Trident PDW Manual
Contents
1. iswitch on the airsoft gun in the safe position DO NOT ENGAGE THE TRIGGER WHILE SWITCHING BETWEEN WARNING u MODES ON THE FIRE SELECTOR RETRACTABLE STOCK 1 To extend depress the stock release button A and pull the retractable stock B to its rear most position 2 To retract depress the stock release button A and push the retractable stock B to its forward most position BATTERY INSTALLATION i ENSURE THAT THE STOCK IS IN THE FULLY EXTENDED POSITION i BEFORE OPENING THE STOCK COVER DO NOT REMOVE THE STOCK WARNING COMPLETELY FROM THE GUN 1 Extend the retractable stock A and remove the allen screw B from the stock using a 2 5mm allen key D 2 Remove the stock cap C 3 Connect a small battery E to the connector 4 Curl the connection wires against the side of the battery and insert together into the stock 5 Replace the stock cap and secure with the allen screw using the 2 5mm allen key HOP UP SYSTEM The advanced KRYTAC rotary Hop Up unit is a standard feature in the Trident series AEGs Proper adjustment of the Hop Up will allow the AEGs to fire in a variety of shooting environments to obtain optimal BB trajectory Hop Up Adjustment 1 Pull the charging handle A rearward locking the bolt plate B This will provide access to the Hop Up adjustment dial C 2 Turn the dial up or down an audible click will confirm each a2. KI2Y TAC OWNER S MANUAL TRIDENT TABLE 5 Safety Rules aoi tal secre cac 2 Contact Imformation 4 Technical Specifications nisesh 5 Package Contents syrgas cei 6 Loading the Magazine sss rieien aiaeei eea i iai 6 Fire Selector Switch ise cede i i ede 7 Retractable Stock inani IB RERO cedi EE 7 Battery Installation LUIS ere e beoe ee 8 inler 9 Clearing Jammed amp perit Finit End eene aeri edebant ets 10 Disassembly em 11 Assemb E 12 Cleaning and Maintenance u SN as NOS rere uie 13 Operating Under Harsh Conditions seem 15 Tro ble Shooting G de 2 u uu u u tt rent ret rore tne rhone 16 Component Diagrams and 115 6 17 SAFETY RULES Please read the entire KRYTAC manual before operating the airsoft gun This manual covers important safety operational and maintenance topics It is important that the user reads and understands the manual in order to safely handle and operate the air soft gun Failure to follow the safety guidelines and or operational instructions in this manual may result in serious personal injury or damage to the airso
3. PROCEDURES 1 Wipe down the external parts of the gun and remove any dirt and debris 2 Disassemble the airsoft gun as described in the Disassembly section and pull out the barrel and Hop Up assembly A 3 Pull back the Hop Up adjustment wheel B and lift the Hop Up adjustment lever C up 4 Take a lint free cleaning patch D and place it through the looped end of the cleaning rod E WARNING DO NOT ADD OIL TO THE HOP UP BUCKING EXCESSIVE OIL ON THE HOP UP BUCKING MAY NEGATE THE HOP UP DECREASING RANGE AND ACCURACY 13 CLEANING AND MAINTENANCE 5 Run the cleaning rod through the barrel from back to front in the same direction that BBs travel U TRACK OF THE BARREL SPRING F IT CAN SEPARATE FROM WARNING THE BARREL ASSEMBLY 6 Pull back on the Hop Up adjustment wheel and lower the Hop Up adjustment lever back into position 7 Reinsert the Hop Up barrel assembly into the receiver and reassemble as described in the Assembly section 14 OPERATING UNDER HARSH CONDITIONS When operating under harsh conditions special maintenance may be required to match the climate conditions of a specific operational area Dust and Sand In harsh dusty or sandy environments excessive debris can cause malfunctions and or excessive wear on parts Keep the gun covered and protected while not in
