LED Bar™ - Lightsounds
Contents
1. 17 TECHNICAL SPECIFICATIONS ta aree t cc rea pe Qr 18 LED Bar User Manual 2 2007 10 19 14 56 1 BEFORE YOU BEGIN What is included 1 x LED Bar 2 Tall Mounting Brackets 2 Short Mounting Brackets Power Cord Warranty Card User Manual Unpacking Instructions VVVVVV Immediately upon receiving a fixture carefully unpack the carton check the contents to ensure that all parts are present and have been received in good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing AC Power This fixture has an auto switching power supply that can accommodate a wide range of input voltages The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages This fixture will accommodate between 100V and 240V AC All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch To determine the power requirements for a particular fixture see the label affixed t2. 2 Connect the end of the cable coming from the controller which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector 431104109 09 This drawing provides general illustration of the DMX Input Output panel of a lighting fixture 3 Then proceed to connect from the output as stated above to the input of the following fixture and so on CHAUVET Certified DMX Data Cables Order Code Description DMX1 5 DMX Cable 1 5m 4 9ft DMX4 5 DMX Cable 4 5m 14 8ft DMX10 DMX Cable 10m 32 8ft Master Slave Fixture Linking pecunie 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the first fixture 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector Then Often the setup for Master Slave proceed to connect from the output as stated above to the input of the following fixture and so on and Standalone operation requires that the first fixture in the chain be initialized for this purpose via either settings in the control panel or DIP switches Secondarily the fixtures that follow may also require a slave setting Please consult the Operating Instructions section in this manual for complete instructions for this type of setup and config
3. Color Fade Mode CH DESCRIPTION DMX 220 255 1 Color Fade and Auto Run 2 Run Fade Speed gt No Function 4 Function For a detailed view of DMX values turn to the DMX Channel Values on page 16 in the Appendix section LED Bar User Manual 5 2007 10 19 14 56 Product Overview LEDs Control Panel rear See exploded view below Mounting Brackets Footcontroller Input Optional Accessory LED FS1 Power Output IEC Power For LED Bar Connector with only max 20 Fuse Holder DMX Out Microphone Control Panel Master Slave Sound Output Sensitivity Adjustment LED Bar User Manual 6 2007 10 19 14 56 3 Disconnect the power cord before replacing a fuse and always replace with the same type fuse Fuse Replacement With a flat head screwdriver wedge the fuse The fuse is located holder out of its housing Remove the damaged inside this fuse from its holder and replace with exact compartment same type fuse Insert the fuse holder back in Remove using a flat head screwdriver its place and reconnect power Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX 512 controller or to run synchronized shows on two or more fixtures set to a master slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link
4. Color fade P Run speed LED Bar User Manual 11 2007 10 19 14 56 DMX Control Mode Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to customizing or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently DAISY CHAIN CONNECTION 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the first fixture 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector Then proceed to connect from the output as stated above to the input of the following fixture and so on 10 1 09 09 5 7 CE SSS ooeO You can use the Master Slave link to control multiple units as one DMX device Read the instructions on the following page OO Oo B LH ooeO DMX MODE SETUP 1 Press the Mode button until the dispplay reads SyS then press Enter Press the Up and Down buttons until the display reads S dAd then press Enter Set the DMX address value by using the Up and Down buttons Press the Mode button use the Up Down until the display reads S Aad Press Enter to make changes permanent Press the Up Down buttons to
