Home

Before You Use - Intellisystem Technologies S.r.l.

1. Standard set default size to standard Standardx2 set default size to standard x 2 Double set default size to double quality Medium lowest resolution of video Standard lower resolution of video Good normal setting of video Detailed higher resolution of video Excellent highest resolution of video 87 Intellisystem Technologies http www intellisystem it ye Intellisystem Image guality configuration URL IT210 User s Manual URL cgi bin image cgi NAME VALUE DESCRIPTION brightness lt 5 5 gt adjust brightness of image contrast lt 5 5 gt adjust contrast of image hue lt 5 5 gt adjust hue of image saturation lt 5 5 gt adjust saturation of image preview lt not required gt not save the parameters restore lt not required gt recall the original settings save lt not required gt save the parameters Camera control configuration URL URL cgi bin seriall cgi NAME VALUE DESCRIPTION interface RS232 switch COMI to RS232 lt other than RS232 gt switch COM1 to RS485 camctrl yes enable camera control no disable camera control baud lt integer gt set baud rate of COM1 data lt integer gt set data bits of COM1 stop 1 set 1 stop bit of COM1 2 lt other than 1 gt set 2 stop bits of COM1 parity None set parity check of COMI to none Odd set parity check of COMI to odd Even set pari
2. 15 user name for primary FTP server ftppass1 lt text string shorter than characters gt 15 password for primary FTP server ftpfolderl lt text string shorter than characters gt 40 upload folder in primary FTP server ftp2 lt domain name or IP address gt secondary FTP server ftpuser2 lt text string shorter than characters gt 15 user name for secondary FTP server ftppass2 _ lt text string shorter than characters gt 15 password for secondary FTP server ftpfolder2 lt text string shorter than 40 upload folder in secondary FTP server characters gt limit Not limited use full network bandwidth 128Kbits second use only 128Kbps of bandwidth 256Kbits second use only 256Kbps of bandwidth 512Kbits second use only 512Kbps of bandwidth 768Kbits second use only 768Kbps of bandwidth 1Mbits second use only 1Mbps of bandwidth 1 5Mbits second use only 1 5Mbps of bandwidth 2Mbits second use only 2Mbps of bandwidth Video configuration URL URL cgi bin video cgi NAME VALUE DESCRIPTION time lt not required gt enclose timestamp in channel 1 text lt text string shorter than 15 characters gt enclose caption in video channel Size Half set default size to half Halfx2 set default size to half x 2 86 Intellisystem Technologies http www intellisystem it Sve Intellisystem IT210 User s Manual
3. user may use demo as general user name and password is not reguired Regarding to the demo user account Allow camera control while demo can be limited to differ from managed users That will prevent demo user account from interfering with the normal operations 61 Intellisystem Technologies http www intellisystem it ye Intellisystem TECHNOLOGIES IT210 User s Manual Homepage layout settings J http 192 168 0 201 Microsoft internet Explorer ie lt Home Logo graph O blank default ure 1ttp l System G Users Logo link fret i Network Background graph O blank default O URL Po ee Font color White J l Camera control fe Modem Background color Black 3 5 Application Web page display mode Demo Image mode ib Homepage layout C Text mode View log file B View parameters l Factory default Administrators may give the IT210 Network Camera a different presence of homepage The Logo graph for the system logo in the upper left corner can be hidden or the default image from the system memory can be used or an external resource can be used by assigning a URL The Background graph is similar Default images from the system memory are quick to get but limited by memory size Images from external resources can be larger and more beautiful but will need more time to load If the background is skipped the background color will fill the browser window Administrat
4. video Camera control Modem Add user Application ain User name Homepage layout User password Add View log file View parameters Factory default S S R S S G 5 amp Delete user User name no user J Delete To change the administrator s password type the new password in both text boxes identically What is typed will be displayed as asterisks for security purposes After pressing Save the web browser will ask administrators for the new password for access To add a new user type the new user s name and password and press Add to insert the entry There are a total of twenty user accounts Since only administrators can change a user s password confirmation for user s password is not necessary 45 Intellisystem Technologies http www intellisystem it Sve Intellisystem ECHNOLOGIES IT210 User s Manual To delete a user pull down the user list to find the user name to be deleted and press Delete A message window will pop up for confirmation Network settings 3 http 192 168 0 201 Microsoft Internet Explorer co A AY A PA X id hip int 92 166 0 201 o P Reset network at next boot System General pesen 1P address 1521080203 8 Video Subnet mask Es 255 255 0 je Camera control Default router 19216005 Modem o Primary ONS server 192 168 0 1 Demo Secondary DNS server isos 1 1 8 Homepage l
5. 0 root Read only string 1 String shorter than 15 characters 2 The followings are as same as above 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 64 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual 19 20 lt user password gt 0 0002D1000001 Initial value is as same as serial number 1 String shorter than 15 characters 2 The followings are as same as above 3 4 5 6 7 8 O 10 11 12 13 14 15 16 17 18 19 20 LAYOUT lt layout type gt 0 text mode or 1 for image mode lt font color gt 1 color index 0 for black 1 for white 2 for green lt link color gt 3 for maroon 4 for olive 5 for navy 6 for purple 65 Intellisystem Technologies http www intellisystem it se Intellisystem 14 lt background color gt 0 lt logo type gt 1 lt background type gt 1 lt logo source gt http 80 lt background source gt http lt logo link gt http 80 lt com speedlink name gt O AT on of DAT bg ed 2 AT mode 3 bklt on 4 bklt off NETWORK lt install enabled gt YES lt ppp enabled gt YES lt ethernet address gt 00 02 D1 00 00 01 IT210 User s Manual 7 for gray 8 for yellow 9 for lime 10 for aqua 11 for fuchsia 12 for silver 13 for red 14 for blue 15 for teal 0 for blank 1
6. Intellisystem Technologies http www intellisystem it Se Intellisystem C Technical specifications Remote Management Configuration and system log can be accessed via Web browser and FTP application remotely Networking Protocol TCP IP HTTP SMTP FTP Telnet NTP DNS and DHCP Modem PPP dial up direct cable connection Physical 10baseT Ethernet or 100baseT Fast Ethernet Video Algorithm Supported MJPEG Features Adjustable image size and guality Time stamp and text overlay Resolution NTSC IT210 Up to 30 frames at 176x120 Up to 30 frames at 352X240 Up to 10 frames at 704X480 PAL IT210 Up to 25 frames at 176x144 Up to 25 frames at 352X288 Up to 10 frames at 704X576 Camera Specification 1 3 inch color CCD 512 H x 492 V NTSC 512 H x 582 V PAL 1 Lux F2 0 AGC AWB AI AES Electronic shutter 1 60 1 50 to 1 100 000 sec Standard C or CS mount lens fitting General I O 1 opto isolated sensor inputs max 12VDC 50mA 1 output relays max 24VDC 1A 125VAC 0 5A IT210 User s Manual Alarm Features Motion detection with percentage and sensitivity Daily repeat timing schedule 3 color images per camera for pre post alarm image storage Automatic transfer of stored images via email or FTP with event triggered actions RS232 RS485 9 pin D SUB RS232 or RS485 max 115 2Kbps PAN TILT PT positioning device control through RS232 or RS485 Clear data command driver is supported Remote S
7. VIE WINE syst m ParAaMElers s s siceccicsescccscesceapeasecstaqeescedscsesiasns RERA TAERAA AE a aa E EEEE a 73 Restore factory default Settings v vussssssssisik enaa a n en a a a a ae Ka a Ka aan anananeean 73 Clear data path for proprietary commands 0 0 ee ee ee e n a a ae a a a na Kaanaa anaean 73 Uploading snapshots periodically to an external FTP server cuuuuuussn unen na eee eeaeee 74 Viewing and downloading the stored snapshots seososssss e a a a aa e aa na naa aeen 74 2 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Downloading the update snapshots ces eeeeseeseeseeeeneceseeeeeeseeeseeeseeeaeeeceseeeeaeeeeeesseeeaeseeeeaeenes 74 Customizing images of homepage vuuuussmn nana n ana a nan a a n a an a Ka Kaa na na na Kaan anaean 75 MIG WINE System 106 7 osto roserne toa TEA LAKAT AKA Lana UL LA TTL TUN LAVA Eki TE EEE TESSE ETETEA ES Hha 75 Uploading the configuration file uoossssssssui an aa en n en a rek a na Kaa a Ta Ka aan anaean 75 Software revision Upgrade oo ee cece cece cee cee sanaakaan enaa ana aa Eror a rrer P ESE Eri Sepaea separere rts 76 System core AebugpihSmmmmssssssavsva muu EEEE E EEEE NAKATAA NESTEEN EEEE EREE KE SAKANEAN EKEREN TI Monitor changed status of digital inputs suossssssaa e a a ana aan n aan aa na Kanaan ae aaneen 77 Stop nkormation Aumping sass assa een er a es
8. 10 100 socket Connect to Ethernet network with a UTP category 5 cable that cannot exceed 100 meters Once the Ethernet cable is connected without error the IT210 Network Camera will utilize Ethernet interface regardless of modem connection COM port This RS232 serial port can connect with a modem or included null modem cable to utilize dial up network when Ethernet is not available If the IT210 Network Camera operates with Ethernet interface administrators may use this port to control the attached PT positioning device Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual General I O terminal block jeej 65432 1 1 lt DH INPUT Max 50mA 12VDC 2 lt DI INPUT 3 lt SW COMMON OUTPUT short with NC at initial state 4 lt SW NOPEN OUTPUT Max 1A 24VDC or 0 5A 125VAC 3 lt RS485B inverting 6 lt RS485A non inverting The IT210 Network Camera provides a very flexible general I O interface to combine with the user s security devices such as sensors alarms lighting or door locks The general I O terminal block has six pins for device control These pins can be divided into two categories based on their functions including RS485 and digital inputs and outputs If the device connected to COM has an RS485 interface wire two control lines to pin 5 and pin 6 After switching to RS485 on the configuration page the PT control commands will be directed throu
9. IP address to invite the new IT210 Network Camera If it replies that means the IT210 Network Camera has accepted the assigned IP address and is ready for access The first several ping reguests may fail during the self configuration period of the IT210 Network Camera Since the accurate grammar of ARP and PING depends on the operating system refer to its related help manual 19 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual First access to the IT210 Network Camera When connecting to the IT210 Network Camera for the first time administrators should check users and network settings on the configuration page For complete protection from illegal usage the IT210 Network Camera provides three privileges and always needs user name and password before access The lowest level is DEMO mode whose services are subject to administrator s permission The standard level is the USER mode that consists of twenty user profiles Each user is able to access the IT210 Network Camera except for system configuration The twenty user profiles are also maintained by the administrator The highest level is ROOT mode that only opens to administrators for initial setup system configuration users administration and software upgrade The user name of the administrator is internally assigned to root When connecting to the IT210 Network Camera users will be reguested for user name and passwor
10. a ae aa a Ka nananana 89 Modem configuration URL cece eee cee kan ekana aka a aa ka ae aa a a a naene annan 89 Application configuration URL sissasssssvis saa vantaan er nn muka nana kasassa sissa sy ananas s aasia 90 Motion detection configuration URL ccuossssssssssssssses seikan a ae aa a naa a na an aa nananana 90 Demo configuration URLs ava ua ara makv A VNS K LKKA AUKKO KSK EKSE STN TU KUVA AUS y aasian 91 Homepage layout configuration URL 0 0 saakaan ene a a n a na a Ka Kaa na aa an aan aeaean 91 APpEendiX cessisceuatsscucenssasaveanssssanoessacsensnsoadsavchscsssnvensedicatensesvedccussetenceiscase DD As POST Pprocotumt mmavmassnsvavmaneaaas kake vanvokk uvuu aak vaaa kka uu osoro kua u SAN one 2 B Frequently asked questions eeo0ooa noa a a a aa eaa 0 anoo 000000 J C Technical specifications vu omassssraa vaasa asen JO Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Before You Use Surveillance devices may be prohibited by law in your country Though the IT210 Network Camera is not only a high performance surveillance system but also a networked video server ensure that the operation of such devices are legal before installing this unit for surveillance It is important to carefully check the contents with the Package Contents section after opening the package Understanding the physical description can prevent damage caused by abnormal usage and
11. also remember to choose Network option to enter mail server address and recipient s e mail address If Dialout allowed is not checked The IT210 Network Camera will not send out any snapshots when events occur and the settings except for Initial modem command in this page will have no effect The system will preset the attached modem to eliminate echo and mute line sound To initialize the modem with further commands type into the edit box The prefix AT should be included Administrators should choose an appropriate Dial Method according to the local POTS environment An incorrect dialing prefix may cause the IT210 Network Camera to fail when dialing 55 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual out Redial attempts means how many times the IT210 Network Camera should try to connect to each ISP Setting the value in Disconnect after minutes will force the IT210 Network Camera to drop the connection when there is no activity on the connection for the specific period The range of this period is from 1 to 240 minutes with 0 indicating a continuous connection Administrators may let the IT210 Network Camera keep the connection for a while to allow connections from outside The IP address given by the ISP can be taken from the connection log that is mailed or uploaded when dial up connection is successful Setting the value to zero will make the IT210 Network Camera always
