Home

Owner`s Manual (General)

1. This water dispenser is for indoor use only Room temperature should not exceed 97 F 36 C VE LU Y RIVYY 8 This water dispenser has two thermostats one for the cooling compartment and one for the cold water rear panel a For the cold water there is a 304 stainless steel water cooling tank All waterways are made from 304 stainless steel Refrigeration compressor is quiet and durable For the hot water there is a 304 stainless steel heavy duty hot water tank with an external heater It is suitable for mineral water The power cord has a grounded plug Please make sure that your outlet is properly grounded Easy to clean drain tray in the bottom of the cooling compartment Integrated No Spill Receptacle System for added hygiene and convenience Three power switches on the rear of the water dispenser One is for the hot water the second is for the cooling compartment and the third is for the cold water and cooling compartment The front panel has three indicator lights to see if the power heating and refrigeration are on There are three taps on the front The tap handles are color coded Red is for hot white for room temperature and blue for cooled water The hot water tap handle has a child resistant hot water guard To operate it squeeze the handle and locking device together and then push them down Easy to clean deep drip tray Convenient built in fast cooling compartment
2. PREPABIN s DU Be gt BU U 1 Make sure that the water dispenser is not plugged into the electrical outlet 2 Before placing water bottle on unit be sure that the drain plug on the back is tightly fastened 3 Hold the water bottle vertically and upside down over water dispenser and place the water bottle into the no spill bottle receptacle Apply slight pressure in order to pierce the bottle cap with the spigot It is not advisable to make any adjustments to the thermostat settings before the water dispenser and bottled water are warmed up to normal room temperature This unit accepts two three or five gallon water bottles with pierceable sealed caps 4 Open the taps to let the air out until the water starts to flow When this happens release the taps 5 Plug the water dispenser into a grounded power outlet and turn the power switches on 6 If the water dispenser is brought in from outside in the winter time give it a few hours to warm up to room temperature before plugging it in The thermostat setting may be affected by the coldness of the water dispenser itself or the bottled water e The refrigeration thermostat is factory set between 7 C and 8 C 44 6 F and 46 4 F e The hot water thermostat is factory set between 88 C and 89 C 190 4 F and 192 2 F PLACE e The hot and cold indicator lights will be on while the system is working Once the desired BOTTLE temperatures have been reached the lights will
3. load inside of the cooling compartment You may turn the cold water amp cooling compartment switch on once the cold water tank is thawed The cooling compartment temperature is controlled therefore the cooling compartment can t freeze If too many items are placed in the cooling compartment the water may freeze Turning the refrigeration thermostat counterclockwise to a warmer setting may reduce the probability of water freezing There are too En items in the cooling compartment or the items are too warm It is not advisable to place contents with a temperature exceeding 40 C 104 F in the cooling compartment The door of the cooling compartment is not closed Verify that the cold water switch is ON The cold water thermostat is set at high temperature position Turn cold water thermostat clockwise a little to set it at a lower temperature position The top portion of the tap has become loose If so tighten the top threaded portion A calcium deposit has formed in the p If so wash the inside of the water dispenser unscrew and clean the top portion of the tap and reassemble 10a The bottle may have small pinholes 10b The drain plug is not fastened properly Check that the soft rubber seal of the drain cap is not torn or damaged 10c The drain tray at the bottom of the cooling compartment is full of water Take out the drain tray to remove water and then place it back into the cooling compartment NO 0101 NO 010
4. the product Improper voltage or current Use contrary to the operating instructions Deviation from instructions regarding storage and transportation Disassembly Repair or alteration by anyone other than PHC EG or a PHC EG Authorized service center Further the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes PHC EG shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty Some states provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state or province to province HOW TO OBTAIN WARRANTY SERVICE You must contact PHC EG Customer Service Technical Support at our toll free number 1 877 383 6399 A Customer Service Technical Support representative will attempt to resolve warranty issues over the phone If telephone resolution is not possible the Customer Service Technical Support representative will require your assistance in performing routine diagnostic procedures This warranty is effective for the
