the test is completed e Highlight on the User on the left hand side Then click on to Hardware Setup Test Spec Tests to select what the user highlighted can or cannot do in TQSoft For example if you do not want the user to have access to Edit Security the area of the Software we are in now un tick the feature Edit Security in the Setup Section e Note To allow stage lines to be inserted while running a cycle the Stages Real Time option needs to be selected M Start Logging h More iW Test Audit Trail jv Test Report l Test Details W Calibration Records for Test v Chart Display ler anspor fl rata Listing lv Test Notes fe Export to ASCII
40. he pressure calibrator and use the pump to apply 3500 mBA Once stable again press PROCEED and wait approximately 10 seconds while TQSoft performs the required calculations 40 e Repeat the procedure for the Check Point 3200 mBA Note that the displayed reading in TQSoft has now converted to Pressure Units as TQSoft has worked out the conversion Calibration Progress Waiting for First Calibration Check Point Stability at S200 Channel from No Value mB Reference Slowest to Stability 20 3198 Largest Deviation 20 3198 Reference Channel 3200 e When View Calibration Records from is displayed with a new date time group click on print preview to preview a copy of your pressure calibration report e Once calibration has been completed on all setpoints a new screen will appear to allow you to view a preview of the calibration report E View Calibration Records from CALOGSY56Wogger01 z Calibration Set 1 Calibration Set 1 Calibration Set 1 Calbration Set 1 Lalbrator el Channel Details Summary Tmpl matthew hardy 10 06 2014 11 Tmp matthew hardy 10 06 2014 11 31 08 140 39 140 6 31 08 140 39 1407 Congo Che em x e Once you have viewed the calibration report press OK A prompt will appear asking if calibration is now complete e Note If you are using PReports it is unnecessary to print the calibration report as this can be imported automatically into y
41. is now Operator Dawid E righton re in Test Equipment on Date 02 08 2014 Setup menu Time Cancel e Select the correct channels and press OK e Enter a suitable check point and stability parameters Note These should normally be the same as the check point used for Calibration e Ensure the Calibration Check option is selected as well as the Automatic if required and press OK Setpoints Stability 7 Degrees per minute foe 2 imule end Relsrence stability criteria 05 Deg for1 min i Report alter Setpoint stability for minutes Report Interval seconds Options Using a Voltage Reference Calibration Check Calibrator 47 e Follow the same procedure as Calibration see above For a Calibration Check however no low and high point calculations are carried out the check is simply to ensure that no significant drift has occurred since the calibration was carried out e When TQSoft prompts you to say if you have finished checking calibration select No if you wish to carry out a calibration check for pressure e Press OK e When View Calibration Records from is displayed with a new date time group click on print preview to preview a copy of your temperature calibration check report fa ee ee eee ee ee eo A a Lh YW ay her i Lec A i H 1E Eie SEN stale ina g x Py 1h A ELA A Ce E gt pel faia ee Pay a 1 et E a De Pa o ALET m B J 4 26 06 2007
42. ll usually be Calibration Set 1 if you have a single set of thermocouples calibrated e The channel configuration file is the channel configuration that will be loaded and used once the test is started Select the channel configuration file before selecting probes 16 e Sterilising Disinfection Target temperature sorts the Test Specifications on the first screen If the box below marked Stage Analysis is ticked TQSoft will also automatically insert the correct Start and End of stage markers when all probes are above the required temperature Test Specification 510022 pal General Calculations Lethality Custom lcac Specs Anahysis Settings dia SY0022 pa2 Steriizing tempera Temperature units E Vou aaa g Sempercure Pressure units BA Date of leatievition Jo Scan Interval secs il tsi LJ Use 24 hour clock Estimated test duration 00 00 30 dthhmm M Stage Analysis Edil Notes Report he for this Test Automatic Settings Calie ation File EE Calibration Set 1 ha ad Auto stop logging alter mH dd hhc Channel Configuration File Log off channel riversa Channei Corgan sll oaen 0 Cancel ox e The Use 24 hour clock option controls the format of time in the test record If checked time will be stored as actual time of day if unchecked time will be stored as 00 00 00 at the start of the test e Auto stop logging after allows you to automatically switch off logging a set time