12. erase image will clear all snapshots saved in memory Erase logo and graphic buttons Typing erase graph will clear all images used on the homepage If no new images are uploaded the system will switch to text mode and use default images instead Skip installation at next boot Typing lock will inform the IT210 Network Camera to fix current network settings It need not wait for installation during the next boot Reset network for new settings Typing unlock will make the IT210 Network Camera give up current settings and wait for installation Restore factory default settings Typing clear will make the IT210 Network Camera restore factory settings but not restart To validate new settings type reset to make the system restart Reset system Typing reset will make the IT210 Network Camera perform a software reset 78 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual URL commands of the IT210 Network Camera For some customers who already have their own web site or web control application the IT210 Network Camera can be easily integrated through convenient URL This section lists the commands in URL format corresponding to the basic functions of the IT210 Network Camera Some RFC standards related to HTML may be a good reference for implementation of the customized homepage Capture update Snapshot of video channel cgi bin video jpg Display images Selec
13. existing networks Some broadband service subnet mask may differ from the default value 255 255 255 0 and service providers may assign some specific network settings Administrators should change the configuration according to what is given by the service provider The configuration may include IP address Subnet mask Default router Primary DNS server and Secondary DNS server After changing network settings be sure to leave Reset network at next boot blank to skip next installation when the system restarts Otherwise the settings will be erased Each IT210 Network Camera can be limited in bandwidth by administrators according to its priority and importance of location Bandwidth limit is most useful to balance network utilization when multiple IT210 Network Cameras are installed in the same network It is more effective than changing image guality only and achieves better performance with adeguate image size and guality Keeping the value as zero means no limitation on bandwidth utilization For security or network integration administrators also can hide the server from the general HTTP port by changing HTTP port to other than 80 Local FTP server port can also be changed to other than default port number 21 Administrators should have enough network knowledge to change the default port The IT210Network Camera not only plays the role of server it will also actively connect to servers outside to send out messages or sn
14. for default image or 2 for loading from URL 0 for blank 1 for default image or 2 for loading from URL link to external resource when logo type is 2 no longer than link when background type is 2 no longer than 80 providing external link when clicking on logo no longer than no longer than 8 characters no longer than 8 characters no longer than 8 characters no longer than 8 characters no longer than 8 characters or NO obsolete Read only string 66 Intellisystem Technologies http www intellisystem it se Intellisystem lt host ip gt 192 168 0 201 lt subnet mask gt 255 255 255 0 lt gateway ip gt 192 168 0 254 lt primary name server gt 192 168 0 1 lt secondary name server gt 168 95 1 1 lt ntp enabled gt YES lt network timing server gt ntp cup external hp com lt smtp mail server gt lt mail recipient address gt lt mail return address gt lt backup smtp mail server gt lt backup mail recipient address gt lt ftp server port gt 21 lt ftp server gt lt ftp username gt lt ftp password gt IT210 User s Manual Standard IP format Standard IP format Standard IP format Standard IP format Standard IP format or NO Standard IP format or string shorter than 40 characters Standard IP format or string shorter than 40 characters String shorter than 80 characters String shorter than 80 characters Standard IP format or string shorter tha
15. found on the labels under the body of the IT210 Network Camera and the top side of the carton The primary users will be allowed to enter as soon as the administrator finishes adding user profiles Upon successful authentication the main page will be displayed For demonstration purpose enter the Demo page of configurations to activate the demo account Once the demo account is setup any one may watch the video by using demo as user name while ignoring the password Different from managed users the demo account has certain limitations that 35 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manual are determined by administrators In the figure below the foreground is the login window and the background shows the message when authentication fails The user may check the option to save the password for future convenience Jito 1192 168 0 201 Microsoft internet Explorer Protected Object 5 The odyeet on the perver u protected If it is initial access to the IT210 Network Camera in Windows the Internet Explorer will ask to install a new plug in that is provided by the IT210 Network Camera This plug in has been registered for certificate and is used to display motioned pictures in the Internet Explorer Users may click on Xe to install the plug in If the web browser does not allow the user to install check the security option to l
16. in Flash memory and restart automatically When IT210 Network Camera starts writing firmware both status LED indicators will stay on until system restarts It takes about 30 to 40 seconds User must keep the power stable during the update process After the system restarts IT210 Network Camera may need installation depending on whether the Reset network at next boot option is enabled or not After IT210 Network Camera boots up reload the web page in the browser If power fails during the software upgrade the program in the memory of the IT210 Network Camera may be destroyed permanently If the IT210 Network Camera cannot restart properly ask the dealer for technical service 76 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Telnet The IT210 Network Camera has a Telnet daemon for only administrators to access some seldom used functions Using any general terminal program to connect to the IT210 Network Camera will prompt the user for a password Username is not reguested here since only administrators can access the Telnet daemon The password is as same as that used in web access After logging in type help for the command list If debug or dinote is not executed Telnet will disconnect automatically after being idle for 1 minute System core debugging General activities are recorded into SYSTEM LOG continuously but information about abnormal status is not
17. installing the IT210 Network Camera Auto Iris Lens Connector If the auto iris lens is used AES on rear panel must be turned OFF And you also have to select VIDEO Drive or DC Drive lens by the switch The pin assignment of the auto iris lens connector is as follows l 3 VIDEO Drive DC Drive Pin 1 Power source Damp Pin 2 Video signal Damp 2 4 Pin 3 Not used Driver Pin 4 Ground Shield Driver 10 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual How to Install To easily fit into various environments the IT210 Network Camera automatically detects the attached interfaces and configures itself to the best condition Therefore users need not care how to select the network between Ethernet and modem and whether the Ethernet speed is 10Mbps or 100 Mbps The high performance built in CCD and lens always give users delicate image guality The IT210 Network Camera supports Ethernet and modem interfaces according to the user s existing network Ethernet can provide higher bandwidth to achieve the best performance while dial up network with modem is more common in current Internet applications Refer to the related installation section for your network environment If both interfaces are available Ethernet is recommended and will be chosen as the first priority if Ethernet cable and modem are concurrently attached Managing to install in the other interface
18. intellisystem it Se Intellisystem IT210 User s Manual Customizing images of homepage If any necessary image is lost while homepage layout is image mode the IT210 Network Camera will switch to text mode automatically While in text mode there is a small icon before each link that can be changed by administrators When choosing homepage layout in image mode administrators may change the look of logo background and image buttons by self There are three types for logo and background blank default and other URL The default method will use the image stored in Flash memory Administrators may change the default logo background image and button images by uploading customized ones The followings are the referenced file name and size limitation Object File name Maximal size Logo logo gif Logo and background share 8000 bytes Background back gif Logo and background share 8000 bytes Link icon btn_text gif 2000 bytes Configuration btn_conf gif 5000 bytes Viewing system log Download SYSTEM LOG and open it with any text viewer The content of the file reveals useful information about configuration and connections after the system boots up It helps administrators easily find out who and how to access the IT210 since all network access to the IT210 Network Camera is recorded with timestamp The system log is scrolled to keep the newest messages Uploading the configuration file To update each IT210 N
19. keep the connection Based on the settings of DI DO in the application the system will send mails or upload via FTP with image attachment upon the event occurring In that case the IT210 Network Camera will need a network connection and automatically dial out to the pre configured server outside When a connection is successfully established the IT210 Network Camera will send out a connection log to notify given network settings For those installations that may switch the network interface between Ethernet and PPP administrators should notice that the settings of FTP or SMTP servers might be different from what are in an Ethernet environment If the network interface is changed administrators may need to configure them in advance The IT210 Network Camera will try the second ISP as a backup when the first ISP fails and exceeds the redial attempts ISP phone number should be the complete phone number including country code and area code if necessary Login username and Login password are used to pass the PPP negotiation requested by the ISP server Note that the pair of login name and password is dependent on the ISP and is different from what is used in the authentication process in web access 56 Intellisystem Technologies http www intellisystem it TECHNOLOGIES ye Intellisystem IT210 User s Manual Application FJ http 192 168 0 201 Microsoft internet Explorer 0 0 Ala a BIB g Application D Ev
20. lt PT control commands gt HOME UP IT210 User s Manual among 5 and 5 among 5 and 5 0 1 representing disable enable camera control or RS485 String shorter than 80 characters String shorter than 80 characters String shorter than 80 characters String shorter than 80 characters String shorter than 80 characters String shorter than 80 characters String shorter than 80 characters 69 Intellisystem Technologies http www intellisystem it se Intellisystem DOWN LEFT RIGHT ALERT lt snapshot channel enabled gt 0 YES lt application mode gt 0 event lt visual alert gt NO lt upload method gt 0 lt file with time suffix gt YES IT210 User s Manual String shorter than 80 characters String shorter than 80 characters String shorter than 80 characters or NO for none 1 for seguential mode 2 for motion event 4 for I O or YES to show alert in image 0 for FTP 1 for email or NO lt tenth seconds to snapshot after event gt 0 lt percentage of object size over screen gt 10 lt percentage of sensitivity gt 95 0 100 but O and 100 will make no sense 0 100 but O and 100 will make no sense lt tenth seconds to snapshot periodically gt 0 lt time to start snapshot gt 00 00 00 lt time to stop snapshot gt 00 00 00 24 hours format 24 hours format 70 Intellisystem Technologies http www intellisystem it se Intel
21. reduce most problems during installation Basically the IT210 Network Camera is a network device and should be easy to use for those who already have basic network knowledge If there is a system error and it does not recover easily due to erroneous configuration check the section Auxiliary buttons to restore factory default settings and run installation again The IT210 Network Camera has been designed for various environments and can be used to build various applications for general security or demonstration purposes For standard applications read System configuration to understand all functions To make best use of the IT210 Network Camera review Advanced functions to get creative ideas To those professional developers URL Commands of the IT210 Network Camera will be a very helpful reference Those paragraphs preceding by N should be fully understood and cautioned Ignoring the warnings may result in serious hazards Intellisystem Technologies http www intellisystem it ECHNOLOGIES e Intellisystem IT210 User s Manual Package Contents Network Camera IT210 Power adapter Null modem cable I O terminal block connector Wrench Installation and document CD Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Physical Description Rear Panel IBD eesu HALO wos AST DE a 16 2 s PT scanner Ethernet
22. server upon special events Otherwise it will wait permanently for the user s call to establish a network connection to provide services In the following content dial in connection denotes a passive IT210 Network Camera waiting for a phone call to establish a point to point connection Dial out connection denotes an active IT210 Network Camera to dial out to the other end of a dial up server or any Internet service provider abbreviated as ISP to reguest a point to point connection 22 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Cable connection IIVI ZETSY AVO owog Shut down the peripheral devices prior to connection Connect the supplied cables from the IT210 Network Camera to the related devices according to the above diagram Note that power adaptor must be kept unplugged until other cables are firmly connected For the first access to the IT210 Network Camera without Ethernet administrators may use the included null modem cable to connect to COM for direct connection It is also convenient for administrators to access the IT210 Network Camera through the null modem cable directly without modem or Ethernet card After necessary information is entered a modem can be used to dial into the Internet Power on Make sure all cables are correctly and firmly connected Turn on cameras sensors alarm devices and then finally attach power adaptor of the IT210 Network Cam