5. 1 AC 115V 60 Hz 7A 4 5 Amperes Power supply Hot water heater power consumption Refrigeration compressor power consumption 2 5 Amperes Refrigerant type R 134a Refrigerant quantity 52 1 Gram 1 8302 Cold water cooling capability 2L 67 6 fl oz hour at room temp below 30 C 86 F cools down to 10 C 50 F Hot water heater capability 5L 169 1fl oz hour at room temp above 20 C 68 F heats up to 90 C 194 F Cooling compartment cooling temperature 0 C 10 C 32 F 50 F Volume of cooling compartment 0 64 cu ft 18 L Net weight 56 1 lbs 25 5 kgs Dimensions 15 25 LX 12 76 W X 38 H 38 7cm L X 32 8cm W X 96 5cm H Cook tap flow rate 2L 67 6 fl oz minute NOTE UL model number on the back of the unit refers to Sunbeam Water Dispenser with Cooling Compartment ELECTRICAL DIAGRAM Protection diode for the LED indicator light Cooling on LED indicator light Diode for the LED indicator light Resistor for the LED indicator light Cold water amp refrigeration power switch Refrigeration thermostat for the cold water PTC starter for the compressor Refrigeration Compressor Fridge power switch Refrigeration thermostat for the fridge Se AA eS p e AS Thermal protector for the refrigeration compressor Protection diode for the LED indicator light Heater on LED indicator light Diode for the LED indicator light Resis
6. 1 POSTAL CODE ZIP __ PHONE NUMBER 2 i COUNTRY SS I PURCHASED FROM STORE NAME E ADDRESS 1 CITY o STATE PROVINCE POSTAL CODE ZIP __ _ COUNTRY __ l b m m e ee eee ee dd TT Sunbeam is a registered trademark of Sunbeam Products Inc used under license DEPRECIATION Any unit being diagnosed as non functional and warranting an exchange during the existing warranty period will be subject to an appropriate depreciation or user fee ABOUT YOUR PRODUCT WARRANTY We welcome warranty repair and apologize to you for being inconvenienced Any Authorized service dealer may perform warranty repairs Most warranty repairs are handled routinely but sometimes requests for warranty service may not be appropriate For example warranty service would NOT apply if the product damage occurred because of misuse lack of routine maintenance shipping handling warehousing or improper installation Similarly the warranty is void if the manufacturing date or the serial number on the product has been removed or the equipment has been altered or modified During the warranty period the Authorized service dealer at its option will repair or refund any part that upon examination is found to be defective under normal use and service NORMAL WEAR This warranty does not cover normal wear of parts or damage resulting from any of the following Negligent use or misuse of
7. RANTIA AVERTISSEMENT Le distributeur d eau doit tre laiss en position verticale pendant au moins dix 10 heures sans tre branch Pendant la livraison et ou l entre posage le fluide l int rieur du compresseur se d placera Pour viter tout dommage l unit vous devez accorder le temps suffisant pour que le fluide se replace Assurez vous de remplir un verre de 12 oz d eau partir de chaque robinet avant de d brancher de l appareil ADVERTIR El distribuidor de agua debe permanecer desenchu fado y en posici n vertical al menos diez 10 horas Durante la entrega y o el almacenaje el l quido adentro del compressor se mover Hay que dejar 0 64 cu ft 18L cooling compartment un tiempo suficiente al liquido para que se asiente C ti HSE d t para evitar cualquier d no a la unidad ompartiment retroiaisseur a une Capacite Asegurarse de llenar un vaso de 12 oz de agua de de 0 64 pied cube 18L cada llave de enchufar la unidad Compartimiento fr o con capacidad para 0 64 cu ft 18L 2005 Sunbeam Products Inc All rights reserved Sunbeam is a registered trademark of Sunbeam Products Inc used under license Manufactured for Prestige Home Comfort a subsidiary of the Elite Group Inc Montreal Canada H3B 3X9 2005 Sunbeam Products Inc Tous droits r serv s Sunbeam est une marque d pos e de Sunbeam Products Inc utilis e en vertu d une Toll Free Tel T l sans frais Tel sin cargo au
