USER MANUAL GUIDE DE L`UTILISATION MANUAL DE
Contents
1. without forcing pe 4 Prepare output connections 2 Measure and cut the hosing You will need a length of hosing that reaches 1 The remaining length of hosing will be used for output comfortably from the filter canister to inside the aquarium A Attach the hosing to the output connector OUT on the right side of the a Stretch out the hosing up to the top of the aquarium so it rests over the intake i AquaStop valve rim connector assembly a Push the factory finished end of the hosing onto the valve push it all the way b At a spot about 4 in 10 cm beyond the aquarium rim use a utility knife to cut as far as it will go the hosing Do not cut the hosing too short IMPORTANT You will want the hosing to be long enough so that its connection point with the intake assembly is always about 3 in 7 5 cm below the water line Remember you can always cut hosing shorter during final installation if necessary b Turn the lock nut counter clockwise until it is as tight as you can make it without forcing 2 Measure and cut the hosing Again you will need a length of hosing that reache2. Click gt to lock Prepare the Filter First disconnect AquaStop from filter and bring the filter to a sink making sure there are no soaps or chemicals which could contaminate the filter IMPORTANT The Bio Foam BIOMAX fine pads and carbon filter media supplied with your Fluval filter have been deliberately placed in Upper Mid and Lower level baskets to indicate their recommended placement for optimal basic filtration Be sure to note this positioning and place media in baskets at the same levels as you prepare the filter for use Remove the foam screen frame media cover and media baskets from the filter E canister The small white styrofoam square must be discarded As you remove Carbon wem eeng and BIOMAX from baskets note which levels they were packed in Then remove their outer wrappers do not remove carbon from porous bag s 2 Rinse baskets and media materials under running tap water to remove any dust and place media in baskets Or if you prefer select other media of your own choosing See Fluval Advanced Filtration for more information a 8 3 Place rinsed and filled media baskets back in canister and put the media cover back on top basket IMPORTANT Make certain that each kind of media is positioned at the same level it was packaged in unless you are deliberately choosing a different filtration plan than the recommended basic setup Never overfill baskets If baskets or c
3. b With inflammable or drinkable liquids This is a HOUSEHOLD APPLIANCE INTENDED FOR DOMESTIC USE and it is Suitable for INDOOR use only Do not install or store this appliance where it will be exposed to the weather or temperatures below freezing Make sure that this appliance is securely installed before operating it and that the electrical connection is in accordance with the data on the rating label Do not allow pump to run dry If an extension cord is necessary a cord with proper rating should be used A cord rated for less amperes or watts than the appliance rating may overheat Care should be taken to arrange the cord so that it will not be tripped over or pulled The connection should be carried out by a qualified electrical installer SAVE THESE INSTRUCTIONS for future reference To ensure optimal and proper functioning of your d IMPORTANT 06 series Fluval External Filter regular maintenance is required Failure to do so may result in the failure of the filter and will invalidate your warranty Additionally regular cleaning and maintenance will greatly reduce or completely COMPONENTS Magnetic Impeller amp Impeller Well Ceramic Shaft 4 Please refer to the maintenance schedule below Intake Stem Strainer Hosing Ribbed Hosing Primer Assembly with Primer Cover Gasket 2 AquaStop O ring Gaskets Foams in the foam screen P Bio Foam Polishing Pad Carbon BIOMAX 5 eum
4. and micro particulate Placing chemical filter media at the last stage of filtration will allow it to work best FLUVAL ADVANCED FILTRATION Lower level basket Media that continues the mechanical capture of small particles should be placed in the lowest media basket to ourify water and or remove particles before they can clog delicate pores of biological or chemical substrates The Bio Foam is ideal to remove small dirt particles that are not retained by the Foam Screen Frame In addition this foam provides a large surface to accommodate bacteria colonies providing an ideal environment for proliferation of beneficial bacteria and increasing the biological action of Fluval BIOMAX Mid Level Basket s The mid level basket is a good place to begin the biological reduction process A lot of media types provide both mechanical filtration and biological treatment creating an excellent environment for beneficial bacteria to proliferate With the primary mechanical purification of the water stream occurring in the Foam Screen Frame and the lower basket it is typical to load biological media as BIOMAX into the mid level basket Upper level basket This basket receives the clearest water making it the ideal place for dedicated chemical media Placed here Carbon for example efficiently removes discolorations medications and solubilized wastes that a mechanical screen cannot To increase the action of chemical fil
