Home

Guide of Main Menu - Pdfstream.manualsonline.com

1. Press to display the programme information box on the screen And this button functions same as the RED button on the menus SOUNDTRACK GREEN Press to display the soundtrack list for the current service And this button functions same as the GREEN button on the menus SUBTITLE YELLOW Press to display the subtitle language list for the current service And this button functions same as the YELLOW button on the menus UHF BLUE Press to set the UHF menu This button functions same as the BLUE button on the menus TIME WHITE Press to display the current time on the screen Press to reserve services on the Informaion box or EPG And this button functions same as the WHITE button on the menus EXIT Press to return to the previous menu and screen VAN Volume up down buttons Press to increase or decrease the volume STANDBY Press to switch between Operation and Standby modes D d B TV SAT Press to select the TV SAT mode TV RADIO Press to switch between TV and Radio modes MUTE Press to temporarily cut off the sound MENU Press to display the Main Menu on the screen or return to the screen from a sub menu screen CURSOR Press to move the highlight bar for selecting options on the menus And this button is used to change services up down and increase or decrease the audio volume OK Press to display the service list This button is used to select
2. The Motorised System is used to set the DiSEqC 1 2 motor by Eutelsat specification If you wish to use this system please refer to page E42 E32 Guide of Main Menu Service Search OSD e If you press the EXIT button during the search then Service Search stops and the searching menu will appear e When you find all the services the following picture appears e Before saving it you can select the services you want to delete Found services OSD e The picture above shows services that are found after Manual Search e Use the RED CD button to mark the services that you want to delete To unmark a service select the service and press the RED CD button again e Press the OK button to save or press the EXIT button to exit without saving e Then Service Search menu appears again When you exit from all menus the first service of the found service list is played In the bottom of found service picture network the information of transponder and the number of found service that the services belong to are displayed The deleted service by the RED CD button is excepted from counting of the number of services The deleted service is not included in this number Free applies to the empty space of the memory It will be used to store future services E33 Manual Search Set the search parameters Frequency Symbol Rate etc to manually find the services that you have selected in the transponder The bar on bot
3. When you want to change the audio language of current service press the GREEN button firstly The on screen menu is displayed on the top to left side of the screen To change the audio language 1 lt gt buttons Use to select the audio on the left right or both 2 4 buttons Use to select the audio language you want 3 OK EXIT button When this button is pressed the Soundtrack OSD will disappear keeping the selected Soundtrack language constant When the current service is switched the audio language returns to the audio language that was selected in previous service If the returned audio language is invalid the audio language that you selected from the audio language menu has the priority of playback Soundtracks broadcast in Dolby Digital are indicated by Dolby Digital symbols either side of the respective language selection in the menu By selecting such a soundtrack the Dolby Digital audio will be output by the optical S PDIF on the STB This can be decoded by an external Dolby Digital television or amplifier for example Subtitle When the current broadcasting programme provides subtitle press the SUBTITLE button to see the current subtitle language list To change the subtitle language 1 Use the 4 buttons to select a Subtitle language you want 2 Press the OK button and the selected language is highlighted and then the Subtitle Language you want is displayed on the screen Press the E
4. W lt buttons to select the satellite you want to view When you have selected the satellite you wish to view go down to the Motor Control option and again using the lt gt buttons select go to and press the OK button The motor will now move to the position of the selected satellite The Movement option is used to fine tune the position of the motor When using the Movement option for fine tuning you must remember to store the changes you have made or else these will be lost N DARON SE E45 7 Searching for services on your selected satellite Once you have moved the motor into position you can search for the channels transmitted from the relevant satellite To search for services on your new selected satellite Do as follows 1 Move the motor to the position of the satellite you wish to search aie Betr g see section 6 above 2 Select the service searching from the Main Menu and press the am OK button To display the Service Searching menu 3 Select the manual search option and press the OK button to display the Manual Search menu 4 Now enter the Frequency and Symbol Rate using the NUMERIC buttons 0 9 Next enter the Polarisation and FEC values using the lt gt buttons 5 When you have entered all these details in press the OK button and the search will begin 6 When the search has finished press the OK button to view 7 Repeat the process for all the transponders you want from
5. s services are displayed on the right window 2 The scroll bar on left of the screen shows the location of the cursor in the Network The scroll bar on right of the screen shows the location of the service from the selected Network Service Genre 1 Press the BLUE button on the remote control unit to select the Genre service list 2 Use the a v lt gt buttons to select a service 3 Press the BLUE button to toggle Genre and service list Note The scroll bar on left of the screen shows the location of the cursor in the selected Genre The scroll bar on right of the screen shows the location of the service E17 Service Alphabet Order 1 Press the WHITE obutton on the remote control unit to select the Alphabet service list 2 Use the 4 v lt gt buttons to select a service 3 Press the WHITE C button to toggle Alphabet and service list Note The scroll bar on left of the screen shows the location of the cursor in the Alphabet The scroll bar on right side of the screen shows the location of the selected Alphabet service e NACI 5700 models are not applicable Service Satellite 1 Press the WHITE outton on the remote control unit to select the Satelite service list 2 Use the a v lt gt buttons to select a service 3 Press the WHITE button to toggle Satellite and service list Note The scroll bar on left of the screen shows the location of the cursor in the Satellite The scroll bar on ri
6. Press the OK button at timer option to display the Timer table The Timer determines the on off time and can also be used for VCR recording Timer Mode Wakeup Sleep timer determines the Timer Mode e Once _ The timer programming is applied only once e Daily The timer recording is applied everyday repeatedly e Weekly The timer recording is applied weekly Set one day in a week Use the lt gt buttons to select the type of timer programming Wakeup Time Select the time when STB is turned on Use the NUMERIC buttons 0 9 on the remote control unit to enter your Wakeup Time Wakeup Service No Use the lt gt buttons to set the service number provided for the set Wakeup Time Use the TV Radio button on the remote control unit to toggle TV Radio service Service Name The Service Name that has been determined by the Wakeup Service No will be shown Sleep Time Depending on Time Setting select the time when STB is turned off E23 Aa Cal par fering Mied a l d ll UHF Tardy E A EA A V Output Setting Video Output CVBS S Video RGB Set the video mode for the TV SCART output Audio Output Set the audio mode which is output from the TV SCART and RCA Cinch Jack Stereo Mono Dolby Digital If Dolby Digital option is ON and the broadcaster provides the Dolby Digital stream the Dolby Digital audio language is firstly selected when changing the service Screen Mode Select the aspect rat
7. The colour buttons function same as ones for Organise All services except the following differences e When you delete a service in the selected genre it will be available again on the All TV services list at the right side At that time the genre for the deleted service becomes etc e You can move the service only in the selected genre e Coloured buttons are available when the cursor is located in the middle window m kal MH P To select the Genre 1 Use the a button to move the cursor to Gr plate left 2 Select the wanted genre To group the services into a Genre 1 Use the gt button to move the cursor to services plate right 2 Select the service you want to group into Genre 3 Press the OK button 4 Use the lt button to move the cursor to Genre plate left 5 Press the OK button to save the selected group Note 1 Use the lt gt buttons to move the cursor 2 Use the buttons to select the previous or next page E28 Guide of Main Menu peim Adis Favicon bibi ee Di ee DN ea Be e oe E29 Organise Radio Services The Organise Radio Services functions same as TV Services except that it uses Radio Services You can delete or move Radio Services and change the attributes of them Organise All Services The Organise All Services lets the user Delete Move Lock Skip or Rename Radio services on the All Radio services list Organise Favourite
