LRP-101U-KIT User`s Manual
Contents
1. Functions LRP Injector LRP Extender LRP 101CH LRP 101CE Power Input RJ45 with 802 3at af PoE input BNC with DC power over coaxial input Power Output BNC with DC power over coaxial output RJ45 with 802 3at af PoE output Installation Instructions Step 1 Connect the LRP Injector LRP 101CH and LRP Extender LRP 101CE to ends of BNC terminated coaxial cable Stick the Warning Sticker on the coaxial cable Step 2 Connect Cat5 6 UTP cable to LRP 101CH and IEEE 802 3at compliant PoE Switch or PoE Injector If the PoE switch or PoE injector is powered on already then the PWR LED of LRP 101CH and LRP 101CE should lit up immediately Step 3 Connect Cat5 6 UTP cable to LRP 101CE and IEEE 802 3at af complied PoE IP camera or PoE Wireless AP NA Warning The LRP 101CH accepts IEEE 802 3at equipment for optimal power injection The other non standard PoE power devices may cause the LRP 101CH to malfunction 1 Before installation please consider the distance and watts value demand for PD devices The LRP 101C KIT PoE powers output capacity and upload download performance depending on the length of coaxial cable 2 As there are various resistance values in the category of RG 59 U or RG 6 U cable the actual data rate will vary on the quality of the copper wire and environ mental factors Type 2 One L2. UBESESESEES User s Manual x 1 Warning Sticker x 1 For LRP 101U KIT 1 Port 10 100TX PoE PD 1 Port UTP Long Reach PoE Injector LRP 101UH x 1 1 Port 10 100TX PoE PSE 1 Port UTP Long Reach PoE Extender LRP 101UE x 1 Long Reach PoE User s Manual x 1 Warning Sticker x 2 Warning Sticker x 1 1 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them again to repack the product in case there is a need to return it to us for repair 1 2 Introduction of Long Reach Power over Ethernet PLANET LRP 101C KIT and LRP 101U KIT series PoE over Coaxial Extender and PoE over UTP Extender are designed to extend IP Ethernet transmission and inject power over an existing coaxial UTP or twisted pair cable or for distance up to 1000m 3280ft to PoE IP camera PoE wireless AP and any 802 3af at complied powered device PD It is a perfect solution for sending IP video links and power to remotely installed PoE IP cameras that are beyond the 100 meters distance limit of Ethernet Power over Coaxial UTP or Twisted pair cable The Long Reach PoE solution allows Ethernet Data and PoE or PoE to be transmitted using coaxial UTP or twisted pair cable Based on IEEE 802 3at Power over Ethernet Plus and up to 25 watts of power output PLANET Long Reach
3. 2 2 2 LRP 101CE Front Panel and Rear Panel Figure 2 3 and Figure 2 4 show the front and LRP 101CE Long Reach PoE over Coaxial Extender LRP 101CE tr IN Long Reach PoE Extender Coax Figure 2 3 LRP 101CE Front Panel LNK PWR rear panels of the 10 100BASE TX 2 2 3 LRP 101CE LED Indicators Figure 2 4 LRP 101CE Rear Panel System LED Color Function PWR Green Lit indicates the power is on LRP Coaxial Interface LED Color Function INK reds Lit indicates that the coaxial link is established Off indicates that the coaxial link is down RJ45 10 100BASE TX Interface LED Color Function PoE in Use Amber Lit indicates the RJ45 Port is providing PoE power LNK ACT Green Blink indicates the extender is actively sending or receiving data over that port 198 2 3 LRP 101UH 2 3 1 LRP 101UH Physical Dimensions LRP 101UH dimensions W x D x H 94 x 70 3 x 26 2 mm Rear Panel 68 5 PoE IN LNK ACT 48 56V DCIN m m mM o JE QJ ec 10 100BASETX Top Panel 70 3 Bottom Long Reach Power over Ethernet 4 N Qu JT Lf t LRP 101UH rm QJ D cu Long Reach PoE Injector UTP Front Panel 2 3 2 LRP 101UH Front Panel and Rear Panel Figure 2 5 and Figure 2 6 show the front and rear panels of the LRP 101UH Long Reac