23. the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the seperation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits Europe This digital equipment fulfills the requirement for radiated emission according to limit B of EN55022 1998 and the requirement for immunity according to EN50082 1 1992 Liability Intellisystem Technologies S r l cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice Intellisystem Technologies S r l makes no warranty of any kind with regard to the material contained within this document including but 97 Intellisystem Technologies http www intellisystem it yo Intellisystem IT210 User s Manual not limited to the implied warranties of merchantability and fitness for a particular purpose All other company names and products are trademark or registered trademarks of their respective companies For any question and support please contact Intellisystem Technologies S r l Support info intellisystem it Web Site http www intellisystem it 98 Intellisystem Technolog
24. the time disable the install option if this IP address is already reserved for this IT210 Network Camera Clearing this option will skip the installation procedure during the next power up and use the previous settings If the install option stays checked the IT210 Network Camera will perform the installation procedure every time the system boots up Details about configurations are described in the How to Use section Related figures are attached for easy reference 21 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Modem Environment Hardware installation Before installing the IT210 Network Camera the administrator should memorize the serial numbers on the packages respectively for the initial passwords To use a dial up network the Ethernet socket should be left disconnected since Ethernet is the first priority among available interfaces After powering up the IT210 Network Camera will detect if any external modem is connected to the modem port Once a modem is detected the heartbeat LED will flash periodically If no modem responds the IT210 Network Camera will assume the included null modem cable is connected to perform system configuration Then both LEDs under the power LED will turn on until null modem connection is established If users have setup a remote dialup server or subscribed to an ISP service the IT210 Network Camera can be configured to dial to the
25. ty maata Na e ona min OON sakan mas brase cette gy Seem ts the inben Fores snai Bo Gente w to we basn O irma neei katui tora sum eere LIDIO merecem omset Chet Oe mp ess mm Mat erort Paphoree 0 000000000 what 19 00 ratr ym 1000 ro eet et mika art mie De ok 4 Ow ho Pantha ee 64 hkoomat Npteme 0 he 49 00 h sma te te Dart cotter end chew tiep te SA JA BT 14 44 14907 14 o het te PP bem tater te try ether we Lavat feud mar van ot bee bere teat teen After successful authentication administrators should see the motion pictures in the main page When using Microsoft Internet Explorer administrators should allow a plug in provided by the IT210 Network Camera to install additionally For best security administrators must change the password on the system page of configuration immediately After changing the password the browser will display the authentication window again to ask for new password Note that the new password will also be used in the next dial up 33 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual To make the IT210 Network Camera successfully work in dial in and dial out modes follow the procedures below for basic configurations If people other than administrators will be allowed to use the IT210 Network Camera administrators should add these user profiles in the users option While the IT210 Network Camera accepts dial in connection and ac
26. v Rowcrtwe Ocun amp hien AN ke 172 16 10 00 74 MP nelisysen IT210 Network Camera Quality Nedum Standard Grod Detaled Excelent Gizer Hak Hat x 2 Standard Standard x 2 Double e 38 Intellisystem Technologies http www intellisystem it sy Intellisystem ECHNOLOGIES IT210 User s Manual o 3 b tp M1 72 16 10 37 747 Micresett Imernet Explorer Fe Make Vosmi Prati Suuri gt Orea O AAG Pera Jori Ares Wen tradi BB E Calegari Googe vi Pcrardeb Gerani X iaa mai Peerage GC hies KE htn 16100 Ou amp MP inelisysen 1T210 Network Camera Qualys Nedam Standend Good Detaded Excelent gaaei Size Mak Hatt x 2 Standard Standard x 2 Osuble Close Configuration 39 Intellisystem Technologies http www intellisystem it TECHNOLOGIES Sve Intellisystem IT210 User s Manual Video quality selection It allows users to adjust the video quality for speed or smoothness The performance is also subject to the network bandwidth and number of users Five options are available to be chosen from medium to excellent Medium quality means the picture has the quickest refresh rate but the worst image quality and Excellent quality means the picture has the slowest refresh rate but the best image quality Fle Modfca vasis Peirt Suet 7 Qrim Q BO Poe fermen nn Google unwed Oceanis X bnan E vetpf 172 16
27. will automatically clear the previous network settings to start new installation In the following content user refers to those who can access the IT210 Network Camera and administrator means the supervisor who has the root password to configure the IT210 Network Camera in addition to general access Administrators should carefully read this manual especially during installation 11 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Ethernet Environment Hardware installation Before installing multiple IT210 Network Cameras at the well chosen locations the administrator should memorize the serial numbers on the packages respectively for future use Cable connection a E i Er Wo Power Supply ABD 20254 ALI wes PT scanner Shut down all the peripheral devices prior to connection Connect the supplied cables from the IT210 Network Camera to related devices according to the above diagram Note that the power adaptor must be kept unplugged until other cables are firmly connected 12 Intellisystem Technologies http www intellisystem it ye Intellisystem IT210 User s Manual Power on Make sure all cables are correctly and firmly connected before turning on the IT210 Network Camera Turn on cameras sensors alarm devices and then attach the power adaptor of the IT210 Network Camera to the electric power socket After
28. will the IT210 Network Camera check the status of digital inputs A The IT210 Network Camera will check input status in less than half a second However to avoid repeatedly checking conditions too often and to allow the devices connected to digital outputs to function properly the IT210 Network Camera will delay 3 seconds by default after each condition matches Users may change it according to specific applications During this period any condition will be ignored Q If I set the IT210 Network Camera to send e mails of images whenever the conditions are met will my e mail account overflow A It is recommended to use transient state rather than steady state For instance use and V instead of H and L to let the condition be triggered only when state is changed Q Why can I not access the IT210 Network Camera when I setup some options in the application A When the IT210 Network Camera is triggered by events snapshots will take more time to write them into memory and take further action like email or FTP If the events occur too often the system will always be busy with sending images That will make users feel like the system responding too slowly If it is in sequential mode the uploading speed depends on the network utilization server performance and how many users are accessing the video Once the system is too busy to configure use the restore factory default and reset button to save the system 95
29. 10 0174 Size Half Half x 2 Standard standard x 2 Double 40 Intellisystem Technologies http www intellisystem it ECHNOLOGIES sy Intellisystem IT210 User s Manual Video size selection It allows users to adjust the image size with consideration of bandwidth and visual effect Five options are available including Half Halfx2 Standard Standardx2 and Double Halfx2 consumes the same bandwidth as Half but has the same size with Standard Of course the visual effect is worse than Standard Standardx2 compared to Double is similar to the case Halfx2 is especially suits in the low bandwidth environment like a dial up network To fit into the small image area timestamp will be skipped in Half and Halfx2 modes e tegnet v Pcoanwd unis Corca mmagni S2Cercare que GC OES TACE ETE v D E A Intellisystem IT210 Network Camera Quolity Medium Standard Good Detailed Excellent ee c Close Size Half Half 2 Standard Standard x 2 Double 41 Intellisystem Technologies http www intellisystem it ECHNOLOGIES sy Intellisystem IT210 User s Manual Pan Tilt positioning device control An external PT positioning device may connect to bear the IT210 Network Camera with motion capability If the camera control option has been enabled there is a control panel to the r
30. 600 bps Modem and click on Net Install New Modem q Standard 14400 bps Modem K Accton Technology Corpor i aj Choose the serial port that the included null modem cable is attached to and click on eS The 25 Intellisystem Technologies http www intellisystem it TECHNOLOGIES se Intellisystem IT210 User s Manual null modem is now ready for use Install New Modem Install New Modem If no Dial Up adapter exists in the system Windows may automatically prompt to install Press ox to continue If it does not start automatically double click the network icon in control panel to install Microsoft dial up adapter 26 Intellisystem Technologies http www intellisystem it se Intellisystem ere IT210 User s Manual Fa Dial Up Networking ei 27 O Setup a new connection After the 33600 bps modem is installed open the dialup network folder in Windows to build a new Fa Dial Up Networking Make New Connection The Make New Connection wizard walks you step by step through adding Dial Up Networking connections Just follow the instructions on each screen 27 Intellisystem Technologies http www intellisystem it TECHNOLOGIES se Intellisystem IT210 User s Manual Select the device as the newly installed standard 33600 bps modem and click on Mem Make New Connection Standard 33600 bps Modem N Just enter arbitrary digits as phone numb
31. EEE nss E E TI Query status of digital Inputs vouoenoe taan kama a ar nn a aan ana m ad na nona nona asuma aE 78 Set ATSITAlOUTDULS n osiensa cedssvcssccensessoscossonsosadesncnsndesodesssotseesoesostevegstaveesseoscuvesvesseesiag SLA AA 78 Erase snapshots stored in Flash memory oouisssssiisi aan en n a a a na naa a Ta Ka aan anaeen 78 Erase logo and graphic DUttONS cece cece ekee en n en a a ae a naa a Ta Kanaan anaean 78 Skip installation at next DOOU rrise roen EE E AAA KU KUSEE ESSO KSS KES UKKO TVK KUKI KANE SeA 78 Reset network for New SettiheS vssusmutstea uussa P rE ESEE ana ka ara NE NOKKAA Mn EE aka nat 78 Restore factory default settings s issmvss akame nana asa NEEE SEENE PEPEN REENEN EENES 78 Reset Syste Msisi E E EEE aan UA ULA enaa da vnT A 78 URL commands of the IT210 Network Camera e ssessesessesesesesosoesesossesesosoeeese 7 9 Capture update Snapshot of video channel ssssssessssssseserssrsrsssrsststesssesessestnernrseesrsrereseneesene 79 Display UMAGES ge N A EET 79 Get stored snapshots from Flash memory esssssssssessissssssesrssrsrsrsrnrrnsisrsrsrisinisrrnrnrnnrnrnrnseeenene 81 Move positioning device in PT direction sesesssesessessisssssererisrsrsrnsesrisrsrnrrernrsrsrnrnrnresrsrsenees 81 Query status of digital inputs s ssessesessesssesetstsseseserstststssesrsrsrsrsteressrntnesesstntneeneneesrnrnreseneenene 81 Drive igitalOutputs cides v cscccscssiesccuetacetscctedac
32. HNOLOGIES sy Intellisystem IT210 User s Manual snapshots might be not important but alert in image may help verify occurring events tee ee ee eee T Geer enttial made tapaat even fi heres soon puos tegn 73000 Ihe ams meor ont EE Pere n C Send iaagshat Dy mal send vaonstot dy FTP EFT Me nome men one and trre pah The IT210 Network Camera is able to monitor the video signal if the objects in the image are moved To use motion detection check Upload snapshot while motion detected and then click on __GaafigweMotonDeecion to tune Object size and Sensitivity to reduce the false alarm The larger object size and lower sensitivity will make the IT210 Network Camera ignore small variations in images To configure DI DO there are four extended I O scripts Motion detection can be considered here to drive digital outputs The format will explain below and no space is needed among each parameters It also applies to CONFIGINI when using FTP 59 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual lt command format gt Digital input number Digital input state operator Digital input number Digital input state operator hour minute second operator M Digital output number Digital output state lt parameter explanation gt Item between and means optional
33. J A AI 918 4 p hp N 92 168 0 201 J System Host name Msuaiserver System 5 Users Network Date and time je Video C Keep current date and time E ahaa control Sync with computer time loi E Application PC date 2001 10 18 yyyy mmidd Demo PC time 2052 37 hh mm ss i Homepage layout e S View log file ee 5 View parameters Date 2001 10 18 yyyy mm dd Factory default Time 20 52 20 hh mm ss Automatic NTP server xo to invoke default server Time zone GMT 8 00 lt url gt http lt IT210 Network Camera gt setup config html lt IT210 Network Camera gt is the domain name or original IP address of the IT210 Network Camera 43 Intellisystem Technologies http www intellisystem it ECHNOLOGIES sy Intellisystem IT210 User s Manual System parameters TY http 192 168 0 201 Microsoft Internet Explorer fx B A R a lt fe A http 92 168 0 201 o ystem Host name MsualServer js System 5 Users Network Date and time Video C Keep current date and time Camera control ei Sync with computer time Modem E Application PC date 2001 10 18 vyyy mm dd Demo PC time 52 37 hh mm ss i Homepage layout e View log file mira E ew parameters Date 2001 10 18 yyyy mm dd i Factory default Time 20 52 20 hh mm ss Automatic NTP server sp to invoke default server Time zone ents 00 3 To
