Mania EFX600 user manual
Contents
1. Tilt Pan Mirror Dish Color Gobo Mania EFX600 circuit board layout Shutter 29 TROUBLESHOOTING Problem Possible cause s Suggested remedy No power to the fixture Check connections If power is applied and the Blown fuse lamp is switched on but does not light check and replace fuse if necessary No light Burned out lamp Install new lamp Fixture too hot Allow to cool Improve air flow around fixture No action in music trig mode Sound too low to activate control circuit Adjust music level sensitivity Increase music volume Reduce distance between fixture and loudspeakers No action in music trig and auto trig modes Electrical malfunction Refer to a Martin service technician Unsatisfactory action in synchronized operation Fixtures incorrectly linked Check data link connections between fixtures More than one fixture set as master Check that all slave fixtures are set to DMX mode Poor action in a new fixture Some transport packaging has not been removed Remove all plastic ties from mirror drum until drum rotates freely Fuse blows repeatedly Electrical malfunction Refer to a Martin service technician EFX600 Impossible to restrike lamp after dousing via DMX 8 minute restrike protection delay activated Wait 8 minutes before restriking a hot lamp Fixtures reset correctly but behave erratica2. User manual EFX500 250 watt halogen lamp installed EFX600 150 watt discharge lamp the EFX600 discharge lamp is supplied separately to avoid damage during shipping and must be installed before use see Installing the EFX600 lamp on page 25 Removing protective packaging The mirror drum is secured with packaging and white plastic ties for shipment Wearing gloves to avoid cutting yourself on the mirrors cut and remove the plastic ties Check that the drum can be swivelled through 180 and rotated through 360 before operating the fixture If it cannot you may have missed one of the plastic ties Remove the clear protective film from the mirror drum before operating Introduction 7 INSTALLATION Warning Important Warning AC power Ensure that the fixture s voltage setting matches your local AC power supply before applying power For protection from fire and electric shock the fixture must be grounded earthed The power supply must have both overload and ground fault earth fault protection Check that power cables are undamaged and rated for the current requirements of all connected devices before use Do not connect the fixture to a dimmer system as this may cause damage that is not covered by the product guarantee Mania EFX500 power settings All Mania EFX500 models must be set to 115 V 60 Hz or 230 V 50 Hz AC power using the red voltage selector switch on th
3. 98 100 Mirror dish music trig dynamic Pan mirror drum swivel position shake and music trig 0 0 Maximum left pan 63 24 Neutral 5 127 50 Maximum right pan 128 182 51 71 Narrow shake slow fast 183 239 72 93 Wide shake slow fast 240 244 94 95 Music trig pan fast 245 249 96 97 Music trig pan slow 250 255 98 100 Music trig pan dynamic Tilt mirror drum rotation rotation shake and music trig 0 1 0 No rotation 2 63 1 24 Clockwise rotation slow fast 64 65 25 No rotation 6 66 127 26 49 Counterclockwise rotation fast gt slow 128 129 50 No rotation 130 184 51 72 Narrow shake slow fast 185 239 73 93 Wide shake slow fast 240 244 94 95 Mirror drum rotation music trig fast 245 249 96 97 Mirror drum rotation music trig slow 250 255 98 100 Mirror drum rotation music trig dynamic Macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 1 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 7 96 111 38 43 Macro6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 12 208 255 82 100 Reserved No function Effects speed DMX mode 2 only 8 0 1 0 Tracking default 2 255 1 100 Fast gt slow Channels 7 and 8 are available in DMX mode 2 only In DMX mode 1 effects speed
4. is set to tracking MANIA EFX500 600 SPECIFICATIONS Physical Size with mounting plate LxWXH 410 x 500 x 230mm 16 2 x 19 7 x 9 1 in Mania EFX500 weight with mounting plate 12 5 kg 27 6 Ib Mania EFX600 EU model weight with mounting plate 14 kg 31 Ib Mania EFX600 US model weight with mounting plate 16 5 kg 36 5 Ib Installation Orientation cene teca aided Minimum distance tocombustiblematerial 0 1 m 4 in Minimum distance to illuminated surface 0 3 m 12 in Minimum clearance around air vents Suitable for mounting on combustible surfaces wood etc using mounting bracket and plate and respecting specified minimum distances Construction HOUSING iex bee steel and aluminum rubber corner protectors Source Mania EFX500 24 V 250 W halogen lamp with integral reflector Mania EFX500 lamp socket Mania EFX600 ex za EHE ER 150 W discharge lamp Mania EFX600 lamp socket Control and programming DMX control USITT DMX 512 1990 DMX protocol Mania EFX500 number of DMX channels 7 mode 1 or 9 mode 2 Mania EFX600 number of DMX channels 6 mode 1 or 8 mode 2 Data I O connections 3 pin locking XLR pin 1 shield
5. a surface by means of its mounting plate and suitable bolts Do not install the fixture by any other means as this can cause the fixture to overheat Ensure that the mounting structure or surface and all fasteners used can support at least 10 times the weight of all installed fixtures clamps cables auxiliary equipment etc Ensure that the fixture is located atleast 1 meter 3 3 ft away from the surface to be illuminated atleast 0 1 meters 4 in from any combustible materials wood fabric paper etc and well away from any flammable materials Ensure that the clearance around the fan and air vents is at least O 1 meters 4 in and that airflow is free and unobstructed Block access below the work area and work from a stable platform when installing or servicing the fixture Always use a secure means of secondary attachment that can hold at least 10 times the weight of the fixture looping it through the attachment point shown at F in Overview on page 4 Do not simply pass the secondary attachment around the mounting plate as this will leave the fixture unsecured Installation 9 10 Surface mounting lt To mount the Mania EFX500 600 surface you will need four grade 8 8 minimum 8mm diameter 13mm head hex screwbolts or similar type fasteners of the same grade and size and an eyebolt for the safety cable 7 Installing the mounting plate separately Surface mounting is easiest if