4. White Blue 6 Green 7 White Brown 8 Brown SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Orange 2 Orange 3 White Green 4 Blue 5 White Blue 6 Green 7 White Brown 8 Brown SIDE 2 1 White Green 2 Green 3 White Orange 4 Blue 5 White Blue 6 Orange 7 White Brown 8 Brown Figure A 1 Straight through and Crossover Cable Please make sure your connected cables are with the same pin assignment and color as the above picture before deploying the cables into your network 35 1 GQ PLANET Networking amp Communication EC Declaration of Conformi For the following equipment Type of Product 1 Port 10 100TX PoE PD 1 Port Coax Long Reach PoE Injector 1 Port 10 100TX PoE PSE 1 Port Coax Long Reach PoE Extender 1 Port 10 100TX PoE PD 1 Port UTP Long Reach PoE Injector 1 Port 10 100TX PoE PSE 1 Port UTP Long Reach PoE Extender Model Number LRP 101CH LRP 101CE LRP 101UH LRP 101UE Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C We hereby confirmed that the products mentioned comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility 2004 108 EC For the e
5. 101UH LRP 101UE Power Input Power adapter with UTP with DC power over pur 48 56V DC in UTP input Power UTP with DC power over RJ45 with 802 3at af PoE Output UTP output output Installation Instructions Remove the Danger No Ethernet labels stuck on Step 1 the RJ45 LRP ports of LRP 101UH and LRP 101UE Connect the LRP Injector LRP 101UH and LRP Step 2 Extender LRP 101UE to ends of RJ45 terminated long UTP twisted pair cable 1 Please do not connect any Ethernet equipment to LRP OUT Port of the LRP 101UH otherwise it will damage the Ethernet equipment 2 Please do not connect any Ethernet equipment to LRP IN Port of the LRP 101UE otherwise it will damage the Ethernet equipment Connect Cat5 6 UTP cable to LRP 101UH and non PoE SEP E switch or workstation Connect 48 56V DC power adapter to LRP 101UH power Step 4 socket and then the PWR LED of LRP 101UH and LRP 101UE should lit up immediately Connect Cat5 6 UTP cable to LRP 101UE and IEEE Sap a 802 3at af complied PoE IP camera or PoE Wireless AP 1 Before installation please consider the distance and watts value demand for PD devices The LRP 101U KIT PoE powers output capacity and upload download performance depending on the length of UTP cable 2 As there are various resistance values in the cate gory 5 5e cable the actual data rate will vary on the quality of the copper wire
6. Frame 1522bytes sizes 13E Long Reach PoE Interface 1 x RJ45 connector Long Reach PoE over 1 x RJ45 connector Long Reach PoE over Connectivity UTP PSE UTP PD Powered Power Source Device Equipment Power Input 37 56V DC Power Output 41 56V DC RJ45 PIN 1 3 5 7 VCC Power Pin RJ45 PIN 1 3 5 7 VCC assignment RJ45 PIN 2 4 6 8 VCC RJ45 PIN 2 4 6 8 VCC Cabling UTP cable Maximum Max 100m with PoE output 328 ft distance Max 400m with PoE output 1 312 ft Max 500m without PoE output 1 640 ft Long Reach Ethernet IEEE 1901 Standard Modulation Type Wavelet OFDM Security 128 bit AES encryption Frequency Band 2 28 MHz Encryption AES 128 bit LRP 101UE 802 3af at Data Rate PoE Output Capability Distance Upload LRP 101UH LRP 101UH Download w 56v DC w 30W IN PoE IN Performance 1100m 94 94 Mbps 30W 19W 200m 82 82 Mbps 30W 18W 300m 63 67 Mbps 30W 17W 400m 44 48 Mbps 22W 14W 500m 30 30 Mbps 18W 12W 4 x LEDs 4 x LEDs W PWR W PWR LED Indicators W LRP LNK m LRP LNK W PoE IN W PoF in use W LNK ACT W LNK ACT ESD Protection 2KV DC EFT Protection 2KV Enclosure Metal case Installation Wall mount or DIN rail with optional kit Dimensions W x D x H 94 x 70 x 26 mm Weight 193g 190g Power Requirements W RJ45 PoE Input 802 3at a
