Home

STD Owners Manual complete - Power

1. Section 4 Installing the Lines and Cylinder Unpack the hydraulic cylinder from the box with the two 90 nickel plated push fit hydraulic line connectors pre installed Insert the 1 2 long bushing into the 5 16 hole in the RED end cap found in the Power Pole hardware bag Install on the same side as the hydraulic fit tings See fig 9b _ Partially remove the 1 4 x 3 1 2 bolt on the top of the stern bracket and install the cylinder The hydraulic fittings should be on the same side of the Power Pole as the serial plate Attach the hydraulic lines to the push fit connectors by simply pushing the line into the fitting no tools re quired Route the top line down the cylinder and se cure with the enclosed marine wire straps Route the bottom line directly down and thru the serial plate Fig 9b Continue to route each line behind the Serial plate and into the boat See fig 9a The lines can either go through or over the transom whichever you prefer Two through hull sleeves are included to make a clean transom penetration Cover the ends of the tubing with tape during the installation to prevent any debris from getting in the lines and contaminating the oil The slightest piece for dirt could cause severe problems Note With the Power Pole in the full up position pull any slack from inside the u channel this will prevent the hydraulic lines from jamming when lowing the Power Pole 11 IN
2. 14 IMPORTANT REGISTER YOUR POWER POLE Shallow Water Anchor This warranty registration card must be completed and mailed to JL Marine Systems Inc to validate your warranty CUSTOMER INFORMATION Purchaser s Name Age Purchaser s Address City State Zip Boat type Length E mail POWER POLE INFORMATION Date of Purchase Month Day Year Serial No Found on Stern Bracket Place of purchase CUSTOMER SATISFACTION Where did you hear about Power Pole What type of fishing do you prefer O Television show O Redfish Snook and Trout O Word of Mouth O Bone Fish O Internet O Tarpon O Advertisement type O Bass O Other O Other What is your favorite feature What is your favorite bait O Quiet O Live Bait O Convenience O Cut Bail O Boat Control O Artificial O Holding Power O Fly O Other 15 osu sod Jadoid ynoyyIM J AI 9D Jou II DIJO 750d 3H dwers SSE O SAILH Eld 6LOEE 14 VWAINVL EOe 3ALINS e XJA NIVd 8O0Z6 INI SWALSAS ANIAVIW WP YOHINY HILM MU IIHS w MWa dami Dd 16
3. in the manual describes the proper procedures for safely installing operating and maintaining your Power Pole CAUTION Do not use the Power Pole as your primary anchorage Never leave your boat unattended while an chored with the Power Pole TRAINING Read this operator s manual carefully Become familiar with the controls and know how to operate your Power Pole prop erly Do not allow children to operate the Power Pole without adult supervision Do not modify the unit in any way or add accessories not intended for this unit Always disconnect power from Power Pole before servicing PREPARATON Always make sure the Power Pole is in the full up position with a travel strap in place when on the trailer If any debris gets caught around the Power Pole DISCONNECT power from motor and remove any debris OPERATION In the event of pump failure the Power Pole may be manually raised by applying enough pressure to bypass the Pole Protector valve thus allowing the unit to come all the way up to the stowed position If the Power Pole is beyond reach it can be forced up by driving the boat to shallower water Depressing the up button on the Power Pole control may offer assistance Be sure to have the Power Pole in the full up position when using outboard motor at high speeds e Keep your hands and clothing completely clear of the Power Pole at all times e Do not use the Power Po