5. consultation If you sell the unit to another user be sure that they also receive this instruction booklet Always make sure that you connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture Make sure there flammable materials close to the unit while operating The unit must installed a location with adequate ventilation at least 20in 50cm adjacent surfaces Be sure that no ventilation slots are blocked Always disconnect from power source before servicing or replacing lamp or fuse and be sure to replace with same lamp source Secure fixture to fastening device using a safety chain Never carry the fixture solely by its head Use its carrying handles Maximum ambient temperature is 95 F 35 C Do not operate fixture at temperatures higher than this In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to a dimmer pack Make sure the power cord is never crimped damaged Ne
6. Bar WARRANTY INFORMATION 2 year limited warranty Snapshot OK on Dimmer Outdoor OK Sound Activated DMX512 Master Slave 115V 230V Switch Replaceable Fuse User Serviceable LED Bar User Manual 18 2007 10 19 14 56
7. D Bar User Manual 17 2007 10 19 14 56 Technical Specifications WEIGHT amp DIMENSIONS 38 965 ets 2 5 in 64 6 in 152 mm 4 5 16 9 1 kgs POWER Auto switching power 100 240V 50 60Hz Power Consumption 33 3W 39A max at 120V Inrush Power sis 24 6W 33A at 120V Power Factor 70 at 120V Power Output AG Plug 8A 960W at 120V LIGHT SOURCE M 384 Total 128 red 128 green 128 blue 100 000 hour PHOTO OPTIC Beam Angle zi enorm pae ba iota deitas cav ac dene 63 x 29 82 52 THERMAL Maximum ambient 10432 40 C FUSE 1 5A 250V fast blow CONTROL amp PROGRAMMING PiCEJes M locking 3 pin XLR male socket Data output MIO locking 3 pin XLR female socket Data pin configuration pin 1 shield pin 2 pin 3 Cr E DMX 512 USITT DMX m M 4 ORDERING INFORMATION DED Bat ETE LED
8. LED Bar USER MANUAL LED Baf uec EPI 1 BEFORE YOU BEGIN ncc couvrent caet aat c a n d b S D n a i RE 3 WHATS INCLUDED a ne caus Pa b nt i a E n a Cl e D n d 3 NPACKINGINSTRU CTIONS 4 55 err vcr rnc er n e man m nr er een cenar cr e orc eh CE Y P EE RE 3 AC POWER a a 3 CONTAC THUS aenea uA 3 SAFETY INSTRUCTIONS 4 2 INTRODUCTIO nasi ciu s cn t ar cm cr t a nc ain iA a Re aA 5 FEATURES RR RR OE ER ER C bb n CURE P ER RA a RE NRG 5 DMX CHANNELS UMMARY en en Pe Pa ete er Or rd 5 PRODUCT OVERVIEW tons irrita cnc a on d te c Dr Co pn Xd a E Red n nian Eh D E CE 6 3 5 e P 7 FUSEREPEACEMENTS contiennent rac tesa see nte rU EDGTUREPEINKINGR Data Cabling sene ei DMX Data Cabl8 tree ar te eder arcet crean teinte er n lc nb n BI e RA e Y Cd Cable Connectors 3 Pini to 5 Pin Conversion oi acc in attri a coc n ar cm a Coma ac rm uu n bcn o P d 8 SETTING UP DMX SERIAL DATA nene tnnt rennen reiten reiten nt 9 MASTER SEAVE FIXTURE LINKING reci n iren nm rec e D d Cl C D d Ea 9 MOUNTING Sa orari a de eran dts c s
9. X Primer There are 512 channels in a DMX 512 connection Channels may be assigned in any manner A fixture capable of receiving DMX 512 will require one or a number of sequential channels The user must assign a starting address on the fixture that indicates the first channel reserved in the controller There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required Choosing a start address should be planned in advance Channels should never overlap If they do this will result in erratic operation of the fixtures whose starting address is set incorrectly You can however control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation In other words the fixtures will be slaved together and all respond exactly the same fixtures are designed to receive data through a serial Daisy Chain A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture Use an order that provides for the easiest and most direct cabling Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors The shield connection is pin 1 while pin 2 is Data Negative S and pin 3 is Data positive S CHAUVET carrie