7. Power over Coaxial Input 44 56V DC Standards Conformance Standards Compliance IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3af Power over Ethernet 802 3at Type 1 IEEE 802 3at Power over Ethernet 802 3at Type 2 Regulation Compliance FCC Part 15 Class A CE Environment Temperature Operating 20 70 degrees C Storage 40m75 degrees C Humidity Operating 5 95 Non condensing Storage 5 95 Non condensing 1 Upload LRP 101CE to LRP 101CH Download LRP 101CH to LRP 101CE 2 As there are various resistance values in the category of RG 59 U or RG 6 U cable the actual data rate will vary on the quality of the copper wire and environment factors Depending on what the DC PoE Power Input and the length of coaxial cable are 1 4 2 LRP 101U KIT Specifications Model LRP 101UH LRP 101UE Hardware Specifications Ethernet Interface 10 100BASE TX RJ45 C LEE Auto negotiation Auto MDI MDI X Power over IEEE 802 3at af PoE PD IEEE 802 3at af PoE Ethernet Powered Device PSE Power Source Standard Equipment Supports both Mid Span and End Span PSE PoE Input ele Input Range 48 56V DC 48 56V DC 600mA PoE Output 1 i max PoE Budget Up to 25 watts End span RJ45 Pin PoE Mode 1 2 3 6 Data Rate 100 100Mbps Cabling Cat5e or above Maximum Distance un Maximum
8. and environmental factors 3 POE Output Capacity is based on different DC Power Input PoE Input 4 The LRP 101UH has two power input options only one mode is available at one time PoE power input cannot be used if power input of DC 52V or 56V is selected 3 6 Optional DIN Rail Mounting There are two DIN Rail holes on the left side of the Long Reach PoE over Coaxial UTP Extender Kit that allow the device to be easily installed with DIN Rail mounting The PLANET optional DIN Rail mounting Kit RKE DIN can be ordered separately When you need to replace the wall mount application with DIN Rail application on the Long Reach PoE over Coaxial UTP Extender Kit please refer to following figures to screw the DIN Rail on the Long Reach PoE over Coaxial UTP Extender Kit To hang the Long Reach PoE over Coaxial UTP Extender Kit follow the steps below Step 1 Screw the DIN Rail on the Long Reach PoE over Coaxial UTP Extender Kit You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect fe I M screws would invalidate your warranty 4 TROUBLESHOOTING This chapter contains information to help you solve issues If the Long Reach PoE over Coaxial UTP Extender Kit is not functioning properly make sure the Long Reach PoE over Coaxial UTP Extender Kit is set up according to instructions in this manual What is the maximum distance supported by LR
9. 4 Applications of LRP 101C KIT with coaxial cable 25 3 5 Applications of LRP 101U KIT with UTP Twisted pair Cable 28 3 6 Optional DIN Rail Mounting iiiter text aa 31 4 TROUBLESHOOTING 2 2 rino to tae inen a oa pri perna cp og vos caesa ese co ao dk RES 33 APPENDIX A NETWORKING CONNECTION een 34 A 1 Switch s RJ45 Pin Assignments wa me 34 A 2 RJ45 Cable Pin Assignments eee 34 1 INTRODUCTION Thank you for purchasing PLANET Long Reach PoE over Coaxial UTP Extender Kit the LRP 101C KIT and LRP 101U KIT The descriptions of the four models are as follows 1 Port 10 100TX PoE PD 1 Port Coax Long Reach PoE Injector LRP 101CE 1 Port 10 100TX PoE PSE 1 Port Coax Long Reach PoE Extender 1 Port 10 100TX PoE PD 1 Port UTP Long Reach PoE Injector 1 Port 10 100TX PoE PSE 1 Port UTP Long Reach PoE Extender LRP 101CH LRP 101UH LRP 101UE Long Reach PoE over Coaxial UTP Extender Kit mentioned in this Manual represents the above four models 1 4 Package Contents Open the box of the Long Reach PoE over Coaxial UTP Extender Kit and carefully unpack it The box should contain the following items For LRP 101C KIT 1 Port 10 100TX PoE 1 Port 10 100TX PoE PSE 1 Port Coax PD 1 Port Coax Long Long Reach PoE Extender LRP 101CE x Reach PoE Injector 1 LRP 101CH x 1 PLANET Long Reach PoE