43. n End INT 05 00 CODE 14 Free Steam INT 04 00 CODE 7 Machine Stesilicalion End NAT 05 00 CODE B4 Heat Up INT 00 05 CODE 12 Air Admission IN T 05 00 CODE 26 E quibibration Stat INT 00 10 CODE 3 Cycle Complete NT 00 00 CODE 27 Shberilisation Start NT 00 10 CODE 13 Machine Sterilization Start NN T 0010 CODE 83 Wesnficabion of Calibratnon INT 00 30 CODE 29 Sbenlkration End INT 05 00 CODE 14 Machine 5benlrmation End M T 05 00 CODE 84 Condensing IN T 05 00 CODE 19 Post Vac INT 05 00 CODE 20 Cooling INT 05 right ge a Dmg INT 05 0 Aut Admission TINT 05 00 CODE 00 CODE E e By highlighting a stage then selecting Edit it is possible to change the Display Interval for the stage This controls how frequently data is displayed on the Data List while in Summary mode Either enter the required Interval directly or use the arrow buttons to increase decrease the timer Once this is correct press OK Ey Test specification stage edit ES ool tana Negatve Pulsing INT 01 00 CODE 5 Daia display interval 0100 pop E Cancel IF eNote editing the Interval on the left side changes the Interval in the stage library while editing the Interval on the right will affect this Test Specification ONLY and the Interval in the library will remain the same 21 l Calcs List This is covered in the Advanced Training Course except Chart Line e This section of the Test Specification allo
44. n the Reference and measured temperature Adjust the Temperature bath to the correct temperature and wait for the temperature to stabilise e Again enter the correct reading from the Reference as the thermocouples are now calibrated this is now simply a check to ensure that they are within the required parameters Once the stability countdowns have both reached zero press Proceed to enter the final tracking report 37 Cenes Waiting for First Calibration Check Point Stability at 134 00 Countdown on Biggest Dni Deviation last 60 Se Channel Stabdlity No Value C Requirements seconds Slowest to Stability E A IEA IEA EA E Largest Deviation Reference Channel e Once calibration has been completed on all setpoints a new screen will appear to allow you to view a preview of the calibration report o E View Calibration Records from CALOGSYS6 Jogger01 3 16 23 15 Test Calibration Set 1 10 59 25 Test Calibration Set 1 15 35 38 Test Calibration Set 1 11 37 KE Test Calibration LA Channel Details Summary Tmpl matthew hardy 10 06 2014 11 31 08 14039 1406 10033 100 Tmp2 matthew hardy 10 06 2014 11 31 08 14039 1407 10033 10C e Once you have viewed the calibration report press OK A prompt will appear asking if calibration is now complete If you require pressure it is important to select No and proceed to pressure calibration this allows both sets of calibration data t
45. not be used The allowed deviation is applied at both the Low and High points 36 e TQSoft will now perform a tracking run for the time previously specified During this period the uncalibrated deviation from the reference will be displayed at the specified interval Each probe can be viewed individually E by selecting it from the dropdown on the left Calibration Progress Post Calibration Report for Low Point Channel Selected Time Reference Measured Deviation po Reference Calibrated Max Dev 100 33 100 3 0 0 Mis 100 32 100 3 0 0 00 15 12 100 32 100 3 0 0 Report Time to go eOnce the Report timer has counted down to zero TQSoft will automatically begin calibration at the next setpoint The Temperature bath should now be set to this temperature Once stability is achieved the same procedure can be followed again entering the reading from the Reference and pressing proceed when the countdowns have reached Zero a ages O Waiting for High Point Stability at 140 00 Countdown on Biggest Dnit Deviation hannel Stability last 60 irom No Value C Requirements seconds Reference Slowestto Stability 1 140 7 00 50 01 03 Largest Deviation pz 140 7 Reference Channel 140 40 0 00 0 00 PROCEED e A second tracking run report will run and then TQSoft will move to the Calibration Check Point e At this stage the thermocouples have now been adjusted to take into account any temperature variation betwee