6. light shows on two or more fixtures master slave operation Installation 11 Fixtures on a serial data link must be daisy chained in one single line maximum 500 meters 1640 ft long with maximum 32 fixtures If you wish to exceed 32 fixtures or 500 meters or to split the link into branches use an optically isolated amplifier splitter such as the Martin RS 485 Opto Splitter P N 90758060 Reliable data connection requires suitable cable Standard microphone cable cannot transmit DMX data reliably over long runs For best results use cable with at least one twisted pair specifically designed for RS 485 applications Your Martin dealer can supply suitable high quality cable in various lengths Connecting the serial data link The Mania EFX s data connections are XLR type wired with pin 1 to ground pin 2 to signal cold and pin 3 to signal hot This is the standard configuration for DMX devices One or more adaptor cables may be required to connect the Mania EFX to the controller and or other types of fixture because some devices may have 5 pin XLR connectors and others may have reversed signal polarity pin 2 hot and pin 3 cold Connector polarity is normally specified on the device or in the device s user manual 5 pin to 3 pin 3 pin to 5 pin 3 pin to 3 pin Male Female DMX Adaptor Adaptor Phase Reversing Termination Plug Termination Plug Adaptor Male Female Male Female Mal
7. set to DMX mode Mania EFX500 amp EFX600 user manual Important DMX mode In DMX mode fixtures receive control instructions via the serial data link They will respond to control signals from a DMX controller or from another fixture set as master Selecting DMX music trig or auto trig operating modes The Mania EFX is supplied set to DMX mode with DMX address set to 1 If you intend to operate the fixture without a DMX controller you need to set the fixture to music trig or auto trig mode To switch between DMX auto trig and music trig modes 1 Apply power to the fixture and wait while it resets If the fixture is in DMX mode the display will show the O fixture s DMX address 2 Press the Mode button once The fixture enters auto trig mode and 900 DMX Address appears in the display 3 Press the Mode button again once The fixture enters music trig mode X100 x10 P dnm and 90 appears in the display 4 Press the Mode button again once to Mode button return to DMX mode The fixture s DMX address appears in the display The fixture will return to the mode you have set when it is powered off and on If you set the fixture to music trig mode but it does not respond satisfactorily to the music beat adjust the music trig sensitivity level see Adjusting music trig sensitivity on page 20 Synchronized music trig and auto trig operation You can set multiple fixtures on a seri
8. starting it in hard boot mode To start in hard boot mode hold both the Mode button and the X100 button pressed in while powering on the fixture When the Mania EFX is in hard boot mode the data LED blinks If you are not sure how to carry out uploads your Martin dealer will be able to give advice or carry out the upload for you Service and maintenance 27 MANIA EFX500 CIRCUIT BOARD LAYOUT Voltage Main PCB Selecter J12 Switch Lamp Power Main PCB PCB Transformer J7 J1 Fan Transformer Display DMX Main PCB Power PCB J9 Power PCB J6 Hall Color J6 Gobo Tilt Pan Mirror Color Gobo Dish 28 Mania EFX500 amp EFX600 user manual MANIA EFX600 CIRCUIT BOARD LAYOUT Transformer 15 Main PCB J5 Main PCB J12 J12 Main PCB Mania EFX600 Main PCB 313 US J2 13 Power PCB Fan Ballast Capacitor t Fuse t Toroidal transformer 250V Display Ballast J5 Mania EFX600 EU Power PCB J2 Mains filter t 7 Toroidal transformer Hall Color Gobo Mania EFX600 EU US Main PCB Power PCB DMX Power PCB J9
9. the beam is centered in the projected images ow adjustment 99 Lamp adjustment Lamp adjustment Replacing the main fuse The Mania EFX500 600 uses a slow blow fuse for protection against current overload An indication that the fuse may have blown is that when power is applied and the lamp is switched on no light is produced If the fuse blows repeatedly there is probably a fault Disconnect the fixture from power and data and contact a Martin service technician Never bypass the fuse or replace it with one of another type or rating To replace the main fuse 1 Disconnect the power cable 2 Pry open the fuse holder next to the power cable inlet with a flat head screwdriver and remove the fuse 3 Replace the fuse with one of the same type and rating Fuse ratings are listed on serial number labels and under Electrical on page 37 4 Replace the fuse holder before reapplying power Cm Firmware and hard boot uploads It is possible to upload new firmware to the Mania EFX via the data IN connector using for example an uploader such as the Martin MP 2 Uploader or a PC using a Martin DABS interface device and suitable software The latest version of the Mania EFX firmware is available in the Support area of the Martin website at http www martin com Mania EFX500 amp EFX600 user manual If the Mania EFX will not accept normal firmware uploads it can be forced to accept an upload by
10. 0 50 2 204 W 1 0 A PF 0 923 Mania EFX600 US model CERTUM MEI pc 3 prong IEC male socket AC SORE tee nk Cete p reducat uet 115 120 V 60 Hz Main TUS A e e YE 3 15 AT Typical power and current HOV 60 HZ ms 189 W 1 8 A PF 0 963 115 V 60HZ _ aa er aaa quq ag 207 W 1 9 A PF 0 964 120 V 60 HZ 226 W 2 0 A PF 0 957 V volts Hz hertz W watts A amps PF power factor Allow for a deviation of 10 from typical figures listed above Measurements made at nominal voltage Local supply voltages can vary by 10 Thermal EFX500 maximum exterior surface temperature steady state 100 C 212 F EFX600 maximum exterior surface temperature steady state 80 C 176 F Time required to cool before handling minimum 10 minutes Maximum ambient temperature Ta 40 C 104 F Approvals C c 1sTEV m ente EN 55015 EN 61547 EN 61000 3 3 EN 61000 3 2 EU Safety oce Gag e EN 60598 1 EN 60598 2 17 US SATS ke cs ce sate carers ie azl ame eee ten A a Raqay UL 1573 Canadian safety CSA C22 2 NO 166 Included items EFX500 all models Long life 250 W halogen lamp 3 m 9 8 ft EU mains cable 3x1 Omm with Schuko male connector 3 m 9 8 ft EU mains cable 3x1 wi