8. With Hi Fi System 1 Connect an RCA Cinch stereo cable from the AUDIO L R sockets on the back of the STB to the LINE AUX SPARE OR EXTRA input sockets on your Hi Fi system E9 1 SS SSSssss ia SNS SSSSSSSSS ASSSS TV with VCR and Motorised System DiSEgC 1 2 Connect one end of a 21 pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV Connect one end of a 21 pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN connector on your TV Connect one end of a RF lead to the RF IN connector on your VCR and the other end to the RF OUT connector on the STB Connect the coaxial cable from the LNB of your motorised system to the LNB IN socket on the STB Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1 2 motor E10 Remote Control Unit NUMERIC BUTTONS INFORMATION RED SOUNDTRACK GREEN SUBTITLE YELLOW UHF BLUE TIME WHITE EXIT V V E11 HUMAX RS 101P STANDBY TV SAT TV RADIO MUTE MENU CURSOR OK P P HELP EPG RCL Recall NUMERIC BUTTONS Press to select a service enter your PIN code or numeric on the menu 2 INFORMATION RED
9. want to locate Then the icon will be displayed in front of the service number 2 Use the a v lt gt buttons to select a new location 3 Press the OK button to fix the location 4 Press the EXIT button to return to the original location e Lock 1 Press the YELLOW button to lock services Then the symbol rC will be displayed at the right side of the service name 2 Enter the PIN code to view the locked services e Skip 1 Press the BLUE button to skip services Then the symbol will be displayed at the right side of the service name 2 Use NUMERIC buttons 0 9 service list or EPG button to view the skipped services when selecting channels Note You can t view the skipped services by using buttons e Rename 1 Press the WHITE Cc button to change the service name Then the keyboard image will be displayed on the screen 2 Key in the new service name You can use the four direction keys to move or select the services A to move the previous service v to move the next service ad to move back by services gt to move forwards by services Note The box between service list and the description of the colour buttons offers the brief information of a service where the cursor is located E26 Guide of Main Menu Lausargss Fascugante Pa Sere os ms See e E27 Organise Favourite A D Each of TV and Radio has four Favourite groups E
10. During the search services that are found are displayed as follows 1 Press the EXIT button during Automatic Search to stop search 2 After the search is finished the appearite message appears 3 Press the OK button to return Service Search menu Bkarai Dame Core IEISnRA 4 4 Status STB Status Displays the information of H W Version S W Version Loader Version and Cl CAM of STB and so on e F1 5000 doesn t support CI CAM Signal Detection Shows the Signal Level AGC level and Signal Quality BER of the current service and is help to the initial antenna setting STB Upgrade You can download and upgrade the software of this STB viaa satellite when the software of new version is released Do not turn off the STB during downloading When the power is switched OFF turn on the STB and the process will be continued e CRCI 5500 models are not applicable 4 5 Common Interface You can enjoy not only scrambled services using the Conditional Access Modules CAM but also Free To Air services This STB currently supports six kinds of CAM VIACCESS Nagravision CONAX CryptoWorks TM Irdeto or Mediaguard Common Interface module and Smart Card depend on the service provider If you need CAM contact your service provider or distributor Note If CAM is not used then only Free To Air services are available e F1 5000 VA 5200 models are not applicable E38 Guide of Main Menu General besen Seed i
11. Nagravision by service provider Other channels have the number from 101 in sequence as the receiver searchs the signal e Specifications are for NACI 5700 models GB3 Glossary Glossary e Antenna A device that collects and radiates electromagnetic waves Includes a satellite dish and abroadband antenna e Forward Error Correction FEC A system of error control for data transmission e Frequency The number of cycles or events per one second which is expressed in the unit of Hertz Hz e Intermediate Frequency IF A frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception e Low Noise Block LNB Downconverter A low noise microwave amplifier and converter which downconverts a range of frequencies to IF range e Packet Identifier PID A set of numbers that idenitifies transport stream packets containing data from a single data stream e Polarisation Characteristic of an electromagnetic wave determined by the orientation of the electricfield vector e Quaternary Phase Shift Keying QPSK Phase shift keying in which four different phase angles are used e Service A channel to which a decoder or TV is tuned e Transponder An automatic device that receives amplifies and retransmits a signal on a different frequency E4 Reference 1 Connect DiSEqC 1 0 All our receivers are designed to be DiSEqC 1 0 compatible This allows multiple antennas to be connected to the S
12. PDIF RS 232C Transfer rate 115 200 bps 9pin D sub Type RF Modulator RF Connector 75Q IEC 169 2 Male Female Frequency 470 860 MHz Output Channel CH21 69 CH28 69 or CH13 62 for the Remodulator TV Standard PAL G B D K selectable by Menu setting Preset Channel CH36 or TBD Software changable by Menu Power Supply 190 250V AC 50 60 Hz SMPS Max 35W Standby Power lt 11W Protection Separate internal fuse The input shall have lightening Protection 0 C to 45 C 10 C to 70 C Storage Humidity 5 95 RH Non Condensing e Please note The specification of the STB may be changed without notice in advance E50 www humaxdigital com HOMM 10E
13. This mode allows you to customise add a new service and displays the state of the STB Enter the submenus after selecting the Installation mode in the Main Menu 4 1 System Setting The System Setting mode supports the STB internal settings according to the connection of the receiver and external units This mode includes Language Setting Time Setting A V Output Setting UHF Tuning and Other Settings Language Setting Select the language for menu audio or subtitle 1 Select the highlighted language setting using the 4 buttons in the system setting mode and then press the OK button 2 Select the highlighted Menu or Audio Subtitle Language and press the lt gt buttons and the language list will be displayed 3 Use the 4 buttons to move to a language you want and then press the OK button to finish setting Menu Language We support the various menu languages of Europe amp Middle East areas For Europe areas there are Czech Danish English French German Hungarian Italian Portuguese Russian Spanish Swedish Turkish and more Also it includes Arabic English French German Italian Persian Russian Turkish for Middle East areas e The kind of languages can be changed depending on the country Languages are subject to change without prior notice Audio Language Select the default language for audio when changing services If you change the current service your STB will initially select the previo
14. appropriate menu Note 2 F1 5000 VA 5200 models are not applicable Note 3 Refer to the instructions on the appropriate menu Note 2 Note 3 E48 Specification Tuner amp Channel IF IF Band width LNB Power amp Polarisation 22 KHz Tone Transport Stream Profile Level Aspect Ratio Video Resolution Audio Decoding Audio Mode Sampling Memory Main Processor Graphic MPEG amp System DRAM 950 2150 MHz 75Q unbalanced 25 to 65dBm 480 MHz 36 MHz Vertical 13 5V Horizontal 18V Current 500mA Max Overload Protection QPSK 2 31 Ms s Convolutional Code Rate 1 2 2 3 3 4 5 6 and 7 8 with Constraint Length K 7 MPEG 2 MP ML 60 Mbit s Max 4 3 16 9 720 x 576 MPEG MusiCam Layer amp II TMIPS R3930 81MHz 2Mbyte 4Mbyte 4Mbyte CAS Embedded You can use a special antenna switch with DiSEqC commands When changing ASTRA1 to EUTELSAT for example a DiSEqC command is sent with the 22KHz tone through the antenna cable The antenna switch will change ASTRA1 to EUTELSAT The concept of DiSEqC is a protective trademark of EUTELSAT Data rate decides the picture quality of digital TV programmes Data rate of about 5 6 Mbit s coincides with the picture quality of a analog TV programme E49 A V amp Data In Out TV SCART Video Output CVBS S Video RGB Audio Output VCR SCART Video Output CVBS Video Input CVBS S Video RGB VIDEO AUDIO R L S