4. CHANTABILITY MADE WITH RESPECT TO SUCH ANCHORS JL Marine Systems Inc IS NOT LIABLE FOR ANY INJURY OR MISHAPS SUS TAINED IN THE USE OF THIS PRODUCT THE USER OF THIS PRODUCT AC KNOWLEDGES ASSUMED RISKS AND WAITVES ANY AND ALL CLAIMS AGAINST JL Marine Systems Inc AND ANY OF IT S AGENTS 7 N 7 N 7 N 7 N 7 N 7 N 7 N This warranty applies under conditions of normal use The warranty does not cover 1 defects caused by improper assembly or disassembly 2 defects occurring after purchase due to product modification intentional damage accident misuse abuse negligence or exposure to corrosive elements 3 cosmetic damage and 4 labor or assembly costs 7 N Except as provided herein JL Marine Systems Inc makes no express warranties and any implied warranty including without limitation any implied warranty of merchantability or fitness for a particular pupas is limited in its duration to the duration of the written limited warranty set forth herein f N Except as provided herein JL Marine Systems Inc shall have no liability or responsibility to the purchaser or any other person or entity with respect to any liability loss or damage caused or alleged to be caused directly or indirectly by use of the product including but not limited to any incidental or consequential damages Some states do not allow limitation on how long an implied warranty lasts or the exclusion of limitation of incidental or consequent
5. STALLATION IMPORTANT Once the lines are routed behind the serial plate and connected to the push fit connectors move the cylinder through the entire range of motion to make sure the lines are not going to kink chafe or otherwise be damaged during normal use Install the Pole Protector valve as indicated in fig 10 then route the lines from the Power Pole to the HPU through the most con venient and direct way Attach with clips and hose benders wher ever necessary COVER THE ENDS OF THE TUBING TO PRE VENT CONTAMINATION FROM ENTERING THE SYSTEM WHILE ROUTING THE LINES THROUGH THE BOAT Make sure the line that has the Pole Protector in it is attached to the base side of the hydraulic cylinder See fig 10 Hydraulic SEN Power Unit Protector Ox 0O v cS s gt O Fig 10 INSTALLATION Section 5 Choose Location for Switch The control switch should be mounted where it is easily accessible from anywhere on the boat Remember the switch requires a 12v DC supply with a minimum of 12 AWG wire If the switch is mounted in the bow of the boat you should use 10 AWG wire Multiple switches can also be installed Section 6 Mounting Switch Mark the cutout area and allow room for the faceplate screws Check to make sure you are not going to interfere with anything on the other side Use a jig saw to cut out the marked area then screw in place Section 7 Connect Wires IMPORTANT The 12v source should
6. azu i lt Tai OWNER S MANUAL INSTALLATION OPERATION MAINTENANCE STANDARD PUMP SYSTEM Powered By Bennett Hydraulics CAUTION Read this instruction manual carefully Become familiar with the controls and know how to operate the Power Pole system safely US Pat No 6 041 730 amv WN A WN av aN A 7 aN SN NEL NEL N A FIVE 5 YEAR LIMITED WARRANTY KEEP YOUR RECEIPT ORIGINAL PURCHASE Any Power Pole manufactured by JL Marine systems Inc is warranted against defects in material and workmanship in the stern bracket U channel Knuckle joint hydraulic system and electrical system according to the following stipulations 7 N 7 N The Power Pole is warranted to the original owner for a period of five years from the date of purchase A A Power Pole component which proves defective within ninety oY days from date of purchase will be repaired or replaced at JL Marine Systems Inc option free of charge to the owner JL Marine Systems Inc will pay for the replacement product shipping and handling fees to and from the JL Marine Systems Inc s wee plant or some other place which JL Marine Systems Inc might esignate 7 N 7 N A Power Pole component which proves defective after twelve 12 months but before sixty 60 months will also be repaired or replaced free of charge but there may be a shipping and handling charge to and from the JL Marine systems Inc manufa
7. be directly from the bat tery with a minimum size of 12 AWG wire If an inadequate wire is used the Power Pole may not function properly Fig 11 PUMP Remove this cutout from your man ual and tape to your console at the desired switch location Using a fi berglass cutting blade cut the solid line Try to remove all the line with out going outside the dashed line Switch Cutout Template Cut the line 13 INSTALLATION Section 9 Prime Pump After all lines are completely installed remove the plug from filler stack located at the front left corner of the reservoir Fill reservoir to Full Line using any type automatic transmission fluid ATF Using the control cycle the cylinder from all the way out to all the way in several times to clear all the air from the system No bleeding is neces sary To prevent the cylinder from scaring the inside of the u channel wrap the end of the ram with a soft cloth during this step Section 10 Final Assembly 1 Using the 5 16 x 3 5 bolt attach the cylinder ram to the U channel as shown Hardware list for this step Qty 1 5 16 x 18 x 3 5 bolt Qty 2 5 16 thin wall washer Qty 2 5 16 brown bushing Qty 1 5 16 low profile lock nut Qty 1 small ram spacer Qty 1 large ram spacer 7MOOW gt NOTE The large spacer goes on the same side of the ram as the hydraulic fittings to offset the cylinder enough so that the lines do not interfere with the u channel
