Dexxo Optimo RTS
Contents
1. Use a 24 V 21 W E13 socket light bulb 24 V 21 W max Checking The obstacle detection function Every six months check that the door reverses direction when an obstacle prevents the door from closing at least 50 mm above floor level The safety mechanisms cells pedestrian door contact Check correct operation every six months refer to page 4 The back up battery To ensure optimum battery life we recommend that the power to the motor is switched off and the door is operated for a number of cycles using battery power three times a year Battery replacement Keytis Keygo RECYCLING Do not dispose of your scrapped appliances nor your used batteries with household waste You are liable to dispose of all your electronic or electrical equipment waste by relocating over to a dedicated collection point for recycling TECHNICAL SPECIFICATIONS Basic technical specifications Mains power supply 230 V 50 Hz Power consumption on standby 4W Max power consumption 120 W Traction force Peak force 800 N Use 20 cycles per day with a standard rail tested for 36 500 cycles Number of channels that can be memorised 32 Somfy radio frequency 433 42 MHz RTS Integrated light 24V 121 W max E13 so2. buttons remain possible To access programming mode once again repeat the same procedure REFITTING COVERS Fig 31 Position the aerial and fit the covers N To ensure proper remote control range the aerial must be fitted in one of the two positions shown in Figure 31 TECHNICAL SPECIFICATIONS BASIC TECHNICAL CHARACTERISTICS Mains power supply Max power consumption Standby Operation Traction force Peak force Starting force 1 Use Number of Opening Closing cycles per day Max speed Programming interface Operating temperature Travel end limits Electrical insulation Built in lighting Somfy radio frequency Number of channels that can be memorised CONNECTIONS Safety input Type Compatibility Pedestrian door safety input Wired control input Amber light output Accessory power supply output Remote aerial input Backup battery input Autonomy OPERATION Forced operation mode Independent lighting control Lighting time delay after movement Amber light pre warning Safety input operation While closing Before opening Dangerous Movement Area Accessible to the Public Built in obstacle detection Operation after obstacle detection Progressive start up Opening speed Closing speed Closure approach speed Dexxo Optimo RTS 230 V 50 Hz 4W 120 W 800 N 650 N 20 cycles per day max tested for 36 500 cycles 14 cm s 4 buttons 4 indicator lights 20 C 60 C indoor dry IP 20 Mechanical sto
3. 2 Special screw for plastic 3 5x12 6 2 Ceiling bracket 21a 1 Single part rail T 2 Motor head bracket 21b 1 Two part rail 8 1 Manual release cord 21b1 1 Sleeve 9 1 Link arm 21b2 8 Self shaping 4x8 screw 10 1 Travel stop 22 2 HM6 self locking nut 11 4 Chain retainer pad 23 2 Bracket 12 1 Power cable 24 1 Spacer 13 4 Hex head M8x16 bolt 25 2 Keytis Keygo remote control 14 4 Hex head M8x12 bolt amp washer 26 1 24 V 21 W E13 socket light bulb Area of application Fig 2 Types of doors fig 2 A Projecting up and over door B Sectional door if the door s upper profile is a specific one use the sectional door mounting bracket ref 9009390 C Sideways opening sliding door for side wall mounting use a belt transmission rail an adjustable cranked arm ref 9014481 for ceiling mounting use an articulated arm ref 9014482 2 Door dimensions Fig 2 For maximum door heights the motor travel can be optimised By installing the motor head at a 90 angle Fig 6 O By fixing the lintel bracket to the ceiling behind the lintel itself by up to 200 mm Fig 4 a By cutting the link arm to size POINTS TO CHECK PRIOR TO INSTALLATION Preliminary checks Check the garage door can be operated manually and runs smoothly Ensure the door is in good mechanical condition pulleys mounts and is correctly balanced spring tension N Remember that any work perfor
4. O standard N l cnh slis s i POON FON BER BOS P1 Closure approach speed 1 w ralo d ai P1 1 no slowdown before closure P1 2 speed is reduced during the last 20 centimetres SE SE P1 3 speed is reduced during the last 50 centimetres 3 87 8 8 long soft stop If this setting is changed it is essential to run the force measurement sequence at the end of the installation procedure Memorising the remote control for partial opening cycle Fig 25 Memorising the remote control for controlling lighting Fig 26 Memorising a Telis or similar type remote control Fig 27 SPECIAL OPERATION Refer to the User s Manual CLEARING REMOTE CONTROLS AND ALL SETTINGS Clearing remote controls Fig 28 Press the PROG button until the light blinks 7 s This clears all of the remote controls memorised Resetting all settings Fig 29 Press the SET button until the light goes out 7 s This clears all previously stored settings and returns them to their default values LOCKING PROGRAMMING Fig 30 Used to lock the programming settings end limit setting self learning setup Simultaneously press the SET and buttons Start by pressing SET pressing and must take place within two seconds Pressing the SET button then no longer has any effect The remote control memorising functions PROG button and forced mode operation