15. find FEC You can select the value of 1 2 2 3 3 4 5 6 7 8 or Auto LNB Power As there is whether the LNB Power of STB is necessary or not according to the sort of IF IF converters select a suitable option for situation Automatic Search When you enter the Satellite Name that is set in Antenna Setting menu search all of the selected satellite without inputting the extra frequency Antenna Alternative Select the target antenna for Automatic Service Search The attribute of this antenna alternative number is already set in Antenna Setting menu and the Satellite Name is helpful in the selection of the antenna but in this menu you cannot change the Satellite Name Search Type e You can select one of two modes Quick or Detail e When you select Quick mode it searches the service by search e parameters that is preset e When you select Detail mode it searches the service through all field of tuner 950 2150MHz Network Search e You can select Yes or No When you select Yes you can find more transponders using the home network e As it refers to NIT during searching if there is the frequency information of other transponder it searches the other transponder besides the transponder that the user inputs E36 Guide of Main Menu EHTK Wap ree Benz E37 Detail Mode The pre fixed symbol rate list is changed according to Antenna Alternative and Satellite Name If you want to add or chang
16. firmly to the STB and TV VCR Check that you have selected the correct channel or Video Output on your TV If you are using the RF Output check that you have correctly tuned the UHF channel of the STB or TV Check the brightness level of the TV Poor picture quality See No Picture above Check the signal level if this is low then try adjusting the alignment of your dish No Sound See No Picture above Check the volume level of the TV and STB Check the Mute status of the TV and STB Remote Control does not operate Point remote control directly towards the STB Check and replace batteries On Screen Error Messages No or Bad Signal Check the LNB replace LNB if necessary Check the cable from the LNB Check the position of the dish realign dish if necessary If you are using a DiSEqC 1 0 switch check that you have connected the LNBs to the correct connections on the switch Check the Signal Level and the Signal Quality in the Signal Status menu Service is not running or scrambled No access to the service slot Check whether the Common Interface module and Smart card are correctly inserted Check whether the Common Interface module and Smart card is appropriate for the selected service Please check the card No right for this service No smart card in slot and please insert your card when using the CAM Check that the Smart card is inserted correctly Check t
17. programmed list see 3 above To do this you must access the Satellite Settings menu Do as follows 1 2 10 Use the lt gt buttons to stop the motor when required 12 13 14 Select Service Searching from the main menu and press the OK button to display the Service Searching menu Select the Manual Search option and press the OK button to display the Manual Search menu Select the relevant Antenna Alternative that you are using for this satellite Enter the Frequency Polarisation Symbol Rate and FEC of a transponder on the satellite you wish to find This transponder information should be unique to this satellite Select the Antenna Alternative option and press the OK button to display the Satellite Settings menu Highlight the option DiSEqC Command Mode and using the lt buttons change this to Installer Highlight the option Satellite name and use the lt gt buttons to select the satellite you want to find use others if the name of the satellite you want does not appear When you have selected the satellite you wish to find go down to the Movement option and again using the lt gt buttons to start the motor moving You should move the motor as far west as possible and the move it east so that you cover the complete movement range of the motor During the move from west to east the Signal Quality bar should register a signal once This is the position of the satellite If ther
18. three blocks by 30 minutes per block E20 Guide of Main Menu 3 Parental Control You can set a parental guidance rating to each programme in this mode 1 When the OK button is pressed after selecting the highlighted parental control on the initial menu screen a display window for entering the PIN code will appear on the centre of screen The default PIN code is l 2 Enter the PIN code on the display window If any problem occurs when entering a PIN code you cannot switch to the next mode Paama Cone cd 3 Set the parental guidance rating of highlighted censorship classification The parental level is given as age based numbers no block 6 10 14 18 and total block Enter the PIN code to unlock or lock programmes 4 To change your PIN code e Select the highlighted Old PIN code using the A g buttons and then enter your Old PIN code e Enter a New PIN code in the highlighted New PIN code using the 4 buttons e To verify the New PIN code re enter a New PIN code in the highlighted Verify Changed PIN code 5 When the entered PIN code is correct then all settings are completed If the PIN code is wrong the message PIN code mismatch will be displayed on the display window When the OK button is pressed at this time the Old PIN code is valid and the cursor is located in the first position of this menu E21 REATTT KUCK TSP Lome beri Lmg Berzra La Mrih ray 4 Installation
19. www humaxdigital com E46 Menu Map MAIN MENU Select Service TV Guide Parental as PE System Setting Service Organising Language Setting Menu Language Organise All Services Audio Language Organise Favourite A D Subtitle Language Organise Service Genre Time Setting Current Time Organise Radio Services Organise All Services Timer Organise Favourite A D Timer Mode Organise Service Genre Wakeup Time Organise Networks Wakeup Service No Sleep Time Delete Satellites Video Output Audio Output Dolby Digital J Screen Mode i Display Format NTSC Mode A V Output Setting Channel PAL Standard Offset UHF Tuning Other Setting OSD Transparency Info Box Display Time Menu Background Changing to Reserved Service Menu Mode E47 Installation Service Searching Antenna Setting Manual Search Advanced Search SMATV Search Automatic Search Antenna Alternative Satellite Name LNB Frequency 22KHz Tone 0 12Volt Switch DiSEqC Input Motorised System Antenna Alternative Frequency Polarisation Symbol Rate FEC Network Search Automatic Skip Antenna Alternative Frequency Polarisation Symbol Rate FEC Video PID Audio PID PCR PID Frequency Symbol Rate FEC LNB Power Antenna Alternative Satellite Name Search Type Network Search STB Status Signal Detection Note 1 Note 1 Refer to the instructions on the
20. A D The Organise Favourite A D lets the user Delete Move Lock Skip or Rename Radio Services from the Favourite Radio Services and group into a new Favourite Radio Services The Radio Services are grouped into a Favourite in the same way as the TV Services refer to page E27 Organise Service Genre The Organise Service Genre lets the user Delete Lock Skip or Rename Radio Services and group into Radio Service Genres Radio Genres include Pop Rock Country Classic Jazz Folk News Show Sports Education User A D etc The Radio Services are grouped into a Genre in the same way as the TV Services refer to page E28 Organise Networks LA Ge Peer a RN You can edit services using the network unit yo H e The provider names are displayed on the left side of screen i Ex and the TV Radio Services included in the highlighted Wa Network are displayed on the right side of screen Only the Delete Move Rename Function can be used in this mode e When TV Radio Services are too many to be displayed use the gt button to move the cursor to the right window and use the a v and Mis buttons to move the cursor to the next list When the number of services is under 10 NTSC 8 the scroll bar is not displayed In Radio Service icon JJ is marked in front of service number Delete Satellites 1 Press the a v lt gt buttons to move to the satellite Tp or ALL you want to delete 2 Press the RED Ci_ button t
21. Digital Set Top Box Free To Air Common Interface Viaccess Embedded CryptoWorks Embedded Nagravision Embedded User s Manual F1 5000 CI 5100 VA 5200 VACI 5300 CRCI 5500 NACI 5700 E1 Contents Eeer E2 COPYN e E3 GOSS AI EE E4 Rene E5 E6 STB Connechons E7 E10 Remote Control UNT dsini a E11 E12 Gude Of FUNCIONS E E13 E14 Guide of Main Men E15 E41 Motorised System 06 s cccccicessceceeeeteceeeeeeseesnceeee E42 E45 Troubleshooting Guide cccceecseeeeeeeeeeaeeeeeeeeeeens E46 Men MaD EE E47 E48 See Lee Te EE E49 E50 Safety This STB has been manufactured to satisfy the international safety standards Please read the following safety precautions carefully MAINS SUPPLY OVERLOADING LIQUIDS CLEANING VENTILATION ATTACHMENTS 190 250 V AC 50 60 Hz Do not overload a wall outlet extension cord or adapter as this may result in fire electric shock The STB shall not be exposed to dripping or splashing and that no objects filled with liquids such as base shall be placed on the apparatus Disconnect the STB from the wall outlet before cleaning Use a light damp cloth no solvents to dust the STB The slots on top of the STB must be left uncovered to allow proper airflow to the unit Do not stand the STB on soft furnishings or carpets Do not expose the STB to direct sunlight or do not place it near a heater Do not stack electronic equipments
