Kollector Elite Network Digital Video Recorder
Contents
1. Cable Types The most commonly used cable types are dual individually shielded twisted pair in a single jacket This configuration is the most convenient for RS 422 RS485 applications Single twisted pair is also a suitable cable Choose a Belden cable type by referring to the characteristics and maximum distances listed below The maximum distance for the most reliable digital control refers to the distance between the CPU Keypad and the Camera Dome Assembly The characteristics of the cables in Table 6 should be used as a guideline when cables other than Belden are used Materials and construction must follow the guidelines above Table 9 1 Recommended Individually Shielded Twisted Pair Cable Types Cable Type Wire Size Insulation Jacket Max Distance ft m Number of AWG Material Material Twisted Pairs Belden 9406 22 PVC PVC 5000 1500 2 Belden 9402 20 PVC PVC 5000 1500 2 Belden 8723 22 Polypropylene PVC 8000 2400 2 Belden 8162 24 Datalene PVC 15000 4600 2 Belden 9729 24 Datalene PVC 15000 4600 2 Belden 9182 22 Datalene PVC 25000 7600 1 1 Datalene is a Registered Trademark of Belden 20 e Twisted Pair Cable Recommendations XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 10 Technical Information Table 10 1 Technical Information Electrical Characteristics Input Voltage Current Power Consumption UPS Requirements Heat Equivalent System Connector Types Quantitie2. TX or RX and RX depending on the type of the camera refer to Figure 3 3 on page 10 Ensure that you connect the wires to the correct polarity 3 Install the other end of this cable into the device it will communicate with for example a V1400X IDL Camera Dome or other type of receiver 4 Connectthe RJ45 cable to the appropriate channel in the rear panel Sensor Input When using SMSR connectors to connect devices to the Kollector Elite refer to the guidelines described below according to the specific device type NOTE Speaker SPK will be operational in future versions To connect a sensor to the Kollector Elite 1 Using a twisted pair cable as defined in Chapter 9 Twisted Pair Cable Recommendations prepare a 2 conductor type cable by stripping the ends back for use XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Installation e 9 2 Connectthe sensor wires to the SENS and GND connectors refer to Figure 3 3 below 3 Install the other end of this cable into the appropriate sensor output NO or NC dry contact 4 Connect the RJ45 cable to the appropriate channel in the rear panel refer to Figure 3 2 on page 6 RJ45 Cable Termination Box Figure 3 3 Termination Box 5 When using a detector that operates with a resistor the resistor should be connected as follows e Normally Open Detector The resistor should be connected to the sensor SENS and the ground GND connectors e Normally C
3. contains necessary items needed to install and wire the recorder during installation as follows Table 1 1 Accessory Kit Part Description Quantity Front Door Key Opens the front panel door 2 Installation and Operation Manual 3 i i A 9 4 1 Provides instructions on installation configuration and operation Software Manual 1 RJ45 Cable Assemblies Connects external devices sensor input and communication signals 16 Termination Boxes RS 422 PTZ control 16 Video Adapter Cable certain Used to adapt the video card ports for various monitors 1 models Optical Mouse Used for GUI operation of the ViconNet software 1 Provides additional video looping outputs from each camera for use Looping Cable with other video components Power Cord Used for power connection of Kollector Elite 1 Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory It is the carrier s responsibility to provide suitable delivery Inspect the cartons upon delivery and if damage is present make detailed notes on the carrier s bill Then obtain the carrier agent s signature and file a damage claim as soon as possible Open the cartons and inspect the equipment for damage Save the cartons and packing material If damage is present contact the carrier and file a damage claim immediately If the equipment must be returned for repair follow the instructions in Chapter 7 Shipping Instructions 2 e Introduction X