11. 39 87 94 Blackout shutter closed 240 249 95 98 Reset fixture value must be held for 5 seconds 250 255 99 100 Lamp off value must be held for 5 seconds and channels 2 amp 3 must be set to more than 252 99 Note that there is a five minute delay before lamp can be restruck Colored gobo wheel position rotation and music trig Full gobo positions 0 9 0 3 Gobo 1 10 19 4 7 Gobo2 20 29 8 11 Gobo 3 30 39 12 15 Gobo 4 40 49 16 19 Gobo 5 50 59 20 23 Gobo 6 60 69 24 26 Gobo 7 70 79 27 30 Gobo 8 80 89 31 35 Gobo 9 2 90 99 36 38 Gobo 10 100 109 39 42 Gobo 11 110 119 43 46 Gobo 12 120 175 47 68 Reserved gobo 12 Continuous Rotation 176 207 69 81 Clockwise fast slow 208 239 82 93 Counterclockwise slow fast Music function 240 244 94 95 Gobo wheel music trig fast 245 249 96 97 Gobo wheel music trig slow 250 255 98 100 Gobo wheel music trig dynamic Colored gobo wheel shake 3 0 1 0 No function 2 128 1 50 Narrow shake slow fast 129 255 51 100 Wide shake slow fast Channel Value Percent Function Mirror dish rotation shake and music trig 0 1 0 Stop 2 65 1 25 Counterclockwise rotation fast slow 66 129 26 50 Clockwise rotation slow fast 130 192 51 75 Shake various shakes 4 193 208 76 81 Random shake 209 239 82 93 Reserved stop 240 244 94 95 Mirror dish music trig fast 245 249 96 97 Mirror dish music trig slow 250 255
12. Disconnect the fixture from power and allow it to cool for at least 10 minutes 2 Loosen the screw holding the lamp cover see illustration on right and open the cover The cover is attached to the housing with a safety strap 3 Loosen the four small screws see illustration on right holding the lampholder and pull the lampholder gently out of the fixture Note which edge faces outwards as the lampholder must be reinstalled in the same position This edge faces out 4 If replacing an old lamp remove it from its ceramic socket 5 Hold the new lamp by its base do not touch any other part of the lamp Push the lamp pins squarely into the socket 6 If you touched the bulb the reflector or any optical components clean them with a clean soft lint free cloth wetted with isopropyl alcohol and dry with a clean soft lint free cloth or compressed air 7 Replace the lampholder in the housing making sure that the edge with the semicircular cutout in its center faces out towards the edge of the and reinstall the four screws Close the lamp cover checking that no wires are trapped and replace the lamp cover screw 8 Reapply power Service and maintenance 25 26 EFX600 lamp adjustment The EFX600 lamp alignment can be adjusted to optimize the projected image using the adjustment screws on the lampholder see illustration on right Experiment with turning the screws until the brightest part of
13. EFX600 user manual from one scene to the next If you select tracking the DMX controller defines fade times Unsure about speed and tracking Set the fixture to tracking if you are using programmed fade times or macros on your DMX controller Select an effects speed if you are not using programmed fade times or macros on your DMX controller However if you are using fade times on your controller and have set the fixture to tracking but effects movement is rough and irregular setting fade times on your controller to zero and selecting an effects speed may give smoother movement Effects movement is set to tracking if the fixture is in DMX mode 1 and by default DMX signal indicator When the Mania EFX receives a valid DMX DMX signal received signal the green Data LED will light to show that the fixture is receiving control data DMX Address Data LED lit Fixture control menu You can change various personality settings by holding the Mode button pressed in for 5 seconds and then using the buttons on the control panel Changing the DMX mode is described in Setting DMX mode 1 or 2 on page 16 Inverting pan and tilt for symmetrical action You can create symmetrical action across multiple fixtures in synchronized and DMX operation by inverting pan and or tilt on some fixtures so that they mirror the action of others When one fixture pans left for example a fixture on the other si
14. Mania EFX500 EFX600 user manual Martin DIMENSIONS Measurements are expressed in millimeters p 500 180 x 5 NSZ EN pum 7 YU k X 4 f N 2005 2006 Martin Professional A S Denmark All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Professional A S Denmark P N 35000168 Rev E CONTENTS OVENVIEW ak e x S Race cutus PCR RA pra ete 4 Introduction 5 Safety information 5 Unpacklng RES eU RE et a ETE eM 7 Installation 8 AG POWO ss uen 8 Physical installation 9 Creating a data link for DMX and synchronized operation 11 Gobo wheels 13 Operation es gla sozle Pid 14 Getting started 14 Music trig auto trig and DMX modes 14 Synchronized music trig and auto trig operation 15 DMX controller operation 16 Fixturecontrolmenu 19 Error messages serer dalin UR 21 Striking the EFX600 lamp 21 Adjusting fOCus iius tesa iy