34. OM1 coml5 lt text string shorter than 80 characters gt custom command 5 of COM1 Modem configuration URL URL cgi bin serial2 cgi NAME VALUE DESCRIPTION dialout yes Allow the IT210 Network Camera dialing out on event lt other than yes gt no dial out allowed method Tone ATDT make modem dial in tone Pulse ATDP make modem dial in pulse mdmbaud lt integer gt refer to modem s specifications reatt lt integer gt redial attempts discon lt integer gt minutes delay before disconnection init lt text string shorter than 40 characters gt command to initialize modem phonel lt text string shorter than 40 characters gt phone number of primary ISP user lt text string shorter than 40 characters gt user name for primary ISP pass lt text string shorter than 40 characters gt password for primary ISP phone2 lt text string shorter than 40 characters gt phone number of secondary ISP user2 lt text string shorter than 40 characters gt user name for secondary ISP 89 Intellisystem Technologies http www intellisystem it ye Intellisystem IT210 User s Manual pass2 lt text string shorter than 40 characters gt password for secondary ISP Application configuration URL URL cgi bin app cgi NAME VALUE DESCRIPTION showalert lt notreguired gt show a
35. POST is successful status LED indicators will both shut off for a while and then light depending on the chosen network interface If Ethernet is available LED2 will flash like a heartbeat after network installation is done Otherwise if modem is available LED2 will flash alike to indicate listening for dial in connection while LED3 is lit If the included null modem cable is connected both LEDs will stay on and then LED2 will start flashing after the connection from the PC is opened for configuration and LED3 stays lit LED pattern after POST Possible failed component Failed function LED2 and LED2 blink at same U32 SAA7113 Video decoder time LED2 ON and LED3 OFF U1 TM1300 PCI bridge of TM1300 LED2 OFF and LED3 ON U6 RTL8139C Ethernet controller LED2 ON and LED3 ON U6 RTL8139C U7 U8 Ethernet interface LED2 blink and LED3 ON U22 M5823 Real time clock LED2 ON and LED3 blink U19 16C1550CJ P2 COM1 interface A Ethernet interface failure includes not only components on board but also Ethernet cable and the devices of the opposite end 92 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual B Freguently asked guestions Q What if I forget my password A Every access to the IT210 Network Camera needs authentication If you are not a permitted user you may view the images or control the camera as long as the demo account is opened Th
36. To look deep into the core debugging information administrators may type the debug command This will cause the IT210 Network Camera to start dumping the detailed debugging information while the system is running This is useful to examine if any error has occurred when the system operates abnormally The stored information will be cleared automatically after the dump The IT210 Network Camera will continue to dump new messages unless the connection is broken If Telnet is not connected any messages will be stored until administrators re login Monitor changed status of digital inputs Typing dinote will make the IT210 Network Camera send the current status of all digital inputs After that the IT210 Network Camera will continuously monitor DI status and send messages only when the state has changed For example after typing dinote the terminal will display DI1 L and after DI2 changes to H terminal will display DI1 H Stop information dumping Typing stop will cease dumping debug information and the digital input status TI Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Query status of digital inputs Typing diguery will display the status of all digital inputs once Set digital outputs To set digital output to connect NO with COMMON type DO1 L To set digital output to connect NC with COMMON type DO1 H Erase snapshots stored in Flash memory Typing
37. When the condition is matched the system will keep the intermittent captured images in memory as pre alarm snapshots and store the current images to the snapshots of the moment of trigged Subseguently the images captured at the next interval will be stored as post alarm snapshots The snapshots related to occurring event will be overwritten when another event occurs That means the IT210 Network Camera will keep these snapshots until another event occurs Regarding to I O event mode it is recommended that programming digital inputs with W or instead of H or L to prevent from freguent triggers 72 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Web Viewing system log Click the button on the configuration page to view the system log file The content of the file reveals useful information about configuration and connection after the system boots up Viewing system parameters Click the button on the configuration page to guickly view the whole system parameter set The content is the same as CONFIGINI Restore factory default settings Click the button on the configuration page to restore the factory default settings This means any changes made before will be lost and the system will be reset to the initial status as shipping out of the factory After confirmation the system will restart and reguire the installer program to setup the network Clear data pa
38. ace will be PPP with modem If either of the above is not the case the IT210 Network Camera will try the interface of PPP with null modem Network Interface Condition LED2 Heartbeat LED3 Status Ethernet before installed OFF OFF after installed flash OFF during camera control flash Flash PPP with modem after POST flash ON PPP with null modem before connected ON ON after connected flash ON 9 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Restore button HEDODDGS 654321 There is a button hidden in the box for restoring the system factory default settings When the system fails to install or operates abnormally use the included assistant stick in the package and follow the following procedures to reset the system back to its original status Poke the assistant stick into the hole to press down on the restore button Restart the system by unplugging and re plugging the power jack While keeping the button pressed the system will perform POST twice rather than the usual once which can be observed from the flashing LEDs After the system flashes the LEDs for the second time withdraw the stick to release the button The system will have restored factory default settings at that moment Power adapter Connect the power jack of the included power adapter Connecting the power adapter should be the last operation while physically
39. al 3 http 192 168 0 201 Microsoft internet Explorer tx 2 A R E x fa p rapin 92 168 0 201 Leaving Display string blank will hide the command button in homepage Display string Command 1 Command 2 Command 3 Command 4 Command 5 Factory default To enter more commands or commands other than pan and tilt a flexible URL is provided for customized interface See the Clear data path for proprietary commands section in Advanced functions for details 54 Intellisystem Technologies http www intellisystem it ye Intellisystem ECHNOLOGIES IT210 User s Manual Modem and dial up settings ZJ http 11200 1 1 11 Microsoft Internet Explorer F Dialout allowed Users Dial Method Tone ATOT XJ Network Baud Rate bps 1152008 ave Redial attempts s S Modem Disconnect after 1 minutes Application Initial modem command Homepage layout SP phone number 1 View log file Login usemame 1 View parameters rd 1 0 3 i Factory default Ta cea ISP phone number 2 Login usemame 2 Login password 2 In PPP interface a modem option will work instead of camera control Configurations include modem initialization and outside dial up server If the users will setup with external sensors and alarms for property security dial out is needed to send some snapshot attached e mails when the preset conditions are triggered In such applications
40. amera Homepage layout configuration URL URL cgi bin layout cgi NAME VALUE DESCRIPTION cuslogo blank hide logo def use default logo url use image from URL logourl lt text string shorter than 80 characters gt URL of image for logo linkurl lt text string shorter than 80 characters gt URL to link when clicking on logo cusback blank hide background image def use default background url use image from URL backurl lt text string shorter than 80 characters gt URL of image for background fcolor lt 0 15 gt color index for font bcolor lt 0 15 gt color index for background dismode image display homepage in image mode text display homepage in text mode 91 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Appendix A POST procedure After the power has been turned on the IT210 Network Camera will perform a self diagnostic to locate any possible hardware defects If the power indicator is dim at the beginning the power fails to proceed further While the POST is proceeding the status LED indicators will keep blinking interchanged until finished or any fatal error happens If either status LED indicator is dim at the beginning the LED may be broken Any possible fatal error has a special pattern shown in the following table LED2 is the one below the network indicator and LED3 is the lowest one If the
41. an 15 characters gt change root password username lt text string shorter than 15 characters gt add new user userpass lt text string shorter than 15 characters gt new user s password Deluser lt text string shorter than 15 characters gt existing user name Network configuration URL URL cgi bin network cgi NAME VALUE DESCRIPTION reset yes enable installation at next boot lt other than yes gt disable installation at next boot ip lt IP address gt The IT210 Network Camera s IP address subnet lt IP address gt subnet mask router lt IP address gt default gateway domain lt text string shorter than 40 domain name of the IT210 Network characters gt Camera dns 1 lt IP address gt primary DNS server dns2 lt IP address gt secondary DNS server smtp1 lt domain name or IP address gt primary SMTP server mailtol lt text string shorter than 80 mail recipient address characters gt smtp2 lt domain name or IP address gt secondary SMTP server mailto2 lt text string shorter than 80 mail recipient address characters gt return lt text string shorter than 80Ojreturn address characters gt http lt number less than 65535 gt HTTP port 85 Intellisystem Technologies http www intellisystem it sve Intellisystem IT210 User s Manual ftpl lt domain name or IP address gt primary FTP server ftpuserl lt text string shorter than characters gt
42. apshots When the IT210 Network Camera starts it will send out a system log to notify the administrator Even in modem application the IT210 Network Camera will send out a connection log whenever it dials out to an ISP or dialup server outside If the administrator has setup some applications in either event mode or seguential mode the IT210 Network Camera will send out snapshots once conditions are met There are two methods to send files including e mail and FTP To ensure the IT210 Network Camera sends out files correctly administrators should set valid SMTP mail server and Recipient email address as well as 47 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manual Primary FTP Server Primary FTP user name and Primary FTP password Primary FTP remote folder is the relative sub folder in the remote FTP server In both methods a Secondary server can be provided for backup connection However the primary server information should be entered first If the primary server is not set the related FTP or email will be deactivated Note that it may take time to connect to the secondary server after the first one fails and it may affect some applications when conditions happen too often After everything is set click on Esa A warning message will pop up Click on lt to confirm The IT210 Network Camera will automatically restart If Reset network at next boo
43. aten ipie estire Ene tbsdsiaywnstieesaeevaeveassessiebeventebetedt 41 Pan Tilt positioning device control serepin ne rrer e E en n n n a E E E naa aa na a Ka Kaanaan 42 System configuration vmatonasea ovan saanen aka Sana kaTAO an T nn Saa paa usa O onkaan vaan Nanovunsuuanas 3 Systemi Paraimoters ionumomamana sms kes sateen aayeetas saraa aseita sapen aak sa sai svadayet 44 User group administration vsaasss samassa Ka ITA asen E a ea aa Na naa EEE EE 45 NGtwWOrk SEUSS s ssisssisssscretssessceveesstsieuscstsanconasen cba antebsivesSiee ceded eves TUN TM KO seus koko alanokan saraa leuan 46 VIGEOPALAMECLELS s s55 sss svcsecscssssaccuedecassaedeusnsonesneeseds SEENE E NS 50 Camera positioning device configuration cuoouosuussssn nnen a na na na a n a na anna naan anaean 52 Modem and dial up settihes i assus sae a aitaa Tan aa E LKT a TUEN naamaa aN AHKKUT KAKKO vad aN AKA AKUN TUNNETUN 55 ADPICATON o s ss tapaan A a R E MAK KAUKIN SN eta 57 Demonstration account Settings v suossusssss sienen kaen n n na a Ta a a Ka Kaa a Ta nananana 61 Homepage l yout setting Sissin i n AE EE SANAN S ANETE EEE NS 62 One shot fast configuration Via FTP sssseesesssssessessesiseseseessrstsrsreestestneneesenenernreeesrnreeeesrenene 63 Advanced functions soessssssosssseseeoosoossosseseesosoososssossssoosososssossesoseoessssssssse TZ JALATTI SETTI Skata tav akat E T 72 Viewing system log cnennana ena e A EN SY 73
44. ayout Bandwidth limit Not timed EI 8 View log file View parameters hew 5 Factory default bert fo SMTP SMTP mail server Reapient email address Secondary SMTP mail TE server Secondary email address Return email address isuaiserver FTP Local FTP server port EI Primary FTP server ka Primary FTP user name 5 1 Primary FTP password e a Primary FTP remote folder Any change made to this page will make the system restart to validate Make sure every field is correctly typed before clicking on Save To eliminate incautious mistakes during installation the IT210 Network Camera will stay in installation mode whenever it starts unless Reset network at next boot is disabled This option can also be disabled using the Installer program Once the option is disabled the IT210 Network Camera will skip installation at the next boot and the Installer program will not find the installed 46 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual units That implies that the IT210 Network Camera cannot be accessed if no one remembers the IP address except by restoring factory default settings However with this option disabled the IT210 Network Camera can automatically operate normally after restarting in case of losing power This option is ignored in the PPP connection Administrators may modify the network settings to fit into