8. cturing plant or some other place which JL Marine Systems Inc mihi s In the case of replacement parts of same or equivalent model will be used 7 N 7 N This warranty covers the finish for a period of six 6 months from the date of pur chase not to crack chip or fade This warranty covers the hydraulic pump and cylinder for a period of 36 months Pump damage due to submersion or excessive exposure to water may void this warranty Power Pole warranties are activated upon rca by JL Marine Systems Inc of the completed warranty card postdated within 10 days of purchase Please retain our sales receipt as Boo of purchase I his warranty is void if the Power Pole is used commercially structurally altered or subject to stress beyond the physical limits of the anchor material This warranty does not cover abrasion or abnormal abuse nor does it cover an an chor while being used for anything other than what it was intended for JL Marine Systems Inc reserves the right to change products and designs without incurring any obligations to incorporate such changes in already completed products or those in the hands of dealers or consumers Anchors repaired or replaced under this warranty may or may not have these changes THE WARRANTY CONTAINED HEREIN IS THE EXCLUSIVE WARRANTY MADE BY JL Marine Systems Inc AND THERE ARE NO OTHER WARRANTIES EX PRESSED OR IMPLIED INCLUDING A WARRANTY OF FITNESS FOR A PAR TICULAR PURPOSE OR OF MER
9. ial damages so the above limitation and exclusion may not apply to you N N This warranty gives you specific legal rights You may also have other rights which vary from state to state A JEN JEN LON W I W I I I Mf I I I I I I I p ALAN LAN LPN LPN PON PN a a a a PrN 4 Warranty Procedure a To obtain warranty service take or ship your Power Pole to JL Marine Systems Inc or to a JL Marine Systems Inc author ized service station together with a note describing your com plaint and your copy of the dated purchase receipt If you choose to ship your Power Pole to JL Marine or an author ized service station all shipping arrangements must be made by you and all shipping charges and insurance must be fully pre paid All to and from shipping charges for JL Marine systems Inc products which have been serviced under this Warranty within ninety 90 days of the purchase date may be reimbursed by JL Marine Keep this information for your records Model Serial No Customer s Name Place of purchase Date of Purchase aN JL MARINE SYSTEMS INC 9208 PALM RIVER ROAD SUITE 303 TAMPA FL 33619 813 689 9932 CONGRATULATIONS on your purchase of a Power Pole Shallow Wa ter Anchor system It has been designed engineered and manufactured to give you the best possible dependability and performance for years of enjoyment Please read and retain this manual The information contained
10. l Bits 12 1 Quart Automatic Transmission Fluid 13 1 amp 2 Phillips Head Screw Drivers 14 Jig Saw or Rotary Saw Ce ee ae Hardware Included Qty 4 5 16 x 3 5 all thread transom mount bolts Qty 1 5 16 x 3 5 cylinder ram bolt Qty 2 cylinder ram spacers Qty 2 thru hull bushings Qty 1 Cylinder end cap bushing Qty 3 marine wire ties Qty 4 5 16 fender washers Qty 4 5 16 lock nuts Qty 4 neo bond washers Qty 2 cylinder ram bolt wash ers Qty 2 Brown cylinder ram bolt bushings Qty 1 5 16 low profile locknut Pole Protector valve INSTALLATION Hydraulic Power Unit Included HYDRAULIC 1 POWER UNIT HPU Fig 1 VP1135 G Green 4 1 8 NPT to 1 4 tube connector To VP1146 cylinder base 5 1 8 NPT to 1 4 tube connector To VP1146 cylinder end mas osa yma esas me 6 INSTALLATION Parts Included Fig 2 mmm Top Arm Inside PP1015 12 Hydraulic Cylinder HL12CDA Serial Number keeper plate PP1018 n ucuman SS INSTALLATION Mechanical Schematic HPU F JLDLI2DA Preset at Hydraulic Power Unit 550 PS Fole Protector Hydraulic finder Dash Switch Fig 3 INSTALLATION Section 1 Choosing the Location IMPORTANT Carefully consider and physically check all 5 steps in section one before mounting the stern bracket 1 Left or Right side of the Boat P