15. al data link to respond together to a music trig or auto trig signal from one fixture This feature allows synchronized operation without a DMX controller The fixture sending the signal is the master fixture and the fixtures that receive the signal are the slave fixtures Set only one fixture as master damage can occur if two masters or a master and a DMX controller are linked Operation 15 16 Setting up synchronized operation To set up Mania EFX fixtures for synchronized operation 1 Ensure that all fixtures on the data link are in DMX mode 2 Select one fixture to be the master and set it to auto trig or music trig mode see Selecting DMX music trig or auto trig operating modes on page 15 3 When a slave fixture receives signals from the master it will automatically begin operating in slave mode 9 ID will appear in its display and the green Data LED will light to show that the fixture is receiving control data Slave mode DMX Address Data LED lit X100 X10 pes Mode button Fixtures return to their DMX auto trig music trig settings when powered off and on so you should only need to set fixtures as masters slaves once DMX controller operation Setting DMX mode 1 or 2 Two DMX modes are available DMX mode 1 normal and DMX mode 2 extended Mode 2 uses two extra DMX channels that allow you to select pre programmed macros and set the speed of effects movement from the DMX controller Th
16. covers as described in Cleaning the fan and air vents above Blow or vacuum away loose dust Remove dirt from lenses gobos and mirror wheel with a soft cloth or cotton swabs Optical path wetted with isopropyl alcohol Regular glass cleaner may also be used but no residues may remain To avoid scratches do not rub Instead press repeatedly to lift dirt off surfaces Any remaining residues or streaking can be removed with distilled water Mixing the water with a small amount of wetting agent such as Kodak Photoflo will help prevent streaking and spotting Dry with a clean soft lint free cloth or compressed air Reinstall all covers before reapplying power Lamp replacement and adjustment Wear safety glasses and gloves and allow the fixture to cool for at least 10 minutes before replacing lamps Mania EFX500 lamp The Mania EFX500 uses a 250 W halogen lamp Replace the lamp when it reaches the average life specified by the manufacturer Service and maintenance 23 Important Use only this type of lamp See Accessories on page 38 for 24 details of replacement lamps Installing any other lamp may damage the fixture Replacing the EFX500 lamp 1 Disconnect the fixture from power and allow it to cool for at least 10 minutes 2 Loosen the lamp cover release thumbscrew enough to slide and lift the lamp cover out of the fixture housing The lamp cover is attached to the housing
17. de of the dance floor can bet set to pan right Operation 19 20 Inverting pan To invert pan mirror drum swivel on a Mania EFX 1 2 Power the fixture on Hold the Mode button pressed in for 5 seconds to enter the control menu Press the X100 button repeatedly until appears on the left of the display Press the X1 button to change the pan DMX Address setting on the right of the display from 0 e oe O normal pan to inverted pan X100 X10 X1 Mode Press the Mode button again to save your setting and exit the control menu Inverting tilt To invert tilt mirror drum rotation on a Mania EFX 1 2 Power the fixture on Hold the Mode button pressed in for 5 seconds to enter the control menu S Press the X100 button repeatedly until 8 appears on the left of the display Press the X1 button to change the tilt DMX Address setting on the right of the display from D e normal tilt to inverted tilt X100 X10 1 Mode Press the Mode button again to save your setting and exit the control menu Adjusting music trig sensitivity To adjust sensitivity for optimum synchronization with the music 1 Press the X1 button to select a music With the fixture powered on and in music trig mode play a typical music track at O typical volume for your location Q Hold the Mode button pressed in for 5 seconds to enter
18. e Female Male XLR Female XLR 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 d 3 d s ec 31120 Ohm 3 120 Ohm 4 4 5 5 P N 11820005 P N 11820004 P N 11820006 P N 91613017 P N 91613018 12 DMX connectors and polarity To connect the data link 1 Power all devices off 2 If you intend to use a DMX controller run a data cable from the DMX controller s data output to the first fixture s data IN socket If the controller has a 5 pin output use a 5 pin male to 3 pin female adaptor cable P N 11820005 3 If you intend to run fixtures in master slave operation insert a female DMX termination plug P N 91613018 in the first fixture s data IN socket Mania EFX500 amp EFX600 user manual 4 Plug a data cable into the OUT socket of the first fixture and the IN socket of the next one Continue connecting up to 32 Mania EFXs output to input 5 Terminate the link by inserting a male termination plug P N 91613017 into the data output of the last fixture A termination plug is simply an XLR connector with a 120 Ohm 0 25 W resistor soldered across pins 2 and 3 Gobo wheels The Mania EFX500 contains the following gobo wheel K ES Note that it is the whole wheel and not the individual gobos that rotates Rotating gobo image effects are created by the mirror dish Installation 13 OPERATION 14 Getting started The Mania EFX500 600 is supplied in DMX mode with its DMX address set to 1 If y
19. e connections panel Set the switch so that 115 V is visible if you have110 120 V 60 Hz AC power Set the switch so that 230 V is visible if you have 220 240 V 50 Hz AC power Mania EFX600 power settings Mania EFX600 EU models must be set to 230 or 240 V 50 Hz AC power using the voltage selector switch on the connections panel Mania EFX600 US models do not have a voltage selector switch and are supplied set up for 110 120 V 60 Hz AC power Do not operate the fixture on a power supply that falls outside of these ranges Installing a cord cap plug on the power cable The fixture s power cable may require a grounding type cord cap earthed mains plug that matches your power distribution system Consult a qualified electrician if you have any doubts about proper installation Mania EFX500 amp EFX600 user manual Warning Following the cord cap manufacturer s instructions connect the appropriate wires to ground earth live and neutral The table below shows some common wire identification schemes Function Wire EU Wire US Marking Screw color live brown black L yellow or brass neutral blue white N silver ground yellow green green ae green Table 1 Cord cap wiring Physical installation The Mania EFX500 600 must be either fastened to an overhead structure by means of its mounting plate and a Martin rigging clamp available from your Martin dealer or fastened to