4. meets requirements for an FCC Class A computing device Vicon requires the use of line conditioners voltage regulators and uninterruptible power supply UPS systems in the electrical power service NOTE Read all instructions before beginning the installation How to Use This Manual This manual was designed to provide the best overall instructions for the installation and operation of the Kollector Elite Digital Video Recorder The graphics and terminology used in this manual have been carefully selected to enable a clear and distinct understanding of the Kollector Elite and its configuration This manual has been formatted to present distinct methods of installation for experienced strong computer background and novice installers For Experienced Installers Refer to Chapter 2 Quick Installation on page 3 Figure 2 1 presents the most common installation for all ports and connectors of the Kollector Elite For more detailed descriptions refer to Chapter 3 Installation and Chapter 4 Operation XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Introduction e 1 For Novice Installers Complete the remainder of this chapter and then proceed to Chapter 3 Installation When complete proceed to Chapter 4 Operation to power on and boot the system For software information refer to the Kollector Elite Software Manual XX112 3X where X is a revision number between 0 and 9 Accessory Kit The provided accessory kit
5. the unit Before beginning the hardware installation ensure that the following environmental conditions have been met e The surface on which the ViconNet hardware is to be placed must be level e The room or area designated for the ViconNet hardware installation must be well ventilated Step 1 Connecting the Hardware This procedure describes the various hardware connections that must be performed in order to operate the system To connect the ViconNet hardware 1 Perform the following connections refer to Figure 3 1 on page 5 and Figure 3 2 on page 6 e Locate the keyboard on a flat surface near the recorder Connect the keyboard by inserting its connector into the correct port e Locate the mouse on a flat surface near the recorder Connect the mouse by inserting its connector into the correct port e Position the monitor in a permanent fixed location near the recorder Connect the monitor by inserting its VGA connector into the VGA Monitor Output port e Insert one side of a standard LAN cable to the Network Port s RJ 45 connector Insert the other RJ 45 connector into the LAN side of the network e Gather and locate all camera video input cables near the rear of the recorder Insert each BNC M into its respective Video Camera Input port 1 16 e Mount the provided Termination Boxes in a fixed permanent location near the recorder Insert one end of the provided RJ 45 Cable Assembly into the Termination Box and inse
6. ON position I pressed in If the recorder fails to boot call Vicon Technical Support e f the recorder boots but does not display the Main Screen reboot the unit by toggling the front panel power switch OFF and ON If the recorder still fails to boot call Vicon Technical Support 14 e Troubleshooting XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 6 Maintenance Periodic checking and maintenance of certain parts of your Kollector Elite will minimize future system problems The following table lists the items that need to be checked and when Maintenance Required Monthly Annually Replacing the filter Cleaning the filter Backing up Checking the front and rear fans To replace the filter 1 Turn the Kollector Elite off and then open the front door 2 Open the filter housing on the left hand side 3 Carefully remove the old filter and then replace it with a new 105mm x 175mm filter 4 Close the filter housing 5 Turn the Kollector Elite back on and then close the front door To clean the filter 1 Turn the Kollector Elite off and then open the front door 2 Open the filter housing on the left hand side 3 Carefully remove the old filter and then wash it under running water with a mild soap 4 When the filter is completely dry return it to its place in the Kollector Elite 5 Close the filter housing 6 Turn the Kollector Elite back on and then close the front door To
7. SEE RERRRRRKSERMRERIRERRR RE RENE ERAS eke dia Powering Off the Recorder ei ESE EER alari Powering On the Recorder EE ini 13 CHAPTER 5 TROUBLESHOOTING tette EE EE EE XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Table of Contents e iii CHAPTER 6 MAINTENANCE a CHAPTER 7 SHIPPING INSTRUCTIONS esse sesse ee esse sesse ee ee ee ee ee EE EE Ee ee einen CHAPTER 8 COAXIAL CABLE RECOMMENDATIONS esse sesse ee ee ee ee ea EER RR Re ee ee MaterialS SR temia dia Cable EE EE EE OR RE ON CHAPTER 9 TWISTED PAIR CABLE RECOMMENDATIONS gt ELLEN AE EE NE EE Cable EE ER EE EE ER EE ER OR RE EE EEN CHAPTER 10 TECHNICAL INFORMATION esse esse ee ees sees ee ee ee RR RR RR EER Ee nnne nennen 21 List of Figures Figure 2 1 Kollector Elite Quick Installation ii Figure 3 1 Front Panel Layout EE EE EE ED Figure 3 2 Rear Panel Layout i detener dire cedent bebe bedek ed bee des aio cura Pra eds ER ae be eue gee ng Figure 3 3 Termination BOX nennen nene nnne nenne esten ee Ge ee ee Re ee nennen nnns Figure 3 4 Resistor Connection TypeS eene enne enn ee nennen nnns enr rne nnns Figure 3 5 Looping Cable ii Figure 10 1 Kollector Elite Dimensions nennen nennen nnne enn List of Tables Table 1 1 Accessory Kil ii