8. WATER DISPENSER DISTRIBUTEUR D EAU DISTRIBUIDOR DE AGUA 5 USER MANUAL E MANUEL D UTILISATION E MODO DE EMPLEO M Cold hot and room temperature water M Includes cooling compartment E Child resistant hot water guard M Eau froide chaude et de temp rature ambiante i 1 E inclut un compartiment refroidisseur J M Poign e du robinet d eau chaude l preuve a des enfants M Agua fr a caliente y de temperatura ambiente M Incluye un compartimento fr o IMPORTANT AVIS AVISO Do Not Return this Product To The Store M Manubrio con golpecitos para agua caliente a prueba de ni os 1 877 383 6399 2 30am 5 30pm E S T DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE Ne pas retourner ce produit au magasin Veuillez appeler le service la diente pour toutes questions au 1 877 383 6399 an3o 17h30 H N E PREUVE D ACHAT ORIGINALE REQUISE POUR SERVICE DE GARANTIE WARNING Your water dispenser must be left upright for at least ten 10 hours unplugged During delivery and or storage the fluid inside the compressor will move To avoid any damage to the unit you must allow adequate time for the fluid to settle Make sure to fill one 12 oz glass of water from each tap before plugging in the unit ANNEES No devolver este producto en el almac n Porfavor llamar el servicio a la chentela 1 877 383 6399 a 30am 5 30pm E S TE PRESENTAR EL RECIBO ORIGINAL PARA EL SERVICIO DE GA
9. by unscrewing the base piercing pin Fig B Then proceed to wash it with dishwashing liquid rinse it and reassemble md Clean the inside of the water dispenser periodically with a small amount of vinegar This removes mineral scaling caused by the water Rinse it well Use the drain on the back in order to get the water out Make sure to open up all the taps to ensure that all cleaning liquid is drained from your water dispenser Put all of the parts back securely fasten the drain plug Fig C It is important to let the water dispenser dry for TWO HOURS before plugging it back in Cover the bottle receptacle to prevent it from contamination The harder the water you use the more often you should clean the interior of the unit Recommended intervals are between one and three months depending on the mineral content of the water and the frequency of bottle changes COOLING COMPARTMENT CLEANING INSTRUCTIONS 2 To clean the unit first unplug the power cord Allow the ice build up to melt naturally NOTE Do not use sharp objects or knives to remove ice buildup Do not use boiling water to remove ice UI The water will accumulate in the tray at the bottom of the compartment e Remove the tray from the compartment and empty the water Ul lt Wipe the compartment and the tray with a soft cloth dampened with liquid dishwashing soap TROUBLE SHOOTING GUIDE _________________ Prob
10. ce 6 SPECIAL 7 Electrical dia aaa 7 NOLES OECD Poo a nue 8 MN GIG e 9 10 FRAN AIS lectricit et s curit 11 D ballage de votre distributeur d eau 12 Caract ristiques de votre distributeur d eau 12 Pr paration de votre distributeur d eau des fins d utilisation 13 Fonctionnement de votre compartiment refroidisseur sssssesssseseeesen 13 Entretien du distributeur d eau 14 Directives en cas de probl mes 15 Sp cifications See ee eee eee eet 16 Sch ma lectrique 16 Garantie PE 17 18 ESPANOL Electricidad y seguridad o 20 Desembalar su distribuidor de agua 21 Caracteristicas de su distribuidor de agua 21 Prepare su distribuidor de agua antes de USING nes 22 Funcionamiento del compartimento fr o 22 Mantenimiento del distribuidor de agua 23 Qu hacer si tiene problemas 24 Especificaciones sses 25 Diagrama el ctrico nes 25 NOl Sa in R 26 Garant a dec ve cecaca avert cecens eeereetensciventers 27 28 ENGLISH ELECTRICAL SAFETY IIA When using electrical appliances basic safety precautions should be followed to reduce the risk of fire electric shock and injury to persons or property Read all instructions before using any appliance e Do not let hot water touch bare skin Keep combustible materials such as furniture bedding pillows clothes and or pa
11. cuenta 1 ao w D O El distribuidor de agua debe permanecer desenchufado y en posici n vertical al menos diez 10 horas Durante la entrega y o el almacenaje el l quido adentro del compressor se mover Hay que dejar un tiempo suficiente al l quido para que se asiente para evitar cualquier d no a la unidad Antes de colocar la botella de agua sobre la unidad aseg rese que el tap n de desag e en la parte posterior est bien apretado Deje un espacio de 10 cm como m nimo entre el aparato y la pared Deje un espacio libre de al menos 5 cm a cada lado del aparato Instale una botella de agua en el distribuidor Enchufe el distribuidor de agua Asegurarse de llenar un vaso de 12 oz de agua de cada llave de enchufar la unidad NOTA Enchufe la unidad Una vez que se haga esto ponga los interruptors situados detr s del aparato en posici n ON El agua caliente estar disponible en unos 15 minutos y la fr a en menos de una hora Para cualquier cuesti n observaci n o info rmaci n respecto al servicio marque el 1 877 383 6399 8 30 a m 5 30 p m E S T E TABLE OF CONTENTS OO TABLE DES MATIERES A ENGLISH Electrical Safety n o 2 Unpacking your water dispenser 3 Getting to know your water dispenser 3 Preparing your water dispenser for use 4 How your cooling compartment works 4 Water dispenser maintenance oc o 5 Trouble shooting guide c ce