5. any air source an air stone an aeration device or the output valve Air entering the intake Strainer will diminish filter efficiency m 1 CO INSTALLATION AND USE INSTALLATION AND USE 3 Prepare intake connections 4 Clip the suction cup onto the intake assembly near the strainer and place the assembly in the tank making sure the strainer is at least 3 in 7 5 cm from the bottom If the tube is too long for the height of your aquarium remove the strainer from the intake assembly cut the tube with a hacksaw and then replace the strainer Once the intake assembly is properly positioned lock it in place by pressing the suction cups against the glass 1 Insert the AquaStop valve into the intake and output connectors on the cover and push down on the locking lever to lock it in place a Position the filter below the aquarium where it will sit while operating b Attach hosing to the intake connector IN on the AquaStop valve the input connector will be on your left c Push one end of the hosing onto the valve push it all the way as far as it will go 5 Position the top half of the rim connector assembly over the hosing and push down until it clicks to lock the hosing in place d Turn the lock nut counter clockwise until it is as tight as you can make it
6. bb prevent faults and reduction in performance MAINTENANCE FREQUENCY MONTHLY EVERY 3 MONTHS EVERY 6 MONTHS Check amp Clean Check amp Clean Check amp Clean Clean amp Lubricate Check amp Clean Clean amp Lubricate Clean amp Lubricate Check amp Clean Replace Clean Replace Replace Replace Rinse Replace Half Quantity Ensure Impeller Cover is fitted right way up when replacing Wet the seal ring with water before replacing Do NOT use petroleum jelly based products Pipes will gradually block with protein slime and waste Yearly replacement ensures optimal performance The rubber seal will perish over time and will lead to leaking of canister if not replaced Refer to Fluval 06 Media instructions Media needs replacing at different frequencies Only ever change 50 at a time YEARLY Replace Replace Check amp Clean Replace INTRODUCTION Fluval MultiStage Filters offer advanced pumping technology and a versatile combination of mechanical biological and chemical filtering capabilities This versatility enables you to customize your aquarium environment to meet the specialized needs of your unique collection of fish and aquatic plants Your filter comes with prepacked filter media that will work well for most basic aquarium setups However you have the option of selecting different media or alternative configurations of media if you wish Because you have so much flexibility in selecting and p
7. fluvalaquarium com General Guideline Location can determine function For example BIOMAX can act primarily as a screen for debris or act more as an environment for growth of beneficial bacteria depending on where it is placed in the filtration sequence Proper preparation is key Some materials such as Ammonia Remover require thorough rinsing so that their finest particles do not clog other modules or discharge into the aquarium For best results and the protection of your fish always read and follow the preparation instructions for the media you are using Use mechanical filter media in the first stage of filtration This helps ensure that the water will be as free of debris as possible when it flows through biological and or chemical filters which require clear water for maximum effectiveness To achieve maximum effectiveness Fluval 06 offers three types of mechanical filtration the white foam traps the larger particles the black foam traps smaller particles and the polishing pad removes the micro particulate Protect chemical media from debris Chemical filtering media modifies the chemical characteristics of the water by absorbing toxic compounds eg medicines odors and organic contaminants The filtration effectiveness of Fluval activated carbon for example is provided by its huge surface and contact with water up to 1000 m2 g Therefore it is necessary to prevent the chemical filter media from clogging by macro
8. out of its way Air will be expelled through the output nozzle causing the water in the aquarium to bubble To expel all the air in the system as quickly as possible the AquaStop valve must be fully open Be sure the lever is all the way down m I wech CN INSTALLATION AND USE 3 Once the bubbling in the tank stops you ll know the air is out of the system and the canister is full plug the power cord into an electrical outlet THE PUMP WILL START IMMEDIATELY Water should flow from the output nozzle continuously If it does not check your installation to be sure of the following e No kinks or loops in the hosing e The base of the canister is not more than 4 5 ft 1 4 m below the water level e The water is not more than 7 in 17 5 cm below the aquarium rim e The intake assembly is securely attached to the aquarium wall e No air is bubbling into the water at points where the intake assembly and the output nozzle connect to the hosing e No water is escaping from the hosing at the AquaStop valve connection points e The canister cover is securely closed e Both levers on the AquaStop valve are both pushed all the way down Continue pumping the instant prime handle until the unit starts to run on its own IMPORTANT To prevent damage e Never plug the filter in unless the canister is completely full of water Adjusting Water Flow Once the filter is operating continuously you can use the top lever on the Aqu
