Home
PCRW404K - Virgin Media
Contents
1. Setting the Philips CD Rewriter as the SLAVE As shown in the diagram at the right insert the jumper pin into the middle of the jumper switch CSEL Cable SELect If you choose the CSEL setting the MASTER SLAVE setting will be made automatically depending on your hardware configuration For details refer to the user manual of your computer Chapter 2 Installing your Philips CD Rewriter 9 oO cd rom BASIS UK_400nw 11 08 1999 10 45 pae 10 Installing your Philips CD Rewriter drive The following steps may differ slightly depending on the type of computer you are using For details on removing the cover from your computer and installing or removing internal devices refer to the user manual for your computer 1 Switch off your computer and unplug it from the mains power outlet If you fail to do this there is a danger of electric shock and or of causing short circuits which may damage the computer and or your Philips CD Rewriter drive 2 Remove the cover from your computer Be careful not to lose the screws that were removed 10 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 gae 11 3 Your hands or body may be holding a charge of static electricity Touch a metallic portion of the chassis or the power supply to discharge the build up 4 Remove the front cover of a vacant half height drive bay For details refer to the user manual of your compu
2. RGND L SL 5 GND 12 IM I TT a ee Eee gt z Jumper Switch Enhanced IDE compatible computers normally have two IDE interface connectors a primary one and a secondary one Each IDE interface connector of the host computer allows up to two IDE devices to be connected This means that a total of up to four IDE devices can be connected Normally a hard disk is connected to the primary connector and a CDROM drive is connected to the secondary connector Important Avoid connecting your Philips CD Rewriter or a CD ROM drive to the same primary connector as the hard disk drive In order to take full advantage of the systems performance we recommend that you connect your Philips CD Rewriter to the secondary connector by itself as the MASTER Make sure that any other drives that are connected to the same cable have their jumper settings set to SLAVE Verify each respective drives owners manual for instructions on jumper settings 8 Philips CD Rewriter Oo cd rom BASIS UK_400nw 11 08 1999 eat qgeaine 9 Setting your Philips CD Rewriter as the MASTER As shown in the diagram at the right insert the jumper pin into CSEL SLAVE MASTER the right edge of the jumper switch Note Lf only your Philips CD Rewriter will be connected to the IDE interface connector connect the Philips CD Rewriter to the end of the connector
3. IMPORTANT When connecting this product to accessories and or another pro duct use only high quality shielded cables Cable s supplied with this product MUST be used Follow all installation instructions Failure to follow instructions could void your FCC authorization to use this product in the USA NOTE This product has been tested and found to comply with the requirements listed in FCC Regulations Part 15 for Class B digital devices Compliance with these requirements provides a reasonable level of assurance that your use of this pro duct in a residential environment will not result in harmful interference with other electronic devices This equipment generates uses radio frequencies and if not installed and used according to the instructions found in the users manual may cause interference harmful to the operation of other electronic devices Compliance with FCC regulations does not guarantee that interference will not occur in all instal lations If this product is found to be the source of interference which can be deter mined by turning the product OFF and ON please try to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Utilize power outlets that are on different branch circuit breaker or fuse circuits or install AC line filter s In the case of radio or TV interference relocate reorient the antenna If the anten