45. but at least one should be checking condition Digital input number 1 4 Digital input state H high L low low to high high to low operator OR AND 33 99 33 99 hour minute second set a time alarm repeats everyday hour set to 24 will check minute second every hour minute set to 60 will check second every minute M motion detection event Note that Upload snapshot while motion detected should be set in advance Digital output number 1 2 Digital output state H NC L NO lt example gt 17 30 00 M 1H will set NC of SW1 to short with COMMON after 17 30 or any motion is detected 1H 2 8 30 00 1L will set NO of SW1 to short with COMMON after 8 30 or DII high companied with DI2 transient from high to low Note that Upload snapshot while I O script matched should be checked in advance to enable function 60 Intellisystem Technologies http www intellisystem it sy Intellisystem ECHNOLOGIES IT210 User s Manual Demonstration account settings 5 http 192 168 0 201 Microsoft Internet Explorer gt 1 AW a fa I K gg ht 92168 0 2017 o F Enable demo account 8 Network Allow camera control while demo i Factory default To setup the IT210 Network Camera for demonstration to the public administrators need to choose service s to be opened After checking Enable demo account
46. change the system name type in the text box after Host name This name will be displayed at the top of the main page In the case that only the host name is changed without adjusting date and time of the IT210 Network Camera click on Keep current date and time There are three ways to adjust system date and time The easiest is to make the IT210 Network Camera Sync with computer time The second Manual is to set the date and time manually Notice the format in the related field while typing The third Automatic is to make the IT210 Network Camera automatically synchronize with timeservers over the Internet whenever the IT210 44 Intellisystem Technologies http www intellisystem it ye Intellisystem ECHNOLOGIES IT210 User s Manual Network Camera starts up It may fail if the assigned NTP server cannot be reached or it is within a local network Leaving the NTP server blank will let the IT210 Network Camera connect to default timeservers or type in assigned NTP server Domain name or IP address format is acceptable as long as DNS server is available Do not forget to set the Time zone offset for local settings It only affects the hour in NTP method Click on EE to validate changes User group administration TY http 1192 168 0 201 Microsoft Internet Explorer 2 2 09 1 g N Home Root password System Root password Users Network Confirm password kaiman Savo
47. d L means NO connected with COMMON For example http 192 168 0 201 setup setdo cgi dol h will command the IT210 Network Camera with IP address of 192 168 0 201 to set digital output to connect NC with COMMON Clear data mode serial port driver This URL applies to the attached serial port device including supported PTZ cameras or non supported custom cameras Note the serial port settings of custom cameras must be correctly defined in advance Send command to device attached to COM cgi bin senddata cgi data 123456 ABCDEF amp flush yes amp wait 1000 amp read 6 This hyperlink will inform the IT210 Network Camera to send out binary format commands to the 81 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual COM with 0x12 0x34 0x56 followed by OxAB OxCD OxEF Each comma separates the commands by 200 milliseconds flush yes means the receive data buffer of COM port must be cleared before read Then read 6 bytes after waiting for 1000 milliseconds The read data can be up to 128 bytes and will return as ASCII coded hexadecimal value e g 0x41 0x42 0x43 read from COM port will show in returned homepage as 414243 instead of ABC Restore factory default settings cgi bin restore cgi The IT210 Network Camera will automatically restart after restoring factory default configurations Restart system cgi bin reset cgi Restart the IT210 Network Came
48. d by an authentication message window A root password identical to the IT210 Network Camera s serial number is needed for the initial access to a newly installed IT210 Network Camera The administrator must change the root password immediately after the initial installation to ensure security The new root password should be well memorized since there is no way to retrieve or recover it After changing the password the browser will display an authentication window again to ask for the new password The other important part is network settings The software configuration above makes the IT210 Network Camera easily accessed through local networks However administrators should review the network settings on the configuration page according to the existing service The safe and easy way is to compare the network settings with another PC or workstation in the same network The software installation in the previous section only set the host IP address and default subnet mask as 255 255 255 0 Administrators should change the subnet mask if it differs from the one provided by the server Administrators should also fill in the default gateway primary and secondary domain name servers if necessary By default the IT210 Network Camera will need administrator s installation every time it reboots If 20 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual the network settings are sure to work all
49. e 9 Users Text on image J Video Default size Standard H Camera control 3 Modem Default quality Good J Application je Demo Homepage layout 5 View log file 5 View parameters mese Save Factory default Vertical flip Options on this page will affect the main page seen by users Time stamp and Text on image will be enclosed in image for reference The timestamp is captured from date and time of the IT210 Network Camera that is maintained by a built in real time clock Default size and Default quality options here will be the default size and quality when users first connect to the IT210 Network Camera Once the IT210 Network Camera needs to be installed upside down check Vertical flip for correct display 50 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manual To adjust image settings for best visual quality press __Image Setting and a motion picture window will pop up for your reference There are four fields including Brightness Contrast Hue and Saturation for video compensation Each field has eleven levels ranged from 5 to 5 The user may press _Preview to fine tune the image When the image is O K press 558 to memorize the image settings or restore to recall the original settings If parameters are changed without saving they will be used until the next system startup 51 In
50. e demo account user may use username as demo without any password to access limited features If you are one of the managed users you have to ask the administrators for the password If you are the administrator there is no way to recover the root password The only way to regain access to the IT210 Network Camera is to utilize the clear button on the front panel to restore the factory settings and reinstall it Q Why can I not watch video from the IT210 Network Camera after it is authenticated A There are many possible scenarios regarding this problem 1 If you have just installed the IT210 Network Camera and are unable to watch the video check if the video input is enabled and the video modulation in Configuration page 2 If the IT210 Network Camera is well installed and you are accessing the IT210 Network Camera for the first time using Internet Explorer adjust the security level of Internet Explorer to allow installation of the plug in 3 If the problem still exists after adjusting the current users may be over the system allows 4 In case that you use demo account the video may be protected from the public by the administrator Q What is the plug in for A The plug in provided by the IT210 Network Camera is used to display motion pictures on Internet Explorer If your system does not allow installation of any plug in software the security level of web browser may need to be lowered It is recommended that you consult you
51. ellisystem IT210 User s Manual The commands in Control settings should be edited in ASCII format The IT210 Network Camera will interpret the ASCII format command to binary string For instance 012000ABCD will be sent out of the COM port as five hexadecimal bytes of 01 20 00 AB and CD If the command string is composed of two or more commands a comma should be inserted to separate each command Each comma represents 200 milliseconds For instance a command to pan left may be 01000305 and a command to stop panning may be 01000300 The user may edit the applicable command as 01000305 01000300 in the Move Left field This means the camera will pan left for 200 milliseconds The maximal length of a command string is 60 which is equivalent to 30 hexadecimal bytes When everything is set click on 348 to save the commands and click on 982 to close the command setting window The IT210Network Camera provides five more custom commands other than general pan tilt functions Administrators can click on Custom Command and refer to the instruction manual of the attached device to setup frequently used functions The Command should be entered in ASCII format alike the pan tilt commands Display string is for those texts on command buttons and should be less than 8 characters 53 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manu
52. ensdancnssssvedeoededbncosdstebessiusssstotadesovassanensasonssbtedseedsne 81 Clear data mode serial port driver oo cic inka en n nen a a na Ka Kaa a Ta Ka Kaanaan 81 Restore factory default Stung rsrsrsr iriiri ia E E ER E 82 RESTaTTISY SUCIN AEREE E A RAAE ET NAR R TE T 82 Page UR Danean a RA R R E R E E AREE 83 System resource URL ccscssesissssiessossenestoconeptnscessasenssestneacsazescetscasspaieniosstansinapepepasnsdepabspaneasonatesvenes 84 General format of command URL sssessssssesseseesesssessestrsrsrsrssrsrsrsrerensistnesenstesisrnrneesrsrereseressene 84 System configuration URL wissrcsessssssseosscssssacesssssenssncsvsssvsdessacdstesssvesedesssovevsseveentecdeaseustesseleserenecsys 84 Users configuration URL vussju ssa cduacesecsceetisdebedessiasapioveioassssbicvetedessdebevveesisessontestsossesspenssesessvteds 85 Network configuration UR Lasisi rererere m raakaa vaasa aa naa ANETE EEEE KA KALA TT avas EEEE NEN 85 3 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Video configuration URL icc cee cscsdccscscacccssescacusecscosectensecedestcudevsnesensacasvavcosscusestebsenseessuansstusececees 86 Image quality configuration URL cece ce eececeeeeeceeceeeeecseeeeseeeseeseeseeseeesesaesaetaeseaeeagea 88 Camera control configuration URL cuuouussssssssses sitten k nana a a na a Ka Taa a na Ka naan annaean 88 Camera custom command configuration URL oo cece ekee ka a
53. ent mode F Show alert in image Home System Users le Network Delay 3 seconds before detecting next event k Video Take snapshot at E jtenth seconds after event e Camera control D Upload snapshot while motion detected B Modem anaiation PSS i Demo D Upload snapshot while 1 0 script matched i Homepage layout 5 View log file Extended 1 0 scripts View parameters if Factory default SS 3 J D Sequential mode Snapshot every kent seconds snapshot begin 50 00 00 hh mm ss snapshot end 00 00 00 nh mm ss Send snapshot by email Send snapshot by FTP FZ FTP file name with date and time suffix Administrators can use combinations of options on the application page to perform many useful security applications The sending method either e mail or FTP is selected at the bottom of the page Both e mail and FTP use the network settings on the network page If any mode is selected but server address of selected method is not properly setup the snapshots will only save in memory for access Administrators may check snapshots by clicking View Snapshot and managed users can use general FTP program to download snapshots kept in memory If another event occurs new snapshots will replace the old ones Administrators may configure upload method to send out automatically There are two application methods to upload snapshots Seguential mode will send out snapshots continuously over a co
54. er and click on N 8 The phone number used here is not important Make New Connection 28 Intellisystem Technologies http www intellisystem it TECHNOLOGIES Se Intellisystem IT210 User s Manual After clicking on Ca this new connection will display in the Dial up Networking folder and will be used for null modem connections Make New Connection My Connection Phone or Hosti 14 1234567 Device name Standard 33600 bps Modem To establish a dial up connection to this network now click Connest In the first General page clear Use area code and Dialing Properties option and click on 29 Intellisystem Technologies http www intellisystem it TECHNOLOGIES se Intellisystem IT210 User s Manual My Connection On the second page only check Enable software compression and TCP IP while leaving others blank Keep other settings as default values and click on SET Now the connection is ready for null modem connection 30 Intellisystem Technologies http www intellisystem it TECHNOLOGIES Sve Intellisystem IT210 User s Manual My Connection General PPP Internet Windows NT Server Windows 98 E n m eu m ke m m Double click the newly setup connection A dialing information window will pop up Enter root as user name and the serial number labeled on the bottom side of the box as the password and click on SEN The user name and pass