22. TB simultaneously If you have two or more fixed antennas or LNBs you can use a DiSEqC 1 0 switch 1 Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch 2 Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input connector of the DiSEqC switch 3 Do the same for other LNBs 4 Connect one end of a Coaxial cable to the RF output connector of the DiSEqC switch and the other end to the LNB IN socket on the STB 2 Connect DiSEqC 1 2 Please refer to page GB42 The Locking Time might take longer than expected during the initial boot if the motorised system is set enable mode 3 Connect a Satellite antenna To the digital receiver you can connect either a single satellite antenna directly or through converter box several antennas or LNB of multi feed equipment You can connect a further Sat receiver for example analogue with the receiver of common antenna equipment that has satellite signals e Connect an antenna cable through converter boxes 1 When you assemble several antenna or a multi feed equipment that has several LNB or LNB with several exits connect each cable from the antenna to a converter box 2 Connect the output of converter box to LNB IN as in example displayed 3 When you use a converter box of 0 12V steerage connect it to the output 0 12V additionally For converter boxes of 22KHz or DiSEqC steerage you can skip thi
23. XIT button to cancel the Subtitle mode Teletext Use your TV Remote Control Unit to control the Teletext service The teletext button doesn t exist on the STB Remote Control Unit When the service supports Teletext the Teletext icon EI is displayed on the I plate E14 Guide of Main Menu 1 Select Service The select service displays the required service list which can be viewed in Simple or Advanced mode 2 TV Guide Your STB has an Electronic Programme Guide EPG to help you navigate through all the possible viewing options The TV Guide supplies information such as programme listings and start and end times for all available services In addition detailed information about the programme listings and start and end times for all available services In addition detailed information about the programme is often available in the EPG the availability and amount of these programme details will vary depending on the particular broadcaster 3 Parental Control Access to services and programmes is controlled by a PIN code e a 4 digit secret code that is defined by the user The very first time you attempt to lock all services or lock programmes by ratings the on screen menu will instruct you to assign a PIN code Later on if necessary you can change it 4 Installation The Installation mode allows you to have the information of setting services and newly set services language time organise search Fu
24. a set top box to set top box download copies the software of the main unit into slave unit b pc to set top box download downloads the software directly from pc to the model requiring upgrade c OTA over the air downloads the software where the manufacturer reserves the right to decide when and where to release through satellite system Over The Air OTA is simply another alternative for downloading software versions However the manufacturer reserves the right to decide when and where this software upgrade can take place by beaming latest software versions over the air via satellite systems Note that OTA is only limited to certain geographical regions mainly due to different satellites having different footprints area where the signal can be received SUSS TM is an official trademark and logo for HUMAX loader software to perform OTA The software upgrade via satellite system will only occur under the following circumstances 1 the equipment should have appropriate loader software 2 the manufacturer decides to release software downloading via a designated satellite system 3 the equipment must be tuned properly to the same satellite that the manufacturer uses e Note CRCI 5500 complies with the OTA type of CryptoWorks E6 STB Connections Front Panel F1 5000 Free To Air CI 5100 2 Slot Common Interface VA 5200 2 Smart card e Warning To install the unauthorized CAM into CI slot can c
25. ach Favourite group contains up to 100 services Delete Move Lock Skip or Rename each TV service in a Favourite TV group and re group them into your Favourite TV group This mode has the same operating methods as organise all services e When you delete a service in the Favourite group it will be available again on the All TV service list This allows the service to be removed from the Favourite group e You can move the service only within the Favourite group e Coloured keys are available when the cursor is located in the middle window Except when the middle window is disabled grey To select the Favourite group 1 Use the a button to move the cursor to Gr plate left 2 Select the wanted favourite group To group the services into Favourites 1 Use the button to move the cursor to services plate right 2 Select the service you want to group into Favourites 3 Press the OK button 4 Use the a button to move the cursor to Favourites plate left 5 Press the OK button to save the selected group Note 1 Use the lt gt buttons to move the cursor 2 Use the buttons to select the previous or next page Organise Service Genre Shyer Shee od TV Bore be ER RS E EC The Organise Service Genre feature allows the user to E q EK Delete Lock Skip Rename a service in the selected Genre el Du A Available genre Movie News Show Sports Children Music K Art Education etc
26. al Search option and press the OK button you should now see the Manual Search menu 3 Highlight the Antenna Alternative option and press the OK button You should now be in the Satellite Settings menu Press the CiD button to access the Motor Limit Setting menu 5 Highlight the Limit Setting option and use the lt gt buttons to disable this Warning When this option is disabled your motor will be able to move beyond any limits that have been stored please take care in case there are anything obstructing the path of your dish 6 To set the East Limit a Select Movement and use the lt gt buttons to move your motor East or West until the motor is at the position you wish to use as your East Limit Use the lt gt buttons to stop the motor at the correct position b Highlight the Store East Limit option and press the OK button to store the current position as your East Limit E43 To set the West Limit a Select Movement and use the lt buttons to move your motor East or West until the motor is at the position you wish to use as your West Limit Use the lt buttons to stop the motor at the correct position b Highlight the Store West Limit option and press the OK button to store the current position as your West Limit 5 Manual Satellite Search The purpose of this is to set the motor position for each satellite manually This is useful if the satellite you require is not available from the pre
27. ause the wrong operation Do not reinstall the CAM of the already embedded CAS to prevent the wrong operation E7 Front Panel VACI 5300 CRCI 5500 NACI 5700 2 Slot Common Interface 1 Smart card TV LED AMBER The LED lights on in TV mode RADIO LED GREEN The LED lights on in RADIO mode DISPLAY Shows service number error messages RCU commands and time in Standby mode STANDBY LED RED Indicates that the STB is under standby Rear Panel 13 18 Volt LNB IN Use to connect an antenna LNB OUT Use it when connecting to another STB RS 232C Use it when connecting to your PC TV SCART For the audio video input of the TV VCR SCART For the VCR STANDBY Press to switch between Operation and Standby modes TV RADIO Press to switch between TV and Radio modes Cie A Use to change services down up SLOT For a two CA Module with a smart card SMART CARD For a Smart cards 0 12V OUT 50mA Dolby and the double D symbol are boratories trademarks of Dolby Laboratories O AUDIO VIDEO OUTPUT Audio video signal from your STB to VCR or TV 0 12V OUT For an external LNB switch RF OUTPUT Use to connect a RF signal from your STB to RF ANT input jack on your TV RF INPUT Use to connect a general Aerial Antenna and CABLE jacks to a RF input jack on the STB S PDIF Output for c