10. DC m BNC shield DC Coaxial cable 75 ohm Cabling RG 6 U cable less than 129 1000 ft RG 59 U cable less than 300 1000 ft Maximum Max 200m with PoE output 656ft Distance Max 600m with PoE output 1968ft Max 1200m without PoE output 3 937ft Long Reach Ethernet IEEE 1901 Standard Modulation Type Wavelet OFDM Security 128 bit AES encryption Frequency Band 2 28 MHz Encryption AES 128 bit LRP 101CE 802 3af at Data Rate PoE Output Capability Distance Upload LRP 101CH LRP 101CH Download w 56v pc w 30w IN PoE IN Performance 590m 93 93 Mbps 29W 16W 400m 93 93 Mbps 22W 14W 600m 87 91 Mbps 13W 10W 800m 75 83 Mbps 10W 8w 1000m 55 73 Mbps 8W 7W 1E Long Reach PoE Interface LRP Compatibility LRP 101CE 1 Port LRP Extender With power over coaxial input W LRP 101CH 1 Port LRP Injector W LRP 822CS 8 Port LRP over Coax Switch W LRP 1622CS 16 Port LRP over Coax Switch 4 x LEDs 4 x LEDs W PWR m PWR LED Indicators W LRP LNK W LRP LNK W PoE IN E PoF in use m LNK ACT W LNK ACT ESD Protection 2KV DC EFT Protection 2KV Enclosure Metal case Installation Wall mount or DIN rail with optional kit Dimensions W x D x H 94 x 70 x 26 mm Weight 200g 375g Power Requirements m RJ45 PoE Input 802 3at af 48 56V DC W DC Input 48 56V DC BNC
11. Long Reach PoE over Coaxial UTP Extender Kit LRP 101C KIT and LRP 101U KIT User s Manual Trademarks Copyright PLANET Technology Corp 2015 Contents are subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This eguipment has been tested and found to comply with the
12. P 101C KIT PoE powers output capacity and upload download performance depending on the length of coaxial cable 2 As there are various resistance values in the category of RG 59 U or RG 6 U cable the actual data rate will vary on the quality of the copper wire and environ ment al factors 3 PoE output capacity is based on different DC Power Input PoE Input 4 The LRP 101CH has two power input options only one mode is available at one time PoE power input cannot be used if power input of DC 52V or 56V is selected 3 5 Applications of LRP 101U KIT with UTP Twisted pair Cable Type 1 LRP 101UH with PoE power input and LRP 101UE with PoE power output LRP 101UE p qmd 802 3af 802 3at 802 3af 802 3at E PoE Switch PoE PUANI PoE gt Im aay o CAT5e 6 ENGNG Power over UTP Lee LRP Injector LRP Extender Functions LRP 101UH LRP 101UE Power Input RJ45 with 802 3at af UTP with DC power over PU PoE input UTP input Power UTP with DC power over RJ45 with 802 3at af Output UTP output PoE output Installation Instructions Remove the Danger No Ethernet labels stuck on Step 1 jhe RJ45 LRP port of LRP 101UH and LRP 101UE Connect the LRP Injector LRP 101UH and LRP Step 2 Extender LRP 101UE to ends of RJ45 terminated long UTP twisted pair cable 1 Please do not connect any Ethernet equipment to LRP SU OUT Port o