4. Krytac Trident Mechbox 1 Joules with 8 mm Bearing RATEOFFIRE 20 RPS SPECIAL FEATURES E a 2 E PT un TM 41224 2 E dd Nue Integrated FET system licensed by DEFIANCE 2 x 5 1 Trident PDW airsoft gun 1 User s manual 1 Magazine 1 Cleaning rod 1 2 5 mm Allen wrench LOADING THE MAGAZINE High Cap 1 Place the hi cap magazine with the trap door A facing upward Open the trap lt 9 door dispense BBs into the BB well AOS 2 When close the trap door and turn the winding wheel B forward until the clicking changes tone x DO NOT OVER LOAD THE WARNINE MAGAZINE 1 Using a speed loader or other magazine loader insert the nozzle into the opening of the magazine 2 Press down on the loader plunger to load BBs into the magazine 3 Stop once the magazine is full do not force more into the magazine FIRE SELECTOR SWITCH SAFE MODE SEMI AUTO MODE SEMI ee SAFE AUTO FULL AUTO MODE When in safe mode the While in semi auto trigger will not engage mode the airsoft gun and the airsoft gun will will only fire one shot for not fire each time the trigger is engaged In full auto mode the gun will continuously fire as long as the trigger remains engaged SAFETY It is advised when you are not ready to fire keep the fire selector
5. NS 001 491 S RN 0 KA001 10U KA001 68U S 9 KA001 39U 2 a 001 951 f 2 0 Q E D KA001 70U o KAQ01 69U A001 84U Q KA001 22U KA001 84U KA001 50U KA001 59U KA001 73U w KA001 27A e KA001 81U KA001 82U KA001 08U KA001 82U KA001 82U E KA001 08U Qa KA001 75U KA001 82U e KA001 81U 20 COMPONENT LIST PDW PART KA001 00U GEARBOX CONTACT SELECTOR dA SEDED N PISTON RACK 0 2 SELECTOR TRANSFER AXIS GEAR SELECTOR TRANSFER GEAR SELECTOR TRANSFER GEAR SCREW GEARBOX SHELL SCREW LONG 6 GEARBOX SHELL SCREW SHORT 4 ANTI RELEASE LATCH BUSHING COMPONENT LIST PDW CRUSH WASHER O RING KA018 01U HOP UP CHAMBER ASSEMBLY MAGAZINE RELEASE KA018 10U TENSION SPRING KA00228U MAGAZINE RELEASE BUTTON KA019 00U MOTOR RECEIVER PIN CAP SCREW 2 PISTOL GRIP SCREW 2 CHARGING HANDLE SCREW MOTOR PLATE SCREW 2 KA002 60U CRUSH WASHER KA005 02U BARREL NUT KA005 10U RAIL 5 INCH KA008 01U FLASH HIDER KA008 02U SET SCREW KA013 01U PDW OUTER BARREL SDP BATTERY HOUSING ASSEMBLY KA013 25U PDW GAS TUBE 22 www krytac com Copyright 2014 KRISS USA Subject to change V 01 R 2014 12 05
6. and clear of any obstructions prior to firing the airsoft gun Failure to do so may cause a malfunction and in some cases damage the airsoft gun KEEP THE SAFETY ON Keep the fire selector set to safe until your sights are aligned on target and you are ready to fire SAFETY RULES FAILURE TO FIRE If the airsoft gun fails to fire misfires or malfunctions do not look into down the barrel of the airsoft gun BBs can jam in the chamber and can launch suddenly while under pressure causing serious injury MAINTAIN YOUR AIRSOFT GUN PROPERLY Maintaining your airsoft gun as outlined in the manual ensures that your airsoft gun will be safe to shoot and perform to its designed specifications Alterations modifications or adjustments may damage your airsoft gun making it unsafe to shoot and or voiding all warranty claims STORAGE AND TRANSPORT Keep the fire selector on the airsoft gun set to safe with the magazine and battery removed when storing your airsoft gun Always store your airsoft gun in a safe place and out of the reach of children When transporting your airsoft gun make sure that it is in a designated airsoft gun case Never brandish your airsoft gun in public IT IS YOUR RESPONSIBILITY TO SAFELY STORE AND WARNING TRANSPORT YOUR AIRSOFT GUN ORANGE TIP Any alteration of the coloration or markings required by state and or federal law may be deemed illegal in a court of law All risks and responsibility of any alterat
7. ASSEMBLY i Before opening up the receiver remove the magazine and fire the NOTE U airsoft gun in a safe direction to ensure that the Hop Up chamber is i clear of any BBs 1 Set the AEG to safe mode 2 Disconnect and remove the battery see Battery section for instruction 3 Pull the charging handle rearward to lock the bolt plate back 4 Remove ONLY the front from the receiver 5 Slide the upper receiver forward and away from the lower receiver The bolt catch lever B may fall off of the lower receiver when separating the receivers Avoid turning or jostling the lower receiver to help prevent loss of the bolt catch lever DISASSEMBLY 6 Slide the Hop Up and inner barrel assembly C out of the upper receiver O o ROS E y ASSEMBLY 1 Insert the Hop Up and inner barrel assembly into the upper receiver 2 Ensure that the bolt catch lever is in place then slide the upper receiver back onto the lower receiver 3 Reinstall and secure the front body pin CLEANING AND MAINTENANCE i WHILE POINTING THE AIRSOFT GUN IN A SAFE DIRECTION REMOVE THE MAGAZINE AND CYCLE THE GEARBOX UNTIL NO NOTE BBS EXIT THE INNER BARREL PLACE THE AIRSOFT GUN IN SAFE MODE AND DISCONNECT THE BATTERY PRIOR TO ANY CLEANING