46. ntral Pune Adjust your computer s settings View by Cote System and Security Review your computers stetus P Back up your computer Find and fix problems Appearance and Personalization al a Ay Change the theme User Accounts W Change account type Clock Language and Region Change keyboards or cther input methods Change desktop beckoground Adjust screen resobubron Hardware and Sound P View devices and printers d L PER aP MEES Ease of Access 3 Programs S Let Windows suggest settings Ka Uranstell a program Opterare vizual display Get programs 25 e Select Network and Sharing Center User i h Internet Options e Select Local Area Connection View your basic network information and set up connections 3 3 e 1 DB PC 00594 Multiple networks Intemet This computer View your actrve networks Connect or disconnect isopharm local Domain network Unidentified network Connections VMware Network Adapter Public network y Vinen shinai ViAnet Select Properties Internet Enabled 03 40 14 1 0 Gbps 394 407 365 26 e e Highlight Internet Protocol Version 4 TCP IPv4 and then select Properties or LOCA Area Con ECION F rOpErI a ot Sa Connect using E NVIDIA nForce 10710071000 Mbos Ethernet Tranendasion Control Protocol intermel Protocol The default wide area network prot
47. o appear on the same document e Note If you are using IPReports it is unnecessary to print the calibration report as this can be imported automatically into your completed Validation Report 38 Pressure Calibration Calibration of a pressure transducer requires measurement at at least three pressure points These should be the lowest and highest pressure likely to be relevant to a test and a checkpoint between these to ensure that all parameters are met across the whole pressure band This calibration data will be used for all tests performed using this calibration file until another calibration is performed You will require a suitable pressure transducer and pressure reference unit Ml a TA e Click on Logger and then Calibration in the drop down menu a View Channels Select type of Logger Recorder Logger Control Chamt Select Channel Configuration Download Digital 10 Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Calibration Adjust Channel Stability and Fluctuation e Type a suitable name in the Job Reference box The calibration file should usually be left as the default Note The Operator name time and date are taken from the computer settings and are not editable these should be checked before continuing Select OK P rai details C eas i en ET af bration Seed
48. ocol that provides communication across dwerze imercormected networks e Select Use the following IP address and enter 198 178 246 100 as the IP address and 255 255 255 0 as the Subnet Mask General e ee this capability Otheresse you need to ask your network administrator for the appropriate IP settings O Obtain an IP address automatically 8 Lise the folowing IP address P ates Subnet mask 255 255 255 0 Default patera y Obiam ONS server address automaticaly wi Use the following DNS server addresses Preferred DAS server Alternate DHS server vabdate settings upon exit e Press OK then OK again at Internet Protocol window and then close Network Connections 27 e Go fins LES Jata i Shon wee y A had 4 E I AA ma Fe to TQSoft and then Press Logger and then Select Type of Logger Bath View Channels Select type of Logger Recorder Logger Central Temperature Ret Data Management Digital TO Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Cabbratron Adjust Channel Stability and Fluctuation Select on Fluke NetDAQ TQSoft will automatically select the correct IP address and settings Fluke NeADAQ Senes Logger Select Connection Reset Default Connection Mode Isolated TCP Port Number 4369 Base Channel Number 1 IP Ad