11. le as a step or handle to enter or exit the boat Never allow children to play with or around the Power Pole The Power PoleTM is fully powered never give any assistance to raise or lower e In high wind or rough seas the Power Pole may relieve holding pressure to protect your boats transom Never leave your boat unattended while your Power Pole is providing anchorage MAINTENANCE AND STORAGE CAUTION Hydraulic lines always have pressure disconnecting the lines will cause sudden high pressure leakage and Power Pole failure which may cause bodily harm Check all hydraulic lines at frequent intervals for proper tightness to be sure there are no leaks Make sure all power connections are secure and free of corrosion Check all nuts bolts and screws at frequent intervals for proper tightness to be sure Power Pole is in safe working condi tion Check all hydraulic lines at frequent intervals for possible chaffing or damage from kinking or abrasion Keep the hydraulic reservoir filled within the indicator marks at all times Thoroughly rinse and lubricate all moving parts after each use a gt 92 th o INSTALLATION Tools and Materials Needed 7 16 1 2 amp 9 16 Wrench 7 16 1 2 amp 9 16 Socket and Ratchet Electric Drill Four Foot Straight Edge Marine Grade Sealant Tape Measure Wire Cutters Razor Tube Cutter Small Funnel 10 Wire Crimpers 11 5 16 amp 5 32 Dril
12. osition in Wind boat Right handed caster should put the Power Pole on the right side and left handers should be on the left side This is especially important when fly fishing The boat will pivot in the wind to the proper angle for easy downwind casts without Boat doesn t interfere the back cast being over the center of the with back cast for right boat handed caster 2 Vertical Positioning no trim tabs Use a straight edge on the bottom plane of the boat directly below and centered from the Stern Bracket Mount the Power Pole so that the Bottom Arm mounting point of the stern bracket is 4 above the straight edge 3 Trim Tab Clearance If your boat has trim tabs it is very impor tant to check their clearance requirements before mounting the bracket For exam ple when the bracket is mounted at the suggested 4 above the bottom plane of the boat it will have about 11 5 of clear ance for trim tabs If your Trim Tabs are 12 and you are mounting the bracket over them then you must mount it at least 5 above the boat s bottom plane rather than the suggested 4 Standard 9 Trim Tabs do not interfere with the Power Pole 9 INSTALLATION 4 Obstructions Look inside the boat along the transom to make sure that the bolts will not have any obstructions 5 Motor Clearance oe 3 Minimum ok Turn the motor all the way in the clearance direction of the Power Pole then lower
13. to make sure the motor does not interfere Spin the propeller to make sure it has clearance also Allow a minimum of 3 between the motor and the Power Pole at all times in any position See fig 7 Section 2 Mounting The Stern Bracket Hardware list for this step A Qty 4 5 16 x 3 5 all thread bolts B Qty 4 5 16 Neo bond rubber backed washers C Qty 4 5 16 fender washers D Qty 4 5 16 locknuts Once a location has been chosen mark all four holes Before drilling any holes double check the inside to be sure that the bolts are not going to interfere with anything and that you have plenty of room to tighten the nut on the other side Once all four holes are marked and drilled fasten the Stern Bracket using the listed hardware The rubber backed washers are to protect the powder coated surface of the stern bracket Use a marine quality sealant on and around the bolt and holes then tighten adequately DO NOT OVER TIGHTEN 10 INSTALLATION Section 3 Hydraulic Power Unit HPU Install the HPU In a convenient location and in a dry environment Important The HPU must be mounted in a dry enough location to avoid submersion and drenching Allow space above the HPU so that it may be slid into its mounting bracket about 3 Layout upper holes on HPU mounting bracket 4 5 8 apart and start 10 x 1 screws using 5 32 pilot holes Then drill 5 32 pilot holes for lower screws and mount bracket Slide HPU into bracket

STD Owners Manual complete - Power

Contents

Download Pdf Manuals

Related Search

Related Contents