8. agazine Contact customer service for professional care COMPONENT DIAGRAM PDW 002 32 KA002 27U KA002 i KA002 37U gu EE ME 002 170 f lt KA002 03U KA002 39U 2 go G KA002 39U 6 KA002 28U oe 002 460 KA002 05U 002 29 002 440 2 C SES Zo 002 58 KA002 44U 17 COMPONENT DIAGRAM PDW KA018 01U Co KA018 07U KA013 24U L 155mm KA013 25U 002 561 KA018 10U 002 481 002 490 1 5 002 490 002 621 8 KA002 51U CT KA013 01U Ko KA005 07U 8 KA008 02U KA005 07U 18 COMPONENT DIAGRAM GEARBOX KA001 57U 001 310 KA001 32U oj 001 170 9 KA001 40U KA001 88U O KA001 16U 001 31 0 vv 001 04 5 KA001 37U KA001 35U KA001 37U KA001 35U Gy KA001 37U Q T KA001 03A KA001 35U 9052 S 7 KA001 37U 001 350 j KA001 05A KA001 35U KA001 37U KA001 3su 9 KA001 87U KA001 87U KA001 87U KA001 87U KA001 56U KA001 85U P KA001 55U KA001 86U g KA001 86U KA001 86U KA001 86U KA001 86U KA001 86U 19 COMPONENT DIAGRAM GEARBOX b KA001 53U KA001 45U KA001 54U KA001 83U KA001 01A AUN A J E KA001 76U KA001 80U SQ KA001 24U Y cy KA001 19U
9. djustment 3 Increasing the number on the dial will increase the amount of Hop Up on the BB Decreasing the number will lower the amount of Hop Up on the BB 4 Once the Hop Up has been set depress the bolt catch release D to return the bolt plate back to its fully seated position HOP UP SYSTEM Excessive Hop Up Airsoft BB travels in an extreme upward trajectory Decrease the Hop Up Ideal Hop Up Airsoft BB travels in a long horizontal flight path Insufficient Hop Up Airsoft BB travels a short distance in a downward trajectory Increase the Hop Up Insufficient CLEARING JAMMED BBS 1 Disassemble the airsoft gun and remove the inner barrel assembly A see 11 for disassembly instruction 2 Lift the Hop up lever B from the inner barrel assembly refer to step 3 of pg13 3 Take the cleaning rod C and insert the unjamming side from the front of the barrel through to the rear to clear out the jammed BB 4 Look through the barrel to ensure that it is cleared 5 Reassemble the airsoft gun see pg12 for assembly instruction iw j It is important to remember that all KRYTAC airsoft guns are made with high quality precision barrels use only new quality airsoft BBs Never NOTE i use recycled or low quality airsoft BBs doing so may cause excessive i jamming In most cases it can severely damage the internal gearbox and or Hop Up and inner barrel 10 DIS
10. ery Semi Auto feature not working at all Disconnector is not engaged properly Reset the disconnector by setting the selector to safe then to automatic then to semi Firing cycle slowing down Battery is low on power Charge or replace battery High pitch or grinding noise Motor level is not adjusted properly Contact customer service for professional care BB travels upward Hop Up adjusted too high Dial down the Hop Up adjustment BB travels downward Hop Up adjusted too low Dial up the Hop Up adjustment BB double feeding or rolling out of the barrel Excessive grease or oil in the hopup chamber Hop Up unit is turned off Fire at least 200 rounds to eliminate excessive grease from the chamber Clean Hop Up unit with supplied cleaning rod Turn Hop Up unit on Hop Up unit can t be adjusted Hop Up adjustment arm is not set properly Reset Hop Up adjustment arm See page 13 sect 6 for reassembly Inner barrel is jammed or jamming Hi Cap magazine not feeding Use of recycled or low quality BBs Inner Barrel is contaminated with BBs or debris Magazine has not been wound BBs are lodged inside the magazine Internal obstruction Use only KRYTAC branded or other high quality BBs Clear and or clean inner barrel with supplied cleaning rod See page 10 for clearing jam section and page 14 for cleaning and maintenance section Wind wheel underneath m