10. anges 080 lt gt 089 Colorchange 1 090 lt gt 099 1 change 2 100 gt 109 Color change 3 110 amp 119 Color change 4 R 1 120 amp 129 Colorchange 5 130 gt 139 Color change 6 Automatic Sequential Color Chases 000 lt 127 140 gt 149 1 Sound Active 150 159 Colorchase2 128 lt gt 255 160 lt 169 Color chase 3 170 gt 179 Colorchase4 180 gt 189 Colorchase 5 190 lt 199 Colorchase 6 200 lt 209 Colorchase 7 RGB Color Mix Red 210 amp 219 RGB mode 0 100 Fade Speed 220 lt 229 ColorFade 0 100 230 gt 255 Auto Run sound active only LED Bar User Manual Flash Speed 000 lt gt 249 Sound Active 250 gt 255 Green Blue 0 100 0 100 2007 10 19 14 56 General Troubleshooting Applies to Symptom Solution s Lights feces Controllers es Auto shut off Check fan thermal switch reset Beam is very dim or Clean optical system or replace lamp not bright v Check 220 110v switch for proper setting Breaker Fuse keeps Check total load placed on device blowing Chase is too slow Check users manual for speed adjustment v Y Device has no power Check for power on Mains 5 y 2 Check device s fuse internal and or external Fixture is not Check DMX Dip switch settings for correct addressing responding Check DMX cables Y Check polarity switch settings Fixture is on but there Make sur
11. can support Important Fixtures on a serial data link must be daisy chained in one single line To comply with the EIA 485 standard no more than 32 devices should be connected on one data link Connecting more than 32 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal Maximum recommended serial data link distance 500 meters 1640 ft Maximum recommended number of fixtures on a serial data link 32 fixtures Data Cabling To link fixtures together you must obtain data cables You can purchase Light Emotion certified DMX cables directly from a dealer distributor or construct your own cable If you choose to create your own cable please use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference LED Bar User Manual 7 2007 10 19 14 56 DMX DATA CABLE Use a BeldenO 9841 or equivalent cable which meets the specifications for EIA RS 485 applications Standard microphone cables cannot transmit DMX data reliably over long distances The cable will have the following characteristics 2 conductor twisted pair plus a shield Maximum capacitance between conductors 30 pF ft Maximum capacitance between conductor and shield 55 pF tt Maximum resistance of 20 ohms 1000 ft Nominal impedance 100 140 ohms CABLE CONNECTORS Cabling must have a male XLR connector on one end and a female XLR connect
12. e you have the correct audio mode on the is no movement to the control switches If audio provided via jack make sure audio a live audio signal exists Adjust sound sensitivity knob Lamps cuts off Possible bad lamp or fixture is overheating 2 Lamp may at end of its life Light will not come Some discharge lamps require a cooling off period before after power failure the electronics in the fixture can kick start it again wait 5 v to 10 minutes before powering up Loss of signal Use only DMX cables Install terminator Y v Note Keep DMX cables separated from power cables black lights No flash Re install bulb may have shifted in shipping No laser output Bounce mirror motor may have shifted during shipping v readjust Relay will not work Check reset switch 2 Check cable connections Remote does not work Make sure connector is firmly connected to device v Y Stand alone mode All Light Emotion lighting fixtures featuring stand alone functions do not require additional settings simply power v the fixture and it will automatically enter into this mode If you still have a problem after trying the above solutions please contact LSW Technical Support at the location on the next page LED Bar User Manual 2007 10 19 14 56 Technical Support Address Service Dept Support Email Telephone 02 97875905 Fax Website http www industrygear com 5 APPENDIX DM