9. to lock it in place 7 Push down on the valve lever to open the AquaStop valve Water should start flowing immediately IMPORTANT If the hosing has been disconnected from the AquaStop valve or if the system has lost its vacuum for some other reason the canister will not fill automatically Use the instant prime handle to fill the canister 8 Allow the canister to fill completely then plug the power cord back into the electrical outlet IMPORTANT If the canister is not full before the filter is plugged in it may not work properly The filter unit should never be allowed to run dry Running the unit dry may result in damage to the motor m I CO MAINTENANCE Impeller Care The impeller well has an effective self cleaning feature However it is a recommended that you remove the impeller cover and inspect the impeller as part of your routine maintenance Keeping the impeller clean lengthens its life and the life of the motor IMPORTANT The impeller fan has a ceramic shaft which is resistant to wear and tear in use but is still fragile Handle carefully during maintenance 1 Remove the impeller cover Pull the tab over and gently pry off 2 If the impeller needs cleaning grasp the fan and draw it gently from the well Rinse it under clean water 3 If the well needs cleaning wipe gently with a Fluval Cleaning Brush 4 Replace the impeller in the well Slide the impeller cover tab into the tab receptacle on the rim of the
10. 106 206 USER MANUAL GUIDE DE L UTILISATION 206 406 MANUAL DE INSTRUCCIONES HAGEN www hagen com CANADA UK MALAYSIA Rolf C Hagen Inc Customer Service Department Rolf C Hagen Sea Sdn Bhd 20500 Trans Canada Hwy Rolf C Hagen UK Ltd Lot 14A Jalan 3A Kawasan Baie d Urf Qu bec H9X 0A2 California Drive Perusahaan Cheras Jaya Tel 514 457 0914 Whitwood Industrial Estate Balakong 43200 Cheras Selangor Castleford WF10 5QH Darul Ehsan USA West Yorkshire Tel 603 9074 2388 Rolf C Hagen USA Corp Tel 01977556622 305 Forbes Blvd SPAIN Mansfield MA 02048 FRANCE Rolf C Hagen Espa a S A Tel 800 724 2436 Rolf C Hagen France S A Avda de Beniparrell 11 y 13 Zone Parisud 4 P I L Altero 46460 Silla Boulevard Jean Monnet Valencia Spain F 77388 Combs la Ville Tel 34 96 120 09 45 Tel 33 1 64 88 14 18 GERMANY Hagen Deutschland GmbH amp Co KG Lehmweg 99 105 25488 Holm Tel 04103 960 0 Ver 26 11 NA AU Kam ch O D WN PRODUCT PARTS FLUVAL CANISTER FILTER Hosing Rim connector assemblies 2 Suction cups 4 Intake assembly with suction Output nozzle assembly AquaStop valve cup 7 Canister cover pump housing 8 Instant prime handle attached 9 Lift lock cla
11. 20112 A 20134 A 20174 A 20091 m Z I N FLUVAL 306 A 20121 A 20191 A 20123 A 20043 A 20067 A 20063 A 20061 A 20008 A 20011 A 15520 A 20026 A 15041 A 20001 A 20015 A 20059 A 20017 A 20021 A 20192 A 20039 A 20153 A 20154 A 20174 A 20092 FLUVAL 406 A 20121 A 20196 A 20123 A 20043 A 20067 A 20063 A 20061 A 20008 A 20011 A 15520 A 20026 A 1504 A 20001 A 20015 A 20059 A 20017 A 20021 A 20197 A 20039 A 20173 A 20154 A 20174 A 20093 Fluval 106 O Sr ve L IT nr ee an Fluval 306 See previous page for descriptions m N N Fluval 206 Tilt heijan Fr 29 y IT let de TTT Pr ir Fluval 406
12. aStop to regulate the water flow To reduce the water flow lift the lever up to halfway but no higher This can be done once the unit is fully operational and will not harm the motor However never run the filter with the lever up closed more than half way Air in the Filter Some air will become trapped in the canister as it fills air may also be released by new media Eventually the filter will expel all air pockets If you notice excessive bursts of bubbling over an extended period of time check all hosing and connections for air leaks Also make sure there is no air source such as an airstone or aeration device near the intake strainer m a A FLUVAL ADVANCED FILTRATION The Fluval stack of media baskets The stack of media baskets in the Fluval 06 series filters enables you to employ all three types of filtration in whatever configuration or sequence you determine is best to meet the needs of your aquarium environment Filtration always begins with a mechanical stage of waste particle removal as water flows through various foam screens and continues with subsequent biological and chemical stages as it flows up through the media in the baskets Because you can use the media of your choosing at each level you will able to design a system that provides additional mechanical biological and chemical filtration if you wish For detailed information as well as general guidelines for media selection please visit www
13. al aquatic specialist retailer for further advice before returning the product ps eee es FLUVAL EN 20 Rese MS Chan TATE Th ELIT M TU Er DETTE HM ve Ae ls Bart D iimg D A B c D F G H ER a pa pol CO GH Zz WH T WH L se lt x e REPLACEMENT PARTS Order replacement part from your Fluval dealer or by contacting Customer Service PARTS Rubber Feet Motor Head Foam Insert Frame Media Basket Media Basket Cover Gasket AquaStop Valve Intake Strainer Intake Stem with Intake Strainer Suction Cup 40mm with clip Aquarium Rim Connector Suction Cup 30mm Output Nozzle Ribbed Hosing Hose Lock Nuts Rubber Hose Connector Primer Assembly with primer Cover Filter Canister Ceramic Impeller Shaft amp Rubber Bushing Magnetic Impeller with Ceramic Shaft amp Rubber Bushing Impeller Cover Impeller Well Insert Motor Head Maintenance Kit Magnetic Impeller Ceramic Shaft amp Rubber Support Impeller Cover Gasket FLUVAL 106 A 20121 A 20181 A 20122 A 20046 A 20042 A 20038 A 20061 A 20007 A 20010 A 15520 A 20026 A 15041 A 20001 A 20014 A 20059 A 20016 A 20021 A 20182 A 20039 A 20112 A 20114 A 20174 A 20090 See following page for diagrams FLUVAL 206 A 20121 A 20186 A 20122 A 20046 A 20042 A 20038 A 20061 A 20007 A 20010 A 15520 A 20026 A 1504 A 20001 A 20014 A 20059 A 20016 A 20021 A 20187 A 20039 A