4. Long nose pliers These are used to insert or remove the jumper pin when setting the MASTER SLAVE settings of your Philips CD Rewriter drive Long nose pliers 6 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 pne 7 Discs You may use conventional CD RW and CD R discs with your Philips CD Rewriter Philips recommends you use only Philips CD RW and CD R discs which are available at your retailer CD RW Discs 9120mm 74 minutes CD R Discs o120mm 74 minutes Read only Discs You can use discs with the liste logo which conform to the Compact Disc Read Only Memory standard If you wish to use the audio functions use discs with the liste logo which conform to the Compact Disc Digital Audio standard Chapter 1 System Configuration 7 Oo cd rom BASIS UK_400nw 11 08 1999 10 45 pane 8 Chapter 2 Installing your Philips CD Rewriter Drive MASTER SLAVE settings Before you install your new Philips CD Rewriter in your computer you must first make the MASTER SLAVE setting This setting is set by inserting a jumper pin in the jumper switch located on the rear panel of the Philips CD Rewriter drive Important When the unit is shipped from the factory this setting is in the MASTER position Note Use long nose pliers to remove or insert the jumper pin Rear Panel 0 0 0 0 0 0 0 Q oOo O 0O O 0O 0O O PEE 0o00 o0oo0oo0oo0o0 SLAVE IDE Pin CABLE SELECT AUDIO OUT CA DCINPUT
5. Your Philips CD Rewriter can both record and read seven different formats CD ROM CD ROM XA CD I CD DA CD Bridge multisession CD Extra and Video CD Your Philips CD Rewriter is also equipped with an analog audio output terminal headphones for CD DA ATAPI for High Volume High Speed Data Transfer Your Philips CD Rewriter features an ATAPI IDE interface for connecting computers and peripheral devices ATAPI provides high speed transmission of large quantities of data which is especially important when working with image data Recording Modes Track at Once In this mode data can be recorded to disc one track at a time Discs recorded in this mode cannot be played in CD players or CDROM drives other than a CD RW or a CD R drive until the session is closed Disc at Once In this mode data can be recorded to an entire disc in one pass It is not possible to write additional data later Session at Once In this mode data can be recorded to the disc one session at a time To use this mode your software must support Session at Once recording New sessions can be written later Packet Writing This is useful for data back up Smaller units of data can be added to tracks To use this mode your software must support Packet Writing Your Philips CD Rewriter supports both sequential and random packet writing 4 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 pne 5 READ ME FIRST Just as your primary applications
6. disc Manual Eject emergency use We will explain below how to eject the disc when the tray cannot be opened in the normal manner for example if the power is shut off inadvertently or the loading mechanism fails This technique should be used only as a last resort Frequent use may lead to malfunction You will need a rod like object of 1 mm or less in diameter to do this A straightened paper clip works well 1 Insert the pin like tool into the manual eject port and push gently The spring loaded mechanism ejects the disc 2 After manually ejecting a disc you must turn off the power supply to your Philips CD Rewriter then turn it back on before continuing Chapter 3 Operation 17 Oo cd rom BASIS UK_400nw 11 08 1999 10 45 pases 18 Troubleshooting If your Philips CD Rewriter is not performing as expected we suggest you look up the symp toms in the following table and take the appropriate corrective action Symptoms Corrective action The DISC LED is off yet your computer is Check the DC power cable connection powered up to the drive Your Philips CD Rewriter is not recognized by Check the IDE interface connection your computer Is the MASTER SLAVE setting correct If there is only one device connected to the IDE interface connector is it connected to the end of the connector The disc tray will not open Make sure that the power to the computer is turned on The d
7. This control adjusts the volume level of the headphone output Rotating the control wheel clockwise to the right will increase the volume level 4 WRITING LED This indicator is illuminated when writing overwriting the CD 5 DISCINLED This indicator flashes when data is accessed and is illuminated green when there is a disc in the drive Chapter 3 Operation 15 cd rom BASIS UK_400nw 11 08 1999 10 45 pae 16 6 Eject button This button is used to open or close the tray 7 Manual Eject port This is used to manually eject a disc that cannot be ejected in the normal way It is for emergency use only Loading a Disc 1 Press the eject button to open the tray 2 Carefully place the disc label side up on the disc tray 3 Press the disc tray softly or press the eject button again to close the disc tray 16 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 pae 17 Ejecting the Disc If your Philips CD Rewriter is powered up Press the eject button to eject the disc Note You cannot open the tray if the ATAPI command prohibits the eject operation while your Philips CD Rewriter is reading data Caution Be sure to remove the disc only after the tray is completely open Attempting to remove the disc before it is completely ejected may cause the drive to malfunction Press the eject button If your Philips CD Rewriter is not powered up Pressing the eject button will not eject the