11. ft gun Safety Guidelines EYE PROTECTION Always wear eye protection while shooting operating and maintaining your airsoft guns FIREARM SAFETY RULES Always assume that the airsoft gun is loaded Never assume the chamber is empty based on memory or from someone else s word An airsoft gun can still fire with the magazine removed KEEP YOUR FINGER OFF THE TRIGGER Remove your finger from the inside of the trigger guard until your sights are aligned on target and you are ready to fire MUZZLE CONTROL Always keep the muzzle of the airsoft gun pointed in a safe direction Never point the airsoft gun towards anything you do not intend to shoot KNOW YOUR TARGET AND ITS SURROUNDINGS SAFETY DISTANCE Take note of objects in front of and beyond your target Airsoft guns can shoot up to and beyond 150 feet and may travel further than intended without an adequate backstop Never shoot an airsoft gun directly at targets such as rocks glass water or other hard surfaces that may ricochet BBs in unpredictable directions SAFETY IS YOUR RESPONSIBILITY WARNING The KRYTAC airsoft gun is designed and manufactured to KRYTAC s high standards It was carefully inspected before it was packaged and shipped from our factory It is the sole responsibility of the user for its safe use and handling This airsoft gun is safe unless handled irresponsibly or misused BEWARE OF BARREL OBSTRUCTIONS Ensure that the barrel of your airsoft gun is free
12. ion to the product will be assumed by the operators owners and or user of the product THE ORANGE TIP DOES DISTINGUISH YOUR AIRSOFT GUN AS A TOY ALWAYS TREAT YOUR AIRSOFT GUN AS IF IT WARNING IS REAL FIREARM HAZARDS OF BEING MISTAKEN FOR A REAL FIREARM Due to the nature and design of some airsoft guns they may be mistaken as a real firearm It is strongly advised to operate an airsoft gun in the safety and privacy of your own home or at a legally sanctioned location or game field Police Peace Officers and Law Enforcement Officers are trained to treat objects that resemble a firearm as one In the event that you are approached by a Law Enforcement Official completely comply with their instructions Never point an airsoft gun at a Law Enforcement Official Confrontation with a Law Enforcement Official may result in serious injury or death ALCOHOL MEDICATIONS AND DRUGS Do not handle or operate your airsoft gun while under the influence of alcohol medication or drugs that may impair judgment CONTACT INFORMATION For additional troubleshooting information or questions regarding KRYTAC customer service Call M F 07 30 16 30 Pacific Standard Time at 1 855 KRISS US 574 7787 Submit a contact form at www krytac com Email us at customerservice krytac com SPECIFICATIONS TRIDENT PDW e CALIBER C VELOCITY 86MM 98 MPS 323 FPS with 0 20g BB d ENERGY OUTPUT gt i
13. use When performing maintenance use lubrication sparingly as it tends to attract dirt and other particles After use in a dusty or sandy area always field strip the gun as outlined in the Disassembly section cleaning all the areas that can be reached with a soft clean lint free cloth Heavy Rain Never submerge or expose your gun to extremely wet environments Exposure to such conditions may cause electrical failure and fluid to build up inside the gearbox Dry completely with a clean lint free cloth and clean inner barrel when necessary 15 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE amp i WHEN TROUBLESHOOTING FOLLOW THE SAFETY MEASURES DESCRIBED IN THIS MANUAL WARNING SYMPTOMS CAUSE SOLUTIONS Change selector to Semi Auto or Full Seley eue Automatic Mode 2 tornei Not firing No sound pem Loose connection Contact customer service for professional care Motor is running but not firing Inspect magazine Check if magazine is properly loaded into the gun Ensure magazine is loaded with ammunition Ensure the hi cap magazine is properly wound Motor or battery is hot after short use Damaged battery Loose connection terminal Inspect and or replace battery Contact customer service for professional care Semi Auto feature not functioning properly Battery voltage or discharge is too high Condition or replace batt
Download Pdf Manuals
Related Search