14. eceipt and 4 00 Return with dated receipt and 4 00 for postage and handling to for postage and handling to Rolf C Hagen Inc Consumer Repairs Service and Repair Rolf C Hagen USA Corp 20500 Trans Canada Hwy 305 Forbes Blvd Baie d Urf Qu bec H9X OA Mansfield MA 02048 For more information on our products please visit our website www hagen com I ET D anl Sen he wi THREE YEAR WARRANTY Fluval 06 Series External Filters are guaranteed against defects in material and workmanship under normal aquarium usage and service for 3 years from date of purchase Non replaceable and non serviceable parts will be repaired or replaced at Hagen s discretion free of charge when the complete filter is returned with all components along with a valid proof of purchase and postage paid This warranty does not apply to any filter that has been subject to misuse negligence or tampering It does not apply to filters which have been incorrectly assembled or unsuitably maintained or where installation and maintenance instructions have not been followed correctly The warranty does not apply to wear and tear parts such as the impeller impeller cover or motor seal No liability is assumed with respect to loss or damage to livestock or personal property irrespective of the cause thereof Before returning the filter under warranty terms please ensure that all setup and maintenance instructions have been followed If you are in doubt please contact your loc
15. ent Check with your local Environmental Agency for possible disposal instructions or take to an official council registered refuse collection point Electronic products not included in the selective sorting process are potentially dangerous for the environment and human health due to the presence of hazardous substances FES m I oO QUESTIONS If you have any queries or comments about the operation of this product please firstly refer to your set up and maintenance instructions Most issues can be resolved immediately with a little maintenance If you have any doubt or if you need replacement maintenance parts please contact your local aquatic specialist retailer for further advice If you wish to seek technical advice please call or write to us before returning the product under the warranty terms Most problems can be handled promptly with a phone call Or if you prefer you can contact us on our web site at www hagen com When you call or write please have all relevant information such as model number and or part numbers available as well as the nature of the problem CANADA USA CALL US TOLL FREE AT CALL US TOLL FREE AT 1 800 554 2436 1 800 724 2436 between 9 00 a m and 4 00 p m between 8 30 a m and 4 00 p m Eastern Standard Time Eastern Standard Time Ask for Customer Service Ask for Customer Service FOR AUTHORISED FOR AUTHORISED GUARANTEE GUARANTEE REPAIR SERVICE REPAIR SERVICE Return with dated r
16. es please read and follow these instructions for proper installation maintenance and use Failure to do so may result in loss of fish life and or damage to the filter SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE SYSTEM OVERVIEW The Fluval 06 Series filters offer several state of the art features to ensure reliable operation and trouble free maintenance Media is packed into filter baskets at the factory in the recommended positions for basic filtration in order to save you time and eliminate guesswork The instant prime system assures startup ease Plus to make maintenance quicker the AquaStop valve creates an air and watertight seal so you can disconnect hosing without breaking the vacuum that will be necessary to resume operation without priming For added convenience media baskets are self contained and interchangeable so that media can be rinsed or replaced in each one independently of the others The intake assembly siphons aquarium water and suspended debris in through Its clog proof strainer m Water flows down through the foam screen frame which traps large particulate matter The filter s new more powerful and silent pump then draws the water up from the base of the unit through the media baskets for the customized stages of mechanical chemical biological and fine mechanical filtration that have been designed through media choices and placement Filter media removes both waste particles and liquid impu
