Manual - White Light
Contents
1. Replacing rotating gobos How to replace a gobo in a gobo holder Maintenante i Agia t SEN Ta O ni 23 Upgrading 23 Cleaning insasi peene te actae e A alianti 23 DMX Protocols 2 e ide E Ra E 24 EffecgtSi a e AS 40 Two independent rotating gobo wheels 2 40 Effect wheelS 2 40 High precision pan and tilt 2 40 Ultra high speed strobe effect 40 Prism cc 40 DEVICES ANG accessories ende eee ep alta 41 Included NOMS ci 41 Ordering information a un a L SD ties aeter i ia Ai ini 41 Users notes a ee 43 Safety information 4 WARNINGI Read the safetv precautions in this section before unpacking installing powering or operating this product The G SPOT is intended for professional use oniv It is not suitable for household use Impropre a l usage domestique Review the following safety precautions carefully before installing or operating the device This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the ha2. 16 Level 1 SETTINGS continued Level 2 Level 3 Level 4 Info DIMMING CURVE LINEAR GAMMA CORRECTED x INVERT PAN INVERT TILT SWAP PAN TILT FLIP DISPLAY DISPLAY OFF FAN MODE LINEAR GAMMA CORRECTED MAX POWER ALWAYS 100 CALIBRATION PAN HOME CALIBRATION gt xxxxx PAN POS xxxxx Rev x xx TILT HOME CALIBRATION gt xxxxx PAN POS Rev GOBO 1 SELECT CALIBRATION gt xxxxx GOBO 2 SELECT CALIBRATION gt EFFECT WHEEL 1 CALIBRATION gt xxxxx 17 Level 1 Level 2 Level 3 Level 4 Info SETTINGS CALIBRATION EFFECT WHEEL 2 CALIBRATION gt xxxxx continued continued FROST CALIBRATION gt xxxxx PRISM CALIBRATION gt xxxxx IRIS CALIBRATION gt xxxxx ZOOM CALIBRATION gt xxxxx FOCUS CALIBRATION gt xxxxx FACTORY FACTORY DEFAULT SET DEFAULT TEST OFF LED TEST TESTING RED 2 TESTING RED 1 TESTING BLUE 2 TESTING BLUE 1 TESTING YELLOW TESTING GREEN DISPLAY TEST 18 Level 1 Level 2 Level 3 Level 4 RESET PAN TILT GOBO MODULE ZOOM FOCUS MODULE ALL 19 Gobo replacement Identification of gobo wheel Gobo Wheel 1 Gobo Wheel 2 Closest to light source Closest to front lens Gobo Wheel 1 Gobo Wheel 2 Description
3. 27 24 Channel Mode Standard 0 32767 0 0 50 0 Gobo Index 32768 32799 50 0 50 0 No Effect Gobo Wheel 2 Gobo Continuous rotation 32800 46418 50 0 70 8 Fast gt Slow 15 Indexing CW 0 096 16 Rotation 46419 46919 70 8 71 6 No rotation Shake Gobo Continuous rotation 46920 60538 71 6 92 4 Slow gt Fast CCW 60539 65535 924 100 096 Gobo shake Slow gt Fast 0 200 0 0 78 4 Open gt Close Effect Open fast Close 201 205 78 8 80 4 slow Effect Open slow Close 17 Iris 206 210 80 8 82 4 0 0 Fade fast 211 215 82 7 84 3 Effect Open Close Effect Random Close 216 255 84 7 100 0 un Slow gt Fast pen 28 24 Channel Mode Standard 0 4 0 0 1 6 Open 5 127 2 0 49 8 Indexed ease 128 153 50 2 60 0 Continuous rotation CW Fast gt Slow 18 Continuous rotation CCW 0 0 Wheel 154 179 60 4 70 2 Slow gt Fast Reserved 180 255 70 6 100 0 e Calibration position 0 4 0 0 1 6 5 129 2 0 50 6 Continuous rotation CW Fast gt Slow 19 Prism 0 0 130 130 51 0 51 0 No rotation 131 255 51 4 100 0 Continuous rotation CCW Slow gt Fast 0 5 0 0 2 0 Open 20 Frost 0 096 6 255 2 4 100 0 No frost gt Maximum Frost 21 Zoom 0 255 0 0 100 0 Wide gt Narrow 0 0 Fade 22 Focu
