Untitled - Commrider
Contents
1. RIDER TO RIDER COMMUNICATOR IC OMMRIDER COMMUNICATEUR DE PILOTE A PILOTE MANUAL COMMRIDER 7000 2 Button Open Face Communicator FR Se h 3 Bluetooth Www commrider com INTERNATIONAL Product Instructions The Commrider7000 Helmet Bluetooth headset enables you to answer phone calls enjoy music in your phone and keep clear inter communication with riders under safe and comfortable condition when driving a motorcycle snowmobile ATV or on the bicycle Charging audio input port Port pour recharge audio Sound Channel Switch on speaker Antenna Antenne 1 Volume Button Answer the call the intercom Paring the intercom call end the intercom shift inte reom FM Radio Volume volume down Blue LED Indicator 2 Volume Button Power on off Reject call Last number redial FM Search Volume up Play Pause Red LED Indicator Volume Note press and hold the volume key for 3 seconds you can switch freely between the three functions of Music play FM radio AUX in eat i Main Features Mobile phone functions e Bluetooth Hands free e Last number redial Automatically answer call e Reject a call e Independent Mobile phone volume control and memorize e Mobile phone highest priority Intercom functions e Rider to rider Maximum communication range up to 400m e Rider to pillion e 3 Riders connection e Switch conversation between 32. Wrong operation into test mode Because of wrong operation and going into the test mode the set must be charged up to two seconds to reset If above suggestions fail to solve your problem please contact us at info commrider com
3. and pair it with the Bluetooth headset and the headset read as default trust test permit automatically connection always visible allow to be found device and further ensure that the phone prompt tone is not on the vibrating mode the vibrating impulse wave would interfere with the Bluetooth signal some times then repair and connect with your mobile phone System Halt Freeze The system Halt Freeze when a strong radio frequency signal interference occurs Like when nearby high power TV transmission towers GSM base or airport radar the head set would die it can be reset by charging after be away from the interfere source Abnormal indication of charging indicator 1 When the headset haven t been used for a long time or overused it need to be pre charge for an hour then pull out and in the charger it will indicate normal charging Please don t count the pre charging time into the normal charging time 2 Try another charging line or charger 3 If the headset work well and the indicator doesn t illuminate when connected with the charger it is normal Compability with other chargers Cigarette lighter charger emergency battery pack or other type of charger might be used for charging as long as their actual output voltage is between 5V to 6V and have the same plug style and polarities with your initial charger You are solely responsible for using an other charger at your own risk and we can t guarantee it will work
4. conds to pause play your music Note above functions require the mobile phone to support the Bluetooth A2DP and AVRCP protocol FM Radio Operation Enter FM Radio Operation Bluetooth in standby state long pressing the VOL Button or about six seconds it can enter the radio function Channel Searching Double click the VOL Button to enter into the next channel AUX in function optional Connected to MP3 Player Ipod etc source via the external audio cable that we will provide it can be used as a cable headphones Connecting with GPS Navigator This helmet Bluetooth Headset fonction can be connected with a GPS Navigator As to the pairing operation please refer to the manual of your GPS Navigator Been paired you can hear the navigate voice or music througn the Bluetooth Headset Phone calls enjoy higher priority than the GPS Navigator the navigator voice can be transmitted to the Bluetooth headset only when there is no incoming calls Note Some GPS may occupy the HSP used by the mobile phone in that case only the GPS can be connected Automatic shutdown function When the Bluetooth Headset has no connection to any devices the headset will automatically turned off after 10 minutes Commrider7000 Bluetooth Helmet Headset LED Indicator Function Red LED Indicator Blue LED Indicator Red LED solid Charging completed Note 1 When charging the Bluetooth headset will reset the system Reopen the heads
5. et to use Charging the battery to full may takes about 5 hours 2 Communication time can reach about 8 hours and stand by time can up to 160 hours depends on different usage environment i FAQ Can not power on It might be low battery Please try again after charging the battery for 3 hours No sound Check if the speakers is fixed right or the volume is too low 16 the sound channel switch is in the correct position Speakers have after sound echo Maybe they are too close to the microphone Please move the speaker away from the microphone to a normal distance Disconnect from the mobile phone Make sure if the battery is not low if not is the distance between the headset and the mobile phone is 10m Or between them exists obstacles that block the signals like metals or water Can t pair with the mobile phone Clear all the pairing information according to the user manual and then put the headset and the mobile phone together within 1m and try to pair after entering the password 0000 Fail to connect with the mobile phone Make sure your mobile phone support the Bluetooth HFP A2DP and AVRCP or other related protocols fonctions Fail to reconnect or automatically reconnect with mobile phone Remouve all matching information according to the Bluetooth headset manual as well as that of your phone Thurn off your mobile phone and take out the battery for several seconds Restart the mobile phone