28. e are two or more different positions which registers a signal then you must choose another frequency that is unique to the satellite you want Use the Signal and Strength Quality bar at the bottom of the screen to judge the best position of the dish When you have the best position of the dish go to the Motor Control option and using the lt gt buttons select store and press the OK button The position of the satellite should now be stored If you do not store this position it will be lost when you exit the menu Repeat the process for each satellite if required remembering to use a different antenna alternative for each satellite E44 Motorised System 6 Moving to a pre set Satellite Once you have stored the positions of the satellites you want see left below you can now search for the services transmitted from them Before you can do this you must move the motor to the position of the satellite you wish to search To do this you must access the Satellite Settings menu Do as follows Select Service Searching from the Main Menu and press the OK button to display the Service Searching menu Select the Manual Search option and press the OK button to display the Manual Search menu Select the Antenna Alternative option and press the OK button to display the Satellite Settings menu In the Satellite Settings menu ensure that you have DiSEqC Command Mode option set to User Highlight the option Satellite Name and use the
29. e it press the RED CD button The value of Pre fixed symbol rates can not be editable 22000 27500 The picture of the Symbol Rate Add Change mode is as follows 1 When you press the RED CD button after entered to detail mode from search type yellow box will be trimmed with red edges meaning edit is possible 2 You can easily put optional value with using NUMERIC buttons 0 9 3 Press the RED CD button for confirmation and you will successfully exit from input mode If press the OK button at symbol rate value input mode the value will be confirmed and if you moves left or right column use the lt gt buttons you can differ values of symbol rate to input Then press the EXIT and the RED CiD button to exit from input mode To delete a Symbol Rate in the above list press the O NUMERIC button in the selected position and then the symbol rate disappears The range of Symbol Rate that is input additionally is 16 30Ms s Note The user should select the Satellite name in Antenna Setting menu When the user types the Satellite Name separately the search type is fixed to the Detail mode Press the OK button anywhere to start Automatic Search The picture during searching is as follows The picture searches with varying frequency Symbol Rate and FEC etc Satellite Name is the name that the user selects to correspond with Antenna Alternative of Antenna Setting The progress bar appears on bottom of the picture
30. e right display window The selected OSD will be highlighted every time the cursor moves To reserve a programme you want e Select a programme you want by using the C C buttons or A V buttons And then press the WHITE button Press the lt gt buttons to watch the programme of previous page or the programme of next page Press the YELLOW button to watch the Reserved programme list Weekly mode Shows the information of programmes that will be played for a week To watch a programme you want through the display window e Press the OK button and then press the 4 buttons to select a programme you want Press the OK button again To reserve or cancel programme reservation e Select a day you want using the 4 buttons Press the lt gt buttons to select a programme you want and then press the WHITE button Reserved mode Shows the programme lists that you have already reserved on the TV Guide or Information box Maximum eight programmes can be reserved This programme list includes service name date duration time reservation mode and event name To cancel the Reserved service select a programme you want to cancel using the 4 buttons and then press the WHITE button Shows a simple TV Guide like an Information box This mode shows in the A V playback mode e Red vertical line Indicates the current time e Black white bar Shows the proceeding state of programme e Time range of bar This consists of
31. ght side of the screen shows the location of the selected Satellite service e Specifications are for NACI 5700 models E18 Guide of Main Menu DUT DR Kee E19 2 TV Guide You can watch a programme being shown and reserve it in the TV Guide mode To enter the TV Guide mode Press the EPG E9 button on the remote control unit or select the TV Guide on the Main Menu To select the TV Radio Guide Press the TV Radio button on the remote control unit and TV Guide will be switched to the Radio Guide TV Guide mode includes four different modes To select each mode use the following buttons e RED CD button Use to display the current and next programme list e GREEN C button Use to display the programme list for one week e YELLOW C button Use to display the reserved programme list e BLUE button Use to display the simple TV Guide list Quick mode Now Next mode Show the informations of the programmes that are played now or will be played next time This mode consists of the service name event name event duration time current time and on screen display window To watch a programme you want through the display window e Use the fie buttons to select a programme you want The selected service will appear on the right display window e Use the a v buttons to select a programme you want And then press the OK button on the remote control unit The selected service will appear on th
32. he Smart card is appropriate for the selected service Check the subscription rights of the Smart card Time Display The front panel does not display the time Make sure you have switched on the STB Switch the STB on and tune to a service to allow the STB to receive the time sent with the signal by the service provider Front panel will only display the time in Standby mode Time displayed on the front panel is incorrect Adjust the time in the Time Settings menu Service Search No Signal in Manual Search Check the Signal Level and the Signal Quality in the Signal Status menu Check the LNB replace LNB if necessary Check the cable from the LNB Check the position of the dish realign dish if necessary DiSEqC 1 0 Check that you have connected the LNBs to the correct connections on the switch Check that you have set the correct settings in the Antenna Setting menu DiSEqC 1 2 Check that you have selected this in the Antenna Setting menu Check that the dish is aimed at the correct satellite Front Panel Error Messages dE Incorrect data block CRC 16 Try switching STB power Off and On Invalid system ID Check whether the system ID is different for Software and STB H UE UART RX TX time out Try switching STB power Off and On e f you can t solve the problem even referring this Troubleshooting Guide contact us via our homepage Homepage http
33. io of TV which is connected to STB 4 3 or 16 9 Display Format Select the format which the video is to be displayed on screen When your TV set is 4 3 and video source is 16 9 STB will display in Letter box or Centre mode as selected When your TV set is 16 9 and video source is 4 3 STB will display in the Pillar box or Full mode as selected NTSC Mode Adjust this value between 3 58 and 4 43 if your TV displays the video only in black and white color Normally NTSC 3 58 mode is used worldwide but some TV sets can support only NTSC 4 43 mode UHF Tuning You select the STB output by using the UHF channel Channel Select an UHF channel The range of channels and frequency value are different for each PAL Standard PAL I G for Europe CH21 CH69 PAL B for Europe Australia CH28 CH69 PAL D for China CH13 CH62 PAL K for Russia CH21 CH69 PAL Standard Select a PAL Standard according to the above range of channels Offset Adjust the fine tuning value The Offset ranges from 4 to 4 and each Offset represents 1MHz E24 Guide of Main Menu Other Setting Select the OSD Transparency Information Box Display Time and so on OSD Transparency Select the OSD Transparent type It affects Information box Soundtrack Subtitle Service list Time and Quick mode of TV Guide Use the lt gt buttons to toggle transparent opaque 20 40 60 and 80 Info Box Display Time Set the display du
34. is a trademark of Telenor Conax AS e Dolby and the double D symbol are trademarks of Dolby Laboratories Warning HUMAX cannot be held responsible for any kind of problems caused by the use of unofficial software The use of software versions other than HUMAX official software will void the manufacturer s warranty It is advised that only the formal software released from HUMAX should be used in all HUMAX product range Caution To watch Pay Per View programmes be sure to inform your STB dealer of the STB s and Smart card s serial numbers So that they can pair your STB with your Smart card Otherwise you cannot watch the programmes because they are scrambled Note When the changed Network Information is sent Nagravision realizes that the appropriate satellite cable service information has been changed And it will re organize the service information based on the sent Network Information The message Network Information updated appears on the screen It is automatically done when changing NIT The manufacturer can t change it because it is provided by Nagravision When the user watches it the message may suddenly appear during AV playback and simultaneously updating will proceed This happens about once a year Since this is not an error in operating do not turn off the power e Information for TV Cabo subscriber When user searchs channels the channel numbers from 001 to 100 are defined automatically for