17. f the priming cylinder with clear water Be sure the cylinder has no debris trapped in the green flapper valve and It is sitting flush in a closed position mi I NI MAINTENANCE 2 Clean or replace media 1 Replace chemical media as needed Chemical media cannot be cleaned 2 Rinse biological media with aquarium water never tap water or replace as required Never replace all biological media at one time as valuable colonies of beneficial bacteria would be lost 3 Rinse screen foams and bio foams using aquarium or de chlorinated tap water or replace foams as needed For the most thorough cleaning possible slide the foam out of the screen frame and rinse each piece separately rinse and wipe the screen then reassemble Be sure that the foam is protruding from the top of the screen Rinse any other mechanical media also NEVER use soap or detergents on foam or screen as traces of cleaning products could harm fish 3 Reassemble unit DO NOT FILL CANISTER WITH WATER WHEN RE ASSEMBLING UNIT 1 Place rinsed and filled media baskets back in canister and put cover back on top basket 2 Replace foam screen in canister Insert with flat end down 3 Inspect and lubricate gasket as needed 4 Replace the cover making certain the MSF logo and power cord are properly aligned 5 Use the lock lift clamps to close the cover securely 6 Place the unit back in position re insert the AquaStop valve and push down the locking lever
18. impeller chamber Push down the opposite side of the impeller cover making sure the impeller starts to seat itself in the center of the impeller cover Continue to push down until the retailing tab clicks and locks into position NOTE The ceramic impeller shaft is held on the bottom of the impeller well by a rubber support The shaft can be easily extracted and reinserted by hand however pay close attention to be certain the rubber support does not become unseated Always replace the impeller cover to ensure proper alignment The impeller will wear out over time A replacement may be ordered from your local Fluval dealer or by contacting customer service at Rolf C Hagen Corp Replacing the Primer If the primer becomes damaged or worn and requires replacement remove the motor head from the filter case Snap off the primer handle by twisting sideways Once the handle is removed push the primer shaft down and remove the primer by grasping the plunger from the underside of the motor Insert the new shaft with the attached plunger snap the primer hand back onto the primer shaft and replace the primer cover locking it into the correct position with a click Recycling This product bears the selective sorting symbol for waste electrical and electronic equipment WEEE This means that this product must be handled pursuant to European Directive 2002 96 EC in order to be recycled or dismantled to minimize its impact on the environm
19. le m 4 1 N WARNING Close supervision is necessary when any appliance is used by or near children This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance To avoid injury do not touch moving parts or hot parts CAUTION Always unplug or disconnect all appliances in the aquarium from electricity supply before placing hands in water before putting on or taking off parts and while the equipment is being installed maintained or handled Grasp the plug and pull to disconnect Never yank cord to pull plug from outlet Always unplug an appliance from an outlet when not in use This appliance is not a submersible aquarium filter pump It is intended for use in ornamental household aquariums It may be used with fresh or salt water Maximum water temperature 35 C Do not use this appliance for other than intended use i e do not use inswimming pools bathrooms etc The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition and will invalidate your warranty Do not use this appliance a In swimming pools or other situations where people are immersed
20. mps attached 10 Impeller cover and cover gasket 11 Filter canister media baskets inside Refer to diagram on inside front cover MEDIA CONFIGURATION MEDIA Fluval BBOMAX Fluval Water Polishing Pad Fluval Carbon Fluval Bio Foam FLUVAL 106 1 1 1 FLUVAL 206 FLUVAL 306 FLUVAL 406 2 2 4 2 BEN WEEN Ie NO DD NO Refer to diagram on inside front cover Note sequence the media was packed in this is the recommended media placement CONTENTS Instructions in English EN 1 Instructions in French FR Instructions in Spanish ssh sers cud ES 1 O Fluval 106 T PACE ae ns AC ZE MCE LITE TE 4 p j ewer OG aT E Fluval 306 Ba d e _ Fluval 406 Ki Consulte las descripciones D en la p gina anterior m SR N N 8 O S T tre ALLLLLEL ETF PT IMPORTANT SAFETY INSTRUCTIONS WARNING To guard against injury basic safety precautions should be observed including the following READ amp FOLLOW ALL SAFETY INSTRUCTIONS and all the important notices on the appliance before using Failure to do so may result in the loss of fish life and or damage to the appliance 2 DANGER To avoid possible electric shock special care should be taken since water is employed in the use
21. of aquarium equipment For each of the following situations do not attempt repairs yourself return the appliance to an authorized service facility for service or discard the appliance A Ifthe appliance falls into the water DON T reach for it First unplug it and then retrieve it If electrical components of the appliance get wet unplug the appliance immediately B Carefully examine the appliance after installation It should not be plugged if there is water on parts not intended to be wet C Do not operate any appliance if it has a damaged cord or plug or if it is malfunctioning or it is dropped or damaged in any manner The power cord of this appliance cannot be replaced If the cord is damaged the appliance should be discarded Never cut the cord D To avoid the possibility of the appliance plug or receptacle getting wet position the appliance to one side of a wall mounted receptacle To prevent water from dripping onto the receptacle or plug a drip loop see photo should be arranged by the user in the cord connecting appliance to a receptacle The drip loop is that part of the cord below the level of the receptacle or the connector to prevent water travelling along the cord and coming in contact with the receptacle If the plug or receptacle does get wet DON T unplug the cord Disconnect the fuse or circuit breaker that supplies power to the appliance Then unplug and examine for presence of water in receptac