12. d and the air is purged from the dispensing buttons NSEE NO 0101 ongratulations you have acquired a high quality SUNBEAM Water Dispenser for bottled water This unit is packed with C many extra features that you will find convenient to use Multi temperature capability allows you to enjoy a cool hot or room temperature drink It will provide you with many years of trouble free use by following the simple instructions contained in this manual Please take the time to read it carefully 1 Remove the water dispenser trom the cardboard 2 Wipe it clean if necessary box without turning it upside down or laying it age 3 Find a location for your water dispenser that is on its side protected from direct sunlight and other sources a Remove the strapping of heat Place the water dispenser on a level surface Make sure that there are at least BS EON mn o 4 10cm of space between the back of c Remove the styrofoam packing inserts from the box your water dispenser and the wall Keep a d Pull the water dispenser straight up from minimum distance of 2 5cm on each side sytrofoam base of your water dispenser free e Remove the plastic bag 4 Do not plug your water dispenser into the power outlet yet Read the instructions first The refrigeration compressor has very sensitive mounts inside of its welded shell in order to provide quiet running Improper handling may damage the compressor
13. go off a VERTICALLY e f you choose to set the cold water thermostat to the lowest setting it may take over one hour to cool the water down to the coldest setting STRAIGHT e Before the water dispenser leaves the factory the thermostat is set properly It is not advisable to DOWN adjust the thermostat when using the water dispenser for the first time NOTE When your water dispenser is in operation there is a small amount of water in the passage between the water tanks and the taps This water is not controlled by the cold hot or room temperature settings We recommend that in order to fully enjoy the desired temperature setting you should eliminate this small amount 200ml 400ml 6 76 fl oz 13 52 fl oz using a small glass container HOW YOUR LIN MPA RIVIENT WORK THE COOLING COMPARTMENT IS DESIGNED FOR EVEN COOLING Your water dispenser has two thermostats located at the back of the unit One thermostat controls the water and the other controls the cooling compartment To start the compressor a signal from either of the two thermostats is required Your water dispenser also has three power switches located at the back of the unit One switch controls the hot water one switch controls the cooling compartment and the other switch controls the cold water and cooling compartment Both the cold water thermostat and the cooling compartment thermostat are factory set between 2 and 4 To adjust the temperature of the
14. ill be free from defects in material for a period of one 1 year and a period of ninety 90 days on labor PHC EG at its option will repair or refund this product found to be defective during the warranty period If the product is no longer available PHC EG may refund your purchase at a depreciated value with an original proof of purchase This is your exclusive warranty CONDITIONS ORIGINAL SALES RECEIPT This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty service and or refund PHC EG dealers service centers or retail stores selling PHC EG products do not have the right to alter modify or in any way change the terms and conditions of this warranty WARRANTY REGISTRATION IS NOT NECESSARY TO OBTAIN WARRANTY ON PHC EG PRODUCTS SAVE YOUR PROOF OF PURCHASE RECEIPT IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY Continued on Next Page pr ee nn o ee ee ee ee ae l I WARRANTY CONTROL CENTER PLEASE PRINT LEGIBLY i SERIAL amp MODEL NUMBER INFORMATION CAN BE FOUND ON SILVER UL LABEL I PURCHASE DATE DAY MONTH YEAR SERIAL NUMBER ____ MODEL NUMBER _ o I l l CUSTOMER NAME _ _ I ADDRESS _ CITY SEI STATE PROVINCE __
