Manual - Datatail
Contents
1. CLEANING Surface Maintenance Clean periodically with hot soapy water and clean cotton cloth Do not use corrosive or abrasive detergent e g comet powder scrub EZ Off oven cleaner or steel wool scoring pads which will scratch and damage surface For heavier soil use liquid degreaser such as Formula 409 or Fantastic brand cleaner After cleaning you may use non abrasive stainless steel polish cleaners such as 3M or ZEP to polish and buff out the stainless luster and grain Always scrub lightly with clean cotton cloth and with the grain Metal Filters The Metal Filters fitted by the factory are intended to filter out residue and grease from cooking It need not be replaced on a regular basis but are required to be kept clean Filters should be cleaned after every 30 hours of use Use the Filter Clean Reminder function on the controls to determine when filters require cleaning ref page 8 Remove and clean by hand or in dishwasher Spray Formula 409 or equivalent degreasing detergent and leave to soak if heavily soiled Dry filters and re install before using hood Replacing Metal Filters Should filters wear out due to age and prolonged use replace with following part number Hood Model Part No Filters in pkg ZFI M90S ZOF M032 2 Also replace damaged filter that has punctured or broken mesh bent or broken frame 10 MAINTENANCE LIGHTS Replacing Light Bulbs CAUTION Light2. E 1 FT 8 Ifa reducer is used install a long reducer caen a eet transition used 5 FT instead of a pancake reducer Reduce duct Side Wall Cap w damper 30 FT size as far away from opening as possible Roof Cap 30 FT e g 1 roof cap 2x90 elbows 1 45 elbow used 30 30 9 69 used 31 available for straight duct runs If turns or transitions are required Install as far away from opening and as far apart between 2 as possible INSTALLATION DUCTING WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls crawl spaces ceiling attics or garages All exhaust must be ducted to the outside Use Metal ductwork only Fasten all connections with sheet metal screws and tape all joints w certified Silver Tape or Duct Tape Some Ducting Options mn a ON mi side wall cap side wall cap w gravity damper w gravity damper Soffit or crawl space Roof Pitch w Flashing amp Cap INSTALLATION EI SPECIFICATIONS IX I 3 4 Elec K O L 24 4 42 9 A 18 10X 10 47 ELECTRICAL All Electrical work must by performed by qualified electrician or person with similar technical know how and background For personal safety remove house fuse or open circuit breaker before beginning installation Do not use extens
3. 24 27 5 46 Maximum mount height should be no higher than 32 It is important to install the hood at the 15 150 proper mounting height Hoods mounted too low could result in heat damage and fire hazard while hoods mounted too high will be hard to reach and will loose its performance and efficiency Min 24 Max 32 Min 87 5 Max 114 If available also refer range manufacturer s height clearance requirements and recommended hood mounting height above range Minimum ceiling clearance 87 5 at 24 hood mounting height Maximum ceiling clearance 114 at 32 hood mounting height DUCTING A minimum of 6 round or 3 1 4 x 10 ee Minimum Duct Size rectangular duct must be used to maintain Round 6 minimum maximum air flow efficiency Rectangular 3 1 4 x 10 minimum requires a 6 to 3 1 4x10 adaptor not supplied order our Always use rigid type metal ducts only part AK00019 Flexible ducts could restrict air flow by up to 50 Duct Run Calculation Maximum run Also use calculation on right to compute 6 or 3 1 4 x 10 duct 100 FT total available duct run when using elbows transitions and caps Deduct each 90 Elbow used 15 FT ALWAYS when possible reduce the number each 45 elbow used 9 FT or transitions and turns If long duct run is each 6 to 3 14 x 10 required increase duct size from 6 to 7 or transition used
4. and count usage time and indicate when carbon filter replacement is needed every 120 hrs FEATURES amp CONTROLS CONTROLS FILTER CHANGE INDICATOR Carbon Filters Filter Change Reminder Carbon if fitted When your hood is installed as a Purifying Ductless Recirculating unit it is fitted with a set of Carbon Filters to purify exhaust and fumes from cooking and re circulates the air within the home These Carbon Filters are required to be replaced after every 120 hours of use The Filter Change Reminder function in the microprocessor needs to be switched on The microprocessor in the controls when set will elapsed and count usage time and indicate by a flashing E3 when carbon filter replacement is needed every 120 hrs Setting the Filter Change Reminder When Off hold for approx 5 seconds The display will change from exhaust mode to purifying mode hold 5 secs display from lt gt to lt C gt carbon filters used this indicates that the elapse timer function is switched on and Carbon Filters are used Filter Replace Indi ator i When the display starts flashing the Change Filters display lt C gt flashes Carbon Filters requires replacement after 120 hours of use E4 Re setting Function Once filters are replaced with hood off press and hold G the display will appear hold for approximately mae until hold 5 secs display from lt C gt to lt gt on display disappear