8. Write2CD Audio Write2CD Backup and Write2CD Data PacketCD has been designed to offer you the most advanced technology in CD recording with UDF packet writing you will be able to use your CDs in virtually the same way you use your other storage devices such as floppy disks hard drives etc To facilitate using UDF packet writing PacketCD will automate some of the tasks When you insert a blank CD R or CD RW disk the Write2CD wizard will pop up showing your CD Recording options The first option is to format a disk using PacketCD After selecting this option PacketCD will guide you through the PacketCD application Please note that to be able to format a disk the application needs to sense a blank disk This may require a few moments When you insert a previously recorded disk using PacketCD or a different UDF packet writing solution the Write2CD wizard will not start since this disk is already formatted and you can address it directly from your Windows explorer or all popular Windows applica tions If this is the case Write2CD needs to start the reader which may require a few moments Please note the following recommendations y when you insert a blank CD wait for the wizard to pop up which will guide you further in case the wizard doesn t pop up simply start your Windows explorer By clicking on the right mouse button you will be able to format your blank CD and proceed y when you insert a p
9. cd rom BASIS UK_400nw 11 08 1999 10 45 pene 2 LASER SAFETY This CD RW drive employs a laser Do not remove the cover or attempt to service this device when connected due to the possibility of eye damage CLASS 1 LASER PRODUCT CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS LASER RADIATION EXPOSURE CAUTION LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM FOR EUROPE The CD RW drive is in conformity with the EMC directive and low voltage directive cd rom BASIS UK_400nw 11 08 1999 10 45 pene 1 COMPLIANCE INFORMATION STATEMENT DECLARATION OF CONFORMITY PROCEDURE Responsible Party Philips BU PC Add Ons Address Glaslaan 2 5616 LW Eindhoven Type of Equipment CD Rewriter Model Name Philips CD Rewriter This device complies with Part 15 of the FCC Rules Operation is subject to the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation See user manual instructions if interference to radio reception is suspected FCC INFORMATION U S A 1 IMPORTANT NOTICE DO NOT MODIFY THIS UNIT This product when installed as indicated in the instructions contained in this manual meets FCC requirements Modifications not expressly approved by Philips may void your authority granted by the FCC to use the product
10. isc ejects by itself Make sure that the disc is seated in the tray correctly Incorrect operation of the unit Make sure that the disc is seated in the tray correctly Make sure that you are using the correct disc Make sure that there is no dust dirt or condensation on the disc or tray 18 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 pe 19 Appendix Specifications Interface ATAPI E IDE Data Capacity 650MB 74 minutes disc Record Read Speed Writing CD RW 4X speed Writing CD R Normal speed 4X speed Reading Maximum 32X speed CD DA 1X speed only Data Transfer Rate 150 2400KB sec Burst Transfer Rate Maximum 13 3 MB sec Buffer Size 2MB 325 sectors Access Speed 115 ms Random access at reading Installation Horizontal Disc Loading Tray Audio Out Frequency Response 20 20 000Hz Line Out normal speed Output Level 1 Vrms Line Out Power Consumption 12 7 W peak read write Power Supply 5V 5 12V 10 Environment Temperature 5 C 45 C read write when used in a fan cooled system Humidity 8 80 condensation must not occur Dimensions WxHxD 146 x 41 3 x 193 1 mm excluding front panel Weight 950g Philips reserves the right to change product specifications at any time and without prior notice Thank you for purchasing this fine Philips product We have worked relentlessly to bring you a product co