13. P 101C KIT and LRP 101U KIT Solution 1 The LRP 101C KIT supports a maximum distance of 1km 2 The LRP 101U KIT supports a maximum distance of 500m May know which power source that can be accepted by LRP 101C KIT and LRP 101U KIT Solution 1 DC 56V power adapter 2 DC 48V power adapter 3 IEEE 802 3at High Power over Ethernet Switch 4 IEEE 802 3af Power over Ethernet Switch The LRP 101C KIT and LRP 101U KIT Performance is bad Solution The actual data rate will vary on the quality of the coaxial UTP cable and environment factors APPENDIX A NETWORKING CONNECTION A 1 Switch s RJ45 Pin Assignments 10 100Mbps 10 100BASE TX RJ45 Connector pin assignment MDI Media MDI X Media Contact Dependent Dependent PoE Interface Interface Cross 1 Tx transmit Rx receive Positive VCC 2 Tx transmit Rx receive Positive VCC 3 Rx receive Tx transmit Negative VCC 4 5 Not used Not used 6 Rx receive Tx transmit Negative VCC 7 8 Not used Not used A 2 RJ45 Cable Pin Assignments The standard RJ45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable Crossover Cable 12345678 Paral 12345678 SIDE 1 1 White Orange 2 Orange 3 White Green 4 Blue 5
14. P Extender LRP 101UE Long Reach PoE Extender UTP Figure 2 7 LRP 101UE Front Panel PoE our g the 10 100BASE TX 2 4 3 LRP 101UE LED Indicators Figure 2 8 LRP 101UE Rear Panel gt System LED Color Function PWR Green Lit indicates the power is on LED Color LNK Green gt LRP UTP Interface Function Lit indicates that the LRP UTP link is established Off indicates that the LRP UTP link is down gt RJ45 10 100BASE TX Interface LED Color Function PoE in Use Amber Lit indicates the RJ45 Port is providing PoE power LNK ACT Green Blink indicates the extender is actively sending or receiving data over that port 235 3 INSTALLATION This section describes the functionalities of the Long Reach PoE over Coaxial UTP Extender Kit s components and guides you to how to install it on the desktop Basic knowledge of networking is expected Please read this chapter completely before continuing 3 1 Installation Precautions of LRP 101C KIT As the LRP 101CH is power over coaxial injector it only can work with PLANET power over coaxial extender the LRP 101CE Please confirm that other non PoE equipment is not connected with the coaxial cable When you connect the coaxial cable with coax LAN converter CCTV camera etc it might cause other equipment to damage The package contains one Warning Sticker which should be stuck on
15. PoE extender solution eliminates the need for additional remote site power while allowing a single PoE source such as a PoE network switch to provide power to both LRP Extenders and the camera at long range This feature eliminates the need for local and remote site power supplies PoE IP Cam 7 P LRP 101CE Extender LRP 101CH Injector Bm Coaxial Cable Up to 1000m Stable Operating Performance under Difficult Environments PLANET Long Reach PoE Extender is the perfect solution for extended distance data and power transmission for warehouses parking lots campuses casinos and many more They can operate stably under temperature range from 20 to 70 degrees C which enables the users to conveniently apply the device in almost any location of the network 1 3 Product Features Power over Ethernet e Eliminates Power cabling with POE over Coaxial Supports Power over Ethernet PSE PoE Injector Power and Ethernet data transmission over coaxial up to 1km Power and Ethernet data transmission over UTP up to 500m Complies with IEEE 802 3af IEEE 802 3at Power over Ethernet PD on RJ45 port Supports Long Reach PoE power up to 30 8 watts Vary on power source and cable distance Supports PoE Power up to 25 watts Vary on power source and cable distance Auto detect remote powered device PD e Plug and Play no PC required Industrial Case Installation Supports ex