20. e fixture is supplied set to DMX mode 2 The Mania EFX500 uses seven DMX channels in DMX mode 1 and nine channels in DMX mode 2 The Mania EFX600 uses six DMX channels in DMX mode 1 and eight channels in DMX mode 2 Mania EFX500 amp EFX600 user manual To toggle between DMX modes 1 and 2 1 Apply power to the fixture and wait for the fixture to reset 2 Hold the Mode button pressed in for 5 seconds to enter the fixture control DMX Address ids eee 3 Press the X100 button repeatedly until appears in the left of the display Press the X1 button to toggle between DMX mode 2 to set DMX mode 1 and to set DMX mode 2 in the right of the display 4 Press the Mode button again to save your setting X100 x10 X1 Mode Setting DMX addresses If you intend to use a DMX controller you will need to set the DMX address for each fixture The DMX address also known as the start channel is the first channel used to receive instructions from the controller It is set using the three addressing buttons on the Mania EFX s control panel For individual control each fixture must be assigned its own DMX address and control channels Control channels must not overlap with those of other fixtures Fixtures of the same type with the same DMX address will receive the same instructions and behave identically If a Mania EFX500 is set to DMX mode 2 it will use 9 channels If you give it DMX address 100 for exam
21. e sek EVE en y E 21 Service and maintenance 22 Cleaning use exam eR ERE ey ee ee le 22 Lamp replacement and adjustment 23 Replacingthemainfuse 26 Firmware and hard boot uploads 27 Mania EFX500 circuit board layout 28 Mania EFX600 circuit board layout 29 Troubleshooting 30 Control menu 31 Mania EFX500 DMX protocol 32 Mania EFX600 DMX protocol 34 Mania EFX500 600 specifications 36 OVERVIEW Power inlet Voltage selector switch EFX500 all models amp EFX600 EU models DMX in DMX out Display and control buttons Safety cable attachment point Power on off switch A B 4 Mania EFX500 amp EFX600 user manual INTRODUCTION Warning Thank you for selecting a Martin Mania EFX series dynamic lighting fixture The Mania EFX500 and EFX600 are DJ lighting effects with a motorized rotating parabolic mirror dish a motorized rotating gobo wheel gobos are outlines or masks placed in a light beam to create different patterns and a mirror drum with motorized pan swivel and tilt rotation The Mania EFX500 and EFX600 offer the following features Stand alone single fixture and synchronized master slave o
22. ere to a qualified technician Disconnect the fixture from power and allow it to cool for at least 10 minutes before removing any cover Cleaning Excessive dust grease and smoke fluid buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty Check and if necessary clean fixtures at regular intervals Cleaning the fan and air vents To maintain adequate cooling dust must be cleaned from the fan and air vents periodically 1 Disconnect the fixture from power and allow it to cool for at least 10 minutes 2 Loosen the lamp cover release thumbscrew and slide and lift the lamp cover out of the fixture housing Let the cover hang on its safety strap 3 Remove the four torx screws holding the main cover see illustration on right and slide and lift the cover out of the housing Let the cover hang on its safety strap 4 Remove dust and dirt from the fan blades and vent grills using a soft brush cotton swab vacuum or compressed air 5 Reinstall the main cover and lamp cover securely before reapplying power Mania EFX500 amp EFX600 user manual Warning Cleaning optical components Use care when cleaning optical components The coated surfaces are fragile and even small scratches may be visible in the fixture s light output 1 Disconnect the fixture from power and allow it to cool for at least 10 minutes Open the
23. lly or do not respond during DMX or synchronized operation Data link not terminated Insert DMX termination plug in output of last fixture on link In synchronized operation insert DMX termination plug in input of first fixture Mania EFX500 amp EFX600 user manual CONTROL MENU Hold the Mode button pressed in for 5 seconds to access the control menu Use the X100 button to select the personality feature Use the X1 button to change the setting for that feature O Q Personality feature DMX Address Setting X100 X10 X1 Mode Personality feature Setting Mode 1 normal 0 DMX mode Mode 2 extended ru Pan normal l Pan swivel invert l Pan inverted D Tilt normal Tilt rotation invert l Tilt inverted Minimum 3 Music trig sensitivity lo e Maximum Default settings are shown in bold type MANIA EFX500 DMX PROTOCOL Channel Value Percent Function Strobe effect auto trig music trig reset 0 4 0 1 No function 5 68 2 26 Strobe fast to slow 1 69 100 27 39 Remote stand alone auto trig 101 132 40 51 Remote stand alone music trig 133 249 52 97 Reserved no function 250 255 98 100 Reset fixture value must be held for 5 seconds 2 Intensity 0 255 0 100 0 100 Colored gobo wheel positions gobo wheel rotation gobo wheel music trig Full gobo positions 0 9 0 3 Gobo 1 10 19 4 7 Gob
24. o2 20 29 8 11 Gobo3 30 39 12 15 Gobo4 40 49 16 19 Gobo5 50 59 20 23 Gobo6 60 69 24 26 Gobo7 70 79 27 30 Gobo8 3 80 89 31 35 Gobo9 90 99 36 38 Gobo 10 100 109 39 42 Gobo 11 110 119 43 46 12 blackout 120 175 47 68 Reserved Gobo 12 blackout Continuous Rotation 176 207 69 81 Clockwise fast slow 208 239 82 93 Counterclockwise slow fast Music function 240 244 94 95 Gobo wheel music trig fast 245 249 96 97 Gobo wheel music trig slow 250 255 98 100 Gobo wheel music trig dynamic Colored gobo wheel shake 4 0 1 0 No function 2 128 1 50 Narrow shake slow fast 129 255 51 100 Wide shake slow fast Mirror dish rotation shake and music trig 0 1 0 Stop 2 65 1 25 Counterclockwise rotation fast slow 66 129 26 50 Clockwise rotation slow fast 130 192 51 75 Shake slow fast 5 193 208 76 81 Random shake 209 239 82 93 Reserved stop 240 244 94 95 Mirror dish music trig fast 245 249 96 97 Mirror dish music trig slow 250 255 98 100 Mirror dish music trig dynamic Channel Value Percent Function Pan mirror drum swivel position shake and music trig 0 0 Maximum left pan 63 24 Neutral 6 127 50 Maximum right pan 128 182 51 71 Narrow shake slow fast 183 239 72 93 Wide shake slow fast 240 244 94 95 Music trig pan fast 245 249 96 97 Music trig pan slow 250 255 98 100 Music trig pan dynamic Tilt mirr