49. or Washer Disinfectors e TQSoft includes Saturated Steam Tables From these tables it can calculate the Theoretical Saturated Pressure from a given temperature or visa versa i e what the Theoretical temperature from the Pressure reading assuming the steam was 100 saturated e For readings on the Theoretical Saturation Pressure from any given temperature click on the Saturation Pressure box Data List as shown above and select which temp channel to do the calculations from usually the drain probe e For readings on the Theoretical Saturation Temperature from the given pressure click on the Saturation Temperature box Data List and select which pressure channel to do the calculations from 19 eT he Lethality area is covered in more detail in the Advanced Training Course This allows either F 0 A O or a custom lethality calculation to be displayed on the chart and or data list from any or all probes a wile ee PUE pom y St SPSL ICA IEA gt uN E AA i Perl bi fi PA A eo ss SI NA 2 A ge L Base temperature ano Deg 2 Value Chart to show lethality xis Full lethality in Data Listing Miriam lethality MT Chat MOT Oxalis Min leth channel 7 Data List Min Instant Lethality Chat BB of Datalist Min inst channel 7 Data List Select Probes lad Start lethality cri Deg Cancel OR e The Stages area controls which Stage Lines will be available from the Enter Stages button while a cycle is being logged
50. our completed Validation Report 41 Performing a Test e Click the Start Logging button de aaa Logger ermal emperatureRef O ent Current Test 9528 epeko Tena Baths npea ted Soke semen Cop Te Etab a q Chamber Name Cycle Number Chamber e Enter the correct cycle number for the cycle about to be run Note TQSoft does not allow you to enter the same cycle number twice for the same chamber Chamber Name a ES El cla nicas Chamber e Select an appropriate Test Specification and click Next Lab 134C Fluid Type 6 Probes Lab 134C Fluid Type Simplibed Thermometnc Test Lab 134 Porous Type 12 Probes Lab 134C Porous Type 6 Probes Lab 134C Porous Type Simplibed Thermoametnie Test Leak Rete Test Pertornance Queliftcaton 121C Performance Qualitcaton 134 Pertornance Re Qualfication 121C Perlornance Re Qualfication 134C Porous Load 121C 12 Probes Chamber Vall Porous Load 121C 3 Probes Full Load Porous Load 121C 3 Probes Small Load Porous Load 121C 7 Probes Porous Load 134C 12 Probes Chamber Weall Porous Load 134C 3 Probes Full Load Forous Load 134C 3 Probes Small Load Porous Load 1340 7 Set Hudd Tube Sec Lab 100 Freesteaming Auto Control Sec Lab 115C Fluids Auto Control Sec Lab 121C Fluids Biyjoux Baskets Auto Control Sec Lab 121C Full Load Fluids Yaarty Sec Lab 121C Glassware Auto Control Test 4 Back 42 e Enter an appropriate Job
51. port number Comb 8002 Invalid port number Com 8002 Irivald port nurnber Com 6002 Invalid port number ti e To check communications are working correctly select Thermal Bath and Thermal Bath Control Ensure a temperature reading from the thermal bath is showing then enter a setpoint value send it to the bath and check that the bath changes temperature 30 Setting up the Temperature Reference in TQSoft e Select Temperature Ref and press Select type of Reference Probe e Select the correct Reference Probe from the dropdown menu for example Jofra DT 50 TQSoft will select the correct Baud Rate Data Bits and Parity automatically e Select the correct Comms port and press OK Note The Comms port must be numbered 16 or below e To check communications are working correctly select Temperature Ref and Reference Probe Control Ensure a temperature reading from the Reference Probe is showing 31 Temperature Calibration Automatic e Click on Logger and then Calibration in the drop pou down menu Select type of Logger Recorder Logger Control Select Channel Configuration Download Digital 10 Calibration Files Calibration Advanced Calibration Calibration Records Calibration Checking Validation Calibration Checking Records Manual Calibration Adjust Channel Stability and Fluctuation e Type a suitable name in the Job Reference box