5. bulb becomes extremely hot when turned on DO NOT touch bulb until switched off and cooled Touching hot bulbs could cause serious burns Make sure all power is turned off and bulbs are not hot Carefully pry trim w glass off the socket module Replacement bulb w 12V 20W type bulbs WARRANTY TO OBTAIN SERVICE UNDER WARRANTY You must present proof of original purchase date Please keep a copy of your dated proof of purchase sales slip in order to obtain service under warranty One Year Service Repair Warranty For one year from date of original purchase we will provide free of charge service labor to repair any failed parts or components due to manufacturing defects Two Years Parts Warranty For two years from date of original purchase we will provide free of charge non consumable replacement parts or components that failed due to manufacturing defects Consumable parts not covered by this warranty include Light Bulbs Metal and Carbon Filters Who is Covered This warranty is extended to the original purchaser for products purchased for ordinary home use in the 48 mainland states Hawaii and Washington D C In Canada and Alaska this warranty is Limited There might be costs associated with shipping the products to our designated service locations or you might need to pay service technician s travel costs to have the appliance repaired in home This Warranty will b
6. by pressing to decrease and to increase speed level The display indicates level selected Delay Off This is used for programmed shut down of blower and lights 15 minutes after the function is activated Press once a dot flashes in the lower right hand side of display indicating the function is on The hood will completely shut down in 15 minutes O Lights On Off Dim Switch lights On and Off by pressing key once To dim lights press and hold for 2 seconds Advance Display Functions Filters Clean Reminder Metal After every 30 hours of use the display will start flashing an reminding you to clean the metal filters from residue and possible clogs The standard Metal Filters fitted are required to be cleaned frequently and as recommended in order to maintain blower efficiency If improperly maintained residue from cooking will sift through filters and cause damage to hood blowers and other sensitive components and possibly clog duct work and creates fire hazard Filters Change Reminder Carbon if fitted When your hood is installed as a Purifying Ductless Recirculating unit it is fitted with a set of Carbon Filters to purify exhaust and fumes from cooking and re circulates the air within the home These Carbon Filters are required to be replaced after every 120 hours of use The Filter Change Reminder function in the microprocessor needs to be switched on The microprocessor in the controls when set will elapsed
7. OBTAIN SERVICE UNDER WARRANTY or any Service Related Questions please call 1 888 880 8368 Have your product proof of purchase with date ready for warranty issues Or write to Zephyr Corporation Service and Warranty department 1551 Minnesota Street San Francisco CA 94107
8. RS Tap EZ anchor tip into marked drywall locations turn with screwdriver until seated flush ane af Note Whenever possible the hood should be secured to wall studs Use EZ anchors provided only on hollow drywall applications minimum drywall thickness 2 If a stud or wood surface is present fasten anchors with screws directly into stud or plywood For all other wall an types concrete brick tiles etc use appropriate anchors for mounting INSTALLATION Ductless conversion is intended for applications where an exhaust duct work is not possible to be installed When converted the hood functions as a purifying hood rather than an exhaust hood Fumes and exhaust from cooking is drawn and filtered by a set of optional Carbon Filters The air is then purified and re circulated back within the home DUCTLESS CONVERSION We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct work if possible The hood is most effective and efficient as an Exhaust unit Only when the exhaust option is not possible should you recourse to converting the hood into a purifying unit When converted to be a purifying unit a set of Carbon Filters are required on top of its standard Metal Filter set Order according to its Part number below The standard Metal Filters are intended to capture residue from cooking and the optional Carbon Filters help to purify fumes exha
9. USE CARE AND INSTALLATION GUIDE Read all Instructions before Installing and operating this appliance MODEL ZFI M90S IMPORTANT SAFETY NOTICE WARNING Installation The installation in this manual is intended for qualified installers service technicians or persons with similar qualified background DO NOT attempt to install this appliance yourself Injury could result from installing the unit due to lack of appropriate electrical and technical background All electrical wiring must be properly installed insulated and grounded Overly accumulated grease in old duct work should be cleaned out or duct work should be replaced if necessary to avoid the possibility of a grease fire Check all joints on duct work to insure proper connection and all joints should be properly taped Operations Read all instructions in this manual before operating the appliance Save these instructions for future reference Always leave safety grills and filters in place Without these components operating blowers could catch on to hair fingers and loose clothing NEVER dispose cigarette ashes ignitable substances or any foreign objects into blowers NEVER leave cooking unattended When frying oil in the pan can easily overheat and catch fire The risk of self combustion is higher when the oil has been used several times Cleaning The saturation of greasy residue in the blower and filters may cause increased inflammability Keep unit clean an