4. Closed 8 15 3 1 5 9 Open 16 151 6 3 59 2 Strobe Slow gt Fast 1 Shutter 152 175 59 6 68 6 Pulse Open Slow gt Fast 10 3 9 176 199 69 0 78 0 Pulse Close Slow gt Fast 200 244 78 4 95 7 Strobe Random Slow gt Fast 245 255 96 1 100 0 Open 2 Intensity 0 255 0 0 100 0 No light gt Maximum light 0 0 3 4 Red 0 255 0 0 100 0 No RED gt Maximum RED 0 0 5 6 No GREEN gt Maximum Green 0 255 0 0 100 0 0 0 7 GREEN 8 No BLUE gt Maximum Blue 0 255 0 0 100 0 0 0 9 BLUE 32 10 CTC 0 0 0 1 6 No CTC 5 2 0 2 0 2000 K 2200 K 15 15 5 9 5 9 High pressure sodium lamp 2700 K 40 40 15 7 15 7 Incandescent lamp 3000 K 54 54 21 2 21 2 Halogen Tungsten lamp 3200 K 65 65 25 5 25 5 Warm metal halide lamp 4000 K 105 105 41 2 41 2 Clear metal halide lamp 4200 K 115 115 45 1 45 1 Cool white fluorescent lamp 5500 K 177 177 69 4 69 4 Daylight metal halide lamp 216 216 84 7 84 7 6300 238 238 93 3 93 3 80009 K 255 255 100 096 100 0 10 000 K 30 Channel Mode Extended 4 0 0 33 30 Channel Mode Extended 270 Front 11 lens mains Pan 0 65535 0 0 100 0 270 to 270 32767 50 12 power input Tilt 0 120 Front 13 lens bas
5. Near 0 0 28 37 30 Channel Mode Extended 0 4 0 0 1 6 No Effect 5 15 2 0 5 9 Reserved No effect 16 26 6 3 10 2 Reserved No effect 27 32 10 6 12 5 Shutter Black RED 33 38 12 9 14 9 Shutter Black GREEN 29 Camion 39 44 15 3 17 3 Shutter Black BLUE 0 0 45 50 17 6 19 6 Shutter Black WHITE 51 56 20 0 22 0 Shutter Black Magenta 57 62 22 4 24 3 Shutter Black Yellow 63 68 24 7 26 7 Shutter Black Cyan 69 255 27 1 100 0 Reserved No effect 38 30 Channel Mode Extended 0 4 0 0 1 6 No Function Hold 5 9 2 0 3 5 Full Reset 3 seconds Hold 10 14 3 9 5 5 Pan Reset 3 seconds Hold 15 19 5 9 7 5 Tilt Reset 3 seconds Hold Control 20 24 7 8 9 4 Gobo Reset 30 3 seconds Channel Hold 25 29 9 8 11 4 Zoom Reset 3 seconds 30 34 11 8 13 3 Sleep Mode See note Hold 35 39 13 7 15 3 Display Off 3 seconds Hold 40 44 15 7 17 3 Display On 3 seconds 45 255 17 6 100 0 Reserved No function 1 All other channels must be zero and this has to be held for 30 sec device will wake up on a full reset Effects Two independent rotating gobo wheels The two independent rotating gobo wheels has five slots plus one open position on each to control the shape of emitted light Each gobo is indexable with bi directional ro
6. and a Z virtually unlimited color palette two independent rotating gobo wheels and can easily be controlled by wired and wireless DMX The device also offers RFID and NFC low power consumption and an expected lifetime of the multiple LED s of 50 000 hours Pan lock Tilt lock Yoke handle Base handle Head fan grill one of two shown Display panel Safety wire attachment point TOA gt Fuse DMX in J DMX out K Power in L Power cord At 70 of luminous output under the manufacturer s test conditions 8 Unpacking Unpack the device and inspect it to ensure that it has not been damaged in transport The G Spot is supplied with User manual One Neutrik TRUE1 power input connector 2 78 in Two Omega brackets with 1 4 turn fasteners The device is designed for use in wet locations and is IP65 rated When selecting a location for the device ensure that it is situated away from public throughfares and protected from contact with people it has adequate ventilation Transportation Always use the supplied packaging for transportation and storage Release the pan tilt locks when transporting the device Leaving the pan tilt locks applied may cause damage to the device Installation Rigging A WARNING Always secure elevated devices with a safety cable The G Spot may be installed in any orientation Always use two Omega bra