8. Type Connector Figure 3 5 Looping Cable XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Installation e 11 Step 4 Connecting the Power Supply To ensure that the Kollector Elite is protected during a power failure and that no important data is lost it must be connected to an uninterruptible power source UPS before use To connect the UPS 1 Connectthe Kollector Elite s power cord to the UPS power receptacle 2 Connect the UPS power cord to the wall outlet 3 Power on the UPS and ensure that it is working properly 4 Poweron the Kollector Elite NOTE Refer to your UPS device s User Manual for a more detailed explanation of how to connect it properly 12 e Installation XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 4 Operation About This Chapter This chapter details power on booting and power off of the Kollector Elite Digital Video Recorder For full programming and operation information refer to the Kollector Elite Software manual XX112 3X where X is a revision number between 0 and 9 The following sections provide information as follows e Powering on the Recorder guides the user through proper power on and boot procedures e Powering off the Recorder guides the user through proper shut down procedures Powering On the Recorder To power on the system 1 With the recorder set up as shown in Chapter 3 Installation verify that the rear panel toggle switch
9. X112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 2 Quick Installation TO MONITORS Camera VGA Display Monitor VN5000 WORK STATION bo A Video Looping Cable 2 provided Kollector Elite DVI Display Monitor NETSWITCH 100Base T 1000Base T recommended BE oe oe 0 2 8 ROUTER DATT Te rer Alternate connection for PTZ Internet Auxiliary Fan on 240 fps Models 230VAC Power Cable Not Provided Sensor El Adapter Printer USB Parallel MIC Twisted Pair S Video Display Monitor PR RXD RXD NE ag Gis TF Termination Box 16 provided Keyboard Mouse Figure 2 1 Kollector Elite Quick Installation Quick Installation e 3 XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 3 Installation For novice or first time installers these steps provide the most thorough and accurate instructions About This Chapter This chapter details the complete installation of the Kollector Elite Digital Video Recorder The following sections provide information as follows e Unpacking the Recorder defines how to remove the unit and accessories from the box e Required Items for Installation defines items needed for installation e Unit Components defines all connections on the front and rear panels and th
10. XX112 02 00 Vicon Industries Inc does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation This system has not been designed to be used in life critical situations and must not be used for this purpose FE ce vo Copyright 2004 Vicon Industries Inc All rights reserved Product specifications subject to change without notice ViconNet and its logo are trademarks of Vicon Industries Inc Kollector Elite Kollector Pro VN 306T the Workstation and their logos are trademarks of Vicon Industries Inc Vicon and its logo are registered trademarks of Vicon Industries Inc Windows is a trademark of Microsoft Corp VICON INDUSTRIES INC 89 ARKAY DRIVE HAUPPAUGE NEW YORK 11788 TEL 631 952 CCTV 2288 FAX 631 951 CCTV 2288 TOLL FREE 800 645 9116 24 Hour Technical Support 800 34 VICON 800 348 4266 UK 44 0 1489 566300 WEB www vicon cctv com Vicon Part No 8009 8112 02 00 Section 1 Rev 904 UOHE E SU Dear Valued Customer Thank you for selecting Vicon systems and products for your video needs Since Vicon s beginning in 1967 our only business has been the design engineering and production of the highest quality video systems and equipment for use in a wide variety of security safety control surveillance and communication applications We stand behind the q