25. ole to accept a screwbolt that will lock the fixture in place 6 Remove the fixture from the surface drill the fourth hole and replace the fixture on the surface as described in point 4 above Screw the fourth screwbolt through the mounting plate into the surface to lock the fixture in place using a washer on the screwbolt if necessary 7 Install an eyebolt and safety attachment once the fixture is mounted Overhead mounting To hang the Mania EFX on an overhead structure 1 If using a rigging clamp ensure that the clamp is undamaged and can bear at least 10 times the fixture s weight Bolt the clamp securely to the fixture s mounting plate with a grade 8 8 minimum M12 bolt and lock nut through one of the 13 mm holes provided or as recommended by the clamp manufacturer The clamp must be attached centrally in the mounting plate to distribute the load evenly 2 Working from a stable platform clamp or fasten the fixture to the structure 3 Install a safety cable that can hold at least 10 times the weight of the fixture 4 Loosen the swivel locks tilt the fixture to the desired angle and retighten Check to make sure that the mirror drum cable does not rub on the mounting plate If it does reverse the mounting plate see illustration Creating a data link for DMX and synchronized operation You need a serial data link to run light shows on one or more fixtures using a DMX controller or run synchronized
26. or drum rotation rotation shake and music trig 0 1 0 No rotation 2 63 1 24 Clockwise rotation slow fast 64 65 25 No rotation 7 66 127 26 49 Counterclockwise rotation fast slow 128 129 50 No rotation 130 184 51 72 Narrow shake slow fast 185 239 73 93 Wide shake slow fast 240 244 94 95 Mirror drum rotation music trig fast 245 249 96 97 Mirror drum rotation music trig slow 250 255 98 100 Mirror drum rotation music trig dynamic Macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 8 96 111 38 43 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function Effects speed DMX mode 2 only 9 0 1 0 Tracking default 2 255 1 100 Fast slow Channels 8 and 9 are available in DMX mode 2 only In DMX mode 1 effects speed is set to tracking MANIA EFX600 DMX PROTOCOL Channel Value Percent Function Intensity strobe effect auto trig reset lamp off 0 4 0 1 Blackout shutter closed 5 122 2 47 Intensity 0 100 lamp on 123 129 48 50 Shutter open 130 189 51 74 Strobe fast to slow 190 199 75 78 Shutter closed 1 200 209 79 82 Random strobe 210 219 83 86 Remote stand alone auto trig 220 2
27. ou want to operate the fixture without a DMX controller you need to set the fixture to music trig or auto trig mode before use see Selecting DMX music trig or auto trig operating modes on page 15 Powering on Once the fixture is correctly and safely installed power on at the fixture s power on off switch The fixture will start up and reset If the fixture resets successfully the software version installed will appear in the display For example if software version 1 00 is installed the message 100 should appear in the display Once the fixture has reset the fixture will display either its DMX address 90 1 music trig mode or 909 auto trig mode If any other message is displayed the fixture has detected an error see Error messages on page 21 If this occurs switch off wait a few seconds and switch on again If the error message appears again consult your Martin dealer Music trig auto trig and DMX modes The Mania EFX has three main operating modes Music trig mode In this mode lighting effects are triggered by music intensity Multiple fixtures can be synchronized if one master fixture is set to music trig mode and the other fixtures are set to DMX mode Auto trig mode In this mode the fixture runs a factory set dynamic light show that uses all the fixture s effects in a random program Multiple fixtures can be synchronized if one master fixture is set to auto trig mode and the other fixtures are
28. peration in auto and music triggering modes DMX control Two DMX modes DMX mode 2 gives extended functionality on additional channels 180 pan and 360 tilt Adjustable focus Adjustable music triggering sensitivity The EFX500 has 11 colored gobos plus blackout and the EFX600 has 12 colored gobos The Mania EFX500 is supplied with a long life 250 watt halogen lamp The Mania EFX600 is supplied with a long life 150 watt discharge lamp Safety information This product is not for household use It presents risks of lethal or severe injury due to fire and heat electric shock ultraviolet radiation lamp explosion and falls This product presents risks of lethal or severe injury due to fire and heat electric shock ultraviolet radiation lamp explosion and falls Read this manual before installing or powering the fixture follow the safety precautions listed below and observe all warnings in this manual and on the fixture If you have any questions about how to operate the fixture safely please contact your Martin dealer or call the Martin 24 hour service hotline Introduction 5 Warning Protecting yourself and others from electric shock and injury Ensure that the fixture s voltage setting matches your local AC power supply before applying power Disconnect the fixture from AC power before removing or installing the lamp fuse or any part and when not in use Always ground earth the fixture elect