15. it s first use unplug the water dispenser for thirty 30 minutes then start it up again If you are not satisfied with the water dispenser performance check if there is enough room around the water dispenser to provide ample ventilation When the compressor is working it is normal to have a hot ra d iator Check the temperature setting of the cooling compartment Check that the cooling compartment door is closed tightly Check if the door is closed tightly Turn both thermostats down counterclockwise Once the compressor has stopped readjust starting from cold water thermostat Do not cause the compressor to start and stop frequently The cold water temperature tap may freeze up under extreme conditions When the cooling compartment is loaded and the compressor is running continuously while the bottled water is not consumed there can be an overcooling of the cold water tank To unfreeze the cold water tank turn the power switches for the cold water and cooling compartment off If you need to unfreeze it in a hurry then remove the water bottle and keep on draining hot water and pouring it back into the water receptacle Once the tank is unfrozen turn on only the cold water amp cooling compartment switch If you have time then just turn on the cooling compartment switch and turn off the cold water amp cooling compartment switch If you will be continuing to use the cooling compartment keep the door closed and reduce the cooling
16. lem 1 The power switch for the cold amp cooling compartment are turned on but the compressor is not Starting up 2 The water dispenser operation is noisy 3 The radiator at the back of the water dispenser is very hot 4 The contents of the cooling compartment are not cold enough 5 The compressor works non stop 6 The cold water tap is not working The cold water tank is frozen 7 The cold water tank is frozen and the cold water amp cooling compartment switch is on 8 The cold water is warm 9 The taps are leaking 10 Water is dripping out of the water dispenser and onto the floor NO 0101 Check if la 1b 4a Ab 5a 5b 6a 6b 6c 7a 7b 7C 8a 8b 9a 9b The power cord is plugged in properly If the water dispenser is brought in from outside in the winter time give it a few hours to warm up to room temperature before plugging it in The thermostat setting may be affected by the coldness of the water dispenser itself or the bottled water If the ambient room temperature is lower than the thermostat setting or the water dispenser itself is cold then the compressor will not start up It is not advisable to make any adjustments to the thermostat setting before the water dispenser and bottled water is warmed up to normal room temperature Check if the water dispenser sits on a level surface without rocking If the water dispenser is noisy after
17. omments or service info rmation please call 1 877 383 6399 8 30 a m 5 30 p m E S T F licitations pour l achat de votre nouveau distributeur d eau Sunbeam Avertissements et pr cautions Le distributeur d eau doit tre laiss en position verticale pendant au moins dix 10 heures sans tre branche Pendant la livraison et ou l entreposage le fluide l int rieur du compresseur se d placera Pour viter tout dommage l unit vous devez accorder le temps suffisant pour que le fluide se replace Avant de placer la bouteille d eau sur l appareil s assurer que le bouchon de drainage situ l arri re est bien serr Laisser un espace d au moins 10 cm entre l appareil et le mur Laisser un espace d gag d au moins 5 cm de chaque c t de l appareil Installer une bouteille d eau sur le distributeur d eau avant de brancher Assurez vous de remplir un verre de 12 oz d eau partir de chaque robinet avant le branchement de l appareil REMARQUE Branchez l unit Une fois que ceci est fait mettez les interrupteurs l arri re de l unit en position ON Il faut attendre environ 15 minutes pour obtenir de l eau chaude et moins d une heure pour de l eau froide Pour toute question ou pour obtenir de l information concernant le service composer le 1 877 383 6399 8h30 17h30 H N E Felicidades por la compra de su nuevo distribuidor de agua Sunbeam Advertencias y precauciones a tener en
18. pers away from the back of the unit Do not operate this or any other appliance with a damaged cord No other appliance should be plugged into the same outlet Be sure that the plug is fully inserted into the receptacle e Do not run cord over carpeting or other heat insulators Do not cover the cord Keep cord away from traffic areas and do not submerge in water e We do not recommend the use of an extension cord as it may overheat and cause a risk of fire If you must use an extension cord use No 14 AWG minimum size and rated not less than 1875 watts e Unplug the water dispenser before cleaning or making repairs Do not plug your water dispenser into the power outlet or turn the power switches on when the water dispenser is empty e Exercise caution and use reasonable supervision when the appliance is used by or near children e Do not use your water dispenser outdoors Place the water dispenser away from direct sunlight and make sure that there is at least 4 inches of space between the back of your unit and the wall Keep a minimum distance of 2 inches on each side of your unit free e Do not use this product to dispense anything other than water e Do not flick the power switches quickly on and off The resulting power surges may damage your water dispenser e Always turn your water dispenser off when there is no water left in the bottle or when you are changing bottles Turn it back on after the new bottle has been place
