V1.00.000 2012-10-23
Contents
1. is one LAUNCH TWC 712SMB Tire Changer User s Manual Repeat the same operations to mount the upper side of the tire WARNING dismounting and mounting are always done with the clockwise turntable rotation Anticlockwise rotation is used only to correct operator s errors or if the turntable stalls 5 Inflation The greatest attention is called for when inflating the tires Keep strictly to the following instructions since the tire changer is not designed and built to protect the user or anyone else in the vicinity of the machine if the tire bursts accidentally A burst tire can cause serious injury or even death of the operator Check carefully that the wheel rim and the tire are of the same size Check the state of wear of the tire and that it has no defects before beginning the installation stage Inflate the tire with brief jets of air checking the pressure after every jet Maximum inflating pressure is 3 5bar In any case never exceed the pressure recommended by the manufacturer Keep your hands and body as far away as possible from the tire 1 Tire Blasting There is a pedal on the side of the machine This pedal has two positions The first position is for the inflation for the tire with tube Step the pedal lightly for several times during the inflation Make sure the reading on the gauge does not exceed the manufacturer s limit The second position is for the inflation for the tubeless tire step the pedal down full2. A AAA Maa pies Mace C P GPITS Paneg 101 1110 4404 Pas bh 3130 Hiag Pas 00 1118 540 Tee HAIFA TA Maca fi F bhewise Fee bh Bie PHA tri 67 55 1164 0743 Fee PA 16 LAUNCH TWC 712SMB Tire Changer User s Manual Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER S BUSINESS LAUNCH electronic product is warranted against defects in materials and workmanship for one year 12 months from date of delivery to the user This warranty does not cover any part that has been abused altered used for a purpose other than for which it was intended or used in a manner inconsistent with instructions regarding use The exclusive remedy for any automotive meter found to be defective is repair or replacement and LAUNCH shall not be liable for any consequential or incidental damages Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH No agent employee or representative of LAUNCH has any authority to bind LAUNCH to any affirmation representation or warranty concerning LAUNCH automotive meters except as stated herein Disclaimer THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Order Information Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool suppli
3. H TWC 712SMB Tire Changer User s Manual CE Declaration of Conformity q LAUNCH TECH CO LTD Add Launch Industrial Park North of Wuho Avenue Banxuegang Bantian Longgang Shenzhen Guangdong P R China Zip Code 518112 Tel 86 755 84528861 86 755 84528859 Fax 66 755 64528872 http iwww enlaunch com CE Declaration of Conformity For the following equipment Product Name Tyre Changer Model Designation TWC 512RMB TWC 411NIC TWC 711TMB TWC 712SMB is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Low Voltage Directive 2006 95 EC and Machinery Directive 2006 42 EC For the evaluation regarding the Directives the following standards were applied ec EN 60204 1 2006 A1 2009 _ EN ISO12100 1 2003 A1 2009 EN 1SQ12100 2 2003 A 1 2009 EN ISO14121 1 2007 The following importer manufacturer is responsible for this declaration Company Name Importer Manufacturer gt Launch Tech Co Ltd eL Company Address Importer Manufacturer Launch Industrial Park North of Wuhe Rd Banxuegang Longgang Shenzhen China Person responsible for this declaration Name Surname Importer Manufacturer James Jiang Position Title Vice President i Legal Signature i AAA 211 aI 4 Place Date Launch Industrial Park North of Wuhe Rd June 29 2012 Banxuegang Longgang Shenzhen Ch
4. LAUNCH TWC 712SMB Tire Changer User s Manual ca iy VALL E A 4 If clamps or splitter open close slowly it is necessary to clean or replace the silencer and proceed as follows 1 Remove the left side panel of the machine 2 Unscrew the silencer put on the clamp opening closing pedal 3 Clean by a jet of compressed air or if damaged replace by referring to the spare parts catalogue 10 Right and Left Manipulator 1 Structure Please refer to the corresponding figure 10 Right Manipulator and 17 Left Manipulator The main pipeline connections for right and left manipulators are as shown in following figures 13 2 LAUNCH TWC 712SMB Tire Changer User s Manual Left Manipulator Connections Safety Requirement This machine may only be used by specially trained and authorized personnel 1 gt DS O Any tampering and modification to the equipment carried out without the manufacturer s prior authorization will free him from all responsibility for damage caused directly or indirectly by the above actions Keep it away from combustible and or explosive objectives avoid strong light sunshine and good ventilation Make sure to use original spare parts and accessories Installed by authorized personnel according to manual Be careful if there are any dangers happen stop the machine please contact us without hesitation Non operation personnel should be kept away from the machine Oper