5. flash for 30 seconds during this process Pedestrian door safety function Opening a pedestrian door within the garage door will prevent the door from moving The light will flash for30 seconds during this process Flashing amber light The amber light comes on whenever the door moves with a two second advance warning before the start of door motion Working from the back up battery lf a back up battery is installed the Dexxo ptimo RTS motor will operate when a power cut occurs The following conditions apply to operation Door speed is reduced The light will not come on The safety devices are disabled Battery specifications Endurance the battery will last for 24 hours with a maximum of 5 to 10 operating cycles depending on the weight of the door Recharging time 48 hours Service life prior to replacement approx three years To ensure optimum battery life we recommend that the power to the motor is switched off and the door is operated for a number of cycles using battery power three times a year Forced operation mode Fig 10 This function is used to move the door at any time remote control lost safety mechanism failure etc Remove the built in lighting cover Control door motion using the and buttons Pressing and holding the button will trigger closure Pressing and holding the button will trigger opening PERIPHERALS A number of peripherals are
6. with a manual release mechanism so that you can move the door manually should a power failure occur for example The manual release mechanism should be easily accessible and located no more than 1 80 metres above floor level 1 Disengaging the motor drive mechanism Pull on the manual release cord until the door drive mechanism is disengaged 2 Manually moving the door This is possible as long as the door drive mechanism is disengaged 3 Reengaging the motor drive mechanism Move the door manually until the drive mechanism comes to reengage itself into the transmission rail N When disengaging the motor drive mechanism use caution for a badly balanced door may cause sudden door movement that may be dangerous Only use the cord to disengage the motor drive mechanism Never use the cord to move the door manually Always reengage the motor drive mechanism before sending another command to the motor drive unit Special operation Depending on the peripherals installed and the operating options set by your installer the Dexxo Optimo RTS system may perform the following special operations Full opening cycle using Telis or similar remote controls Fig 9a Safety photoelectric cell operation An obstacle detected between the cells will prevent the door from closing The door will stop and then reopen when an obstacle is detected during the close cycle The light will
7. available Key Description Comments 1 Keytis 2NS RTS remote control Hand held 2 channel remote control 2 Keytis 4NS RTS remote control Hand held 4 channel remote control 3 KEYGO remote control Four channel keyring remote control 4 RTS pushbutton Wall mounted 2 channel remote control switch 5 RTS radio code keypad Access code control point For use outside the garage 6 Photoelectric cells To prevent door closure if an obstacle is detected 7 Amber light To signal a warning when the door operates 8 Keyswitch Keyswitch for secure control 9 Battery To provide continued operation during a power cut 10 Release lock To engage the manual release system from the outside using the existing door handle Highly recommended when the garage door is the only access point into the garage 44 G lki released i engage the manual release system from the outside using the existing door handle ighly recommended when the garage door is the only access point into the garage 12 Door locking kit A system to reinforce door locking MAINTENANCE Replacing the bulb in the light unit Fig 12 1 2 Remove the light cover 3 4 Unscrew and replace the defective light bulb 5 6 7 Refit the light cover
8. cket Operating temperature 20 C 60 C