11. back up the Kollector Elite e Refer to Chapter 3 Configuring the ViconNet System in the Kollector Elite Software Manual XX112 3X NOTE The backup procedure should be performed whenever a change is made to the system settings XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Maintenance e 15 To check the front and rear fans 1 Turn the Kollector Elite off and then open the front door 2 3 4 5 Aca UTION Do not open the recorder s top cover for any reason Failure to follow this instruction can result Open the filter housing on the left hand side Carefully remove the filter look at the front fan and ensure it is operating properly Look at the fan in the rear of the Kollector Elite and ensure it is operational When you have finished replace the filter turn the Kollector Elite back on and then close the front door in serious injury to the user and void the manufacturer s warranty 16 e Maintenance XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 7 Shipping Instructions Use the following procedure when returning a unit to the factory 1 Call or write Vicon for a Return Authorization R A at one of the locations listed below Record the name of the Vicon employee who issued the R A Vicon Industries Inc 89 Arkay Drive Hauppauge NY 11788 Phone 631 952 CCTV 2288 Toll Free 1 800 645 9116 Fax 516 951 CCTV 2288 For service or returns from countries i
12. cables to loop the video inputs out Relay VO Connections Not currently used Video Camera Inputs Standard BNC F connectors used for analog camera video input SMSR Aux Connections Standard RJ 45 connectors used for sensor and communication input for each video channel SMSR connectors are used for sensors microphones speakers and PTZ cameras Power Switch Used to power on and off the power supply of the recorder Power Receptacle Used to connect the provided Power Cable Keyboard Port A mini DIN type connector used to connect a standard PC keyboard not included Mouse Port A mini DIN type connector used to connect the provided optical mouse Network Port A standard RJ 45 connector used to connect to a LAN WAN USB Connectors Used for optional devices 6 Installation XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder e Parallel Port Used for general printing e Serial COM Port Used to connect system serial devices e Speaker Output Mini phono type connector used for sound card audio output e LCD Monitor Output Used for digital video output to a monitor A DVI to VGA adapter is provided for use with VGA monitors e Auxiliary Fan Used to cool the unit during operation available on 240 FPS models only NOTE Connector locations may vary according to KE type Mounting There are two types of mounting recommended for the recorder either desktop or rack For more details refer to the Kollecto
13. e T RJ 45 jack Keyboard Port Mini DIN jack PS2 Mouse Port Mini DIN jack PS2 All BNC connectors 1 0 V peak to peak All BNC connectors 75 ohms NTSC PAL EIA and CCIR XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Technical Information e 21 Mechanical Characteristics Application Mounting Dimensions Weight Construction Color Shipping Dimensions Shipping Weight Shipping Volume Indoor Desktop or standard 19 in 483 mm rack mount and stackable 4U height Height H 7 0 in 178 mm Width W 19 0 in 483 mm Depth D 22 0 in 558 8 mm for 120 fps models 24 25 in 615 95 mm for 240 fps models with extra fan Note Refer to Figure 10 1 Approximately 45 0 Ib 20 5 kg Steel case and hardware Black Length 25 in 635 mm Width 24 in 610 mm Height 12 in 305 mm Approximately 53 Ib 24 kg 4 2 ft 0 12 m Environmental Characteristics Operating Temperature Operating Humidity Range Storage Temperature Range Storage Humidity Range Range 32 to 104 F 0 to 40 C 0 to 95 relative non condensing 4 to 158 F 20 to 70 C 0 to 95 relative non condensing 22 e Technical Information XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder 15 CONNECTOR DEPTH KOLLECTOR ELITE 240 models 16 75 15 CONNECTOR DEPTH KOLLECTOR ELITE KOLLECTOR ELITE Figure 10 1 Kollector Elite Dimens
14. e ded OR EE EE RO ER EE Table 8 1 Recommended Coaxial Cable Types ii Table 8 2 Picture Quality vs Cable Length i Table 9 1 Recommended Individually Shielded Twisted Pair Cable Types see se ee ke ee ke ee Table 10 1 Technical Information dee dee a ia iv eList of Figures XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Chapter 1 Introduction The information in this manual covers the installation and operation of the Kollector Elite Digital Video Recorder This system should only be installed by a qualified technician using common hand tools and approved materials in accordance with national state and local wiring codes The Kollector Elite is an intelligent and rugged Digital Video Recorder It is a state of the art Windows based computer in an attractive industrial steel case The Kollector Elite is sold in prepackaged configurations with choices of video frame per second rates and hard drive sizes and uses an Intel Pentium CPU platform All versions run the same Vicon ViconNet software application For software information refer to the Kollector Elite Software manual XX112 3X where X is a revision number between 0 and 9 Kollector Elite can be networked with all models of Kollector Pro VN 306T Transmitters and ViconNet workstations to create a complete system Kollector Elite complies with UL standard 2044 CSA safety standard C22 2 No 1 and