52. t alter Setpoint stability for Report Interval 49 e For the check point of 3200 select pressure on the pressure calibrator and use the pump to apply 3200 mBA Once stable press PROCEED and wait for approx 10 seconds Calibration Progress Waiting for First Calibration Check Point Stability at S200 Spee Channel from No Value mB Slowestto Stability 20 3198 3198 Reference Channel 3200 Largest Deviation a 3198 e TQSoft will ask have you finished Calibration Checking Press Yes e Press OK e When View Calibration Records from is displayed with a new date time group click on print preview to preview a copy of your pressure calibration check report Once a Calibration Check has been performed the test is complete A new test can either be performed or you can move on to PReports 50 The Current Test Menu e After the Test is completed the cycle number of the test appears next to the Current Test Menu By clicking on the Current Test Menu a number of options are available Current Test WDEXAMP Help About Recent selection history Test Audit Trail Test Report Test Details Test Equipment Chamber Sensors Position Calibration Check Report b Calibration Report Channel Configuration Stages Defective Probes Test Notes Chart Data Listing View ASCH file with Wiite WordPad Export to ASCI Format CSV file Analyse Test I Cale and Limits Report Crop Data b
53. te Next gt The General area of the Test Specification allows you to edit a range of basic functions _ Test Specification SY002 pal General Calculations Lethality Probes Stages calc List IealeSpecs Custom Name SY002 pa Temperature units fc Version Pressure units BA Date of last revision Scan Interval secs 1 fC Ui A how clock Estimated test duration dct hhc rn a Edt Notes Heport fe for this Test Automatic Settings g 2 f i l Aubo stop bogging alter d h mi Log off channel T Log off temperature Deg e Name is used to identify the test specification and should be changed to something easily recognisable e Temperature Units and Pressure Units are specified for each test but should match the Channel Configuration e The scan interval is used to set the scan rate of the datalogger It will be constant throughout the test This should usually be set to 1 second The amount of data shown in the data list can be modified elsewhere e Estimated Test duration is used only to size the chart for real time monitoring before the test has started It resizes the chart automatically for you once the test is complete regardless of the number entered here e Version and date of revision is a means of tracking modifications to test specifications e The thermocouple file specifies which set of calibration values will be activated and used when the test is started See advanced course This wi
54. the Dongle does not light up then locate the Dongle Driver in C logsys Dongle Driver and run the setup Fluke NetDAQ 1 After install finishes explore the TQSoft CD through My Computer open fluke2680 Support and then double click NTool32_DLL and run through setup wizard Change IP Address in Control Panel Network and Sharing Centre Change Adapter Settings right click on Local Area Network properties highlight Internet Protocol Version 4 IPV4 properties change IP to 198 178 246 100 and Subnet Mask to 255 255 255 0 press OK and close out Serial Drivers if using the Isopharm USB to Serial Converter and general settings i 2 3 Double click the CDM20824 Setup application to install the serial to USB convertor drivers Go to Start gt Control Panel gt Device Manager gt Ports to see which ports Windows has allocated to the USB to Serial adapter Note TQSoft requires these ports to be numbered 16 or lower Go back into Control Panel and then select Hardware and Sound Power Options Change plan settings on current plan and set both Turn off the Display and Put the Computer to Sleep dropdowns to Never This will prevent the Windows going into hibernation during a test cycle TQSoft and IPReports are now ready to use If you have any queries on the installation please contact Isopharm at 01709 525256 and choose the option for TQSoft IPReports technical support Please note the user will also require full read write access to th
55. thermal qualification A A e E ee rn By lo a Pm wee a a a wa n i a a a aaa J Pe Pe eee eee PP ear Isopharm Limited Thi T 44 011709 52 52 56 www isopharm co uk INDEX e Page 4 TQ Soft and IP Reports Installation and Setup e Page 5 Setting Up A New User e Page 8 Company Name amp General Setup Options e Page 9 Test Equipment Records e Page 11 Chamber Records e Page 13 Channel Configuration e Page 15 Test Specifications e Page 23 Setting Up Agilent Datalogger e Page 25 Setting Up Fluke NetDAQ e Page 30 Setting up Thermal Bath e Page 31 Setting up Temperature Reference e Page 32 Temperature Calibration Automatic e Page 35 Temperature Calibration Manual e Page 39 Pressure Calibration