9. earning When the door is moving pressing any button will stop the movement and stop the self learning mode When the door is stopped pressing SET until the light comes on and the an indicator light comes off 2 s will exit the self learning mode The self learning mode can be called up at any time even after the self learning cycle has been completed Memorising remote controls for full opening cycle Fig 16 Up to 32 control channels can be stored Running this procedure for a previously stored channel will clear it At this stage in the installation process the Dexxo Optimo RTS motor drive unit is ready to run OPERATING TEST Using the remote controls Fig 17 Obstacle detection function Fig 18 and 19 The detection of an obstacle during door opening will stop the door Fig 18 The detection of an obstacle during door closure will reopen the door Fig 19 Make sure that obstacle detection works when the door encounters an obstacle 50 mm from the ground Built in lighting operation The light will come on every time the motor drive unit is operated It will go out automatically after one minute once the door stops Repetitive use which causes the light to stay on continually may result in an automatic cut off condition triggered by the thermal cut out protection mechanism CONNECTING PERIPHERALS Description of the various peripherals Fig 20 Key Description Amber light Code keypad Keyswitch Aerial Ba
10. ep the remote controls out of reach of children Fig 2 When replacing the light bulb select a 24 V 21 W E13 type Fig 3 Regularily check the operation of the door to identify any sign of wear deterioration or incorrect balancing Do not operate the door if repairs or adjustments are required Remain at a safe distance when operating the door PRODUCT PRESENTATION Description Fig 4 The Dexxo Optimo RTS system is designed to power garage doors in residential use This motor drive system comprises Amotor head 1 with integrated light 2 Arail assembly 3 with a manual release cord 4 OPERATION AND USE Normal operation Full opening cycle using Keytis or similar remote controls Fig 5a Obstacle detection operation Fig 6 and 7 When an obstacle is detected during the open cycle the door will stop Fig 6 When an obstacle is detected during the close cycle the door will stop and then reopen Fig 7 Once an obstacle has been detected the light will flash for 30 seconds Light operation The light will come on each time the motor drive unit is operated The light will go out one minute after the door stops moving Repetitive use that causes the light to be continually on may result in a thermal cut out this will automatically turn the light off Manual release cord operation Fig 8 Dexxo Optimo RTS is fitted
11. g 12 For chain rails only These pads are used to limit spurious noise linked to chain friction within the rail Position each of the pads in the first hole in the rail after the travel stop Make sure that the pad is pressed in all the way so that its positioning pin is accessible outside of the rail Checking the chain or belt tension Fig 13 The rails are supplied ready tensioned and inspected If necessary adjust the tensioning N The rubber or tension spring must never be full compressed during operation Connecting the mains power supply Fig 14 1 Remove the motor cover and the protective sheet 2 Fit the light bulb 3 Connect to the mains supply N Plug the power cable into a suitable power outlet that complies with electric power requirements The electric supply must be suitably protected a fuse or circuit breaker with a 5 A rating and a residual current device 30 mA An omnipolar disconnection mechanism must be provided for the power supply by using a power cord with a mains splug that can be disconnected or by fitting a switch that ensures a contact separation distance of at least 3 mm for each pole refer to standard EN60335 1 N Make sure that the manual release cord is located at a maximum height of 1 80 metres off the ground If necessary extend the cord PROGRAMMING Programming button description Press for 2 s memorise remote controls Press for 7 s delete remote cont
12. he garage ceiling Fig 7 9 Fitting to the lintel bracket Fig 7 Ceiling mounting Flush with the ceiling mount the system directly onto the ceiling using the rail Fig 8 It is possible to add mounting points at the motor head level Fig 8 O Hung from the ceiling two options mount the system at the motor head Fig 9 O mount the system at the rail Fig 9 To add an adjustable intermediate mounting along the rail or a mounting at a dimension h between 250 mm and 550 mm use the ceiling mounting kit ref 9014462 Fig 9 O Fitting the arm onto the door and the trolley Fig 10 1 Release the trolley using the manual release cord 2 Bring the trolley up to the door 3 Attach the arm to the door bracket and the trolley Adjusting and fastening the opening travel stop Fig 11 1 Release the trolley from the runner using the manual release mechanism and bring the door to the open position Do not open the door fully but position it so that it does not reach its own travel stop 2 Slot the travel stop 10 into the rail then turn it by 90 3 Position the travel stop against the trolley 4 Moderately tighten down the mounting screw Do not tighten the mounting screw all the way down Excessive tightening can damage the screw and cause the travel stop not to remain in place Note Do not use the travel stops supplied with the transmission rail Fitting the chain retainer pads Fi