15. eir use e Mounting defines all methods of securing the recorder for permanent use e Installing the Kollector Elite describes how to install all necessary peripheral devices directly to the recorder as well as how to install all necessary peripheral devices to the Termination Boxes Unpacking the Recorder Carefully open the carton Remove the Accessory Kit and the recorder from the box and place them on a large flat working surface Open the Accessory Kit and verify the contents against the list in Table 1 1 page 2 Required Items for Installation To properly install the recorder there must be simple hand tools available such as a screwdriver wrenches pliers and wire cutters strippers To setup the recorder for operation there must be a keyboard available to operate the GUI 4 e Installation XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Unit Components This section describes the Kollector Elite unit s front and rear panels Front Panel Controls and Connections The following picture shows the Kollector Elite front panel Each panel component is described in the table below Keyboard Port CD RW Drive Floppy Drive Mouse Port LED Indicator Power Switch Front Cover Status LEDs Green camera recording Red device alarm Keylock Figure 3 1 Front Panel Layout The Kollector Elite s front panel contains the following components e Keyboard Port A USB type connector used to connect a s
16. espective holders XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Important Notice e i About This Manual This Kollector Elite Installation and Operation Manual is comprised of the following chapters Chapter 1 Introduction introduces the Kollector Elite Video Network Digital Video Recorder Chapter 2 Quick Installation is for experienced installers and provides an illustration of how the Kollector Elite should be connected to its various peripherals Chapter 3 Installation is for novice or first time installers and provides step by step instruction on how to install the Kollector Elite Chapter 4 Operation describes how to power on boot and power off the Kollector Elite Chapter 5 Troubleshooting provides information on what to do in the unlikely event of a Kollector Elite malfunction Chapter 6 Maintenance provides information on maintaining the Kollector Elite Chapter 7 Shipping Instructions describes the procedure to be followed when sending a Kollector Elite back to Vicon Chapter 8 Coaxial Cable Recommendations provides technical information for the recommended coaxial cable types Chapter 9 Twisted Pair Cable Recommendations provides technical information for the recommended twisted pair cable types Chapter 10 Technical Information provides the electrical mechanical and environmental specifications for the Kollector Elite ii e About This Manual XX112 02 00 Rev 904 Kollector E
17. ions XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Technical Information e 23 Vicon Industries Inc Corporate Headquarters 89 Arkay Drive Hauppauge New York 11788 631 952 CCTV 2288 800 645 9116 Fax 631 951 CCTV 2288 Vicon Europe Headquarters Brunel Way Fareham PO15 5TX United Kingdom 44 0 1489 566300 Fax 44 0 1489 566322 Brussels Office Planet Il Unit E Leuvensesteenweg 542 B 1930 Zaventem Belgium 32 2 712 8780 Fax 32 2 712 8781 Far East Office Unit 5 17 F Metropole Square 2 On Yiu Street Shatin New Territories Hong Kong 852 2145 7118 Fax 852 2145 7117 Internet Address www vicon cctv com
18. is in the ON position I pressed in 2 Open the front panel cabinet and press the front panel toggle Power Switch towards the I position The button will switch back to the O which is its default position even when the system is running IMPORTANT Do not press any keyboard buttons at this time When the recorder completes booting and the Main Screen is displayed For more details refer to the Kollector Elite Software Manual XX112 3X Powering Off the Recorder To power off the system e With the recorder booted and operational press the Shutdown button in the Site Setup window Follow the screen prompts and the system will return to the ViconNet desktop Use the Start button to completely shutdown the system OR this not recommended due to the possibility of data loss Momentarily press the power switch The system switches off component by component XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Operation e 13 Chapter 5 Troubleshooting If the Kollector Elite does not power up correctly check the following e Verify that the outlet or UPS supplying power is actually active Plug in a lamp or other device to the outlet to verify the 120 or 230 VAC If voltage is present proceed to the next item e Verify that the rear panel Power Switch is in the ON position I pressed in If the recorder fails to boot proceed to the next item e Press the front panel Power Switch so it is in the