55. era to the electric power outlet Since most automatic detections of hardware perform when the system starts the IT210 Network Camera should be turned on after all peripherals are turned on and ready A Connect the power jack of the power adapter to the IT210 Network Camera prior to plugging the utility end into a utility power outlet It will reduce accidental electric surge shock 23 Intellisystem Technologies http www intellisystem it tti IT210 User s Manual ye Intellisystem Software configuration For the first time users should connect the included null modem cable between the COM port of the IT210 Network Camera and any COM port of the PC for initial setup Install a new modem Open the control panel and double click the modems icon E2 Control Panel Accessibilty Add New Add Remove Date Time Display Options Hardware Programs 4 amp Game Keyboard Modems Controllers Installs a new modem and changes modem g properties Network ODBC Data Passwords Sources Microsoft Home Technical Support 7 Power Printers RealPlayer G2 Regional Management Settings 2 E Telephony Tweak UI Users 24 Intellisystem Technologies http www intellisystem it TECHNOLOGIES se Intellisystem IT210 User s Manual Check Don t detect my modem item and click on SBT to install a new modem Install New Modem From Standard Modem Type choose the Standard 33
56. etwork Camera s configuration at once upload the accurately formatted batch file to CONFIGINI It is recommended to keep the original format but changing values Refer to the section in configuration for details and optional values as well After successfully receiving and verifying the file the IT210 Network Camera will self update the configuration and restart automatically Refer to the previous section for further information 75 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Software revision upgrade Customers can frequently check the appropriate product folder on our web site to download the latest firmware Only administrators can upgrade the system firmware of IT210 Network Camera How upgrade firmware 1 Decompress the compressed file in a local folder A file named FLASH BIN should appear 2 Use the FTP program and change the working directory to the local folder where FLASH BIN exists 3 Connect to IT210 Network Camera with user name as root and password 4 Use the PUT command to upload FLASH BIN to IT210 Network Camera The file size is near 1 5 mega bytes It will take approximately 2 seconds in a local network 2 minutes by null modem connection or 6 minutes by modem but still subject to user s network 5 After upload is complete close the connection 6 If the received FLASH BIN is checked without error IT210 Network Camera will update the software
57. figuration via FTP To allow users to connect to the IT210 Network Camera through an easily memorized name the administrators must first configure the name server in his network Here is an example When the administrator wants to set up the IT210 Network Camera with a fixed IP address and let users connect to the IT210 Network Camera by typing a name instead of IP address the administrator may reserve the IP from DHCP service and assign it with name in the domain name service During the IT210 Network Camera installation assign the ready IP address After successful installation users may access the IT210 Network Camera by the given name 18 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Manual way with existing programs For those environments such as MAC Linux Unix or other operating systems whose installer is not yet available some common network tools including ARP and PING can be used to install the IT210 Network Camera Make sure ARP and PING programs exist in your operating system First type arp s assigned IP address Ethernet address to add an entity in the system s name table The Ethernet address is identical to the serial number of the IT210 Network Camera and should be typed in the appropriate format like uu vv ww xx yy zz or uu vv ww xx yy zz which depends on the operating system Once a name entity is added type ping assigned
58. gh pin 5 and pin 6 If the distance from the controlled device is too far to allow accurate function an external power source may be used to pull high the RS485 signal The IT210 Network Camera provides one digital input and one relay switch Pin 1 and pin 2 can be connected to external sensor and the state of voltage will be monitored according to the programmed scripts in configuration The relay switch can be used to turn on or off external devices Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Status LEDs LED1 Network Tx Rx 1 2 LED2 Heartbeat 3 LED3 Status 12VDC Each time the IT210 Network Camera starts it will perform a Power On Self Test abbreviated as POST hereafter to examine every hardware module As soon as the administrator plugs in the power adapter both LEDs under the network LED will flash one by one until the POST is done If any module fails both LEDs will indicate to the users the error according to the pattern listed in Appendix A If the result is good both LEDs will turn off for a while and then follows the pattern below Network interface depends on the peripherals including Ethernet UTP cable modem or null modem cable If the Ethernet cable between the IT210 Network Camera and Ethernet hub is good the IT210 Network Camera will choose the Ethernet network If Ethernet is unavailable but a operational modem is connected the network interf
59. guickly update configurations and maintenance Both FTP server and client support the passive mode to pass general firewalls Those files with GIF extension are used for homepage layout and can be read and overwritten Those files with JPG extension are snapshots captured on reguest or events They also can be downloaded by managed users Other files will be explained below Uploading snapshots periodically to an external FTP server In seguential mode the IT210 Network Camera will send out snapshots according to interval and period settings If snapshot files are intended for guick updates it is better to skip date and time suffix The file name will then be video jpg If the snapshots are used for occasional monitoring suffix with date and time can help administrators classify them easily Viewing and downloading the stored snapshots There are three video image files for three stages pre alarm the moment when triggered and post alarm The files captured when pre alarm are vpre jpg The files captured at the moment when trigged are vtrg jpg The files captured when post alarm are vpos jpg Download the desired camera snapshot to be opened in browser Downloading the update snapshots Users can also download video jpg to take current snapshots of video channels The zero file size means it is captured by reguest It is useful for certain application to retrieve update snapshot via FTP 74 Intellisystem Technologies http www
60. ies http www intellisystem it yo Intellisystem IT210 User s Manual Notes 99 Intellisystem Technologies http www intellisystem it
61. ight of image which will be text buttons in text mode It allows users to control the PT positioning device attached to the IT210 Network Camera with pan tilt direction Additional five buttons below the image can be used to control cameras in ways other than pan and tilt They should be pre configured by administrators with reference to the instruction manual of the PT positioning devices Pie Modica Waman Aro Sueb m Ores O A BOQ Dou Perdew Gum O Ae nama e aomen Googe Odomcarelweb Ocrenmm E Deen Neer pugi Cerca dies E here 1172 10 10 1 24 pu IT210 Network Camera Quality Medium Standard Good Detaded Excellent Cngstal Output Size Half Half x 2 Standard Standard x 2 Dowble Open Close 1 wD Pan speed 3 Tik speed 0 2 Go to Select One 42 Intellisystem Technologies http www intellisystem it sy Intellisystem ECHNOLOGIES IT210 User s Manual System configuration There are two methods provided for configuration Web interface is quite easy and clear to use and FTP with script file is rapid for mass installation System configuration can be accessed only by administrators Administrators may type the URL below the figure to directly enter the configuration page If administrators also want to set certain options through the URL read the section on advanced usage for reference J http 11192 168 0 2011 Microsoft Internet Explorer
62. information and display the serial number and given IP address for each IT210 Network Camera as following figure If no DHCP service is available a previous IP address will be displayed instead In that case it may be 0 0 0 0 for a brand new unit When multiple units are mounted there may be several entries shown in the window Administrators may click on each entry with Assigned field labeled No to install sequentially 00 02 41 00 01 34 192 168 0 168 No 14 Intellisystem Technologies http www intellisystem it TECHNOLOGIES se Intellisystem IT210 User s Manual The IP address shown in Current IP Address field is for the administrator s reference If the administrator wants to use another IP address modify the IP text field below the list window IP Installer 192 168 0 168 No If the administrator wants to fix the IP address of the unit check the option Use this IP whenever system boots to skip future installation procedures Otherwise the unit will need installation whenever it restarts IP Installer 192 168 0 168 No 15 Intellisystem Technologies http www intellisystem it TECHNOLOGIES se Intellisystem IT210 User s Manual When IP and options are O K click on Memme A message window will pop open to inform if the IP address is valid IP Installer If the IP is not taken by another network device in the network the Installer program will continue with the set
63. is in image mode Administrators may use the following links to show the images saved in the IT210 Network Camera on another page To change the images referenced by the URL refer to the homepage layout section in configuration Resource name Referenced URL system logo image Nogo gif background image back gif button image for configuration btn_conf gif icon image for link indicator btn_text gif General format of command URL Every configuration can be set through URL with POST method by administrators only lt general format gt URL name value amp name value lt method gt POST lt authorized user gt root System configuration URL URL cgi bin system cgi NAME VALUE DESCRIPTION host lt text string shorter than 15isystem name characters gt method keep keep date and time unchanged auto use NTP server to synchronize manu directly adjust date and time date lt yy mm dd gt year month and date separated by slash time lt hh mm ss gt hour minute and second separated by colon lt domain name or IP address gt NTP server 84 Intellisystem Technologies http www intellisystem it ye Intellisystem IT210 User s Manual zone GMT lt n gt 00 time zone n ranged from 0 to 12 Users configuration URL URL cgi bin users cgi NAME VALUE DESCRIPTION rootpass lt text string shorter th
64. lert in image emode lt not required gt event mode application with either below mdmode lt not reguired gt enable motion detection emode should set iomode lt not required gt enable I O detection emode should set smode lt not required gt sequential mode application smethod mail upload snapshots by email ftp upload snapshots by FTP suffix lt not reguired gt FTP file with date and time suffix delay lt integer gt seconds delay to detect next event inter lt integer gt tenth seconds delay to capture post event sinter lt integer gt tenth seconds interval for seguential mode sbegin lt hh mm ss gt time to start seguential mode send lt hh mm ss gt time to stop seguential mode script 1 lt text string shorter than 40 characters gt I O script 1 script2 lt text string shorter than 40 characters gt I O script 2 script3 lt text string shorter than 40 characters gt I O script 3 script4 lt text string shorter than 40 characters gt I O script 4 Motion detection configuration URL URL cgi bin app cgi NAME VALUE DESCRIPTION per lt integer gt object size percentage sen lt integer gt sensitivity percentage 90 Intellisystem Technologies http www intellisystem it Se Intellisystem Demo configuration URL IT210 User s Manual URL cgi bin demo cgi NAME VALUE DESCRIPTION open lt not required gt enable demo account ptz lt not required gt allow demo user to control PTZ c
65. lisystem lt seconds delay before next event gt 3 lt script gt 0 sections 1 sections 2 sections 3 sections DEMO String String String String lt demo enabled gt NO lt ptz enabled gt NO or YES or YES shorter shorter shorter shorter 71 than than than than IT210 User s Manual 40 characters 40 characters 40 characters 40 characters Format Format Format Format refers refers refers refers to to to to Web Web Web Web Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Advanced functions Alarm settings The IT210 Network Camera provides flexible interfaces to cover most surveillance applications By easy script programming user can utilize up to four sensors with any signal pattern to monitor the environment Users may also use internal motion detection feature to combine with attached sensors to achieve best surveillance Once inputs or image variation meet the condition at real time checking the IT210 Network Camera will not only capture the images continuously but also e mail or FTP to the preset e mail address or FTP folder and or drive relays according to user defined patterns Generally the relays can be used to control alarms lights or door locks The condition script and motion detection are described in detail in the previous section
66. lj i f N j f ja W k f j e i f f A a X i lt a j p A KJ 7 7 j Fa l f ly lt N TY ak N v y S Fo y K Y N N ja JSN a f s b K v4 S j m j JA Sy i KAN Fay v f _ nA J j f f f i J A f f 4 v j v L N http Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Table of Contents Table of Contents sssessssoesssesssssoosssesossossscesssssosssessssssssssesssssssssesssse ll Before Yo U Se or visas sea esssacaasediccctaecnsetieastastnddedcastaicnciaucnesacsiscaccnscaczaneies N Package Contents e sssossosseccssssosocccessssosoeeecssssssooecessssosocosecesssssssessesssss Physical Description sesessssoccesssocessooosessooocseoosesssooesessoeesesoosesssossessosoe I Rear Pam iccsessccscccscsstscsscecesssvscsscsccsscdseseteacscsecssaveccscseasssoebecdesssepedecsonssevceseassesscces 7 Bthermmet 1 0 100 socketem a E N 7 Power adapters sumaa saaran R A E A S S 10 Auto Iris Lens Connector cccccccccccccesssssesseeeeeecescccceesaeeeeceeeeeceseesueeuaseeseeceseeceseeseeeeeeceeeeeeeeaas 10 How to Install e eeooossesoossoosssssssssssssessssosssssssssssssssessssosssssesssssssssessss L Ethernet Environment sesssssossssessssoosscessssososssssssssssscesssssosssssssssssss LO Hardware installation cccccccssssss
