EnGenius® Quick Installation Guide
Contents
1. EnGenius sue EAP600 Wireless N 300 300Mbps Long Range Ceiling Mount Dual Concurrent AP Please verify contents of the box before continuing to set up the EAP600 EAP600 Access Point 12V 2A 100V 240V Power Adaptor RJ 45 Ethernet Cable Mounting Bracket Wall Ceiling Mounting Hardware Kit T Rail Mounting Hardware Kit CD with User s Manual Connecting the EAP600 1 Ensure that the computer in use has an Ethernet Card RJ 45 Ethernet Port For more information verify with User Manual 2 Connect one end of the Category 5e Ethernet cable into RJ 45 port of the EAP600 and the other end to the RJ 45 port on the computer that will use the EAP600 Ensure that the cable is securely connected to both the EAP600 and the Computer 3 Connect the Power DC Inlet to the DC IN port of the EAP600 and the Power to the electrical out AC DC Cable Power Outlet Ethernet Note EAP600 supports both IEEE 802 3at PoE Power over Ethernet and regular power adapter You should use either one as the power source Please do not apply both at the same time IP address configuration 1 After ensuring the EnGenius device is powered on and plugged in ensure that your computer is on 2 For the next steps refer to your Operating System User Manual 3 Once your computer is on ensure that your TCP IP is set to On or Enabled In the control panel double click Network Connections and then double click on the connection of yo2. Select an operating mode from the list Access Point WDS AP WDS Bridge or Repeater and then click on the Apply button C All basic setup is completed Note The wireless connection is not secure To setup security on the EAP600 refer to the EAP600 User Manual Mounting the EAP600 Using the provided hardware the EAP600 can be attached to a ceiling or wall To attach the EAP600 to a ceiling or wall using the mounting bracket 1 Attach the mounting bracket to the wall or ceiling using the provided wall ceiling mounting hardware kit 2 Insert the provided short screws into the bottom cover of the EAP600 Leave enough of the screws exposed to ensure that the unit can be attached to the mounting bracket If extra space is required use the provided spacers and long screws from the T Rail mounting hardware kit to increase the space between the unit and the mounting bracket E a Mounting Screw Mounting Bracket To lock the EAP600 by revolving 3 Mount the EAP600 on the mounting bracket by rotating the unit clockwise about 90 degrees to secure it in place To attach the EAP600 to a ceiling using the provided T rail connectors 1 Attach the T rail connectors to the bottom cover of the EAP600 using the provided short screws Two sizes of T rail connectors are included in the mounting hardware kit 15 16in 2 38cm and 9 16in 1 43cm If extra space is required to accommodate drop ceiling tiles use the provided
3. spacers and long screws P2 6 25 screw J j l 2 Line up the connected T rail connectors with an appropriately sized rail and press the unit onto the rail until it snaps into place T rail Kensington Security Slot Note To protect your EAP600 use the Kensington security slot to attach a cable lock cable lock is not included
4. ur Network Interface Card NIC Select Internet Protocol TCP IP and then click on the Properties button 4 If your PC is already on a computer network ensure that you have set it to a Static IP Address on the interface or Ethernet card that will use the EAP600 as 192 168 1 21 and the Subnet Mask address as 255 255 255 0 Select Use the following IP Address radio button Once the computer has been prepared proceed to setting up the EAP600 EAP600 Setup 1 To configure EAP600 open a web browser example Microsoft Internet Explorer Mozilla Firefox Google Chrome etc 2 Inthe address bar of the web browser enter 192 168 1 1 the default IP address of the EAP600 and hit enter http 192 168 1 1 3 A login screen will appear By default the username of the EAP600 is admin and the password is admin Enter the current username and password of the EAP600 and then click Login Refer to the EAP600 user manual on how to change the username and password NGwenlIus iT 4 After clicking Login with the correct username and password the EAP600 Main Menu will appear If you are successful proceed to setting up the wireless connection Username admin Password eeeee Login Reset Switching Between Operating Modes This device can operate in the following modes Access Point WDS AP WDS Bridge and Repeater A Click on the Operation Mode link under the System navigation drop down menu B Operating Mode
Download Pdf Manuals
Related Search