16. RP 101CH with 48 56V power adapter and one LRP 101CE with PoE power output The LRP Injector is powered via the external power adapter The IEEE 802 3at af compliant PoE PD will automatically be powered by the LRP Extender via UTP 110 240V AC AC to DC Adapter 60W 48 56V DC IN LRP 101CE E124 4 09 53 802 3af 802 3at PoE rM CAT5e 6 PoE IP Camera PLANET T EE cal LRP 101CH Power over Coaxial Long Reach PoE Injector j CAT5e 6 Ethernet Switch JN Ue Functions LRP Injector LRP Extender LRP 101CH LRP 101CE Power Input Power adapter with 48 56V DC in BNC with DC power over coaxial input Power Output BNC with DC power over coaxial output RJ45 with 802 3at af PoE output Installation Instructions Connect the LRP Injector LRP 101CH and LRP Extender LRP 101CE to ends of BNC terminated coaxial cable Stick the Warning Sticker on the coaxial cable Step 1 Connect Cat5 6 UTP cable to LRP 101CH and non PoE Sep 2 switch or workstation Connect 48 56V DC power adapter to LRP 101CH power socket then the PWR LED of LRP 101CH and LRP 101CE should lit up immediately Step 3 Connect Cat5 6 UTP cable to LRP 101CE and IEEE Step 4 802 3at af complied PoE IP camera or PoE Wireless AP 27 1 1 Before installation please consider the distance and watts value demand for PD devices The LR
17. ear Panel Figure 2 1 and Figure 2 2 show the front and rear panels of the LRP 101CH Long Reach PoE over Coaxial Injector LRP 101CH OUT Long Reach PoE 48 56V DCIN LNK ACAUTION e PWR 10 100BASE TX Injector Coax Figure 2 1 LRP 101CH Front Panel Figure 2 2 LRP 101CH Rear Panel 2 1 3 LRP 101CH LED Indicators System LED Color Function Power ON PoE PoE power input from RJ45 Lit PoE PD port PWR Green Power ON 48 56V DC power input from DC jack Off Power Off LRP Coaxial Interface LED Color Function LNK Lit indicates that the coaxial link is established Green Off indicates that the coaxial link is down gt RJ45 10 100BASE TX Interface LED Color Function PoE IN Amber Lit indicates the RJ45 port is receiving the PoE Power LNK ACT Blink indicates the extender is actively sending or Green receiving data over that port 17K 2 2 LRP 101CE 2 2 1 LRP 101CE Physical Dimensions LRP 101CE dimensions W x D x H 94 x 70 3 x 26 2 mm Rear Panel 68 5 PoElnuse LNK ACT 25 3 10 100BASETX Top Panel 70 3 Bottom 94 u E El a 5 gt 8 5 Ei bi YA 20 E S S PLANE LRP 101CE wei 5 O PWR 26 2 Long Reach PoE Extender Coax Front Panel
18. f 48 56V DC W DC Input 48 56V DC Power over RJ45 Input 44 56V DC Standards Conformance Standards Compliance IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3af Power over Ethernet 802 3at Type 1 IEEE 802 3at Power over Ethernet 802 3at Type 2 Regulation Compliance FCC Part 15 Class A CE Environment Operating 20 70 degrees C temperature Storage 40 75 degrees C mmm 2 Humidity Operating 5 95 non condensing Storage 5 95 non condensing 1 Upload LRP 101UE to LRP 101UH Download LRP 101UH to LRP 101UE 2 As there are various resistance values in the category 5 5e cable the actual data rate will vary on the quality of the copper wire and environment factors Depending on what the DC PoE Power Input and the length of UTP cable are 2 HARDWARE DESCRIPTION 2 1 LRP 101CH 2 1 1 LRP 101CH Physical Dimensions LRP 101CH dimensions W x D x H 94 x 70 3 x 26 2 mm Rear Panel 68 5 PoE IN LNK ACT 48 56V DCIN m m 0 iD QJ eco 10 100BASETX Top Panel 70 3 Bottom T REE ssi Y Y i RS Fr 1 5 I xi 5 Ai id p cJ ad i E I g I I eb I c 5 S i I gt i MS he E J LRP 101CH ha QJ D a A CAUTION Long Reach PoE Injector Front Panel 2 1 2 LRP 101CH Front Panel and R