7. 50 Fade 10 front Pan 32767 0 20 0 096 7 896 Open 21 41 8 296 16 1 Gobo 1 Position 1 42 62 16 596 24 3 Gobo 1 Position 2 63 83 24 796 32 596 Gobo 1 Position 3 Gobo Wheel 1 84 104 32 996 40 896 Gobo 1 Position 4 11 Closest to 105 127 41 296 49 896 Gobo 1 Position 5 0 096 Snap light source Gobo Wheel Continuous 128 191 50 296 74 996 Fast gt Slow rotation CW 192 192 75 3 75 3 No rotation Gobo Wheel Continuous 193 255 75 7 100 0 gt rotation CCW 26 24 Channel Mode Standard 0 32767 0 0 50 0 Gobo Index 32768 32799 50 0 50 0 No Effect Gobo Wheel 1 Gobo Continuous rotation 32800 46418 50 0 70 8 Fast gt Slow 12 Indexing CW 0 0 Fade 13 Rotation 46419 46919 70 8 71 696 No rotation Shake Gobo Continuous rotation 46920 60538 71 6 92 4 Slow Fast CCW 60539 65535 924 100 0 Gobo shake Slow gt Fast 0 20 0 0 7 8 Open 21 41 8 2 16 1 Gobo 1 Position 1 42 62 16 5 24 3 Gobo 1 Position 2 63 83 24 7 32 5 Gobo 1 Position 3 Gobo Wheel 2 84 104 32 9 40 8 Gobo 1 Position 4 14 Closest to 105 127 41 2 49 8 Gobo 1 Position 5 0 0 Snap light source Gobo Wheel Continuous 128 191 50 2 74 9 Fast gt Slow rotation CW 192 192 75 3 75 3 No rotation Gobo Wheel Continuous 193 255 75 7 100 0 Slow gt Fast rotation CCW
8. Part No No Description Part No Open Open gobo 37000001 Open Open gobo 37000001 1 Spin cycle 37005002 1 Breakup bricks 37005006 2 Ring 37005007 2 Spiral leaf 37005010 3 Bar 37005008 3 Dots 37005003 4 Triangle 37005009 4 Kaleidoscope gems 37002001 5 Concentric 37005004 5 Fire up close 37005001 20 Replacing rotating gobos To replace one or more gobos Disconnect the device from power and allow to cool Position the head and apply the tilt lock Before removing one of the rear head covers identify where gobo wheel covers 1 and 2 are positioned When the head of the device is facing upwards cover gobo wheel 2 is located at the side of the head corre sponding to the pan lock A See figure below Remove the relevant rear head cover Remove the gobo wheel cover for access to the gobo wheel Turn the relevant gobo wheel until the gobo you want to replace is accessible Unhook the end of the spring and turn it upwards Pull the gobo holder out of the gobo wheel FR Cover Gobo Wheel 1 Cover Gobo Wheel 2 21 How to replace gobo gobo holder Place gobo with silver side towards the light source Align index markers on the gobo and the gobo holder as shown below Insert the gobo holder and align it with the index marker on the gobo wheel as shown below If necessary continue replacing gobos one by as described above If no further service is necessary reins
9. 06 95 EC Low Voltage Directive A 2011 65 EU RoHS2 Directive RoHS The information in this document is subject to change without notice 42 User s notes 43 SGM SGM A S Sommervej 23 8210 Aarhus V Denmark Tel 45 70 20 74 info sgmlight com www sgmlight com