35. kal Bae E39 4 6 Conditional Access For Viaccess Embedded This menu allows the user to view the information on the Smart Card and Viaccess conditional access system such as general Smart Card Information Service List Change Maturity Rating and Change PIN code General Smart Card Information You can see the Unique Address so user Address Current Maturity Rating of the Smart Card Service List Services or Bouquets are encrypted by Viaccess and operators name like TPS or ABsat are displayed on the TV screen To get more detailed information of viewing rights of services or Bouquets press OK button Change Maturity Rating The STB is required by Viaccess to include a parental control facility for the viewing of restricted services This can be set to No block or for ages ranging from 4 to 18 The correct PIN code is required to change this option Change PIN code When you buy a new Smart Card the initial PIN code is set to NULL Therefore it is recommended that this PIN code should be changed This PIN code is available only on Conditional Access Menu Enter this PIN code to see the blocked Viacces Service e Specifications are for VA 5200 VACI 5300 models For CryptoWorks Embedded This menu allows the user to view and change information on the Smart Cards such as available entitlements Maturity Rating and PIN code Besides you can view the mails from programm providers General Smart Ca
36. lite Name only in the Antenna Setting menu Note In case the selected satellite is used as OTA target satellite automatic detection of the OTA target satellite might not work properly if you change or edit the name of the satellite 5 Satellite Name is listed in alohabetical order and the order can be changed according to Menu Language 6 When inputting the Satellite Name there is a 14 character limit LNB Frequency 1 Select the L O Frequency that is set to antenna 2 Use the lt gt buttons to select the LNB frequency Universal 5150 9750 10600 10750 11475MHz or 0 1 9 3 If the required LNB Frequency is not available then select 0 and enter the frequency manually using the NUMERIC buttons 0 9 4 When you select Universal both 9750 and 10600MHz are supported at the same time The 22KHz Tone setting is unnecessary Disabled 22KHz Tone When you use a dual LNB or two antennas connected to a 22KHz Tone switch box make 22KHz Tone switch enable or disable to select LNB or antenna 0 12Volt Switch When you use two LNBs or antennas is switched to 0 12V select what LNB and antenna are used enable or disable 0 12V terminal is located on the rear of STB DiSEgC Input According to the option and position of DiSEqC switch select Disabled Tone Burst Ato B and DiSEqC A to D After setting the above mentioned value press the OK button to move to the Manual Search menu Motorised System
37. move a service you want to change in the Service List Press the MENU 9 button Use the a v buttons to move to an item such as genre favourite lock skip delete you want on the Service Configuration screen 4 Use the lt buttons to select Press the OK button to complete w N E16 Guide of Main Menu Service All 1 To display the Service All press the OK button Use RED CD button to select the All service list 2 Select the desired service by using the 4 lt gt buttons 3 Press the OK button to view the selected service The service list provides you the Simple mode and Advanced mode The right side scroll bar of the screen displays the location of the selected service in relation to All services Press the RED CD button to toggle between Simple mode and Advanced mode Service Favourite 1 Press the GREEN C button on the remote control unit to select the Favourite service list Note The groups are labeled in four different alohabet characters A B C D 2 Use the a v buttons to select a favourite group that you want 3 Press the GREEN C button to toggle group and service list Service Network 1 Press the YELLOW D button on the remote control unit to select the Network service list 2 Use the a v lt gt buttons to select a service 3 Press the YELLOW button to toggle provider and service list Note 1 The provider name is displayed on the left window and the provider
38. n the HELP 2 button is pressed under Plate display and there are no detailed event informations in the I Plate the Help window will appear on the screen The Help window shows the current Network information including Satellite Name Frequency Polarisation Symbol Rate FEC The detailed information for the event can be displayed by pressing the HELP button in the I Plate with event data displaying mode Feed ta a ut i You can reserve the programme in the event data display mode by using the WHITE button You can reset timer programme Once Daily or Weekly mode When you release the timer programme mode then you will be asked to confirm the action ee me rs Ep E Changing Services To change services do in the following sequence 1 Press the NUMERIC buttons 0 9 on the remote control unit 2 Press the Ge buttons or buttons Or press the RECALL Gool Service list OK EPG mode button To switch between TV and Radio services press the TV Radio button To select the previous viewed Service press the RECALL Sei button E13 Volume Control To adjust the volume level use the GM buttons or lt gt buttons To temporarily stop the volume press the MUTE lt button To cancel mute press the MUTE lt button again or press the buttons or lt gt buttons Soundtrack
39. name Reset Resets all stored positions of the motor relative to the 0 position Installer mode only DiSEqC Command Mode Changes the current mode between Installer and User 2 Setting your Receiver for DiSEqC 1 2 You must set your receiver up so that it is ready to use DiSEqC 1 2 To do so do as follows 1 Press the MENU ed button to display the Main Menu 2 Select Service Searching option and press OK button to display the Service Searching menu 3 Select Antenna Setting option and press OK button to display the Antenna Setting menu 4 You must set up a separate antenna alternative for each satellite position required 5 Select the name of the satellite you wish to use 6 Select the correct LNB frequency for the LNB you are using 7 Set the Motorised System to Enable using the amp lt buttons 8 The option DiSEqC Input Selection should now be disabled This option is used for DiSEqC 1 0 and cannot be used in conjunction with DiSEqC 1 2 Your receiver is now ready to use DiSEqC 1 2 To return to the Main Menu use the EXIT button until you are at the Main Menu E42 Motorised System 3 Initial Satellite Position Search This is required when you first set your receiver up to use DiSEqC 1 2 and sets the positions of all pre programmed satellites 1 Make sure your motor is installed correctly with the calibrations adjusted for the region you are situated Please consult the user manual for your mo
40. o select the item you want to delete 3 Press the OK button to delete Press the EXIT button to cancel Le kie lal iar E30 Guide of Main Menu Fenr Meali ry Bme p rea ALT Hered DH ts Wb E CEET i LiF A heed dari ts E31 4 3 Service Searching Enter the PIN code to access the Service Searching menu as you access the Parental Control or Service Organising menu Press the OK button to start Service Search after setting the parameters The default PIN code is Antenna Setting Selects the antenna and LNB settings for Service search As you can change the settings for 22KHz Tone 0 12V and DiSEqC switch there are 32 possible Antenna Setting for use The values that are set in this menu will be available for selection in other service searching menus Antenna Alternative There are 32 antenna alternatives each one can have different combinations of settings for 22KHz Tone 0 12V and DiSEqC switch Satellite Name Selects the Satellite Name that corresponds to the value of the Antenna Alternative 1 Press the lt gt buttons to display the satellite list box 2 Select the wanted Satellite Name 3 If the desired Satellite Name is not listed then select User Defined 4 The keyboard will appear and you can type the Satellite Name directly The selected Satellite Name can help you select the Antenna Alternative in the searching menu but it is possible to change or select the Satel
41. on top of the STB Do not use any unrecommended attachments as these may cause hazard or damage the STB CONNECTION TO THE SATELLITE DISH LNB Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish FAILURE TO DO SO CAN DAMAGE THE LNB CONNECTION TO THE TV EARTHING LOCATION Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish FAILURE TO DO SO CAN DAMAGE THE TV The LNB cable MUST BE EARTHED The earthing system must comply with SABS 061 Place the STB indoor in order not to expose to lightening rain or sunlight N TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE RISK OF ELECTRIC SHOCK REFER SERVICING TO QUALIFIED SERVICE PERSONNEL DO NOT OPEN This symbol indicates dangerous voltage This symbol indicates inside the product that presents a risk of important instructions electric shock or personal injury accompanying the product Waringo Please do not insert metal or alien substance into the slots for the Modules and Smart Cards In doing so can cause damage to the STB and reduce its life span E2 Copyright Copyright e VIACCESS is a trademark of France Telecom e CryptoWorks TM is a trademark of Philips Electronics N V e Irdeto is a trademark of Mindport BV e Nagravision is a registered trademark of Kudelski S A e Conax