6. hest priority Mobile phone call can interrupt the intercom call The Intercom will be restored automatically after phone call ended Bluetooth Tripartite Interphone Function 1 For the first the three Bluetooth headsets must pair with each other For example there are three Commrider7000 units such as A B C unit A B A C B C all of pair successfully and not respond to any request of any other headset 2 When the three Bluetooth headsets all of pair successfully but without any intercom 2a Any one presses and holds Volume Button for 2 seconds it will connect the last intercom partner and begin to intercom 2b If double clicking Volume Button it will connect the third one the one before the last intercom partner and begin to intercom 3 During any two units intercoms the third one who is on standby state presses and holds Volume Button for 2 seconds it will send a connection request signal to the last intercom partner The being requested one will hear connection request sound of ring ring and then it must ends the current intercom and just double click Volume Button it will begin to intercom or just do nothing to ignore the request 4 During any two units intercoms the third one who is on standby state double clicks Volume Button it will send a connection request signal to the one of before the last intercom partner The being requested one will hear connection request sound of ring r
7. in the idle state Bleu LED with short flashing every 3 seconds a short press to the Vol gt button will initiate a connection to the headset Intercom operation Pairing Intercom Headsets 1 Press and hold VOL Button until Red Blue lights flashes alternately to enter Pairing Model 2 Short press Vol of either headset it will search the other one which in pairing Bluetooth state and then try to pair with it Note Please do not press both Vol while starting the search operation 3 Within a few seconds both headsets will turn off the Red light and then flashing slowly in Blue Pairing is finished 4 To pair with another headset repeat the above steps please 5 After pairing successfully just long press either of Vol button for 2 seconds then the Intercom function will be activated 6 Pairing is a one time process Once the headsets are paired during this setup proce dure they will remain paired and automatically recognize each other whenever they are within available range 7 Either of headset users wants to end the Intercom talking function just long press of Vol button for 2 seconds after heard the tone note release the button and then the Intercom function will be terminated 8 Short single click Vol Vol to adjust your Intercom volume till you feel good When reaching the maximum minimum volume a DiDong tone will be played 9 Mobile phone has hig
8. ing and then it must ends the current intercom and just double clicks Volume Button it will begin to intercom or just do nothing to ignore the request 5 If the either one of the two talking Riders wants to talk to the third one who Is on standby state it must ends the current intercom and just double clicks Volume Button to initiate intercom Hands Free Function Operation of Commrider7000 Helmet Bluetooth Headset Answering incoming calls Press Volume Volume button to answer when there is an incoming call or you can answer it with your mobile phone normally Automatically answer incoming calls The Bluetooth Helmet headset has the automatically answer function after 2 incoming call ring ones played about 8 seconds and if there is not any operations on the head set the Bluetooth Helmet headset will answer the phone call automatically Rejecting incoming calls Double press the Volume button to reject an incoming call Bluetooth Hang up In call active state press and hold VOL Button for about 2 seconds then release to hang up the call Last number redial Double press the VOL Button to redial the last called number when you are connected with the mobile phone Note the mobile phone has to support the Bluetooth Hands Free Protocol to use the reject and redial fonction Stereo Music Function Operation of Bluetooth Helmet Headset Pause Play Press and hold the VOL Button for about 2 se
9. n for about 8 seconds until a di tone played and the Blue and Red LED indicators flash alternately the headsets are on pairing mode the Bluetooth Headset can be searched and pairing only when it 16 On pairing mode Commrider7000 Helmet Bluetooth headset pairing with Mobile phone 1 Place the mobile phone and the Bluetooth Headset together within 1 meter A 2 Make sure the Bluetooth Headset is off Bluetooth 3 Press and hold the Vol button of the Bluetooth Helmet Headset for about 8 seconds until hearing a dudu tone and the Blue Red LED indicator flashes alternately then release the button 4 Initiate the Bluetooth function of the mobile phone and search the Bluetooth Headset according to your mobile user manual 5 Choose the Bluetooth devise with the name 96 7000 00 then press the OK button and after you will need to enter the pairing passwork 0000 then the indicator turn into a regular Blue light fash After that you will hear a di tone to indicate a succesful pairing Your Commrider7000 helmet Bluetooth headset is ready to use your voice and fonctions Note 1 Some mobile phone don t need to input pairing password because it can automatically complete the pairing process 2 After the mobile phone is paired with the Commrider7000 Headset the second time you turn on the headset it will auto connect with the mobile phone If they are not connected and the helmet Bluetooth headset isd
10. riders e Independent Intercom volume control and memorize Bluetooth e Intercom second priority after mobile phone e Typical effective range in urban area is about 300m e Note actual range will depend on weather conditions terrain and presence of obstacles Stereo functions e Bluetooth A2DP music Play e Enjoy music from Mobile phone or other music sources e Remote control music play with AVRCP e Independent music volume control and memorize 3 Bluetooth e Music third priority after phone call and intercom e Music volume soft restore back GPS functions e Audio guide information from Bluetooth GPS navigator by A2DP function or HFP e Independent volume control FM Radio functions e Frequency covers 76 108MHz e Independent FM volume control e Mobile phone highest priority Es A AUX in function optional e Mp3Player lpod etc source can be inputted to the Bluetooth headset a ey e Plug and play e Mobile phone highest priority Power On Off Power on the Bluetooth headset In power off state press and hold VOL Button for about 3 seconds until a short di tone played and the blue LED indicator flashes the headset is powered on Power off the Bluetooth headset In power on state press and hold VOL Button for about 8 seconds until a short di tone played and the blue LED indicator shut off the headset is powered off Pairing Mode In power off state press and hold the VOL Butto
Download Pdf Manuals
Related Search