13. lanced and that it opens and closes correctly Locate all control systems at least 1 5 metres above floor level making sure that they are visible from the entrance to the garage but safe from moving parts Position the manual release cord no more than 1 8 metres above floor level Where a removable release mechanism is used we recommend storing it close to the door Fix the label describing the manual release procedure close to the release mechanism Fix the warning labels describing the hazards of door motion close to any fixed control mechanisms installed and make sure that the labels are clearly visible to the user After installation make sure that the mechanism is correctly adjusted and that the motor drive unit reverses its motion when the door encounters an obstacle that is at least 50 mm from floor level After installation make sure that no part of the door overhangs an area accessible to the public After installation make sure that the motor drive unit inhibits or stops the door opening motion when the door is loaded down with a 20 kg weight attached to a central position of the door s bottom edge PRODUCT DESCRIPTION Product components Fig 1 Key Number Description Key Number Description 1 1 Motor head 15 6 HUB nut 2 1 Motor cover 16 2 Shaft 3 1 Built in light cover 17 2 Circlips 4 1 Lintel bracket 19 4 Self shaping 4x8 screw 5 1 Door bracket 20
14. lb in the light unit Checking Battery replacement TECHNICAL SPECIFICATIONS 6 No MN no no NO KR oo No So un A ol GENERAL PRESENTATION Thank you for choosing a Somfy product This product is designed and manufactured by Somfy in line with quality procedures that are ISO 9001 compliant The world of Somfy Somfy develops produces and sells automation systems for residential and commercial applications Alarm systems automatic blinds and shutters garage doors and gates all Somfy products are designed to fulfill your needs in terms of safety comfort and security At Somfy the quest for quality is a continual process Somfy has built its reputation on the quality of its products and is synonymous with innovation and technological leadership worldwide Support Getting to know you listening answering your needs is all part of the Somfy approach Please contact your local Somfy retailer or installer for details on other Somfy products Internet www somfy com SOMFY SOMFY SAS capital 20 000 000 Euros RCS Bonneville 303 970 230 SAFETY INSTRUCTIONS Standards This product complies with the safety specific rules for powering vertically opening garage doors in residential use requirements standard EN 60335 2 95 When installed in line with these instructions and in compliance with the Installation Checklist the product will be compliant with standards EN 13241 1 and EN 12453 The instruc
15. med on door springs may be dangerous The structure of your garage walls lintel inside surfaces cross members door rails are used to mount the Dexxo Optimo RTS system Reinforce them where necessary Never splash water onto the system Never install Dexxo Optimo RTS in a location where water may cause damage The bottom edge of the door should be fitted with a rubber strip to avoid hard contact and enhance the contact surface If the garage door is the only entry point into the garage fit an external release external release keylock ref 9012961 or an external release ref 9012962 and include a back up battery ref 9001001 If the garage door includes a separate pedestrian door the door must be fitted with an interlock to prevent garage door movement when the pedestrian door is open pedestrian door safety kit ref 2400657 If the garage door opens on to a public road install an indicator light such as a flashing amber light ref 9015171 If the garage door operates in automatic mode install a photoelectric cell type safety system ref 9014994 and a flashing amber light type indicator Make sure that the door does not comprise any accessible parts N Unlocking the door may trigger uncontrolled door movement if the door is not balanced correctly Safety instructions Safety instructions must be complied with throughout the installation process Take off any personal jewellery bracelet chain or others d