5. V1 00 000 2012 10 23 LAUNCH TWC 712SMB Tire Changer User s Manual Trademark Information LAUNCH is a registered trademark of LAUNCH TECH CO LTD LAUNCH for short in China and other countries All other LAUNCH trademarks service marks domain names logos and company names referred to in this manual are either trademarks registered trademarks service marks domain names logos company names of or are otherwise the property of LAUNCH or its affiliates In countries where any of the LAUNCH trademarks service marks domain names logos and company names are not registered LAUNCH claims other rights associated with unregistered trademarks service marks domain names logos and company names Other products or company names referred to in this manual may be trademarks of their respective owners You may not use any trademark service mark domain name logo or company name of LAUNCH or any third party without permission from the owner of the applicable trademark service mark domain name logo or company name You may contact LAUNCH by visiting Launch at http www cnlaunch com or writing to Launch Industrial Park North of Wuhe Rd Banxuegang Longgang Shenzhen Guangdong P R China to request written permission to use Materials on this manual for purposes or for all other questions relating to this manual Copyright Information Copyright 2012 by LAUNCH TECH CO LTD All rights reserved No part of this publication may be rep
6. ators should be protected by protective materials glove eye protection glasses and working clothes etc to avoid any accidental injuries 14 N 0 LAUNCH TWC 712SMB Tire Changer User s Manual Unpacking Use proper tools and protection devices gloves etc to unpack the goods package Check that the equipment is in perfect condition making sure that no parts are damaged or missing if in doubt do not use the machine and contact your distributor Read the packing list carefully check if there is any missing if in doubt contact your distributor Put the packing materials plates nails screws plastic bags etc in safety place Deal with any contamination or dissolvable materials contained in the packing box according to local laws Installation Instructions for Left and Right Manipulators Open the packing for the well packed manipulator complete carefully and place it on one side of the splitter blade on the machine body Put one of the vertical arm padding plates 2 pieces machine onto the horizontal slot steel aim it at the hole on the slot steel Put the vertical arm complete onto the padding plate and aim it at the hole then thread the four bolts amp plain washers through the holes Place the other vertical padding plate onto the bolt below the slot steed install the plain washers spring washers amp the nuts in turn then fasten them carefully Connect the PU pipe with the joint of the device at last 15 LAUNC
7. cturers or for damage caused by tampering or removal of safety systems 2 Maintenance Operations Clean the turntable once a week with diesel fuel so as to prevent the formation of dirt and grease the clamp sliding guides LAUNCH TWC 712SMB Tire Changer User s Manual Carry out the following operations at least once every 30 days e Check the oil level in the lubricator tank 1 If necessary fill up by unscrewing screw 2 only use SAE30 oil e Check that a drop of oil is injected into the reservoir every 3 4 times the pedal is pressed one drop every 3 4 times pressing If not regulate using the screw 2 lf the oil is less than the minimum oil line please add the lubricating oil in time and if there is water in the water cup please pour it in time Please pay attention to the red line on the oil filter time by time Recommended Oil Lubricant ISO VG 32 Retighten the clamp tightening screws 1 and the screws on the turntable slides 2 If the turntable doesn t work it may be caused by loose drive belt check it as follows Before any operations please disconnect the electric power supplies Remove the left side body panel of the tire changer Tighten the drive belt by means of the special adjusting screw 1 on the motor support It is necessary to adjust the screw 1 in the locking plate of the mounting arm if the mounting head doesn t lock or it doesn t rise from the rim of 2mm necessary for working 12