11. mbining superb operating performance with the greatest possible ease of use If you have any questions or comments please contact your retailer or Philips at the follow ing Internet address Http www pcstuff philips com Troubleshooting 19 Oo
12. na lead in is 300 ohm ribbon lead change the lead in to coaxial type cable If these corrective measures do not produce satisfactory results please contact the local retailer authorized to distribute this type of product If you can not locate the appropriate retailer please contact Philips This manual applies to the Philips CD Rewriter The Philips CD Rewriter front panel displays the Philips brand Philips CD Rewriter 1 Oo cd rom BASIS UK_400nw 11 08 1999 10 45 pene 2 WARNING Warning The temperature where your Philips CD Rewriter is located should be between 5 C and 40 C 41 F 104 F when used in a fan cooled system To reduce the risk of electric shock do not disassemble the Philips CD Rewriter cabinet Always remove the disc before transporting your Philips CD Rewriter IMPORTANT PRECAUTIONS Important Precautions Please read the following precautions before attempting to operate your Philips CD Rewriter Always record in a dust free environment If the disc must be removed from the Philips CD Rewriter before recording is finished store the disc in a clean dust free environ ment Your Philips CD Rewriter contains no user serviceable parts Please refer all servicing to qualified personnel If any of the following should occur your Philips CD Rewriter should be serviced by qualified personnel Metal objects or liquids get inside the Philips CD Rewriter Your Philips CD Rewriter does not operate normally
13. or a marked change in perfor mance is noticed Do not place heavy objects on the CD RW discs Do not subject your Philips CD Rewriter and computer to impact or shock when in use as this may impair recording or playback Philips is not responsible for any data or information losses resulting from the operation of your Philips CD Rewriter 2 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 asin 3 Table of Contents INtPODUCHION once ii cnc ihotid odes eladGG aati EA 4 Philips CD Rewriter Features sys csscadecdeaee hanes sane betaeeeleme nie ea 4 Recording Modes 3 sc ddnoettiadiepe beeen d se kotawa angie shoe d gamete s 4 4 Read mie HSE aiene oaii A EAE S E E N a aed arate NOAA 5 Chapter 1 System Configuration aasre e eee eee 6 Computer ce hapa hd bigs dred E A E eE EE EE E EE cles 6 SOWA e a E A E A Ea E E E E E E x ant 6 Tool reeg iian love noes RAA SEEE AE E aa DNE E ARS 6 DISES pa E E a a E Eero Send A E E EAA 7 Chapter 2 Installing your Philips CD Rewriter Drive 8 MASTER SLAVE settings cs 0200 o2ekeeeee be tran kint TIREI OCE pees a 8 Installing your Philips CD Rewriter drive 0 e eee eee eee eee 10 Chapter 3 Operation 0 ccc ccc ce eee eee e eee 15 rome Panel neger bea cevaiecs rpari T ET R fs AE AREE E 15 Loading a DISC riene sesini se chrarepentuetted duces a ala e a a ESS 16 JOC the Dist oaie n rape abea aa E e e N Eo 17 Manual Ejec
14. re recorded or previously recorded PacketCD written disk proceed directly to your Windows explorer VY In ALL cases give the system enough time to initialize the process Your CD RW drive s LED will blink during the initialization phase and will remain on when finished Keep in mind that a CD R or a CD RW disk stores up to 650mb of data The more data written on the CD the longer it will take to load the disk Read me first 5 cd rom BASIS UK_400nw 11 08 1999 10 45 pene 6 Chapter 1 System Configuration Before using your Philips CD Rewriter make sure that you have all of the items on the list of included items In order to use your Philips CD Rewriter you will require the following Computer The following operating environment is required e An IBM AT compatible computer with a 100 MHz or faster Pentium Processor 16Mb of RAM e A vacant IDE interface connector eA vacant half height bay e Windows 95 Windows 98 Windows NT4 0 or Higher e Sufficient free hard disk space min 12Mb Note You will need about twice as much space on your hard disk as that required by the data you wish to write to CD Software The Philips CD RW software packed with your Philips CD Rewriter has been carefully designed to give you the best possible results with the maximum ease of use Tools Cruciform screwdriver pe This is used to remove the cover of your computer and to install your Philips CD Rewriter drive Cruciform Screwdriver