10. 96 Strobe Slow Fast 1 Shutter 152 175 59 696 68 6 Pulse Open Slow gt Fast 10 3 9 Snap 176 199 69 0 78 0 Pulse Close Slow gt Fast 200 244 78 4 95 7 Strobe Random Slow gt Fast 245 255 96 1 100 0 Open Intensity 0 255 0 0 100 0 No light gt Maximum light 0 0 Fade Red 0 255 0 0 100 0 RED gt Maximum RED 0 0 Fade No GREEN gt Maximum 4 Green 0 255 0 0 100 0 0 0 Fade GREEN No BLUE gt Maximum 5 Blue 0 255 0 0 100 0 0 0 Fade 24 24 Channel Mode Standard 0 4 0 0 1 6 No CTC 5 2 0 2 0 2000 K 2200 K 15 15 5 9 5 9 High pressure sodium lamp 2700 K 40 40 15 7 15 7 Incandescent lamp 3000 K 54 54 212 212 Halogen Tungsten lamp 3200 K 65 65 25 5 25 5 6 CTC Warm metal halide lamp 0 0 Fade 4000 K 105 105 41 2 41 2 Clear metal halide lamp 4200 K 115 115 45 1 45 1 Cool white fluorescent lamp 5500 K 177 177 69 4 69 4 Daylight metal halide lamp 216 216 84 7 84 7 6300 K 238 238 93 3 93 3 8000 K 255 255 100 0 100 0 10 000 K 25 24 Channel Mode Standard 270 Front 7 lens mains Pan 0 65535 0 0 100 0 270 to 270 32767 50 8 power input Tilt 0 120 Front 9 lens base Tilt 0 65535 0 096 100 096 120 to 120 32767
11. G SPOT MOVING HEAD Dimensions Measurements in millimetres and inches in parentheses Drawing not to scale G SPOT USER MANUAL 2014 SGM Information subject to change without notice SGM and all affiliated companies disclaim liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual The SGM logo the SGM name and all other trademarks in this document pertaining to services or products by SGM or its affiliates and subsidiaries are trademarks owned or licensed by SGM or its affiliates or subsidiaries The original edition of this document is in English All other language editions are translations of the original edition This edition applies to firmware version 1 00 or later REV 4 Contents A Er EET 2 Safety information edente eet iaia ana 6 M 8 Unpacking A qr T 9 DN MER a 9 Installation A ee an ne ee 10 ssa mA 12 Control panel Operations tii ua ped aa 13 USING the ontrol panel zzz sine a a B RARI e ent one E o EE rite ser fonte FEE 13 DMX start address A A nee AE 13 Control panel menus narran 14 G bo replacement usu A a Identification Of gobo wheel
12. annel Mode Extended 0 32767 0 0 50 0 Gobo Index 32768 32799 50 0 50 0 No Effect Gobo Wheel 2 Gobo Continuous rotation 32800 46418 50 0 70 8 Fast gt Slow 19 Indexing CW 0 0 20 Rotation 46419 46919 70 8 71 6 No rotation Shake Gobo Continuous rotation 46920 60538 71 6 92 496 gt CCW 60539 65535 92 4 100 0 Gobo shake Slow gt Fast 0 200 0 0 78 4 Open gt Close Effect Open fast Close 201 205 78 8 80 4 slow Effect Open slow Close 21 Iris 206 210 80 8 82 4 0 0 fast 211 215 82 7 84 3 Effect Open Close Effect Random Close 216 255 84 7 100 0 Slow gt Fast pen 36 30 Channel Mode Extended 0 4 0 0 1 6 Open 5 127 2 0 49 8 Indexed 128 153 50 2 60 0 Continuous rotation CW Fast gt Slow ec 22 Continuous rotation CCW 0 0 Wheel 154 179 60 4 170 2 Slow gt Fast Reserved 180 255 70 6 100 0 UM m Calibration position 0 4 0 0 1 6 Open 5 129 2 0 50 6 Continuous rotation CW Fast gt Slow 23 Prism 0 096 130 130 51 0 51 0 No rotation 131 255 51 4 100 0 Continuous rotation CCW Slow gt Fast 0 5 0 0 2 0 Open 24 Frost _ R 0 0 6 255 2 4 100 0 No frost gt Maximum Frost 25 Zoom 0 255 0 0 100 0 Wide gt Narrow 0 0 26 27 Focus 0 255 0 0 100 0 Far gt