22. or setup and installation e Tools required Utility knife Note For an unusually shallow aquarium the intake tube may need to be cut this requires a hacksaw DO NOT PLUG IN FILTER UNTIL SETUP IS COMPLETE AND UNIT IS FILLED WITH WATER 1 Unpack and identify all parts Use the diagram on the inside front cover as a guide 2 Prepare the aquarium 1 Decide on filter placement Remember this is a gravity fed system For it to work properly all the Installation Requirements below must be adhered to MAX 7 in 17 5 cm Installation Requirements e The canister base must never be more than 4 5 ft 1 4 m below the water level e Hosing must follow a straight path from the filter to the aquarium rim with no loops and very little slack e The water level should never be more than 7 in 17 5 cm below your aquarium rim e The filter must ALWAYS be positioned below the aquarium e Intake tube should not be positioned in close proximity to an air source MAX 4 5 ft at 1 4 m 2 Place the two rim connector assemblies over the back top edge of the aquarium Place one just above the spot where you want to position the intake tube place the other just above the spot where you want to position the output nozzle Be sure the longer section of each connector is on the outside of the aquarium Attach suction cups to the outside and inside section of each connector IMPORTANT Be sure to position the intake tube away from
23. ositioning media you are able to control water characteristics with far greater precision than with traditional filters In addition Fluval 06 Series Filters provide more volume than would be possible with round canisters of the same outer dimensions Increased volume means a greater mass of filter material and a larger filtration area Fluval Filters multiply this advantage by directing water into complex flow paths for greatly increased contact with filtration media The result Maximum efficiency reduced maintenance requirements and the reliable flow of pure properly conditioned aquarium water Fluval Filters are designed and engineered for dependable performance and ease of use Features like click on rim connector assemblies for hosing and one step lift lock clamps on the canister make setup and routine maintenance quick and convenient Plus Fluval s proprietary AquaStop valve lets you disconnect then reconnect the hosing without compromising the system s vacuum seal This means you can stop the filter then restart it instantly without priming for quicker easier more convenient maintenance The superior performance and capability of this filter is backed by Fluval s well earned reputation for the best in fish and aquarium care and your assurance of the most up to date and reliable research in aqua care science For complete understanding of your Fluval Multi Stage Canister Filter and enjoyment of all its capabiliti
24. over are out of position cover may not close properly 4 Rinse both sides of the foam screen frame under tap water before initial use to remove any possible contaminants and slide it back into position in the canister flat end down If the screen does not seem to fit properly be sure it is not upside down I wech INSTALLATION AND USE Rubber Gasket 5 Complete canister cover assembly a Lay the canister cover on a flat surface with its topside down Remove the lubricated rubber gasket from its plastic bag To seal the cover opening properly the gasket must be moist but it need not be wet Carefully fit the gasket into the channel around the base of the cover b Slide the impeller cover tab into the tab receptacle on the rim of the impeller chamber Push down the opposite side of the impeller cover making sure the impeller starts to seat itself in the center of the impeller cover Continue to push down until the retailing tab clicks and locks into position 6 Place the cover on the canister Be sure to position it properly There is only one orientation possible Make certain that the MSF logo on the cover and canister is aligned and that the power cord fits into the notch on the rim of the canister 7 Lock the cover in place Push the double tabs of the lift lock clamps under the rim then press the upper tabs firmly against the cover DO NOT FILL CANISTER WITH WATER 8 Place the unit in its final po