19. f the LRP 101UH otherwise it will damage the Ethernet equipment 2 Please do not connect any Ethernet equipment to LRP Warning IN Port of the LRP 101UE otherwise it will damage the Ethernet equipment Connect Cat5 6 UTP cable to LRP 101UH and IEEE 802 3at compliant PoE Switch or PoE Injector If the PoE Step 3 switch or PoE injector is powered on already then the PWR LED of LRP 101UH and LRP 101UE should lit up accordingly Connect Cat5 6 UTP cable to LRP 101UE and IEEE oe 802 3at af complied PoE IP camera or PoE Wireless AP pes optimal power injection The other non standard PoE Ya The LRP 101UH accepts IEEE 802 3at equipment for Power devices may cause the LRP 101UH to malfunction Warning 1 Before installation please consider the distance and watts value demand for PD devices The LRP 101U KIT PoE powers output capacity and upload download performance depending on the length of UTP cable 2 As there are various resistance values in the cate gory 5 5e cable the actual data rate will vary on the quality of the copper wire and environmental factors 29 41 Type 2 LRP 101UH with 48 56V power adapter and LRP 101UE with PoE power output 110 240V AC AC to DC Adapter 60W 48 56V DC IN LRP 101UE ieee cu 802 3af 802 3at Ethernet Switch Bone 7 77 d Power over UTP LRP Injector LRP Extender Functions LRP
20. h PoE over UTP Injector LRP 101UH LRP OUT 48 56V DCIN NCAUTION Injector oco 10 100BASE TX Long Reach PoE Injector UTP Figure 2 5 LRP 101UH Front Panel Figure 2 6 LRP 101UH Rear Panel 2 3 3 LRP 101UH LED Indicators gt System LED Color Function Power ON PoE PoE power input from RJ45 Lit PoE PD port PWR Green Power ON 48 56V DC power input from DC jack Off Power Off gt LRP UTP Interface LED Color Function Lit indicates that the UTP link is established Off indicates that the UTP link is down LNK Green gt RJ45 10 100BASE TX Interface LED Color Function PoE IN Amber Lit indicates the RJ45 port is receiving the PoE Power LNK Gian Blink indicates the extender is actively sending or ACT receiving data over that port 21 _ 2 4 LRP 101UE 2 4 4 LRP 101UE Physical Dimensions LRP 101UE dimensions W x D x H 94 x 70 3 x 26 2 mm Rear Panel 68 5 PoE In use LNK ACT 3 Te QJ 10 100BASE TX Top Panel Le 70 3 T UJ E V EB 5 8 x 5 2 ar B J B E LRP 101UE IRPIN a INK QJ a Long Reach PoE Extender UTP Bottom Front Panel 2 4 2 LRP 101UE Front Panel and Rear Panel Figure 2 7 and Figure 2 8 show the front and rear panels of LRP 101UE Long Reach PoE over UT
21. limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human K health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET Long Reach PoE over Coaxial UTP Extender Kit User s Manual MODELS LRP 101C KIT LRP 101U KIT REVISION 1 0 January 2015 Part No EM LRP 101x KIT v1 0 2350 AN0100 000 TABLE OF CONTENTS I geleitet 6 1 1 Package Contentls 2 6 ette a cna Need esed 6 1 2 Intr
22. oduction of Long Reach Power over Ethernet 8 1 3 Product Feattres irit rn eto ori eph teg ER Sensi e addis 9 1 4 Product Specifications 3 559 aaae rea Pee 10 1 4 1 LRP 101C KIT Specifications eee 10 1 4 2 LRP 101U KIT SpecificationNS lt s semanananamananaa 13 HARDWARE DESCRIPTION wi 16 PNE ino 16 2 1 1 LRP 101CH Physical Dimensions eese 16 2 1 2 LRP 101CH Front Panel and Rear Panel 17 2 1 3 ERP 101CH LED Indicators eie tti eene nne dr Roue 17 2 2 il neu 18 2 2 1 LRP 101CE Physical Dimensions eese 18 2 2 2 LRP 101CE Front Panel and Rear Panel 19 2 2 3 ERP TOTCE LED Indicators erue ceceo eo oco ere terae 19 2 3 ERP 1TOTUPL ii 20 2 3 1 LRP 101UH Physical Dimensions eese 20 2 3 2 LRP 101UH Front Panel and Rear Panel 21 2 3 3 LRP 101UH LED Indicators 5 5 rire eani 21 2 Ba ama UA AUA UU USA 22 2 4 1 LRP 101UE Physical Dimensions eese 22 2 4 2 LRP 101UE Front Panel and Rear Panel 23 2 4 3 ERP 101UE LED Indicators icc eiecerunt nenas 23 3 INSTALLATION cesare eint entrant h neun res nena cue E da EAD DK Res 24 3 1 Installation Precautions of LRP 101C KIT esee 24 3 2 Installation Precautions of LRP 101U KIT eeeeeee 24 3 3 POWSF DDLUIOFIS ai 25 3