16. pper at opening Memorized end limit position at closing Class 2 double insulation O 24 V 21 W E13 socket RTS 433 42 MHz B2 Dry contact NC Photoelectric TX RX cells Dry contact NC Dry contact NO 24 V 15 W with built in flashing control 24 V 500 mA max Yes RTS aerial compatible R f 2400472 Yes battery pack compatible R f 9001001 24 hours 5 to 10 cycles depending on door Charge time 48 hours By pressing and holding the motor control button Yes for built in lighting Fixed 60 s 2 s automatic if light connected Fully reopens None Adjustable sensitivity 4 levels Full re opening Yes Set 14 cm s max Set 12 cm s max Programmable does not slow down short slowdown zone 30 cm long slowdown zone 50 cm 1 Maximum load for motor to start and drive door for at least 5 cm according to RAL GZ definition Dimensions Overall length 3 295 3 895 pa 171 rT Available travel 2 555 3 155 63 6 Fixation 2 982 3 582 Rail 2 900 3 500 Overall length 3 153 3 753 Rail 2 900 3 500 somfy com Dexxo Optimo RTS User Manual CONTENTS GENERAL PRESENTATION 2 The world of Somfy Support SAFETY INSTRUCTIONS Standards Safety instructions ia PRESENTATION OPERATION AND USE Normal operation Special operation ca MAINTENANCE Replacing the bu
17. ring vertically opening garage doors in residential use requirements standard EN 60335 2 95 When installed in line with these instructions and in compliance with the Installation Checklist the product will be compliant with standards EN 13241 1 and EN 12453 The instructions referred to in the installation manual and instructions for use of this product are designed to prevent damage to property and personal injury along with compliance with the above standards Failure to comply with these instructions absolves Somfy from any liability resulting from damage that may be caused Dexxo Optimo RTS is a product that must be installed inside the garage with an integrated back up control system Somfy hereby declares thatthe device is compliant with the essential demands and other relevant requirements of directive 1999 5 CE A declaration of compliance is available from the web site at www somfy com ce Dexxo Optimo RTS This product is suitable for use in the European Union and in Switzerland SAFETY INSTRUCTIONS Caution These are important safety instructions Always follow the instructions incorrect installation may lead to serious injury Safety instructions Before installing the motor drive unit remove all unessential lines or chains and switch off all equipment that is not essential for motorised door operation Before installing the motor drive unit make sure that the door is in good mechanical condition that it is properly ba
18. rols Press for 0 5 s call up and exit the setup menu Press for 2 s start self learning Press for 7 s clear self learning and settings Stop self learning Modifying a setting value Using the forced mode Operation indicator light red Noi 3 End limit setting and self learning indicator light green PO P1 parameters indicator green End limit setting and self learning Fig 15 1 Press the SET button until the light comes on 2 s e The indicator light flashes 2 Control the motor using the or buttons so that the transmission system runner moves to link up with the trolley and closes the door i Pressing and holding the button moves the runner in the close direction Release the button before the motor has time to force against the door Pressing and holding the button moves the runner in the open direction 3 Adjust the closed position using the or buttons Release the button before the motor has time to force against the door 4 Press SET to validate the closed end limit and start the self learning cycle The door runs through a complete Open Close cycle and the indicator light goes out dv f the self learning cycle was completed correctly the h indicator light stays on f the self learning cycle was not completed correctly the h indicator light continues to flash During self l
19. somfy com Dexxo ptimo RTS EN Installation manual Es Manual de instalaci n PT Manual de instala o EL Eyxeip dio eykaTaoTaons HOME 5056739C MOTION BY CONTENTS en PRESENTATION SAFETY INSTRUCTIONS Caution Safety instructions PRODUCT DESCRIPTION Product components Area of application POINTS TO CHECK PRIOR TO INSTALLATION Preliminary checks Safety instructions INSTALLATION Installation height Detailed description of installation steps PROGRAMMING Programming button description End limit setting and self learning Memorising remote controls for full opening cycle OPERATING TEST Using the remote controls Obstacle detection function Built in lighting operation CONNECTING PERIPHERALS Description of the various peripherals Electrical connections for the various peripherals SETUP AND OPERATING OPTIONS General setup diagram Meanings of the various parameters Memorising the remote control for partial opening cycle Memorising the remote control for controlling lighting Memorising a Telis or similar type remote control dinda OPERATION CLEARING REMOTE CONTROLS AND ALL SETTINGS Clearing remote controls Resetting all settings iia PROGRAMMING REFITTING COVERS TECHNICAL SPECIFICATIONS Dimensions SNN N NAN uN uN DDD DDD D aon BD wowwoW oo N wonDY no N N ooo N N GENERAL PRESENTATION This product complies with the safety specific rules for powe