e Page 42 Performing a Test e Page 46 Entering Stage Lines After Completing a Cycle e Page 53 Calibration Checking e Page 51 The Current Test Menu e Page 54 Data Management e Page 56 Setting Up Wireless Dataloggers e Page 57 Programming Wireless Dataloggers e Page 61 Downloading Data From Wireless Dataloggers e Page 64 Appendix Required Stage Lines For Use With IPReports TQ Soft and IP Reports Installation and Setup IP Reports 1 9 TQ Soft 1 2 Insert the IPReports CD and when prompted select Open Folder to View Files Right click gs exe and select Run as Administrator to install Follow instructions in the setup wizard default settings can be used Right click IPReports_ 1 4 Build00
56. this is only important for Autoclave Testing e Chamber Pressure Sensor PRESSURE e Drain Vent Sensor DRAIN or VENT or DISCHARGE e Chamber Free Space Sensor FREESPACE e Test Pack Sensor PACK or LOAD e Top Pack Sensor Top Sheet TOPSHEET e Bottom Pack Sensor BOTTOM e Water Reservoir Sensor RESERVOIR el he Calculations area allows TQSoft to perform a range of automatic calculations on the data and show these on the chart and or data list These are Scan Calculations as opposed to Interval Calculations or l Calcs and therefore are a calculation performed on each scan of data from the datalogger Test Specification Y0022 pal General Calculations stages beac Li cake Specs Custom Dala List Max temp channel Data List Dala List Min temp channel Data List Data List Masarmam temperature Chart MM Minium temperatures M Chat MY r Max Min temperature Chat BE m Average lemperalure C chet BE M Daalia E Average Min M Chat MN Data List Max Average C Chat MM Data List Saturation temperature M Chat MB M DataLis Pressure channel 116 Press Saturation pressure M Chat MB M Dats List Temp channet Cancel OK e Tick the boxes if you want these calculations to be added to your Chart and Data Listing If they are to be displayed on the chart you can choose the colour from the box here e Max Temp Channel and Min Temp Channel are good information for the hottest and Coldest Channels f
57. to see stage data in the Data Listing e Landscape should be used if more than 13 columns are used 17 e The Chart button allows Ou to set parameters for the Chart display fi 1340 Deg M Use 24 hou clock las Stage Analysis Scan Interval secs Estimated test duration Empii pln nE r Automatic as Bi g Universal Channel Configuration Cancel e To change the unit of the Chart select the units you want For example if the temperature is in C then select these units and then enter the Maximum and Minimum Temperature Values required for the temperature axis e If non standard units are required for example Humidity you can type RH into the units and then add your scale and this will be entered onto your chart on the right hand side The Probes area allows you to specify a location for each probe Pressure Cancel e Click on Select Probes and select the channels required by checking the box then press OK 18 Tmp11 Tmp21 Tmp31 Tmp Tmpl2 Tmp22 Tmpa2 Tmp42 l Tmp13 M Tmp23 C Tmp33 M Tmp43 Tmpl4 Tmp24 Tmp34 Tmp44 1E Tmp15 Tmp25 Tmp35 TmpA5 FT Tmp26 C Tmp36 Tmp46 O Tmp17 Tmp27 C Tmp37 C Tmpa7 Tmp18 l Tmp28 Tmp38 Tmp48 e Type in the Location for each probe and press Enter eFor IPReports to perform some automatic thermometric analysis for you specific naming conventions should be used note
58. tomatically checks the stability of all the thermocouples and the reference probe at the first calibration point e ALL probes selected for calibration must achieve the stability criteria here for example it is 0 2 degrees for 2 minutes Once stability is achieved a countdown will start It is important to wait for this to reach zero e The reference stability criteria is simply the biggest drift allowed for the reference value over one minute A countdown is provided for this too and is reset as soon as the reference value drifts too far If entered set points are being used as reference values then this criteria is irrelevant e Once both countdowns have reached Zero enter the reading from the Reference and press Proceed Calibration Progress Waiting for Low Point Stability at 100 00 Countdown on Biggest Dnit Deviation Channel Stability last 60 from No Value C Requirements seconds Reference Slowest to Stability ea 100 5 00 50 0 1 05 Largest Dewation JEZ 100 6 EJ Reference Channel O ABORT PROCEED e The allowed deviation from Reference is applied as soon as the calibration is calculated If the difference between any uncalibrated probe value and the reference value is greater than this figure then the probe is labelled as a BAD probe in the calibration report and should