67. n 40 characters String shorter than 80 characters Integer less than 65535 Standard IP format or string shorter than 40 characters String shorter than 15 characters 67 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual String shorter than 15 characters lt ftp init path gt String shorter than 40 characters lt backup ftp server gt Standard IP format or string shorter than 40 characters lt backup ftp username gt String shorter than 15 characters lt backup ftp password gt String shorter than 15 characters lt backup ftp init path gt String shorter than 40 characters lt http server port gt 80 Integer less than 65535 lt bandwidth limit gt 0 0 128000 256000 512000 768000 1000000 1500000 2000000 VIDEO lt overlay timestamp gt NO or YES lt caption text gt lt colored video gt YES or NO lt video quality gt 4 2 3 4 6 8 representing ROUGH NORMAL GOOD DETAILED EXCELLENT lt brightness gt 0 among 5 and 5 lt contrast gt 0 among 5 and 5 lt hue gt 68 Intellisystem Technologies http www intellisystem it se Intellisystem 0 lt saturation gt 0 SERIAL lt auto detect camera gt NO lt data bits gt 8 lt stop bits gt 1 lt parity bits gt 0 lt baud rate gt 9600 lt enable camera control gt 0 lt uart mode gt RS232 lt other control commands gt 0 1 2 3 4
68. nfigured period This mode can be used to integrate with another web server to serve overloaded requests If the date and time suffix option is disabled the IT210 Network 57 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Camera can use FTP to upload and overwrite snapshot files periodically The remote folder of snapshot files for FTP can be configured on the network page The snapshot period is between Snapshot begin and Snapshot end and it will repeat everyday The snapshot interval is set among to 999 in Snapshot every tenth seconds and thus the minimal interval can be 0 1 second The other Event mode can be used to combine motion detection with devices attached to the digital input to drive the device attached to the digital output or send out snapshots for evidence It helps users to establish an all purpose security system Both or either one of motion detection and matched I O scripts will trigger the IT210 Network Camera to snapshot three stages of events and send them to server outside The IT210 Network Camera will continuously monitor the video channel every half second If any event occurs the IT210 Network Camera will keep the previous snapshot and current snapshot in memory and take another snapshot after certain delay set in Take snapshot at tenth seconds after event by the administrator Three stages of snapshots will be VPRE JPG VTRGJPG and VPOS JPG Since
69. oftware Upgrade System firmware upgradeable via FTP Security Administrator and user group protected 15 digits password protection Demo account with limitation by administrator Optional Software Record and play pictures on PC hard disk I O ports monitoring feature LED Indicator Heartbeat indicator Status indicators Network indicator Power 12V DC 1 2A external power supply Viewing System Reguirement Protocol Standard internet TCP IP suite Operating System Microsoft Windows Linux Unix and Mac OS Browser Internet Explorer 4 x or above Netscape Navigator 4 x or above Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Electromagnetic Compatibility EMC USA This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a partial installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct
70. ors also can give the system logo a Logo link to refer to another web site The Font color and Background color can be chosen from sixteen colors to achieve the best visual effect There are two homepage display modes The first is Image mode that uses images for links See Customizing images of homepage section in Advanced functions for how to replace images The other is Text mode that mostly uses text for links The camera control panel is also replaced 62 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual by text buttons below the image One shot fast configuration via FTP For quick setup of the IT210 Network Camera the administrator can utilize the default CONFIG INI that may be downloaded from the FTP daemon of the IT210 Network Camera To log into the FTP daemon enter root as the user name and the same password used when connecting to the Web server The serial number of the IT210 Network Camera is the password for the initial access Then administrators only need to modify necessary fields and then upload the file to the IT210 Network Camera with the file name CONFIGINI To reduce error in interpretation it is recommended that the downloaded template CONFIGINI be modified using the options following each item in the sample below The file will include seven categories SYSTEM NETWORK VIDEO SERIAL1 SERIAL2 DIDO and DEMO The catego
71. ower security levels or contact network supervisors However Mac users or Netscape Communicator users does not need to install it The web browser has already supported the motioned pictures internally 36 Intellisystem Technologies http www intellisystem it ECHNOLOGIES sy Intellisystem A http 172 16 10 81 74 Microsoft Internet Explorer File Modfics Visualizza Preferiti Strumenti O rasto Q x a A p gt cerca 7 Preterti raved e 8 N an IT210 User s Manual f X ap e indirizzo http 172 16 10 81 74 v Edva Collegamenti e A Intellisystem IT210 Network Camera Quality Medium Standard Good Detailed Excellent jae size x D npr Tae a aonne cal Ti Configuration The pan cower be deterred d to the stina tom ag Aathertcode apshre ret kard ps a mene 2 iemet Primary user s capability Main screen with camera view Basic functions are displayed in main entrance page of the IT210 Network Camera The first figure below is text mode that will shorten download time and the second one is graphic mode that has better visual effect Text mode is default if any image button is not available 37 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manual F ipii 72 16 10 81747 Microssti Internet Explsee Fle Modica eliza Prefer Strumenti Quem O AG Pom femia nme O Googk
72. r network supervisor in your office regarding the adjustment of the security level Q Why is the timestamp different from the system time of my PC or notebook A The timestamp is based on the system time of the IT210 Network Camera It is maintained by a real time clock inside and automatically synchronizes with the time server if the IT210 Network 93 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Camera is connected to the Internet and the function is enabled Differences of several hours may result from the time zone setting Q Why does the image not refresh regularly A In a modem environment it is because the bandwidth of PPP connection is far less than Ethernet If the difference of the timestamp is not stable adjust the UART FIFO lower in both receiving and transmitting from modem property in the control panel While in Ethernet it may be due to insufficient network bandwidth shared by other users Q How does the IT210 Network Camera detect the supported PTZ cameras automatically A When the system is powered up the IT210 Network Camera will monitor the CTS of camera control cable continuously As long as the CTS is detected the IT210 Network Camera will try to handshake with supported cameras until a supported camera is found There is no more camera detection once a PTZ camera is recognized Q How many users are allowed to watch the IT210 Network Camera a
73. ra without warning 82 Intellisystem Technologies http www intellisystem it Se Intellisystem Page URL IT210 User s Manual The configuration page has a frame layout including option list frame and an option page frame Referenced URL except for the configuration page directs to option page frame only Some pages like image guality setting and preset setting are opened in new windows for preview These URLs can be accessed only by administrators Homepage name Referenced URL configuration page setup config html system option setup system html users option setup users html network option setup network html video option setup video html image guality option setup image html camera control setup seriall html modem setup serial2 html custom command setting setup cuscom html application option setup app html motion detection setting setup motion html view snapshots setup snap html demo option setup demo html homepage layout option setup layout html system log setup logfile html system parameters setup parafile html set factory default setup factory html 83 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual System resource URL There are some images used on the homepage when the homepage layout
74. rite CODEBASE plugin mjpegcontrol cab version 1 0 0 3 gt document write lt PARAM NAME VSize VALUE 2 gt document write lt PARAM NAME V UrN VALUE V http 192 168 0 201 cgi bin video jpg document write cam 1 amp quality 3 amp size 2 gt document write lt OBJECT gt else document write lt img width 352 height 240 document write src http 192 168 0 201 cgi bin video jpg cam 1 amp guality 3 amp size 2V gt gt lt script gt lt body gt lt html gt EEEE EE FISK SK SK SK SK KE KK KK SK SK SK SIS SC SS E aie E aie ig E E ig E E aie K aik aik aik aie E FIC FIC KE FIC FS KE K akk K aie aik aik K K ai K K K K K K K K K K K K K K KK KKK KKK K KKK 80 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Get stored snapshots from Flash memory cgi bin snapshot jpg file lt filename gt filename snapshot stage snapshot before event pre snapshot upon event trg snapshot after event pos Move positioning device in PT direction lt direction gt up left right down home cgi bin control cgi cam lt input source gt amp move lt direction gt Query status of digital inputs setup getdi cgi The IT210 Network Camera will return status of the digital input in one line Drive digital outputs setup setdo cgi dol lt state gt where state is H L H means NC connected with COMMON an
75. ry name in brackets should be in upper case The item name in angle braces should be in lower case Some items related to disable enable should use the keywords YES NO The number zero entry in lt user name gt and lt user password gt is for administrators i e root Since the password when logging into FTP is not encrypted it is recommended to use Web instead of FTP to configure the system afterwards If some parameters other than the network or camera drivers are changed administrators can set lt reset system gt to NO to avoid resetting the system It will automatically return to YES during the next downloading of CONFIGINI A sample CONFIGINI is attached below The italic text following each line describes the format of the field and the bold italic characters are the possible values of each field IT210 Network Camera Initial Configuration File SYSTEM lt reset system gt YES Reset system after reading CONFIGINI or NO lt host name gt 63 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual IT210 Network Camera String no more than 38 characters lt serial number gt 0002D1000001 Read only string lt software version gt IT210 5168 0100 Read only string lt current date gt 2004 08 14 year month date Read only string lt current time gt 07 00 00 hour minute second Read only string lt time zone gt 0 From 12 to 12 lt user name gt
76. ssssssscccccccccccsccsccsccccscecccsccscscccscccccccsscscsecee LD Cable COnne Ct OM scccsssessseadcssesnaxacescadeessezaceaacenacasacaveeseaeveacaaaeesausanevensiaceecsanasaaaesaaeaeoinanesaadesesasetea 12 Manual way with existing PrograMs cece ien cece ceeeeeeeeeeeeeeeseeseeseeseeesneteseteeaeeeaae 19 First access to the IT210 Network Camera ccccccscosssssssssssssssscscccccscsesse 20 Modem Environment cccccccccccccscscccccccccssscccccsccsccccccsccccsccsccsccsesss 22 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual Hardware installation ccccccccsssssssssscccccccccccccccssssccccscscsccccccscccsssscscsccecssesesss Z2 Cable Connection ooooooousnnnn nona anna aan kaan aa aa aa ana a naakka aa aa naa a anna aa aan annan 23 Setup a NEW CONCOTON1ssisssn persa erare Ama a lah avaavan aa aan ASKERE ES saan kankaan assa 27 First access to the IT210 Network Camera cccsccccsssssccsssssscsssssssccsssssres JI AuhEntioatIohksssmstsme tatu SKTav rk T seas v en S rooster adess ose ast rs sasta Primary users Capabuutysisomsasvossussaaa mauvustetaavaase vessat sat Taaseonasa DV Main screen with camera View vuousss inen na eaa aa aa ea aa a a eaa KaU a a aa naa a naa aa eee 37 Vid orguality Selection lt s saikiassasasaamasas aan Kasa taa Kaanaan naa SEEE EnS EERE NDE T EEE EET asua nan 40 Wid EOiSIZE selem eeano heir
77. t is kept checked run the installer procedure again Otherwise the IT210 Network Camera will restart automatically 5 http 192 168 0 201 Microsoft internet Explorer D JAIA a glp J p het 182 168 0 201 co F Reset network at next boot 8 System General Users IP address 192 168 0 203 je Network 8 Video Subnet mask ss2552550 Camera control Default router 192 168 0 5 5 Modem kasan cS asnilcaeion Primary ONS server 192 168 0 1 Demo Secondary DNS server 168 95 1 1 amp Homepage layout Bandwidth limit Notimted M View log file 5 View parameters Factory default Microsoft Internet Explorer Local FTP server port E Primary FTP server Il 11 lt 4a Primary FTP user name VA Primary FTP password Primary FTP remote folder Administrators should notice that the IP address subnet mask default router and DNS servers will 48 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual be cleared when the network interface is switched to the other Refer to the related section of Ethernet or modem for software installation 49 Intellisystem Technologies http www intellisystem it ECHNOLOGIES Sve Intellisystem IT210 User s Manual Video parameters J http 192 168 0 201 Microsoft Internet Explorer Pe B A G a 4 zA hipin 92 168 0 201 o D Show timestamp in imag
78. t the same time A To achieve the best effect the IT210 Network Camera will allow twenty users to connect at the same time It is recommended to build another web server to host a large quantity of users by retrieving images from the IT210 Network Camera periodically Q How fast is the video rate of the IT210 Network Camera A The JPEG codec can process 30 frames per second internally However the total performance is subject to many coefficients as follows 1 network throughput and bandwidth share 2 number of users lt Formattati Elenchi puntati numerati 3 the complicated objects in view results in larger image file 4 the level of your PC or notebook which is responsible of displaying images In general the transfer rate in general local network environment can achieve over 200 kilobytes per second and approximately 10 to 20 pictures of normal environment per second Q How can I keep the IT210 Network Camera as private as possible A The IT210 Network Camera is designed for surveillance purpose and has many flexible 94 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual interfaces The user authentication and special confirmation in installation can keep the IT210 Network Camera from unauthorized access You may also change the HTTP port to non public number You can check system log to examine any abnormal activities and trace the origins Q How fast