8. e latest information available at the time of publication The right is reserved to make change at any time without notice Safety Precautions This manual is a necessary part of the product Please read carefully Keep the manual for later use when maintaining the machine This machine can only be used for the designated purposes Never use it for any other purpose The manufacturer is not held responsible for the damage incurred by improper use or use other than the intended purpose The equipment can only be operated by qualified personnel with special training Modification to any components or parts or use the machine for other purpose without either obtaining the agreement from the producer or observing the requirement of the instructions may lead to direct or indirect damage to the equipment This machine should be installed on the stable ground Keep the back panel 0 5m away from the wall for good ventilation Enough room should be left on both sides of the machine for convenient operation Do not put this machine in a place with high temperature or moisture or near the heating system water tap air humidifier or furnace Do not put the machine near the window with sunlight Protect the unit with a curtain or shield if necessary Avoid lots of dust ammonia alcohol thinner or spraying binder People who are no operating the machines should be kept away when it is used Use appropriate equipment and tools protective and safety equipment inc
9. e the tire and take off all the wheel balancing weights as shown in the following figure 1 Control Pedal Adjustment Caution The all four control pedals should be on the original positions before adjustment e Air Inflation Control Pedal lr Press the control pedal to the middle position the air inflation gun begins to work and press the control pedal to the lower position the air inflation gun and the small hole on the sliding block of the turntable begin emitting simultaneously LAUNCH TWC 712SMB Tire Changer User s Manual e Clamping Cylinder Control Pedal gt Press down the control pedal the clamping jaws are closed and press the control pedal again the clamping jaws are opened e Splitter Control Pedal dije Keep the control pedal pressed the splitter starts moving and when the control pedal is released the splitter will go back to the original position e Tire Lifting Device Control Pedal t Keep the control pedal pressed the tire lifting device will go upwards and when the control pedal is released to the original position the tire lifting device will go back to the original position too e Column Tilting Control Pedal ft Press the control pedal the column tilts backwards and press the control pedal once more the column go back to the original position e Turntable rotation control pedal 5 When the control pedal is pressed the turntable should turn in clockwise direction When
10. er Your order should include the following information Quantity Part number Item description Customer Service If you have any questions on the operation of the unit please contact us 4000666666 or 86 755 84528767 If your unit requires repair service return it to the manufacturer with a copy of the sales receipt and a note describing the problem If the unit is determined to be in warranty it will be repaired or replaced at no charge If the unit is determined to be out of warranty it will be repaired for a nominal service charge plus return freight Send the unit pre paid to Attn Overseas Department LAUNCH TECH CO LTD Launch Industrial Park North of Wuhe Rd Banxuegang Longgang Shenzhen Guangdong P R China 17
11. ge for long periods of time make sure to disconnect all sources of power and grease the clamp Sliding guides on the turntable to prevent from oxidizing 8 Scrapping If you decide scrape the machine be sure to make it inoperative by disconnecting it from all sources of power Remove all non ferrous materials and dispose of them as prescribed by national law Collect the oil and dispose of it at an authorized point as prescribed by national law scrape the rest ferrous material 9 Maintenance 1 General warning Unauthorized personnel may not carry out maintenance work Regular maintenance as described in the instructions is essential for correct operation and long lifetime of the tire changer If maintenance is not carried out regularly the operation and reliability of the machine may be compromised thus placing the operator and anyone else in the vicinity at risk Before carrying out any maintained work disconnect the electric and pneumatic supplies Moreover it is necessary to release the tire load less 3 4 times in order to let the air in pressure go out of the circuit Defective parts must be replaced exclusively by expert personnel using the manufacture s spare parts Removing or tampering with safety devices pressure limiting and regulating valves represents a contravention of safety regulations In particular the manufacturer shall not be held responsible for complaints deriving from the use of Spare parts made by other manufa