10. d free of grease and residue build up at all times to prevent possible fires Filters must be cleaned periodically and free from accumulation of cooking residue see cleaning instructions inside Old and worn filters must be replaced immediately Do not operated blowers when filters are removed Never disassemble parts to clean without proper instructions Disassembly is recommended to be performed by qualified personnel only Call our service center for removal instructions The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation maintenance and suitable use of the product The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance CONTENTS INSTALLATION Mount heights amp clearance Ducting Specifications Electrical Mounting the hood Duct cover EZ Anchors Ductless Conversion Carbon Filters FEATURES amp CONTROLS Touch controls amp features Advance display functions Filter change indicator Filter clean indicator MAINTENANCE Cleaning Lights replacement WARRANTY Coverage amp exceptions Ne oar BBW wWw gt 5 6 5 7 INSTALLATION KI MOUNT HEIGHTS amp CLEARANCE II Minimum mount height between range top to hood bottom should be no less than
11. e Voided when Product damaged through negligence misuse abuse accident Improper installation and failure to follow installation instructions When product is used commercially or other than its intended purpose Damaged because of improper connection with equipment of other manufacturers Repaired or modified by anyone other than Zephyr s Authorized Agents What is Not Covered Consumable parts such as light bulbs filters and fuses Services outside of service area and the labor cost incurred in connection with the removal shipping and reinstallation cost nor does it cover any other contingent expenses The natural wear of finish and wear due to improper maintenance use of corrosive and abrasive cleaning products pads and oven cleaner products Chips dents or cracks due to abuse misuse freight damage or improper installation Service trips to your home to teach you how to use the product Damage of product caused by accident fire floods or act of God This warranty is valid in the United States and Canada It is non transferable and applies only to the original purchaser and does not extend to subsequent owners of this product Any applicable implied warranties including the warranty of merchantability are limited in duration to a period of express warranty as provided herein beginning with the date of original purchase at retail and no warranties whether express or implied shall apply to this product thereafter TO
12. ion cord or adapter plug with this appliance Follow National electrical codes or prevailing local codes and ordinances Electrical Supply This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse Wiring must be 2 wire w ground Please also refer Electrical Diagram labeled on product Cable Lock A cable locking connector not supplied might also required by local codes Check with local requirements and codes purchase and install appropriate connector if necessary 4 INSTALLATION INSTALLATION Mounting the Range Hood 1 Measure from range top to hood bottom 24 min Level and mark line A 2 Plum and mark center line 3 Mark mounting height line B 18 1 2 from line A 4 Mark mounting spread from C L 8 A 7 8 5 Fasten E Z Anchors to wall see below as marked 6 Fasten screws provided onto EZ Anchors CIL do not fasten screws all the way 7 Fasten hanging brackets onto hood hang hood on wall and hand tighten fig A Fasten Hanging Brackets provided Mounting the Duct Cover 1 Center and attach duct cover mount bracket on wall below ceiling or soffit 2 Fasten telescopic duct covers onto hood and bracket EZ ANCHO
13. s The Filter Change Reminder is now re set and a new 120 hours elapse cycle is initiated 8 FEATURES amp CONTROLS CONTROLS FILTER CLEAN INDICATOR Metal Filters Filter Clean Reminder Standard Metal Filters fitted Whether your hood is installed as an Exhaust or Purifying unit a set of metal filters are fitted by the factory These Metal Filters are intended to filter out residue from cooking It need not be replaced on a regular basis but are required to be kept clean The Filter Clean Reminder function in the microprocessor will automatically indicate by a flashing fA when the metal filters are needed to be cleaned after every 30 hrs of use Filters can be cleaned by hand or in a dishwasher with non abrasive soap Heavily soiled filters should also be soaked in grease cutting detergent such as 409 or its equivalent prior to cleaning Filter Clean Reminder When flashes on display the metal display lt A gt flashes filters installed are required to be cleaned This will occur after every 30 hours of use Re setting Function Reset the Filter Clean Reminder timer when filters are cleaned and re installed Press and hold for approx 5 seconds the display will appear hold for approximately hold 5 secs display from lt C gt to lt gt 5 seconds until on display disappears The Tea enna Ft is now re set and a new 30 hours elapse cycle is initiated MAINTENANCE EJ
14. usted from cooking for re circulation Carbon Filters Required 1 Purchase ductless Charcoal Filters as follow Hood Model Part No Filters in pkg ZFI M908S ZOF C022 2 2 Remove metal filters on hood Clip carbon filters onto each slot opening Re install metal filters 4 Turn on Filter Change Indicator on control panel refer details pg 7 5 Carbon Filters must be replace after every 120 hours of use or approximately every 2 to 3 months based on the average of 1 2hrs of daily cooking time The microprocessor in the controls when set will elapsed and count usage time and indicate when carbon filter replacement is required every 120 hrs U i be Tl ed ew x 6 straight pipe 6 T connector or 90 elbow wall pipe strap Ducting 1 Install a 6 straight pipe and a T connector or a 90 elbow to divert air through louvers on duct cover 2 You may also order our air diverting duct kit call 1 888 880 8368 6 FEATURES amp CONTROLS TOUCH CONTROLS amp FEATURES Blower On Off Display Speed level Delay Off Indicator Filter Clean Change OS l Lights On Off Hold to Dim Adjust 6 Speed Levels 15 Min Delay Off Blower On Off By pressing the blower is switched On and Off When switched on the blower starts up on speed level 3 Speed Selection The 6 speed levels are selected
Download Pdf Manuals
Related Search