79. t video guality and size cgi bin video jpg guality lt image guality gt amp size lt image size gt There are three parameters may be added for specific reguirement Absent parameter will be replaced by original value lt image guality gt 1 for medium 2 for standard 3 for good 4 for detailed and 5 for excellent lt image size gt 1 for half 2 for normal 3 for double 4 for halfx2 and 5 for normalx2 In additional to the URL some scripts should be added to download a plug in for motion pictures The following example simply displays title text and a real time video window in Internet Explorer or Netscape To have the original HTML file for reference users may right click on the browser window to view and save the source Those who are familiar with HTML can easily add more components or rewrite a more vivid and useful homepage KKK KK lt html gt lt head gt lt title gt IT210 Network Camera Sample Page lt title gt lt head gt lt body gt 79 Intellisystem Technologies http www intellisystem it se Intellisystem IT210 User s Manual lt h2 gt IT210 Network Camera Sample Page lt h2 gt lt script language JavaScript gt lt if navigator appName Microsoft Internet Explorer amp amp navigator platform MacPPC document write lt OBJECT ID MjpegControl WIDTH 352 HEIGHT 240 document write CLASSID CLSID EAA 105FE 7BBD 4196 8B96 D46743894195 document w
80. tellisystem Technologies http www intellisystem it ECHNOLOGIES ye Intellisystem IT210 User s Manual Camera positioning device configuration J http 11192 168 0 2011 Microsoft Internet Explorer x Enable camera control j m s ea Interface mode 5232 6 Video Port settings Camera contra Baud Rate bps 1152008 Data Bits sm 5 Demo Stop Bits ka 8 Homepage layout parity Bit None ey oa 190 Control Settings verona ewe Move Down _ Move Left Move Right p Home J custo Commend Since the IT210 Network Camera can be used in either PPP network or Ethernet network the single serial port can control either external serial port devices like camera positioning devices or a data modem While in PPP interface go to Modem page for modem configuration Options on this page will be ignored To control the external PT positioning device Enable camera control must be checked and the control panel or buttons will thus display on the main page The IT210 Network Camera supports RS232 and RS485 interface to control external serial port devices Refer to the hardware description to connect an RS485 device The Port Settings and Control Settings must be configured according to the instruction manual of the external serial port device The Baud rate bps of the serial port is up to 115200 bps 52 Intellisystem Technologies http www intellisystem it se Int
81. th for proprietary commands The IT210 Network Camera provides a highly customized control support to third party serial interface devices aside from PTZ cameras That means in addition to setting up a custom camera with PTZF commands users may utilize this mode and introduce a customized homepage to transmit arbitrary user defined commands from user side to the IT210 Network Camera The third party device connected to the serial port of the IT210 Network Camera will receive the same command sent by the originator The user only needs to attach the command in ASCII format after the special URL The IT210 Network Camera will parse the commands and transfer into binary code to send out See the clear data mode serial port driver in the URL commands of the IT210 Network Camera section for detailed description 73 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual FTP The IT210 Network Camera not only has web service for easy access but also builds in FTP service to make system integrators easy to use According to settings on the application page the IT210 Network Camera can seguentially send updated snapshots over a specific period to an external server with choices of overwriting and time suffix For security staffs the IT210 Network Camera can directly send snapshots to external server for evidence according to event settings Through the IT210 Network Camera s FTP daemon administrators can
82. the POST power on self test is complete and the result is successful the IT210 Network Camera is ready for software configuration as described in this manual At this stage network speed and video modulation type are automatically detected If the detection of video modulation fails administrators may change the setting on the configuration page Refer to the configuration section for further information A Connect the power jack of the power adapter to the IT210 Network Camera prior to plugging the utility end into the utility power socket It will reduce accidental electric surge shock 13 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manual Software configuration Easy way with installer program In order to configure IT210 Network Camera remotely administrators should keep the serial numbers of the new IT210 Network Camera for identification and initial passwords After successfully mounting IT210 Network Camera in the proper position run the Installer program on the appropriate PC to locate the newly installed IT210 Network Camera IT210 Network Camera also support manual setup procedures to non Windows based environments The manual procedure is described next After the POST is done the IT210 Network Camera will try to configure itself by detecting the network environment If there is DHCP service over the network the Installer program will catch the given
83. the same event may exist for a while administrators can set delay time in Delay seconds before detecting next event to reduce multiple triggers by the same event To ensure correct snapshots of events the value cannot be shorter than the delay of Take snapshot at tenth seconds after event Note that Event mode should be checked in advance to enable event trigger application Furthermore Upload snapshot while motion detected and or Upload snapshot while I O script matched should be checked with to work If neither upload condition is checked Event mode will be cleared even if the administrator has checked it previously Similarly if Event mode is not checked any upload condition will be cleared no matter the administrator has checked them or not Only upload condition is checked as well as Event mode is checked will make the IT210 Network Camera check the condition in real time If motion detection is enabled or extended I O scripts are edited administrators can click on Show alert in image to display the event status in upper right corner of image It will be white character with red background M means motion is detected while 1 to 4 mean matched I O script number 1 to 4 If neither mode is checked Show alert in image combined with motion detection and or I O script still works for indication To integrate with external recorder software 58 Intellisystem Technologies http www intellisystem it EC
84. ts as a server the user name and password used in dialing are the same as what was stored in the user database managed for web access Any managed user can be authorized during PPP negotiation and access web pages However only administrators can access the configuration page There is more information needed for correct modem operation Refer to the modem setting section in configuration for further settings The IT210 Network Camera will wait for someone to dial in If the administrator has setup some conditions in the application the IT210 Network Camera will automatically dial out based on the administrator s configuration Refer to the application section in configuration for special security applications After everything is set and saved turn off the IT210 Network Camera and replace the null modem cable with modem for dial up network Since the null modem connection is used to configure the IT210 Network Camera in advance for modem connection administrators cannot connect again without restarting the system If dial out configuration is activated the IT210 Network Camera will dial out to send a system startup log to test and drop the call after the pre configured period 34 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Authentication The IT210 Network Camera is a well designed stand alone network camera With the built in web server authorized users may use any popular
85. ty check of COMI to even up lt text string shorter than 80 characters gt tilt up command string of COM1 down lt text string shorter than 80 characters gt tilt down command string of COM1 left lt text string shorter than 80 characters gt pan left command string of COM1 right lt text string shorter than 80 characters gt pan right command string of COM1 home lt text string shorter than 80 characters gt home command string of COM1 88 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual Camera custom command configuration URL URL cgi bin cuscom cgi NAME VALUE DESCRIPTION str11 lt text string shorter than 8 characters gt button name of custom command 1 of COM1 str12 lt text string shorter than 8 characters gt button name of custom command 2 of COM1 str13 lt text string shorter than 8 characters gt button name of custom command 3 of COM1 str14 lt text string shorter than 8 characters gt button name of custom command 4 of COM1 str15 lt text string shorter than 8 characters gt button name of custom command 5 of COM1 coml1 lt text string shorter than 80 characters gt custom command 1 of COM1 coml2 lt text string shorter than 80 characters gt custom command 2 of COM1 coml3 lt text string shorter than 80 characters gt custom command 3 of COM1 coml14 lt text string shorter than 80 characters gt custom command 4 of C
86. up Otherwise another message window will warn that the assigned IP conflicts In this case administrators should ask the network supervisor for a vacant IP address IP Installer 16 Intellisystem Technologies http www intellisystem it TECHNOLOGIES Se Intellisystem IT210 User s Manual After successful notification IP Installer administrators may keep the address information for user s request 192 168 0 168 After clicking on EZ the Assigned field will be labeled Yes Administrators may click directly on Linktosdeeotsevet to access the newly installed server in the default browser IP Installer 192 168 0 201 Yes 17 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sve Intellisystem IT210 User s Manual While checking Use this IP whenever system boots a dialog window may pop out to ask for Server FTP Port and Root Password because they are already changed to other than default settings If the settings are lost restore default settings and use installer to install again IP Installer Once installation is complete administrators should follow the actions in the First access to the IT210 Network Camera section for necessary checks and configurations Experienced administrators may use the customized config ini script file to perform a quick setup via FTP Detailed procedure can be found on the section One shot fast con
87. web browser such as Internet Explorer and Netscape Navigator to watch the video captured by the IT210 Network Camera The powerful video compression processes 30 frames per second and makes the scene in your browser real time display The high resolution CCD and high performance lens assure the best image guality Another benefit of web interface is that each function and each configuration has its specific URL that allows advanced users to easily integrate them into existing software programs The preparation of the primary users to utilize the IT210 Network Camera is guite simple since administrators have done the majority of the installation Most administrators find the installation is easy in general environments because most settings are automatically configured Open your familiar web browser and connect to the IT210 Network Camera just like a general web site and the video will present on demand Make sure the web address of the IT210 Network Camera s target is accurate If the image looks flickeringly the product model may have the wrong video modulation with your regional regulation Please consult with your local dealer After opening the Web browser and typing in the URL of the IT210 Network Camera a dialogue window will pop up to reguest a username and password For administrator s initial usage of the IT210 Network Camera enter the username as root and the password as the serial number in capital letters The serial number can be
88. word are identical to what is used in web access and may be changed by administrators after successful installation Notice that the letters in the serial number should be capital form For example type A instead of a After some negotiation prompts a connection status window will show the speed is 115200 bps Connect To 1234567 New Location E 31 Intellisystem Technologies http www intellisystem it Se Intellisystem IT210 User s Manual After connection is established successfully go to the next section First access to the IT210 Network Camera If an error message indicates a hardware error while connecting for the first time especially in a Windows 2000 environment try again to recovery the possible detection failure 32 Intellisystem Technologies http www intellisystem it TECHNOLOGIES sy Intellisystem IT210 User s Manual First access to the IT210 Network Camera Through direct connection by null modem cable administrators can open the default web browser and type in 200 1 1 1 as the address and press enter Note that 200 1 1 1 will be the default IP address in a dial in connection and 200 1 1 100 will be the given IP address for the user s PC by the IT210 Network Camera The user name and password are the same as what was entered during installation J Carat rd server Mecreest internet E apinrer i The page cannot be diepleyed ee oo er he See a ae

Before You Use - Intellisystem Technologies S.r.l.

Contents

Download Pdf Manuals

Related Search

Related Contents