25. pathways through the canister to give water more contact time with the media Pumping Power The more powerful the motor the faster it can work and the more water it can pump Each model in the Fluval 06 Series filters is powered by a motor engineered for top performance complete reliability and maximum efficiency with minimum noise Capacity Engineered Flow Rates Filter Areas amp Power Model recommendations to provide ideal filtration for aquarium tanks of various sizes AQUARIUM PUMP MECHANICAL Mele ey V i FILTRATION FILTER MAX WATER CAPACITY OUTPUT AREA VOLUME VOLUME CIRCULATION COLUMN HEIGHT U S L U S L Hr Sq mm U S L U S L U S L Hr Ft m Gal Gal Yds Qt Qt Gal 106 25 100 145 550 30 666 36 800 Jaa I S BCE 95 360 ALB 15 206 40 200 206 780 46 666 56 000 210 2 0 4 84 46 121 460 475 1 45 306 70 300 303 1150 46 666 56 000 3A Z 6 94 6 6 206 780 5750075 406 100 400 383 1450 63 583 76 300 442 42 8 94 8 5 245 930 7 38 2 25 Flow rates were measured with intake and output hoses that were the same length Filter pump electrical wattages FLUVAL 120 V 60 Hz 230 240 V 50 Hz FILTER ELECTRICAL ELECTRICAL MODEL SUPPLY SUPPLY 106 10 W 10 W 206 10 W 10 W 306 16 W 15 W 406 25 W 20 W EN 7 INSTALLATION AND USE IMPORTANT Read all instructions before beginning e For best results top off water in aquarium before beginning setup e Allow 30 45 minutes f
26. rities and can also be actively treated to change the water s chemical characteristics As water flows it brings oxygen into the system feeding beneficial bacteria and breaking down nitrogenous wastes After passing through all baskets purified water enters the impeller well to be pumped back into the output hosing As the output nozzle disburses the water it creates currents that help break down wastes All for a continuous flow of pure water custom treated for a healthy thriving aquarium environment A FLUVAL STATE OF THE ART TECHNOLOGY FLUVAL STATE OF THE ART TECHNOLOGY Media Baskets Our system of interchangeable media baskets is the key to Fluval s flexible filtration system Multiple modules allow a wide range of filter media options for maximum versatility Use the basic filtration media included or customize filtration by using your own combination of media in each basket Create the configuration that s just right for your system This unparalleled level of flexibility allows you to perfect your own aquatic environment AquaStop Valve Fluval s exclusive AquaStop valve offers unparalleled convenience and ease of use It creates an air and watertight seal that allows you to disconnect the hosing without breaking the vacuum that keeps air out of the line This means you can open the filter cover for routine maintenance and then start the system up again with no need for priming To stop the flow of water ins
27. s comfortably from the filter canister to inside the aquarium 3 Push the cut end of this intake hosing into the rubber connector on the a Stretch out the hosing so it rests over the output rim connector intake tube Push the hosing in by at least 1 in 2 5 cm without twisting it assembly b At a spot about 4 in 10 cm beyond the aquarium rim use a utility IMPORTANT knife to cut the hose Do not cut the hose too short Remember you can always cut it shorter during final installation if necessary IMPORTANT Remember to maintain a watertight seal the connection point between the hosing and the output nozzle should be kept below the water line e Hosing must follow a straight path with no kinks or loops and very little slack e If the hosing is too long the filter will not work properly e The factory finished end of the hosing must connect to the AquaStop valve e To ensure a watertight seal the cut end of the hosing which connects to the intake assembly must be kept under water mi I WO mi CH INSTALLATION AND USE 3 Push the cut end of this output hosing into the rubber connector at the top of the output nozzle assembly Push the hosing in by at least 1 in 2 5 cm without twisting it 4 Place the output nozzle in the tank about 0 8 in 2 cm below the water line then push the top half of the rim connector assembly down until it clicks to lock the hosing in place
28. sition IMPORTANT REMINDERS e This is a gravity fed system For it to work properly the filter must be positioned vertically below the aquarium e The distance between the bottom of the canister and the maximum water level must not exceed 4 5 ft 1 4 m e Hosing must follow a straight path from the filter to the aquarium rim with no loops and very little slack e If hosing is too long filter will not work properly e The water level should never be more than 7 in 17 5 cm below your aquarium rim e NEVER install the filter above the water level m I N INSTALLATION AND USE 9 Insert the AquaStop valve into the intake and output connectors on the cover and push down on the locking lever to lock it in place 10 Open the AquaStop valve by pushing the valve lever all the way down The valves must be fully open before the unit is turned on or primed 6 Start the filter SA 1 Check your installation E a Be sure lift lock clamps are securely closed b Make certain that the AquaStop valve is fully open and pushed all the way down c Check to see that the intake assembly and output nozzle are both fully submersed in water 2 Pump the instant prime handle by pulling it up and pushing it down several times until you hear water being drawn into the unit Return the instant prime handle to the down position As water flows through the intake hosing it will fill the canister pushing air