29. pin 2 pin 3 Stand alone music trig single fixture and synchronized master slave Stand alone auto trig single fixture and synchronized master slave Individual effects can be set to music trig remotely via DMX Dynamic effects Motorized rotating parabolic mirror dish Motorized rotating gobo wheel 11 colored gobos plus blackout EFX500 12 colored gobos EFX600 Motorized rotating amp swivelling mirror drum a ll Reaction salan Sites ah yeaa I a uw suya Haare aaa Electrical Mania EFX500 all models jor p 3 prong IEC male socket AC power Switch selectable 110 120 V 60 Hz 220 240 V 50 Hz Mail fuse scudo kn ed le ek Oe BN eae aede dos 3 15 AT Typical power and current 110 V 60 Hz mile veda Reli 229 W 2 1 A PF 0 997 115 V 60 HZ Res 248 W 2 2 A PF 0 997 120 V 60 HZ i n ier 264 W 2 2 A PF 0 997 220 V 50 Hz eoi REM 229 W 1 1 A PF 0 995 0 230 V 50 HZ ceni de daha a Re be 247 W 1 1 A PF 0 995 240 V 50 Hz ees era ei ek dee cane 265 W 1 2 A PF 0 994 Mania EFX600 EU model If put chew ted kee See as 3 prong IEC male socket AC D NEN eem membr dee deni Switch selectable 230 V 240 V 50 Hz Main fuse io e pee dum p dd Ra dece ea Rc didus 2AT Typical power and current 220 V 50 HZ iiec tems lan lena 181 W 0 9 A PF 0 950 0 230 V 50 AZ iere mb Ca E 197 W 1 0 A PF 0 926 24
30. ple it will use channels 100 101 102 103 104 105 106 107 and 108 Channel 109 is available for the next fixture The default factory set DMX address is 1 To set a fixture s DMX address OO 1 Decide on suitable DMX addresses for all the fixtures on the data link 512 channels are available in one DMX universe 2 Appl to the fixt d wait while it DMX Address Apply power to the fixture and wait while i resets e 3 Use the three addressing buttons on the 100 X10 1 fixture s control panel to enter the DMX DMX addressing address The X1 button increases the buttons last digit in the DMX address the X10 button increases the address by 10 and the X100 button increases the address by 100 Fixtures remember their DMX address when they are powered off and on Operation 17 18 DMX control options See also the DMX protocols starting on page 32 for an overview of DMX commands and channels In DMX modes 1 and 2 the following functions can be controlled Strobe effect A strobe effect with variable flash rate can be selected Auto trig While in DMX mode the Mania EFX can be remotely set to auto trig Reset All effects can be reset to their index positions from the controller using channel 1 The reset command must be sent for 5 seconds before it takes effect When a fixture is reset via DMX 820 should appear in the digital display Dimming The Mania EFX500 can be dimmed from 0 blacko
31. r 16 4 ft RS 485 XLRcablefordatalink P N 11820008 Mania EFX500 all models main fuse 3 15 P N 05020043 Mania EFX600 EU models main fuse 2 P N 05020009 Mania EFX600 US models main fuse 3 15 P N 05020043 Ordering information Mania EFX500 115 230 V 50 60 HZ P N 90430050 Mania EFX600 EU model 220 240 V 50 HZ P N 90430052 Mania EFX600 US model 110 120 V 60 HZ P N 90430053 OC E gt gv Mart n www martin com e Olof Palmes All 18 e 8200 Aarhus N Denmark Tel 45 8740 0000 e Fax 45 8740 0010
32. rically Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose the fixture to rain or moisture Refer all service not described in this manual to a Martin service technician Do not operate the fixture if any covers or components are missing damaged or deformed Do not use the product if the power cable is damaged Replace the cable with a Martin item only available from your Martin dealer Protecting yourself and others from burns and fire Hot lamp The exterior of the fixture can become hot Allow to cool for at least 10 minutes before handling or opening Surface temperature under steady state condition 100 C 212 F Do not operate the fixture if the ambient temperature T4 exceeds 40 C 104 F Never attempt to bypass the thermostatic switch or fuses Always replace defective fuses with ones of the specified type and rating See serial label for replacement fuse size and lamp type Keep all combustible materials for example fabric wood paper at least 0 3 meters 4 inches away from the fixture Keep flammable materials well away from the fixture Do not illuminate surfaces within 1 meter 3 3 feet of the fixture Provide a minimum clearance of 0 1 meters 4 inches around fans and air vents and ensure that air flow through and around vents is free and unobstructed Never place filter
33. s or other materials over the lens or in the optical path Do not look directly into the light Change the lamp immediately if it becomes damaged or thermally deformed Do not operate the fixture if any optical components or shields are missing damaged or deformed an unshielded discharge lamp emits dangerous UV radiation that can cause burns and eye damage Do not modify the fixture or install other than genuine Martin parts Mania EFX500 amp EFX600 user manual Important Important Preventing injuries due to falls When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Ensure that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Block access below the work area and work from a stable platform whenever installing or removing the fixture Unpacking Do not lift or carry the fixture by holding the plastic mirror drum motor housing It is not designed for this purpose You could injure yourself or others and you could cause damage that is not covered by the product guarantee The packing material is carefully designed to protect the fixture during shipment always use it to transport the fixture Mania EFX fixtures are supplied with the following items 3 wire IEC power cable 5m 16 4 ft DMX cable Mounting plate installed
34. th no male connector 2 m 6 5 ft US mains cable 18AWG with US male connector UL approved 5 meter 16 4 ft RS 485 XLRcablefordatalink P N 11820008 User manual 5 eee een teo en ai CR aa P N 35000168 Included items EFX600 EU 230 V models Long life 150 W discharge lamp 3 m 9 8 ft EU mains cable 3x1 Omm with Schuko male connector 3 m 9 8 ft EU mains cable 3x1 Omm with no male connector 5 meter 16 4 ft RS 485 XLRcablefordatalink P N 11820008 User manual 5 u bcr e Ree reper REN P N 35000168 Included items EFX600 US 115 V models Long life 150 W discharge lamp 2 m 6 5 ft US mains cable 18AWG with US male connector UL approved 5 meter 16 4 ft RS 485 XLRcablefordatalink P N 11820008 User manual AGER yi kirk P N 35000168 Accessories Philips ELC 10H 250 W halogen lamp EFX500 P N 97000109 Philips CDM SA T 150 W discharge lamp EFX600 P N 97010111 Osram HSD 150 70 150 W discharge lamp EFX600 P N 97010117 DMX termination plug end of link XLR male P N 91613017 DMX termination plug start of link master slave XLR female P N 91613018 bend a i a upa ayah a e uox s P N 91602003 Half coupler clamp P N 91602005 5 pin male to 3 pin female XLR adaptor cable P N 11820005 5 mete