20. tions referred to in the Installation Manual and Instructions for Use of this product are designed to ensure that damage to property and injury to persons is avoided along with compliance with the above standards Failure to comply with these instructions absolves Somfy from any liability for any damage that may be caused Dexxo Optimo RTS is a product that must be installed inside the garage with a built in back up control system Somfy hereby declares that the device is compliant with the essential demands and other relevant requirements of directive 1999 5 CE A declaration of compliance is available from the web site at www somfy com ce Dexxo Optimo RTS This product is usable in the European Union and in Switzerland These are important safety instructions For safety reasons it is important to always follow all instructions Retain these instructions for future reference Safety instructions Every month test that the motor drive unit reverses its motion when it encounters an obstacle that is at least 50 mm from ground level If this is not the case call your installation specialist Always be very careful when using the manual release cord for a manually operated door may fall quickly due to weak or broken springs or if it is badly balanced Before manually operating the door or performing maintenance work always turn the power off and where necessary remove the battery Fig 1 Never let children play with door control systems Ke
21. ttery Pedestrian door safety kit Photoelectric cells CoN OO Oo BR oO Electrical connections for the various peripherals Fig 20 to 22 Cut the electric power supply to the motor before performing any work on peripherals The h indicator light remains off after working on the system check the wiring for possible short circuits or polarity reversals General electrical diagram Fig 20 Pedestrian door safety kit When the pedestrian door contact is fitted it must be connected in place of the jumper normally fitted between terminals 3 and 4 N If the pedestrian door contact is removed the jumper between terminals 3 and 4 must be refitted Photoelectric cells Fig 21 When fitting photoelectric cells connect the receiver cell RX to the input in place of the jumper fitted between terminals 5 and 6 N If the cells are removed the jumper between terminals 5 and 6 must be refitted Code keypad Fig 22 SETUP AND OPERATING OPTIONS General setup diagram Fig 23 Meanings of the various parameters Programming example adjusting the long slowdown zone P1 3 Fig 24 Code Description Values Comments PO Obstacle detection sensitivity If this setting is changed it is essential to run the force measurement sequence at the end of the installation procedure N P qo 1 8 low sensitivity N ly Nhe mee 2 O low sensitivity ir Si NDA 3 6 6
22. uring installation work During drilling and welding work always wear safety glasses and suitable protection Always use suitable tools Take care when handling the motor drive system Never connect the mains power supply or the battery back up system before completing the installation process Never use high pressure water systems for cleaning purposes INSTALLATION Installation height Fig 3 Measure the distance D between the door s highest point and the ceiling If D is between 35 and 200 mm mount the complete system straight onto the ceiling If D exceeds 200 mm mount the complete assembly so that the height H falls between 10 and 200 mm Detailed description of installation steps Fig 4 to 14 Mounting the lintel bracket and the door bracket Fig 4 When installing the system directly onto the ceiling flush with the ceiling the lintel bracket can be mounted on the ceiling if necessary recessed from the lintel by up to 200 mm max Fig 4 Assembling the two part rail Fig 5 1 2 3 Unfold the two parts of the rail 4 Assemble the two parts of the rail using the sleeve 5 Mount the complete assembly using the eight mounting screws The mounting screws must not penetrate the rail do not drill When installing the system directly onto the ceiling do not use the sleeve mounting screws Fitting the rail onto the motor head Fig 6 Fitting the complete assembly onto t
Download Pdf Manuals
Related Search