29. tantly and completely simply lift the AquaStop valve lever all the way up During filtration you can also use the AquaStop valve lever to regulate water flow without harming the motor or its components Motor Instant Prime System New and Improved The Fluval motor is hermetically sealed to ensure reliable operation It requires no coolant and can be placed in a closed cabinet No need for manual siphoning A simple pumping motion of the where airflow is restricted with no adverse impact on its performance or operating lifespan There are no moving parts except for Self Primer initiates water flow the impeller Foam Screen Frame The foam screen frame is vertically oriented and can be removed without having to remove the filter media baskets Containing two thick layers of replaceable foam blocks to provide a highly efficient initial stage of mechanical filtration The large surface area of the foam captures particulate waste which will be either be broken down or held This prevents clogging of biological and chemical media and enhances overall filter effectiveness Lift lock Clamps Securely lock cover in place Easy to open Intake Strainer The intake strainer has a clog proof wide mouth design to ensure steady rapid siphoning Output Nozzle Rim Connector Assemblies The output nozzle delivers a continuous flow of purified water By dispensing water in a The innovative rim connector assemblies slide on and snap together instantl
30. ter media and to prevent clogging from micro particulate it is suggested to use a Polishing pad just prior to the chemical media The fine filtration and chemical materials require more frequent maintenance than biological materials and their placement at the top makes it easier to wash and or replace without affecting the biological media MAINTENANCE WARNING ALWAYS DISCONNECT ALL APPLIANCES IN THE AQUARIUM FROM THE ELECTRICAL SUPPLY BEFORE PLACING HANDS IN THE WATER BEFORE PUTTING ON OR TAKING OFF PARTS AND WHENEVER THE FILTER EQUIPMENT IS BEING INSTALLED MAINTAINED OR HANDLED Media Care Filter Media must be periodically replaced or cleaned in accordance with instructions on individual packages Actual life span of any type of media will vary based on usage and the specific characteristics of each aquarium To remove and replace media follow the instructions below IMPORTANT Never replace all media at the same time Stagger filter media changes so that some older media remains in use This ensures re seeding of beneficial bacteria so that colonies discarded with old media will be replaced by vigorous new ones To enhance bacterial action use Nutrafin Cycle Biological Aquarium Supplement each time you change the media All rubber parts cover gasket primer stem AquaStop Valve and seal rings should be periodically lubricated 1 Drain the filter 1 Close the AquaStop valve by lifting the lever all the way up This seals off
31. the input and output hosing connections to maintain the vacuum that is necessary in order to restart the filter without priming 2 Unplug the power cord 3 Lift the locking lever to release the AquaStop valve It is not necessary to remove the hosing from the AquaStop valve unless the hosing the AquaStop valve or both require cleaning Periodic cleaning is recommended to ensure optimal water flow A good time to do this is during a major water change To clean rinse under running tap water if necessary use an appropriate Fluval Cleaning brush 4 Hold the unit by the canister not the cover and move it to an appropriate flat surface near a sink or other drain Be sure to keep it upright to avoid spills 5 Release the lift lock clamps then push down on clamps to lift the cover pump housing off the canister and set it aside 6 Holding the media cover in place tilt the canister over the sink or drain and pour out as much water as possible 7 Media and foam screen will be saturated with water If your sink is not large enough to hold them have appropriate bucket nearby Lift the foam screen media cover and media baskets out of the canister and place them in your sink or bucket 8 Rinse the interior of the canister with clear water NEVER use soap or detergents when cleaning canister or rinsing foam screen or media baskets Traces of cleaning products may remain on surfaces and damage sensitive fish tissues 9 Rinse the interior o
32. y for extra quick strong wide flow it creates an agitation effect that helps break down wastes and keeps setup They hold the intake and output hosing securely in place them in suspension until they can be siphoned away by the intake strainer The more solids that are kept afloat the fewer settle for cleaner healthier aquarium surfaces PUMPING POWER Flow Rates Fluval 06 series filters are available in four different models to accommodate aquariums of various sizes from the smallest home tank to the largest commercial setup They offer an outstanding array of filter choices for the hobbyist and professional aquarist alike The key to effective filtration is water circulation The more water filtered per hour the cleaner the aquarium will remain In addition water circulation is necessary to continually replenish the supply of oxygen in your aquarium The faster a filter can turn over an aquarium s contents completely filtering the entire volume of water in the tank the cleaner and more highly oxygenated the water will be Turnover rates are determined by a filter s volume and its flow rates Filter Area The greater the filter media volume the greater the mechanical efficiency and biological activity that will occur in the filtration process Fluval 06 Series filters have been designed to maximize canister volume in all four models and to accommodate multiple filter media options while at the same time increasing the
Download Pdf Manuals
Related Search