13. ed in series Master Slave Link MASTER UNIT Settings Press the Mode button repeatedly until the display reads Act then press the Enter button ct programs 001 023 by using the Up and Down buttons Some programs have additional controls such as flash and run speed Press the Mode button to toggle additional functions then use the Up and Down buttons to change values 3 Pin XLR DMX cable DMX signal output does not continue on M S linked fixtures Refer to the Control Panel Modes amp Functions chart on the previous page SLAVE UNIT Settings Units that follow the Master unit will automatically synchronize to the Master unit No other settings are required IMPORTANT INSTRUCTIONS FOR MASTER SLAVE OPERATION Turn ON the Master unit last This will assure that the master unit will fully detect all linked units and re configure its built in sequential chase programs to run on the correct number of linked units Built in programs detailed PROGRAM FUNCTION OPTIONS 000 Blackout 001 007 Solid flashing colors F Flash speed 008 013 Color chase programs P Run speed F Flash speed 014 020 Sequential color chase patterns sound sensitivity rotary knob to adjust sound level for optimum response or decrease sensitivity completely to operate in Run speed only P Run speed 021 RGB manual color mix P Red F Green C Blue 022
14. enu which will reset the unit LED Bar or COLORbank LED ONLY Controlling multiple LED Bars as one device 1 Turn on all Fixtures On the first fixture press the Mode button until the display reads SyS then press Enter Press the Up and Down buttons until the display reads S dAd then press Enter Set the DMX address value by using the Up and Down buttons Press the Mode button use the Up Down until the display reads S Aad Press Enter to make changes permanent and re initialize the fixture so that all following fixtures in the down link can be counted and the sequential color chases will run correctly 6 Press the Up Down buttons to return to the DMX control state the display will read S dAd LED Bar User Manual 13 2007 10 19 14 56 DMX Channel Values NOTE Please read all instructions carefully on fixture DMX control mode and addressing DMX channels 2 3 and 4 functions are determined by the current settings of channel 1 For example while Channel 1 is set between 210 and 219 the following conditions will apply Channel 2 will control the Red LEDs Channel 3 will control the Green LEDs Channel 4 will control the Blue LEDs CHANNEL VALUE FUNCTION Static Colors 000 lt gt 009 Blackout 010 gt 019 Red 020 gt 029 Green 030 lt gt 039 Blue 040 gt 049 Yellow 050 amp 059 Purple 060 lt gt 069 070 lt 079 White Color Ch
15. m rv e tigi PIT TU IET TTL MINNIE 9 cana cina CH TE CEA EA da CHER P EUR P ERE v EPA Do CE REM e EE Da 9 00110255 AU ET eR E HERD EORR Tee D GERNE PT ARNT 9 4 OPERATING INSTRUCTIONS sissi 10 10 Control Panel Modes amp F unctions c icc ecc tete de ie ed dan 10 MASTERISEAVESR S TAND A LONE eie 11 MASTERS LEAVES STAND ALONE iniitisvaca nim e br e cn e v e aa 11 Built in programs detailed R 11 DMX CONTROL MODE 12 Daisy Chain Connect sssaaa aai a 12 DMX Mode sandal AEE EN A E AN 12 About DMX addressing RODA HORNO Uere LIN bo HERO NN o 13 CONTROLLING MULTIPLE LED Bars AS ONE neret reet reet rin 13 CHANNEL 14 GENERAL TROUBLESHOOTING tim ncc cni end i ne n ed n E C GR a E E P RO E e Pr EU 15 uc ire pra t gf t ccn n a tae a E ERE 16 Bi a sc EE at on ce Fn hu ER a E ERR RD 16 DMXSPRIMERA et ie ettet treu ue estt enc cee AD ce 16 GENERAL MAINTENANCE rt T d i cn Dr C v Dc a d l d i n c ER E P P 17 RETURNS PROCEDURE sierra rei tir pe re n e e d A e a pr RE PR e P CE ed 17
16. o the back plate of the fixture or refer to the fixture s specifications chart A fixture s listed current rating is its average current draw under normal conditions All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch Before applying power to a fixture check that the source voltage matches the fixture s requirement Check the fixture or device carefully to make sure that if a voltage selection switch exists that it is set to the correct line Figure 1 AC Voltage Switch voltage you will use Warning Verify that the voltage select switch on your unit matches the line voltage applied Damage to your fixture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch All fixtures must be connected to circuits with a suitable Earth Ground Contact Us Not all fixtures have a voltage select switch Please be sure to connect to the proper voltage General Information Technical Support LSW Service Department 81 Gould St Campsie NSW 2194 World Wide Web www industrygear com LED Bar User Manual 3 2007 10 19 14 56 Safety Instructions Please read these instructions carefully as it includes important information about the installation usage and maintenance of this product Please keep this User Guide for future