19. lite Network Digital Video Recorder Table of Contents CHAPTER 1 INTRODUCTION rinite How to Use This Manual E For Experienced Installers c s eal dne Ge SEEN pea nia For Novice Installers octo iaia ani Udo EM ard minde ACCOSSORy KI EE Unpacking and AL Ede de die RE EE N OE OE EE EE EI CHAPTER 2 QUICKINSTALLATION GG Jai CHAPTERS INSTALLATION Rca About This Chaptef ER EE EE EE ER EE N Required Items for Installation iaia EER EG GR KEER EDE ER ee EE EED EG RA KERE RE ER Ee Re EE Unit CompoODnGen sS icit OE EE RE RE N ER EE N ER Front Panel Controls and Connections ee ee ee ee ee ee ee ee ee ee adiera ee ee si sess da sanas dada Rear Panel Controls and ConnectionS ee ee ee ee ee ee ee ee ee ee ee ee ee ee a nnne ee sa sana dd Mountingi iii iaia EE EE EE SEERE nio n k B 4 4 Unpacking the TO rentra nrat rantan naarat ranra nr atrata nran atn a 4 E E E Step 2 Connecting External Hardware to Termination Boxes eene Step 3 Connecting Looping Cables ii see se Ke Ge RE Ke Ge Ke ee einen nans Ge nnn assent as Ge ananas essa s ases aan nnd Step 4 Connecting the Power Supply nennen erre ee sn nenne nnne ee ee nee CHAPTER 4 OPERATION e About This Chapter tre ko REKE RR ER REREKRERARERRRA RE END NN ER SERERE DEERE ER REKEN
20. losed Detector The resistor should be connected between the detector s wire and the ground GND connector NOTE 16 1KQ resistors are included Normally Open Normally Closed Figure 3 4 Resistor Connection Types 10 e Installation XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Step 3 Connecting Looping Cables Looping cables are required only when you wish to retrieve video output from the Kollector Elite The purpose of the cables is to transmit video signals to a second transmitter Each cable transmits 8 video signals Looping 1 transmits signals from cameras 1 to 8 and Looping 2 from cameras 9 to 16 To connect the cables 1 Using the two provided Video Looping Cable Assemblies insert the large D type connector end into one of the two Video Looping Output ports 2 Connect each of the remaining BNC F connectors to the Video Camera Input ports as defined in the following table In order to connect the video male to male BNC cables are required not included Cable Color Looping 1 Cameras Looping 2 Cameras Red 1 9 Green 2 10 Blue 3 11 Gray 4 12 Black 5 13 Yellow 6 14 White 7 15 Brown 8 16 NOTE Each BNC cable is labeled for the relevant channel For example V6680 VIDEO 2 10 green wire transmits video from camera 2 if the D type is connected to Looping No 1 or camera 10 if connected to Looping No 2 Each channel wire is designated a unique color Eight BNC Connectors D
21. n Europe contact Vicon Europe Ltd Brunel Way Fareham PO15 5TX United Kingdom Phone 44 0 1489 566300 Fax 44 0 1489 566322 2 Attach a sheet of paper to the unit with the following information e Name and address of the company returning the unit e Name of the Vicon employee who issued the R A e R A number e Brief description of the installation e Complete description of the problem and circumstances under which it occurs e Units original date of purchase if still under warranty 3 Pack the unit carefully Use the original shipping carton or its equivalent for maximum protection 4 Mark the R A number on the outside of the carton on the shipping label XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Shipping Instructions e 17 Chapter 8 Coaxial Cable Recommendations Aca UTION Careful selection of proper cable is essential to obtain the best performance from this equipment Vicon assumes no responsibility for poor performance when cables other than those recommended or equivalent are installed In all cases coaxial cable impedance should be 75 ohms Materials Use only a pure copper center conductor Do not use a copper plated steel or aluminum center conductor as they will result in poor quality video Solid core bare copper conductor is the best type where flexing and bending will be minimal If severe bending and flexing is required for installation use a stranded center conducto
