Aristel AN4004 GSM FIXED WIRELESS
Contents
1. Aristel AN4004 GSM FIXED WIRELESS TERMINAL MANUAL V3 1 This manual contains important information Please read before using the equipment B 5 6 4 1 4 2 4 3 4 4 4 6 Contents Function Descriptions e Eae Eu e e e eee EE 4 Operation Guide 4 Power NO EO red pg tlc qa bled eat dd Mnt 4 Panel indicator LED status uos vct o Ere Toe eet 5 Make iCall eco arent eng qucd a En Toc a Pvt o 5 qal soo deter aca 5 Parameter Se IP ouis iie errato eese epo eiu 5 4 6 1 Command Ile sucre erm de teta 6 4 6 2 Factory default setting ere octo 6 Configuration and installation 8 ls nV 9 1 Introduction Congratulations on choosing an Aristel GSM Fixed Wireless Terminal Your Aristel Fixed Wireless Terminal FWT is designed to work on GSM networks It can be connected to single line telephones SLT or PABX systems using analogue SLT ports It is supplied with rack mounting brackets 2 Warning Please observe the following 1 Avoid using this product in petrol stations bunkers and places of chemical storage 2 Avoid using this device in areas where wireless transmission equipment is restricted such as hospitals health care facilities and on board aircraft 3 Use only 2 wire line cords supplied when connecting to SLTs and PABX systems 4 The voice quality may vary between networks 5 As of March 2009 the fol2. lowing networks will work with this device Telstra GSM 900 1800 Optus 900 1800 Vodafone 900 1800 Telstra Next G SIM cards will default to GSM 900 1800 Telstra network Installers should check GSM site reception using a GSM handset or a 3G handset set to GSM only This is important for country areas Hutchison 3 will not work with this FWT It is a 3g only network 6 The equipment should be installed and maintained by a qualified personal 7 Position the antennae in a location where signal strength is not impaired 3 Function Description This FWT has the following 1 Standard RJ11 phone socket interface 2 Caller ID with DTMF 3 This FWT has the flexibility to bar call destinations such as 1900 calls national long distance calls international calls mobile calls or local phone calls 4 Supports locking SIM card locking network locking district functions 5 Supports traditional PBX access and reversal on idle 6 Dialing control Ability to set up several special phone numbers restricted numbers 7 Realtime displaying of wireless network signal strength 4 Operation Guide 4 1 Power On Turn on the power switch The equipment will initialize itself and search the network This will take about 20 seconds During this process the running indicator LED keeps flashing After this process is finished the equipment is ready and the signal indicator LED will be lit Dial tone can be heard if off hook If the e
3. ntact side down d Close the SIM card clamp and secure it Close the SIM card cover plate and replace the 8 screws Connect the antenna e into the socket s using the 2 wire line cord s provided connect the SLT or the PBX SLT port to FWT RJ11 socket Connected the power cord Turn on the main power switch and the relevant individual power switches at the back of the FWT The unit will be operational after the initialization period of up to 30 seconds 6 Technical Data 1 2 3 4 5 Antenna interface standard GSM900 1800 MHz or GSM 850 900 1800 1900 MHz as stated on the equipment case SIM card Support 3V 1 8 V adaptive G SIM card Phone interface DTMF line interface RJ 11 phone interface On hook voltage 45V Off hook current 30 41 Dialing tone frequency 450 Hz Antenna interface antenna gain 3 5 DB Sensitivity 104 DBM Antenna transmission power 3 W Impedance 50 ohm Working environment Operation temperature 20 60 Operation humidity 45 95 Storage temperature 20 60 Atmosphere pressure 86 106 Kpa Environment noise 60dB This device has a 12 months warranty from the date of purchase
4. quipment is locked or SIM locked or network locked the equipment checks itself And if the check inspection has failed the equipment will send out error tone for 2 minutes and release the connection 4 2 Panel indicator LED status Count from the left to the right 1 LED Off hook LED Off hook LED is on after pick up handset or press Handfree key 2 LED Speaking LED Speaking LED is on when the conversation start 3 44 5 LED Signal LED Indicate the strength of the signal 6 LED Power Indicator LED Power Indicator LED is on when switch on the power 4 3 Make a call When the signal LEDs are on and you hear dial tone after you pick up the handset or connect to the PBX trunk then you can make a call 4 4 Receive a call On an incoming call ring current is sent to the SLT or PBX device with Australian ring cadence 4 5 Parameter setting The parameters can be set by a telephone keypad Enter the setting mode by command 7788 exit from the setting mode by command KET 7 88H One long beep can be heard if successful Two short beeps can be heard if unsuccessful After completing the setting command hang up and then pickup the handset to set another command 4 5 1 Commands Table b da long distance y WIP 1 noo International long distance IP2 Nonlocal Mobile IP3 3 Ip3s Local calls barred 20 21 0 Incoming barred 21 1 22 0 Call National long di
5. stance 4x29 423504 Restriction Parred International long 23 4 x24 0 distance barred Local Mobile barred 25 0 Speaker Gain 30 x 1 4 Volume Adjusting Card Lock lock Manage Machine lock 43 0 Network lock EAA KOH Billing Meter 50 0 Other Hide local phone number 66 0 Commands Clear 0 for Nonlocal 51 0 Mobile Reset to Default value Any programming will come into effect only after power reset 4 5 2 Default setting of the factory Special code 6000 Local area code none IP1 none Mobile IP off Barr Incoming off Barr national long distance off Barr national long distance off Barr local call off Barr local handset off PIN 1234 Speaker Gain 3 Speaker volume 3 Microphone gain 3 Microphone volume 3 Card lock off Machine lock off 5 Configuration and installation 1 Packing List unit set Antennae 4 pieces User Manual volume Power cable piece 2 Installation Steps The equipment uses the GSM network s and requires an active SIM card s which are NOT pin locked Install the Fixed Wireless Terminal in a suitable place Turn off the main power switch at the back of the unit Install an active SIM card a Take off the 8 screws of the SIM card cover underneath the unit b Open the SIM card cover Move the SIM card clamp according to the amow c Liftthe SIM card clamp to insert the SIM card co
Download Pdf Manuals
Related Search