59. top H hipe 1HE R 1 Tmp1 Damn ii PRET i in Ms ae 2 e Tmp Load Bi F cay 2 Tmo Revo Fe 16 Press Pressure e Put the next logger in the cradle and repeat steps 5 and 6 59 e Repeat steps 5 and 6 until all loggers have been programmed and allocated to a location then press OK Red indicates this logger has been placed in the cradle but not NECTED 7 Benchtop N type 134C ss 3 programmed a r ae 1 Tmp Drain lt lt P28988 1 ie 2 Tmp2 Load lt lt M58854 1 Es 3 Tmp3 Resevor Start Time Es 16 Press Pressure l a fi 170772014 14 35 50 Tick indicates this logger is currently Green indicates this logger has been programmed successfully in the USB cradle Indicates which logger has been assigned to this location Mo Scart 32767 PC Time Zone 1 ara Date of best 14 07 2014 Start Time 14 25 17 sala e The screen will revert back to the TQSoft home screen Your loggers are now programmed and ready to put into the chamber Logging will start at the time specified so ensure that the cycle is started after this 60 Downloading data from wireless loggers through TQS v6 e Select the Wireless Logger button e Select Download Tests e Highlight the test you wish to download This will also show you which loggers have been allocated to this test If you have started multiple
60. ure Rat Urini Manufacturer e New will now be replaced by the serial number and description of the new logger Highlight this right click and choose Select to mark this as the default datalogger for future tests Audit Calibrations Audit Tests Delete e Continue this process for all relevant equipment then Quit 10 Chamber Records formerly Machine Records e Go to Setup and Edit Chamber Records Enter password Change Password Edit Security Audit Trail Company Name and General Setup Options Test Equipment Edit Channel Configuration Edit Test Specifications Default Chart Configure Default Data Listing Configure View Saturated Steam Tables Exit Program e A box showing current sites will appear Either select Chamber then New at the bottom right or right click Chamber and select New ka te E L K Fiery ea a de Example Hosp ai 11 e You will be asked to enter a reference number for the new chamber The default will start ACOOOxxx Isopharm would recommend changing this to either the serial number or some other recognisable reference as this reference will be used to refer to the chamber later Each chamber needs a unique reference This is used as a folder name on the hard disk for data storage Ifyou are using this logging system as part of a team itis important to co ordinate the chamber folder name with th
61. ws you to insert a line on the chart to indicate your Lower er and SuperHeat Limits e Highlight Default Sterilisation Limits 1 then select l Calc Specs e Enter Start Stage as Cycle Started and End Stage as Cycle Complete e Click on Limit Values e Enter your Upper and Limit values For example for a 134C Porous Load type in 134 for the lower limit 137 as the upper limit and C as the Units The line colour can also be selected here _ Test Specification 510022 pal Chart Line DEFAULT STERILIZATION LIMITS 1 Interval spec Limi values Actori Taget value B Show liri line on chat Upper limit 137 FC Use Color on Data List Lowi fa e e Lale Cancel OK e Press on Calcs List again and select Super Heat Limit e If this is not required e g for a Washer Disinfector press Delete otherwise follow the same procedure again entering the appropriate Super Heat temperature e g 142 C for a 134 C Porous Load cycle l Calcs Specs This is covered in the Advanced Training Course except Chart Line 22 Setting Up the Agilent Logger e Using the Agilent front panel configure the data output as follows ser stoma Se a i A e Press together e Select the RS 232 interface using rotary selector not GPIB STORCL e Press e Set 9600 as the baud rate llo STO RCL e Press e Set the parity and number of data bits as None 8 data bits

TQSoft Manual

Contents

Download Pdf Manuals

Related Search

Related Contents