22. p www belden com 800 235 3361 Alpha Wire Company http www alphawire com 800 52 ALPHA 522 5742 West Penn Wire http www westpenn cdt com 800 245 4964 18 e Coaxial Cable Recommendations XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Table 8 2 Picture Quality vs Cable Length Picture Quality Maximum Cable Run ft m RG 59 U RG 6 U RG 11 U Usable picture 1100 350 1500 450 2400 750 Clean picture 820 250 1000 300 1600 500 Best picture 400 120 530 160 820 250 For longer cable runs use a Vicon Video Amplifier to obtain a suitable picture XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Coaxial Cable Recommendations e 19 Chapter 9 Twisted Pair Cable Recommendations Aca UTION Careful selection of the proper cable is essential to obtain the best performance from this equipment Vicon assumes no responsibility for poor performance when cables other than those recommended are installed Materials Use a pure copper stranded conductor with or without a tin plating to obtain a low DC resistance Do not use cable with either a steel or an aluminum stranded conductor because these do not transfer signals effectively for long distances The preferred insulation and cable jacket is Polyvinyl chloride PVC It has better electrical characteristics than polyethylene and resists flames sunlight and most solvents but is more vulnerable to moisture
23. r Never exceed the manufacturer s minimum bend radius specification Use cellular foam polyethylene dielectric except where heavy moisture exists For moisture conditions use solid polyethylene dielectric cable with a heavy exterior insulation The shield must be copper braid providing 95 or better coverage Cable Types The cable types listed below are the most common 75 ohm types used They vary in size diameter dielectric type and net DC resistance The larger cable results in a lower DC resistance and better video quality with increased difficulty in handling and installation Let the required picture quality and cable distance provide a guide in choosing the best cable type For cables other than the approved Vicon types below contact the manufacturers listed below Note that BC refers to bare copper and TC refers to tinned copper Table 8 1 Recommended Coaxial Cable Types DC Resistance Cable Belden Alpha West Penn Type Center Type Shield and ohms 1000 ft Type Type No Type No Type No Conductor Coverage km RG 11 U 8213 9847 811 4811 14 Solid BC BC braid 95 2 6 8 5 RG 6 U 9248 9804C 806 4806 18 Solid BC Foil 61 TC braid 100 7 5 24 6 RG 59 U 8281 815 20 Solid BC 2 TC braids 96 9 9 32 5 RG 59 U 9259 9803 816 22 Stranded BC BC braid 95 15 0 49 RG 59 U 9659 22 Stranded BC BC braid 95 15 0 49 Requires special BNC M connector due to 0 305 nominal O D Belden Inc htt
24. r Pre installation Manual XX112 7X Desktop The desk or table must provide a surface of suitable strength for the Kollector Elite s weight of 45 Ib 20 5 kg In addition there must be area left around the cabinet to provide suitable airflow for cooling Do not place heavy items on the cover Rack The recorder was designed to be mounted in a standard 19 inch 483mm wide vertical rack Use the provided rack mount ears to connect the recorder to the rack using hardware provided with the rack It is recommended that at least 74 standard rack height of space be left in between multiple recorders mounted in the same rack for cooling purposes WARNING Failure to leave space for cooling between recorders may result in malfunctioning and possible failure of the recorder XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Installation e 7 Installing the Kollector Elite After the recorder is mounted permanently follow the steps in this section to install the Kollector Elite unit hardware e Step 1 Connecting the Hardware below e Step 2 Connecting External Hardware to Termination Boxes page 9 e Step 3 Connecting Looping Cables page 11 e Step 4 Connecting the Power Supply page 12 IMPORTANT NOTES The connection of external hardware may require simple hand tools Do not apply power or plug in the recorder to any outlet until instructed to do so Disable the AC power to prevent installer injury and damage to
25. rt the other end into the desired SMSR Aux Connections port 1 16 on the recorder NOTE For additional information regarding the devices connected to the SMSR connectors refer to Step 2 Connecting External Hardware to Termination Boxes page 9 8 e Installation XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder e Insert the female end of the provided 120VAC Power Cable into the recorder s Power Receptacle Do not connect the remaining end to a power receptacle until instructed If using 230VAC power it will be necessary to obtain a suitable power cord for use This cable is a standard computer 230 VAC power cord e Turn ON the Power Switch 2 Connect the monitor to the power source Step 2 Connecting External Hardware to Termination Boxes The connection of external hardware to the Termination Boxes requires simple hand tools Do not apply power or plug in the recorder to any outlet until instructed to do so WARNING Disable the AC power to prevent installer injury and damage to the unit With the Termination Boxes mounted permanently connect external devices as follows Communications PTZ Control To connect a PTZ camera control to the Kollector Elite 1 Using a twisted pair cable as defined in Chapter 9 Twisted Pair Cable Recommendations prepare a 4 conductor plus shield type cable by stripping the ends back for use 2 Connectthe PTZ wires to the Termination Box connectors either TX and