19. time periods listed above and subject to the conditions provided for in this policy For warranty service find the nearest Authorized Service Dealer by calling 1 877 383 6399 Warranty service may only be performed by a Prestige Home Comfort Inc Elite Group Inc Authorized Service Dealer STAMP HERE WARRANTY CONTROL CENTER PRESTIGE HOME COMFORT 1175 Place du Frere Andre Montr al QC Canada H3B 3X9 1 877 383 6399 8 30am 5 30pm E S T te a Sunbeam is a registered trademark of Sunbeam Products Inc used under license
20. tor for the L E D indicator light Heating power switch NO 19 Auto reset thermostat for the hot water 20 Protection diode for the LED indicator light 21 Power on LED indicator light 22 Diode for the LED indicator light 23 Resistor for the L E D indicator light DD Sa a 3 o Thermostat for the hot water go Heater PRESTIGE HOME COMFORT ELITE GROUP LIMITED ONE YEAR WARRANTY POLICY EFFECTIVE APRIL 2005 LIMITED WARRANTY Prestige Home Comfort Elite Group Inc hereinafter referred to as PHC EG hereby warrants subject to the conditions herein stated in the paragraphs below that should this product become defective by reason of improper workmanship or material defect during the specified warranty period PHC EG will repair or refund the same effecting all necessary parts replacements Transportation charges on parts submitted for repair or refund under this warranty must be borne by the purchaser THERE IS NO OTHER EXPRESS WARRANTY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE TIME PERIOD SPECIFIED OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW WARRANTY PERIOD Consumer Residential Use Only Water Coolers Dispensers 50 Days PHC EG warrants that from the date of purchase this product w
21. torisation Fabriqu pour Prestige Home Comfort une filiale de Elite Group Inc Montreal Canada H3B 3X9 2005 Sunbeam Products Inc Todos los derechos reservados 1 Ss 8 7 7 a 3 8 3 z 6 3 9 9 Sunbeam es una marca registrada de Sunbeam Products Inc uso bajo licencia 8 30am 5 30pm E S T 8h30 17h30 HNE 8 30am 5 30pm E S T E Fabricado por Prestige Home Comfort una subsidiaria de Elite Group Inc Montreal Canada H3B 3X9 service lima g ehom eprod ucts com D AAA ATT A A A A Sunbeam Water Dispenser Warnings amp Precautions Your water dispenser must be left upright for at least ten 10 hours unplugged During delivery and or storage the fluid inside the compressor will move To avoid any damage to the unit you must allow adequate time for the fluid to settle Before placing water bottle on unit be sure that the drain plug on the back is tightly fastened This unit should be placed with at least 4 10cm between the back of the unit and the wall Keep a minimum distance of 2 5cm on each side of your water dispenser free Mount a full water bottle onto your dispenser before plugging in your water dispenser Make sure to fill one 12 oz glass of water from each tap before plugging in the unit NOTE Plug in the unit Once this is done put the switches at the back of the unit in the ON position You should have hot water in approximately 15 minutes and cold water in less than 1 hour For questions c
22. water and or the cooling compartment turn the corresponding thermostat clockwise to set the temperature colder and counterclockwise to set the temperature warmer When the temperature of the fridge or the water is set lower the compressor will take a longer time to reach the set temperature than if it is set higher but this will not affect the life of the compressor This cooling compartment is not a frost free unit Minor ice build up in the compartment is normal and expected Warning If the water and or refrigeration thermostat is set at 6 for an extended period of time there is a possibility of freezing in the water tank or in the interior of the cooling compartment WATER DISPENSER MAINTENANCE NO 0101 WATER TANK CLEANING INSTRUCTIONS Do not flick the power switches quickly on and off The resulting power surges may damage your water dispenser NO Always turn your water dispenser off when there is no water left in the bottle or when you are changing bottles Turn it back on after the new bottle has been placed and the air is purged from the dispensing buttons UJ lt To clean the unit first unplug the power cord Wipe the outside of the water dispenser with a soft cloth dampened with liquid dishwashing soap Use toothpaste to remove spots on the cabinet Twist the bottle receptacle of the No Spill system counterclockwise and pull it up Fig A Ul a Take apart the No Spill system

Owner`s Manual (General)

Contents

Download Pdf Manuals

Related Search

Related Contents