35. the control menu DMX Address Press the X100 button repeatedly until 3 appears on the left of the display X100 X10 X1 Mode trig sensitivity setting on the right of the display from I minimum sensitivity to 9 maximum sensitivity The default setting is 6 Press the Mode button again to save your setting and exit the control menu Mania EFX500 amp EFX600 user manual Error messages In the event of a gobo wheel error the message 10 will appear the fixture s display If an error message is displayed try powering the fixture off and then on again to reset it If the problem persists contact your Martin dealer Striking the EFX600 lamp If the EFX600 s discharge lamp is powered off via DMX during operation you must wait eight minutes before the lamp can be restruck If you try to strike the lamp anyway the message 102 will appear in the display Adjusting focus Focus can be adjusted from approx 2 meters 6 6 ft to approx 20 meters 66 ft lt w gt Operation 21 The focus adjustment knob is close to the lens aperture in the mirror drum cutout see illustration on right SERVICE AND MAINTENANCE Warning Important 22 The Mania EFX requires simple routine maintenance The maintenance schedule depends heavily on the operating environment Please consult a Martin service technician for recommendations Refer any service procedure not described h
36. ut up to 100 intensity using channel 2 The Mania EFX600 can be dimmed from 0 to 100 using the shutter on channel 1 Gobo wheel position rotation and music trig The gobo wheel can be positioned to project one of the colored gobos or at blackout The gobo wheel can also be spun in either direction or set to music trig in which gobos change with the music beat but the other effects are still controlled via DMX Mirror dish rotation and music trig The mirror dish can be spun in either direction for dynamic projection effects or set to music trig Pan The mirror drum pans swivels approx 180 A pan position can be selected pan can be set to narrow or wide shake or pan can be set to music trig Tilt The mirror drum tilts rotates 360 The drum can be held a stationary position set to rotate in either direction set to narrow or wide shake or set to music trig In DMX mode 2 the following additional functions can be controlled on two extra channels Macros On the first extra channel you can select one of twelve factory set macros Macros are pre programmed dynamic shows that use all the fixture s effects Effect speed On the second extra channel you can either select the speed at which effects change or select tracking Selecting a speed allows you to adjust fade times when using DMX controllers that do not feature fade time programming a fade time is the time taken for effects to change Mania EFX500 amp
37. with a safety strap 3 Remove the old lamp and socket from the lampholder clip and being careful not to strain any wires gently pull the lamp off its ceramic socket 4 Hold the new lamp by its base do not touch any other part of the lamp Push the lamp pins squarely into the ceramic socket 5 If you touched the bulb the reflector or any optical components clean them with a clean soft lint free cloth wetted with isopropyl alcohol and dry with a clean soft lint free cloth or compressed air 6 Replace the lamp and socket in the lampholder clip ensuring that the reflector sits flat against its plate and is held securely in place When installed correctly the rim of the reflector locates under the heads of two stop screws so that the reflector is held firmly between these screws and the lampholder clip 7 Close the lamp cover checking that no wires are trapped and retighten the thumbscrew Mania EFX600 lamp The Mania EFX600 uses a 150W long life discharge lamp For optimum lamp life always allow discharge lamps to warm up for at least 5 minutes before dousing Restriking the EFX600 lamp Note that when the Mania EFX600 s discharge lamp is powered off it must be allowed to cool for 8 minutes before it is restruck Mania EFX500 amp EFX600 user manual Warning Installing the EFX600 lamp Wear safety glasses and gloves and allow the Mania EFX600 to cool for at least 10 minutes before replacing the lamp 1
38. you detach the mounting plate from the fixture bolt the mounting plate to the surface and then reattach the fixture If you choose this method access for reattachment and adjustment can be easier if you remove the swivel locks and replace them with two M8 hexagonal lock nuts P N 08132701 Install an eyebolt and safety attachment once the fixture is mounted Installing the fixture and mounting plate as a unit If you prefer to install the fixture and mounting plate without separating them 1 Using the inside back cover of this manual as a guide drill three holes in the positions marked A 2 Screw three grade 8 8 minimum 8mm diameter 13mm head hex screwbolts or bolts into the holes at A amm but do not tighten them fully allow enough clearance between the bolt head and surface for the 3mm thick mounting plate 3 Fold the mounting plate so that it lies flat against the back of the fixture and tighten the swivel locks For easier access for adjustment it is possible to remove the swivel locks and replace them with two M8 hexagonal lock nuts P N 08132701 Mania EFX500 amp EFX600 user manual Important 4 Hold the fixture up to the surface so that the screwbolt heads pass through the centers of the keyholes A in the mounting plate and slide the fixture to engage the screwbolt heads in the mounting plate 5 Using one of the remaining holes in the mounting plate as a guide mark a position for a fourth h
Download Pdf Manuals
Related Search