15. t emergency use sico ccc ca seaind ey ie naai eee Eea 17 Troubleshooting i520 ences kang te bbe ee ce ine ERS bob bea eee eee EAs 18 Appendix 6 oii swe case ee ninna sada AIEEE OPER es ade Ra eR Cee Ee 19 SPECHICAHONS 4 os Re iad ss eas esutenondedend Oued aie EER O a 19 1999 Philips Consumer Electronics B V All Rights Reserved This document may not in whole or in part be copied photocopied reproduced translated transmitted or reduced to any electronic medium of machine readable form without prior consent in writing from Philips MS DOS and Windows are registered trademarks of Microsoft Inc Unix is a registered trademark of UNIX System Laboratories All other trademarks are the property of their respective companies Contents 3 Oo cd rom BASIS UK_400nw 11 08 1999 10 45 pame 4 Introduction Thank you and congratulations for purchasing this Philips Philips CD Rewriter drive Please read this manual before using the drive in order to make the best use of its superior functions After reading we suggest you retain this manual for future reference Philips CD Rewriter Features 4 speed Recording Rewritable 4 speed Recording Recordable 32 speed Reading Your Philips CD Rewriter is able to write overwrite CD RW discs at up to four speed and is able to write CD R and CD RW discs at up to four speed For both types of media this drive is able to read at up to 32X speed Compatible with Seven Different Formats
16. ter 5 Slide your Philips CD Rewriter into the drive bay from the front At this time be careful not to apply excessive force to the drive itself Finger tighten the four fastening screws and check that there is enough room to connect the power supply cable IDE interface connector and the AUDIO cables Chapter 2 Installing your Philips CD Rewriter 11 oO cd rom BASIS UK_400nw 11 08 1999 10 45 pae 12 6 Connect the IDE interface connector Connect the 40 pin IDE interface connector to the IDE interface located on the rear panel of your Philips CD Rewriter drive Position the connector so that the colored line is at pin 1 your lower right 7 Connect the AUDIO cable Connect the single 4 pin connector Sound Blaster compatible to the sound card Connect the 4 pin connector at the other end of the cable the larger connector to the AUDIO OUT connector on your Philips CD Rewriter drive AUDIO cable REE To the Philips CD Rewriter 4 pin connector large To the Sound Card Sound Blaster compatible One of the 2 connectors 12 Philips CD Rewriter Oo cd rom BASIS UK_400nw 11 08 1999 10 45 pae 13 8 Connect the power supply cable Connect the 12V and 5V 4 pin power cable to the power supply interface located on the rear panel of your Philips CD Rewriter drive The shape of the connector makes it impossible to reverse the connections If you have difficul
17. ty when inserting the connector try gently wiggling the connector left and right while inserting it Chapter 2 Installing your Philips CD Rewriter 13 oO cd rom BASIS UK_400nw 11 08 1999 10 45 pae 14 10 11 12 13 Re attach the cover to the computer Connect the power cable to an AC outlet and switch on your computer Make sure that the LED located on the panel of your Philips CD Rewriter drive is lit Start up your operating system For the procedure refer to the manual for your operating system Install your Philips CD recording software For the installation procedure refer to the easy installation instructions on the CD ROM sleeve or simply insert the software CD in your computers CD ROM drive The software installation process will then begin automatically just follow the on screen prompts In addition a complete user manual for the software is located on the CD ROM in the root directory under Manual Simply click on the language you wish to use 14 Philips CD Rewriter cd rom BASIS UK_400nw 11 08 1999 10 45 pe 15 Chapter 3 Operation Front Panel PHILIPS MultiRead WRITING DISC IN 1 Disc tray The disc is inserted and ejected here Pressing the eject button will open the tray 2 Headphone jack This stereo mini jack allows you to connect headphones and listen to audio CD output 3 Headphone volume control wheel
Download Pdf Manuals
Related Search
Related Contents
Nikon Coolpix 995 Digital Camera Installation manual VZ-C12 und VZ-C32 Englisch und Samsung GT-C3310 Felhasználói kézikönyv Comtrol RocketLinx ES8510-XTE Clarion DXZ525 User's Manual Copyright © All rights reserved.
Failed to retrieve file