17. or on the other end Resistance 120 ohm 1 4w between pin 2 DMX and pin 3 DMX of the last fixture DMX connector configuration 91 COMMON e 22 2232 3 OUTPUT 20207 Termination reduces signal errors avoid signal transmission problems and interference it is always advisable to connect a DMX signal terminator CAUTION Do not allow contact between the common and the fixture s chassis ground Grounding the common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other 3 PIN TO 5 PIN CONVERSION CHART Note If you use a controller with a 5 pin DMX output connector you will need to use a 5 pin to 3 pin adapter Light Emotion Model No DMX5M or DMX5F The chart below details a proper cable conversion 3 PIN TO 5 PIN CONVERSION CHART Conductor 3 Pin Female output 5 Pin Male Input Ground Shield Pin 1 Pin 1 Data signal Pin 2 Pin 2 Data signal Pin Pin 3 Do not use Do not use Do not use Do not use LED Bar User Manual 8 2007 10 19 14 56 Setting up a DMX Serial Data Link 1 Connect the male 3 pin connector side of Universal DMX Controller the DMX cable to the output female 3 pin connector of the controller e
18. ress ENTER to enter the sub menus Control Panel Modes amp Functions FUNC PROGRAM FUNCTION PROGRAM P RUN SPEED FLASH SPEED C COLOR 000 Blackout 001 Red 000 100 002 Green 000 100 003 Blue 000 100 004 Yellow 000 100 005 Purple 000 100 006 Cyan 000 100 007 White 000 100 008 Color Change 1 000 100 009 Color Change 2 000 100 010 Color Change 3 000 100 011 Color Change 4 000 100 Ct 000 012 Color Change 5 Automatic 013 Color Change 6 000 050 014 Sequential Color Chase 1 015 Sequential Color Chase 2 Sound Active 016 Sequential Color Chase 3 051 100 017 Sequential Color Chase 4 018 Sequential Color Chase 5 019 Sequential Color Chase 6 020 Sequential Color Chase 7 021 RGB Red 000 100 Green 000 100 Blue 000 100 022 Color Fade 000 100 023 Automatic Program Sound S dAd DMX Channel Addressing Re initialize fixture SYS Pad Re establishes correct number of down link fixtures for sequential color chase runs LED Bar User Manual 10 2007 10 19 14 56 Master Slave amp Stand Alone The Master Slave mode will allow you to link units in a daisy chain fashion In this mode the first unit in the daisy chain will command all other units following Stand Alone can simply be achieved by setting all units to Master They would no longer be required to be link
19. return to the DMX control state the display will read dAd 6 Repeat this for every fixture you wish to address LED Bar User Manual 12 2007 10 19 14 56 About DMX addressing This DMX mode enables the use of a universal DMX controller device Each fixture requires a start address from 1 to 511 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 6 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 and 105 Choose starting addresses so that the channels used do not overlap and notate the start address selected for future reference If this is your first time addressing a fixture using the DMX 512 control protocol than we suggest jumping to the Appendix Section and read the heading DMX Primer It contains very useful information that will help you understand its use 0 Master Slave Output 0 24371031105 0 LH OO EH 9 3 Pin XLR DMX Fixture DMX cable DMX CIH OO o TO Q Fixture If Master Slave or linked units do not appear to correctly run sequential color chases simply turn the first fixture OFF then To other DMX back ON or select S Aad in the To other fixtures m