23. tensive LED indicators for network diagnostics Metal case protection Compact size DIN rail and wall mount design Supports 2000V DC EFT surge protection for power line Supports 2000V DC Ethernet ESD protection 20 to 70 degrees C operating temperature 9 1 1 4 Product Specifications 1 4 1 LRP 101C KIT Specifications Model LRP 101CH LRP 101CE Functions Long Reach PoE Injector Long Reach PoE Extender Hardware Specifications Copper 10 100BASE TX RJ45 Auto negotiation Auto MDI MDI X Power over Ethernet Standard IEEE 802 3at af PoE PD Powered Device IEEE 802 3at af PoE PSE Power Source Equipment PoE Input Supports both Mid Span and End Span PSE Input Range 48 56V DC Ethernet PoE Output 48 56V DC 600mA max sizes Interface PoE Budget Up to 25 watts End span RJ45 Pin PoE Mode 1 2 3 6 Data Rate 100 100Mbps Cabling Cat5e or above eal 100 meters Distance Maximum Frame 1522bytes Long Reach PoE Interface Connectivity 1 x BNC female connector Long Reach PoE over coaxial PSE Power Source Equipment 1 x BNC female Long Reach PoE over coaxial PD Powered Device Long Reach PoE Interface Power Input 37 56V DC Power Output 41 56V DC m BNC center pole m BNC center pole feet DC DC 9 m BNC shield
24. the coaxial cable connector before using PLANET Long Reach PoE over Coaxial Extender Kit A Caution ie Bis 3 2 Installation Precautions of LRP 101U KIT The package contains one Warning Sticker and it is stuck on the PoE IN LRP OUT RJ45 connector of PLANET Long Reach PoE over UTP Extender Kit As the LRP 101UH is power over UTP it only can work with PLANET LRP 101UE If connected with standard Ethernet equipment it might cause damage to the equipment 3 3 Power options m LRP Injector There are two ways to power the LRP Injector LRP 101CH and LRP 101UH Powered via PoE Powered via DC adapter m LRP Extender The LRP Extender must be powered by the LRP Injector or LRP Switch LRP 101CE must be powered by the LRP 101CH or LRP CS series switch over coaxial cable LRP 101UE must be powered by the LRP 101UH or LRP US series Switch over UTP Twisted pair cable A Please don t connect the LRP Extender to any PoE PSE Power Sourcing Equipment Caution 3 4 Applications of LRP 101C KIT with coaxial cable Type 1 One LRP 101CH with PoE power input and one LRP 101CE with PoE power output The LRP Injector is powered via IEEE 802 3at af PoE An IEEE 802 3at af compliant PoE PD will automatically be powered by the LRP Extender via UTP LRP 101CE Ie qmd 802 3af 802 3at PoE e mio CAT5e 6 PoE IP Camera 802 3af 802 3at PoE Switch PoE CAT5e 6 25 1
25. valuation regarding the EMC the following standards were applied EN55022 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2008 EN55024 2010 IEC 61000 4 2 2008 IEC 61000 4 3 2006 A1 2007 A2 2010 IEC 61000 4 4 2012 IEC 61000 4 5 2005 IEC 61000 4 6 2008 IEC 61000 4 8 2009 IEC 61000 4 11 2004 Responsible for marking this declaration if the Xx Manufacturer O Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 10F No 96 Minquan Rd Xindian Dist New Taipei City 231 Taiwan R O C Person responsible for making this declaration Name Surname Kent Kang Position Title Product Manager Taiwan 31 March 2015 Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw http www planet com tw 10F No 96 Minquan Rd Xindian Dist New Taipei City Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528
Download Pdf Manuals
Related Search