13. ckets to rig the device Lock each brack et with both 1 4 turn fasteners The fasteners are locked only when T turned fully clockwise a Ciel Always fasten safety cables between the load bearing support structure and the attachment points on the device The safety cables must be able to bear at least 10 times the weight of the device CAUTION Always use two safety wires Min safety wire gauge 5 mm Max safety wire length free fall 30 cm 11 in Make sure the slack of the safety wire is at a minimum Never use the carrying handles for secondary attachment 10 Start the rigging process by blocking the work area below and make sure the work is performed from stable platform 1 Check that the clamps are undamaged and can bear at least 10 times the weight of the device Check that the structure can bear at least 10 times the weight for all in stalled devices clamps cables etc 2 Bolt each clamp securely to an Omega bracket with an M12 1 2 bolt min grade 8 8 and lock nut 3 Align an Omega bracket with two 1 4 turns in the base Insert the fasteners into the base and turn both levers a full 1 4 turn clockwise to lock Install the second Omega bracket 4 Working from a stable platform hang the device on a truss or other structure Note the position of the base The
14. e Tilt 0 65535 0 0 100 0 120 to 120 32767 50 14 front Pan 32767 0 20 0 0 7 8 Open 21 41 8 2 16 1 Gobo 1 Position 1 42 62 16 5 24 3 Gobo 1 Position 2 63 83 24 7 32 5 Gobo 1 Position 3 Gobo Wheel 1 84 104 32 9 40 8 Gobo 1 Position 4 15 Closest to 105 127 41 2 49 8 Gobo 1 Position 5 0 0 light source Gobo Wheel Continuous 128 191 50 2 74 9 Fast gt Slow rotation CW 192 192 75 3 75 3 No rotation Gobo Wheel Continuous 193 255 75 7 100 0 Slow gt Fast rotation CCW 34 30 Channel Mode Extended rotation CCW 0 32767 0 0 50 0 Gobo Index 32768 32799 50 0 50 0 No Effect Gobo Wheel 1 Gobo Continuous rotation 32800 46418 50 0 70 8 Fast gt Slow 16 Indexing CW 0 0 17 Rotation 46419 46919 70 8 71 6 No rotation i Shake Gobo Continuous rotation 46920 60538 71 6 924 Slow gt Fast CCW 60539 65535 92 4 100 0 Gobo shake Slow gt Fast 0 20 0 0 7 8 Open 21 41 8 2 16 1 Gobo 1 Position 1 42 62 16 5 24 3 Gobo 1 Position 2 63 83 24 7 32 5 Gobo 1 Position 3 Gobo Wheel 2 84 104 32 9 40 8 Gobo 1 Position 4 18 Closest to 105 127 41 2 49 8 Gobo 1 Position 5 0 0 light source Gobo Wheel Continuous 128 191 50 2 74 9 Fast gt Slow rotation CW 192 192 75 3 75 3 No rotation Gobo Wheel Continuous 193 255 75 7 100 096 Slow Fast 35 30 Ch
15. front of the base is to the right when looking at the display panel and when the device is sitting on the base Tighten the clamps 5 Install two safety wires that each can bear at least 10 times the weight of the unit The attachment points are designed to fit a carabiner 6 Check that the pan tilt locks are released A and B Verify that there are no combustible materials or surfaces to be illuminated within 0 3 m 11 in of the de vice 7 Check that there is no possibility of head or yoke colliding with other devices Connecting AC power The G Spot can operate on any 200 240V 50 60 Hz mains power supply Connect the device to power using a cable with a Neutrik powerCON TRUE1 connector supplied with the device Connect both DMX in and DMX out cables in order to maintain the device IP65 a rd Fuse Power DMX DMX In Out In The device must be grounded Wire Color Conductor earthed and be able to be isolated Brown live from AC power The AC power Blue neutral green yellow ground earth supply must incorporate a fuse or circuit breaker for fault protection 12 Control panel operations You can configure individual device settings read out data and view error messages in the graphic display When the device is powered on it boots and resets then displays the DMX start address and any status messages Using the control panel Click the arrow buttons to scroll up and down