20. ry 20 days Clean the internal optics at least every 30 60 days Returns Procedure Claims Returned merchandise must be sent prepaid and in the original packing call tags will not be issued Package must be clearly labeled with a Return Merchandise Authorization Number RA Products returned without an RA will be refused Call LSW and request RA prior to shipping the fixture Be prepared to provide the model number serial number and a brief description of the cause for the return Be sure to properly pack fixture any shipping damage resulting from inadequate packaging is the customer s responsibility LSW reserves the right to use its own discretion to repair or replace product s As a suggestion proper UPS packing or double boxing is always a safe method to use Note If you are given an RA please include the following information on a piece of paper inside the box 1 Your name 2 Your address 3 Your phone number 4 The RA 5 brief description of the symptoms Damage incurred in shipping is the responsibility of the shipper therefore the damage must be reported to the carrier upon receipt of merchandise It is the customer s responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping Any other claim for items such as missing component part damage not related to shipping and concealed damage must be made within seven 7 days of receiving merchandise LE
21. s 3 pin XLR DMX compliant cables DMX 10 33 DMX 4 5 15 and DMX 1 5 5 LED Bar User Manual 16 2007 10 19 14 56 General Maintenance To maintain optimum performance and minimize wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output performance and can cause overheating This can lead to reduced lamp life and increased mechanical wear Be sure to power off fixture before conducting maintenance Unplug fixture from power Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surfaces until they are free of haze and lint The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least eve
22. uration Mounting ORIENTATION This fixture may be mounted in any position provided there is adequate room for ventilation RIGGING Hanging Clamp It is important never to obstruct the fan or vents pathway Mount the fixture using a suitable C or O type clamp Adjust the angle of the fixture by loosening both knobs and tilting the fixture After finding the desired position retighten both knobs e When selecting installation location take into consideration lamp replacement access and routine maintenance Safety cables must always be used e Never mount in places where the fixture will be exposed to rain high Note humidity extreme temperature changes or restricted ventilation Clamp is sold separately LED Bar User Manual 9 2007 10 19 14 56 4 OPERATING INSTRUCTIONS The LED Bar is a DMX 512 controllable full RGB color mixing LED strip light fixture made up of highly efficient and super bright LEDs There are four flood spot led surfaces whose intensity can be controlled together allowing the creation of an unlimited range of colors The LED Bar can operate in Stand Alone Master Slave and via DMX 512 control utilizing 4 channels of control Using the control panel 1 Press the MODE button repeatedly until the display reads the mode function you wish to change 2 Press the DOWN or UP buttons to toggle or scroll through values that pertain to that function 3 P
23. ver disconnect the power cord by pulling or tugging the cord e X Avoid direct eye exposure to the light source while it is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact LSW at 97875905 LED Bar User Manual 4 2007 10 19 14 56 2 INTRODUCTION Features e 4 channel DMX 512 LED cyclorama light Blackout static dimmer strobe e Operating modes Blackout and static flashing colors RGB color mixing Color fade e Static colors and RGB color mixing with or without DMX controller Built in automated programs master slave or DMX Built in sound active programs master slave or DMX Additional Features e Linkable with COLORbank LED Additional power output for daisy chaining units together e Master slave mode with additional output for daisy chaining Allows for color changing runway effect up to 31 units e Sound sensitivity knob e Low power consumption Optional Controller LED Bar Foot Controller LED FS1 DMX Channel Summary Blackout and Chase Programs RGB Mode Static Flashing colors CH DESCRIPTION CH DESCRIPTION CH DESCRIPTION 4 DMX 000 079 4 DMX 080 209 4 DMX 210 219 Static Colors Programs 1 13 RGB Color Mix 2 Function 2 RunSpeed 2 Red Flash Speed Flash Speed Green 4 No Function 4 Blue
Download Pdf Manuals
Related Search