26. s Video Level Input Video Input Impedance Video Formats Supported 120 230 VAC 41090 50 60 Hz nominal NOTE Vicon requires the use of uninterruptible power supply systems UPS to prevent voltage fluctuations that can affect operation and cause damage to the equipment Failure to comply with this violates the unit warranty 3A 450 W nominal e Capacity 1000 VA 600 W e Maximum operation time e 16cameras recording displaying with a 15 Sony CRT monitor 18 minutes e 16 cameras recording displaying with a 17 Mag CRT monitor 5 minutes e Input e Voltage 100 240 VAC e Voltage Range 430 with a 4 step AVR e Frequency 47 63 Hz auto detection 25 6 BTU min 6 4 kg cal min NOTE These figures represent the conversion of 100 of the electrical energy to heat Actual percentage of the heat generated will be less and will vary from product to product These figures are provided as an aid in determining the extent of cooling required for an installation CPU Intel amp Pentium IV 2 66 MHz minimum RAM 512 MB HDD 200 900 GB LAN Card 3Com 10 100 Mbps TPO Analog Video Inputs 16 BNC F Analog Video Loopouts 16 in 1 DB 15 connector Power 1 standard 3 conductor female socket VGA Video Output 1 standard VGA port Sensor Input Port 16 NO NC RJ 45 connectors software selectable PTZ Control Port 16 individual RJ 45 connections or one 4 pin terminal block using RS 422 protocol Network Port Ethernet 100Bas
27. tandard PC keyboard not included e Mouse Port A USB type connector used to connect an optical mouse e Status LEDs Used to indicate what the Kollector Elite is doing for example scanning for attached cameras or recording e Keylock Used with the provided key to lock the front door e Power Switch Used to power on the recorder for more details refer to Powering On the Recorder page 13 e LED Indicator Used to display the power status ON means recorder on and OFF means recorder off e Front Cover Used to protect the Kollector Elite s front panel from unauthorized use e Floppy Drive Used as a removable data drive e CD RW Drive Used as a high capacity removable data drive XX112 02 00 Rev 904 Kollector Elite Network Digital Video Recorder Installation e 5 Rear Panel Controls and Connections The following picture shows the Kollector Elite rear panel Each panel component is described below Power Switch Power Receptacle Video camera Inputs Relay VO Connections SMSR Aux Connections 16 Video Looping Outputs ni Auxiliary Fan on 240 fps Models VGA Monitor Output LCD Monitor Output Speaker Output USB Connectors Network Port Keyboard Port Mouse Port Parallel Port Serial com Port Figure 3 2 Rear Panel Layout The Kollector Elite s rear panel contains the following components Video Looping Outputs DB 15 connectors used with provided
28. uality and dependability of every product with an industry leading Beneficial Use warranty If you are not satisfied with a Vicon product or service I would like to know Your complete satisfaction is the mission of every Vicon employee Sincerely Pros Kenneth M Darby President Important Notice This manual is delivered subject to the following conditions and restrictions e This manual contains proprietary information belonging to Vicon Such information is supplied solely for the purpose of assisting explicitly and properly authorized users of the ViconNet system e No part of its contents may be used for any other purpose disclosed to any person or firm or reproduced by any means electronic or mechanical without the express prior written permission of Vicon e The text and graphics are for the purpose of illustration and reference only The specifications on which they are based are subject to change without notice e The software described in this manual is furnished under a license The software may be used or copied only in accordance with the terms of that agreement e Information in this manual is subject to change without notice Corporate and individual names and data used in examples herein are fictitious unless otherwise noted Copyright 2004 Vicon All rights reserved ViconNet is a trademark of Vicon Other company and brand products and service names are trademarks or registered trademarks of their r
Download Pdf Manuals
Related Search