42. onnection to a digital amplifier 6 OOQ ES STB Connections There are several ways of connecting the STB to your existing Audio TV system We recommend using one of the following set up for best results QAR 2 mech D E E ee eem 8 o Z iF ON OFF Se SE GG j i NG E Sch Leen H TT zen EE si LNB OUT TV only 1 Connect one end of a 21 pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV 2 Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN connector on your TV 3 Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels 4 Connect the coaxial cable from the LNB to the LNB IN socket on the STB TV with VCR 1 Connect one end of a 21 pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV 2 Connect one end of a 21 pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR 3 Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN connector on your VCR 4 Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN connector on your TV 5 Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels 6 Connect the coaxial cable from the LNB to the LNB IN socket on the STB
43. ot E34 Guide of Main Menu Setzt Geach tito Pa bina Fi Bap Ais fn E35 Advanced Search Performs a manual search with the ability to enter PID Video Audio PCR values This mode is necessary when you search for the signal that has abnormal service Infornation tables The setting of the sub items is the same as Manual Search Video PID Audio PID PCR PID You can set PID to search for services 1 Use the lt gt buttons to select PID input mode 2 Use the NUMERIC buttons 0 9 on the remote control unit to enter a decimal PID value 3 In the hexadecimal input mode press one of the NUMERIC buttons 0 9 to display a hexadecimal keyboard 4 Enter a hexadecimal PID value Note If no PID is input Auto is displayed the Advanced Search functions same as Manual Search 5 After the above mentioned value is set press the OK button to start Service Search Note The picture and the found service list during Advanced Search are identical with the ones during Manual Search SMATV Search In case that several generations use Antenna and LNB in common as the frequency range of signal is input to STB is down as much as LNB L O Local Oscillator frequency search the service from 950 2150MHz Frequency Inputs not RF frequency but the frequency that is down converted through LNB in common The unit is MHz and the range of input is 950 2150MHz Symbol Rate Inputs the Symbol Rate of the signal you want to
44. ration of Information box displayed on the screen after changing services The time ranges from 0 to 20 seconds Menu Background Set the type of background for the menu to be displayed on Changing to Reserved Service When the reserved time has come during the view of services e Manual Mode This mode shows the message A reserved event has started on another service Press OK to view the reserved service Press EXIT to ignore reserved service will automatically change after 10 seconds And ask the presence of change and then makes a change e Auto Mode The current service will be automatically changed to the time reserved service Menu Mode Select NTSC PAL AUTO according to your TV type In AUTO mode the menu is automatically selected as NTSC or PAL according to the service played before the Menu mode is entered E25 Gp TY E LS LE fie i 4 2 Service Organising This menu gives users access to options that allow them to organise their TV Services Radio Services and Networks The default PIN code is l Organise TV Services Organise All Services This mode allows users to Delete Move Lock Skip and Rename TV Services e Delete 1 Press the RED CD button to delete unwanted services 2 Highlight the services that you want to delete in grey 3 Press the OK button to confirm 4 Press the EXIT button to cancel the deletion e Move 1 Press the GREEN button to move the service to where you
45. rd Information Card label will be displayed as issuer s name on the TV screen Programmes or Bouquets which are encrypted by only CryptoWorks TM and distributor labels displayed on the TV screen such as Wizja TV or MTV Europe and more To get more detailed information of viewing rights of channels or bouquets press the OK button e Smart Card details You can see smart card address the validity date and current maturity rating Tt brpai dezenn i d W H ee an pe HIR DEFT Ge d 988 Be teed da EE S oie Available Entitlements The user will select a single programme provider by selecting its distributor label and you can get the information of available entitlements e Subscription You can see the vaild period of each service e PPV Pay Per View If you purchased events in advance the entitlements of Pay Per View events will be displayed e IPPV Impulse Pay Per View You can purchase an event during the active broadcast of the event without pre ordering The entitlements of Impulse Pay Per View events will be displayed In this menu you need PIN code Maturity Rating The STB is required by CryptoWorks TM to include a parental control facility for the viewing of restricted programmes This can be set to Disable MR or PG Parental Guide to over 18 The correct PIN code is required to change this option PIN Code In this menu you can make PIN code enabled disabled or changed e Enable PIN code You can enable
46. rthermore you can recognize the states of hardware and software versions and signals from your STB 5 Utility This menu provides Calendar and Biorhythm E15 1 Select Service To select the desired in the service list you should firstly display the service list using OK button Use 4 lt gt buttons to select a service and press OK button Also use fie buttons to select a service directly in the service list The contents of service list are as follows Simple Service List 1 Use the 4 buttons to select Select Service from the Main Menu and press the OK button 2 Use the a v buttons to select Simple from the Main Menu and press the OK button 3 Then the simple service list will appear on the screen Advanced Service List The advanced service list shows twenty services This list is similar to the Simple service list except that it shows twenty services The full name of the service on the current cursor is displayed on the bottom of screen For Scrambled Service an icon appears on the right service Use the following colour buttons to list various service lists The colour button corresponds the following Service List e RED GD button service list All button Favourite button Network e BLUE button Genre button service list by Alphabetical order Service Configuration To change the attributes of a service 1 Use the a v lt gt buttons to
47. s point because the steerage signal occurs through the antenna cable 4 Loop Through If you have another analogue or digital STB and you wish to use the same LNB then you can connect it via the loop through Connect one end of a Coaxial cable to the LNB OUT on the STB and connect the other end to the LNB IN on your second STB GB5 5 Connect a S PDIF Fiber Optic cable If you are watching a programme with a Dolby Digital soundtrack see page E14 you can enjoy the higher quality sound of the Dolby Digital audio by connecting the STB to an external Dolby Digital television or amplifier Do this by connecting the optical S PDIF output of the STB to the optical S PDIF input of the external Dolby Digital product television amplifier 6 Software Upgrade HUMAX digital set top box is a highly sophisticated product incorporating one of the best software applications Whenever a problem is found with this software or in fact extra functions or enhanced applications are added the software in the equipment has to be upgraded In order to maintain proper performance of the product it is essential to have the most up to date software The latest news and release of software versions may be found at HUMAX website http www humaxdigital com It is recommended that users register to HCSA HUMAX Customer Service Area and periodically check for the availability of software upgrade There are three methods to upgrade the software
48. the PIN code e Disable PIN code You can disable the PIN code e Modify PIN code You can change the PIN code by using the NUMERIC buttons 0 9 on the RCU You will need to enter the old PIN code before you can enter new PIN code Mail box The STB can receive maximum 10 mails from programme providers To check and see the mails press the OK button In the Mail list you can view or delete the mails If you store 10 mails and a new mail arrives the oldest mail will be erased and the new mail will be stored e Specifications are for CRCI 5500 models E40 Guide of Main Menu Carrere eo PP kaf Pee P Feta men aT A a E41 For Nagravision Embedded This menu allows the user to view the information on the Smart card and Nagravision Conditional Access system such as version and serial number of Smart card PPV purchase list If you perchased events in advance the entitlements of Pay Per View events will be displayed ID event name service name Start time status and cost Credit information Displays the Credit information ID credit and status System information Displays the System information Smart card serial number IRD serial number Smart card version Smart card revision Conditional Access software version Conditional Access software revision e Specifications are for NACI 5700 models 5 Utility STB supports additional functions such as Calendar and Biorhythm At the Biorhythm