16. menus Click the OK button to enter a menu or make a selection Press the ESC button to step backwards through the menus DMX start address The DMX start address is the first channel used to receive instructions from the controller For independent control each device must be assigned its own start address If you give two devices the same address they will behave identically Address sharing can be useful for diagnostic purposes and svmmetrical control Select DMX address using the arrow buttons 13 Control panel menus Level 1 Level 2 Level 3 Level 4 Info DMX MODE STANDARD EXTENDED INFO GENERAL INFO PRODUCT SN RDM LABEL RDM ID SOFTWARE MAIN VERSION SMPS PAN TILT GOBO ZOOM TIMERS RED D H GREEN D H BLUE D H RUNNING HOURS D H 14 Level 1 INFO continued Level 2 Level 3 Level 4 Info DMX VIEW 001 y 507 TEMPERATURES LED R G B SMPS PAN TILT GOBO FOCUS BASE HEAD HUMIDITY B H FANS LED FAN 1 rpm LED FAN 2 rpm HEAD rpm BASE rpm LOG FIRMWARE BUILD BUILD UPTIME D H M S 15 Level 1 INFO continued Level 2 DEBUG Level 3 0 17 54 Level 4 Info ERRORS SMPS PAN TILT GOBO ZOOM SETTINGS WIRELESS DMX LOG OFF STATUS SIGNAL STRENGHT CRMX PAIRD RDM ACTIVE DMX ACTIVE CRMX RATE Hz ENABLE DISABLE CRMX gt DMX
17. s 0 255 0 0 100 0 Far gt Near 0 0 Fade 29 24 Channel Mode Standard 0 4 0 0 1 6 No Effect 5 15 2 0 5 9 Reserved No effect 16 26 6 3 10 2 Reserved No effect 27 32 10 6 12 5 Shutter Black RED 33 38 12 9 14 9 Shutter Black GREEN 23 39 44 15 3 17 3 Shutter Black BLUE 0 0 Snap 45 50 17 6 19 6 Shutter Black WHITE 51 56 20 0 22 0 Shutter Black Magenta 57 62 22 4 24 3 Shutter Black Yellow 63 68 24 7 26 7 Shutter Black Cyan 69 255 27 1 100 0 Reserved No effect 30 24 Channel Mode Standard 0 4 0 0 1 6 No Function Hold 5 9 2 0 3 5 Full Reset 3 seconds Hold 3 10 14 3 9 5 5 Pan Reset seconds Hold 15 19 5 9 7 5 Tilt Reset 3 seconds Hold Control 20 24 7 8 9 4 Gobo Reset 24 3 seconds Snap Channel Hold 25 29 9 8 11 4 Zoom Reset 3 seconds 30 34 11 8 13 3 Sleep Mode See note Hold 35 39 13 7 15 3 Display Off 3 seconds Hold 40 44 15 7 17 3 Display On 3 seconds 45 255 17 6 100 0 Reserved No function 1 All other channels must be zero and this has to be held for 30 sec fixture will wake up on a full reset 31 30 Channel Mode Extended Default Channel Name DMX Value DMX Percentage Description Info DMX value 0 7 0 0 2 7
18. tall the gobo wheel cover To maintain the device s IP65 rating it is important to fasten the gobo covers to 1 Nm 22 Maintenance When cleaning the device do not use any product that contains abrasives or solvents that can damage plastic or painted surfaces Use a clean cloth with water and a standard household cleaner To maintain adequate cooling fans must be cleaned periodically Upgrading the firmware The firmware installed on the device can be identified using the Info Software version menu We recommend that you keep your device s firmware up to date Visit http www sgmlight com to download the latest firmware To perform firmware updates you need a Windows based personal computer and a SGM USB 5 Pin XLR upload cable available from your SGM distributor Cleaning To maintain optimal