49. the item on the menus P P Programme up down buttons Press to tune to the next or previous service Press to move up or down pages on the menus HELP Press to display the help box on the screen EPG Electronic Programme Guide button displays the TV Radio programme guide RCL Recall Press to select the service that was previously viewed e Please note The design of Remote Control Unit may be changed without notice in advance E12 Guide of Functions Information Box I Plate The details of service part and event part are automatically L displayed on the l Plate when pressing the i button Ci or te r changing services e l Plate is divided into service part and event part SERVICE PART consists of the following items e Plate icon Current time and Dolby Digital symbol e Service name Service number icons e Subtitle Teletext Scrambling service symbol These are automatically displayed when the broadcasting station provides appropriate information e Signal level and Signal quality bar EVENT PART Right side of the box EVENT PART consists of the following items e Event name Event duration time e Description text of event State of reserved event Event Part shows the current and next event information gt button Use to move from the current event information to the next event information lt button Use to move from the next event information to the current event information Whe
50. this satellite 8 Automatic Search It is possible to use automatic search using the DiSEqC 1 2 motorised system 1 Ensure that the positions for the satellite you want to search is correct see Section 3 and 5 above 2 In the Main Menu select the option channel searching and press the OK button 3 In the Service Searching menu select the Antenna Alternative that you have set for this satellite 4 When you search new services please refer to Automatic Search of page E36 5 When the search has finished press the OK button to store and view the services Now that you have stored all the positions of the satellites and searched for all the services you want you can now use your receiver as normal When you change to a service that is being transmitted from a different satellite you will have to wait a few seconds to allow the motor to move into position to receive the new service Troubleshooting Guide Problem Solution About STB Does not display any message on the front panel or STB has no power Check the main power cable and check that it is plugged into a suitable power outlet Check you have switch the STB main power switch ON at the rear of the STB Check whether STB is in Standby mode No Picture Ensure that the STB is switched on see above Check the video output port SCART amp RCA Jack is firmly connected to the TV or VCR If you are using the RF Output check that the RF Lead is connected
51. tom of the submenu shows the signal level and the signal quality BER of the entered parameters Antenna Alternative Select the target antenna for Manual Search The Satellite Name helps you select Antenna Alternatives This is only for reference and cannot be changed on this menu Frequency Use the NUMERIC buttons 0 9 on the remote control unit Polarisation Use the lt gt buttons to select the Polarisation of the transponder Auto Horizontal Vertical e Horizontal 18 V is output through LNB line e Vertical 13 5 V is output through LNB line Symbol Rate Inputs the Symbol Rate of the transponder you want to find Use the lt gt buttons or Numeric buttons on the remote control unit FEC Forward Error Correction Use the lt gt buttons to select the Forward Error Correction of the transponder You can select the value of Auto 1 2 2 3 3 4 5 6 and 7 8 Network Search e You can select Yes or No When you select Yes you can find more transponders using the home network e As it refers to NIT during searching if there is the frequency information of other transponder it searches the other transponder besides the transponder that the user inputs Automatic Skip e You can select Yes or No When you select Yes the search will skip all scrambled services e When the found services are scrambled during searching they are not listed up Refer to descriptor of PMT whether it is scrambled or n
52. tor 2 Make sure your receiver is set up to use DiSEqC 1 2 see section 2 above 3 On the Main Menu select Service Searching option and press the OK button you should now see the Service Searching menu Highlight the option Antenna Alternative and press the OK button to display the Satellite Setting menu Highlight the DiSEqC Command Mode option and use the lt gt buttons to change the value to Installer and press the OK button Highlight the Motor Control option and use the lt gt buttons to change the value to reset and press the OK button You will now see a warning message press the OK button to continue All motor positions of the pre programmed satellites should now be correct If you have any other make or model of DiSEqC 1 2 motor then you may need to store the satellite positions in yourself Please refer to the user manual for your motor Highlight the DiSEqC Command Mode option and use the lt gt buttons to change the value to User and press the OK button 9 You should now be ready to start storing services for the various satellites see 5 onwards E jo N CO 4 Motor Limit Setting Use this option to set the East and West limits of the motor This should be used to prevent your dish from hitting anything that may be obstructing the path of the dish 1 On the Main menu select Service Searching option and press the OK button You should now see the Service Searching menu 2 Select Manu
53. use the 4 v lt gt buttons to adjust your birth year and date to see your current biorhythm status Motorised System DiSEqC 1 2 User Instructions lf you have a DiSEqC 1 2 motorised system then you can use the DiSEqC 1 2 functions available The following instruction describes how to use the DiSEqC 1 2 functions to store the positions of the satellites and to search for the services STAB Rotor Sat motor recommended 1 Satellite Setting Menu Options When DiSEqC Motorised System is Enabled in the Antenna Setting a new menu is available for configuring the motor This menu is called Satellite Setting and is accessed by pressing the OK button while the option Antenna Alternative is highlighted in the Manual Search menu The following options are available on the Satellite Setting menu Satellite Name A selection of satellite names that can be used to identify a motor position If the satellite name you require is not available please use other In installer mode the Satellite Name Reference refers to the 0 position of the motor Movement In user mode this is used to fine tune the position of the motor for better reception In Installer mode this is used to search for the position of a satellite manually Motor Control Search Searches for services on the chosen transponder Goto Moves the motor to the stored position of the selected satellite name Store Stores the current position of the motor for the selected satellite
54. usly memorised Audio Language If the Audio Language of current service is not provided at this time you should reselect a language on the Audio Language menu Languages provided Czech Danish Dutch English Finnish French German Greek Hungarian Italian Norwegian Portuguese Rumanian Russian Spanish Swedish Turkish and more If no language is provided then the default language of current service will be automatically selected Subtitle Language Select the default language for subtitle when changing services Language provided Danish English Finnish French German Greek Hungarian Italian Norwegian Portuguese Spanish Swedish and more E22 Guide of Main Menu Time Setting You can set the Current Time and Wakeup Time in this mode Furthermore the Service Number in the Wakeup mode and Sleep Time standby mode can be set When a VCR is connected recording can be automatically done according to Wakeup Sleep Time Setting Tire Se Gey Current Time To set the Current Time enter the Offset value using the standardised information of current service area The time setting will be used as the standardised time for the l Plate TV Guide Wakeup and Sleep Timer Time Offset Current Time is based on TDT Time and Data Table at the stream of the current service Timer You can select nine kinds of Timer like 1 2 8 and Disabled If you select Disabled then the other timers will not work

Guide of Main Menu - Pdfstream.manualsonline.com

Contents

Download Pdf Manuals

Related Search

Related Contents