performance regular cleaning is essential Cleaning schedules will vary greatly depending on the operating environment and the installation should therefore be checked at frequent intervals within the first few weeks of operation to see whether cleaning is necessary This procedure will allow you to assess cleaning requirements in your particular situation If in doubt consult your SGM dealer for a suitable maintenance schedule 23 DMX protocols Default Fader Channel Name DMX Value DMX Percentage Description Info DMX value uias 0 7 0 096 2 796 Closed 8 15 3 196 5 996 Open 16 151 6 396 59 2
19. tation The standard gobo set includes both breakup patterns geometric gobos and full colored gobos Effect wheels The G Spot has two effect wheels for generating optical effect The two effect wheels operate as an extension to one an other for achieving continuous animation effect High precision pan and tilt The G Spot has a 16 bit pan and tilt control with a 540 pan and 240 tilt movement with feedback Ultra high speed strobe effect The ultra high speed strobe effect 1 50 Hz introduces instant color control and the possibility to strobe between two or more colors at any speed Random strobe and pulse effects can be generated with variable speed Prism 4 facet rotating prism Frost The soft high quality frost filter is variable from 0 to 100 40 Devices and accessories Included items Two Omega brackets with 1 4 turn fasteners 2 m power cable with Neutrik TRUE1 power connector User manual Ordering information G Spot Moving Head in cardboard box ss Order no G Spot Moving Head in flight case 1 device Order no SGM USB uploadert cable T u a e eR oe tor eid aio Order no 2 m power cable with Neutrik TRUE1 power connector Order no Flighit case 1 device i i ee ae een a certe esed Order no 80021002 80021004 83062011 07860040 82051001 41 APPROVALS AND CERTIFICATIONS Conforms to 2004 108 Directive Conforms to 20
20. zards involved Preventing electric shock WARNING Risk of electric shock Always power off unplug the device before removing covers or dismantling product Ensure that the mains power is off when wiring the device to the AC mains supply Ensure that the device is electrically connected to earth ground Do not apply power if the device is in way damaged Do not immerse the device in water or liquid Avoid personal injury WARNING Take measures to prevent burns and fire Install in a location that prevents accidental contact with the device Install device at least 0 3 m 11 in away from any flammable materials Do cover fans and keep fans clean Allow the device to cool after operation CAUTION Exterior surface temperature after 5 min operation 55 131 F Steady state 65 149 F Preventing burns and fire AN WARNING Take measures to prevent personal injury Do nat look directly at the light source from close range Take precautions to prevent injury when working at height Ensure that the device is always securely fastened with suitable hardware For elevated installations secure the device with suitable safety cables and always comply with relevant load dimensioning safety standards and requirements Overview The SGM G Spot model is a maintenance free multi environmental de B vice with an IP rating of 65 It has a powerful LED light source
Download Pdf Manuals
Related Search