12. hanger read carefully the warnings and instructions contained in this manual since they provide important information on operation safety and maintenance Keep this manual for future reference Technical Data Relative humidity 30 95 LAUNCH TWC 712SMB Tire Changer User s Manual 2 Description of Machine LAUNCH TD wes A Lo 1 Tire lifting device 2 Air inflation control pedal 3 Tire lifting device control pedal 4 Clamping cylinder control pedal 5 Splitter control pedal 6 Turntable control pedal 7 Column tilting control pedal 8 Splitter 9 Splitter handle 10 Right manipulator 11 Right manipulator control bar 12 Head control bar 13 Tire lifting pneumatic cylinder 14 Locking control button 15 Releasing control button 16 Left manipulator control bar 17 Left manipulator 18 Tire holder pan 19 Mount Demount head 20 Jaw 21 Left holding block 22 Emission button 23 Right holding block 24 Tire depressor lateral bar LAUNCH TWC 712SMB Tire Changer User s Manual 3 Safety Requirement 1 Usage This tire changer has been designed and manufactured exclusively for demounting and mounting tires from into rims from 12 to 32 and with the maximum diameter of 1100mm Any other use is to be considered incorrect and unreasonable In particular the MANUFACTURER herein LAUNCH TECH CO LTD can t be held responsible for any damage caused through the use of this tire changer for purposes other than those specif
13. he locking button in the handle release hex bar LAUNCH TWC 712SMB Tire Changer User s Manual Lower the hex bar until the mounting tools rests against the edge of the rim Then lock it using the locking button in the handle This way the mounting arm is locked in a vertical and horizontal direction and the mounting head is automatically moved to a distance of about 2mm from the rim Do not put hands on the wheel when moving the mounting arm to its working position your hand could be crushed between the rim and the mounting head with the crowbar inserted between the tire and the front section of the mounting head move the tire over the mounting head ov WARNING In order not to damage the inner tube if there is one it is advisable to carry out this operation with the valve 10cm to the right of the mounting head LAUNCH TWC 712SMB Tire Changer User s Manual Chains bracelets loose clothing or foreign objectives in the vicinity of moving parts may cause danger to the operator With the crowbar held in this position rotate the turntable in a clockwise direction by pressing pedal 6 until the tire is completely separated from the wheel rim To prevent industrial accidents keep hands and other parts of the body as far as possible from the tool arm when the table top is turning Remove the inner tube if there is one need not release the mounting arm press pedal 4 directly tilt the vertical arm Repeat the ope
14. ied in this manual and therefore inappropriate incorrect and unreasonable 2 General Safety Precautions This tire changer may only be used by specially trained and authorized expert Any tampering and modification to the equipment carried out without the manufacturer s prior authorization will free him from all responsibility for damage caused directly or indirectly by the above actions The tire changer comes complete with instructions and warning transfers which are designed to be long lasting If they should for any reason be damaged or destroyed please ask immediately for replacements from LAUNCH Keep it away from combustible explosive objectives avoid strong light sunshine and keep it in good ventilation Make sure to use original spare parts and accessories installed by authorized personnel according to the Manual Be careful if there are any dangers happen stop the machine and contact us without any hesitation Non operation personnel should be kept away from the machine Operators should be protected by protective devices glove eye protection glasses and working clothes to avoid any accidental injuries 4 Operation Don t use the machine until you have read and understood the entire manual and the warnings it provides The operation of the tire changer is divided into three parts 1 Splitting the tire and wheel rim 2 Demounting the tire 3 Mounting the tire Warning before carrying out any operation deflat
15. ina as GERMANY UK SA CANADA RUSSIA SPAIN Achieve Made M E FZE Lamy Puipa anhi Laman h Austereo LHI Laure Tanh BA inp Id Peck Lipid ahii Ca ada Mz Lawns ir ro Co LTO Launch perra D L Round hirna Mot CE idecsrch tterts E 00450170 Uaa en intact Paii Mid Cary of indy Cate TG Heian Heri Line vaughan Bra 701 Buking 1 A hacen Pia donee Panaverce 7 8 Jebel AS Trga Lona Carpas Der ary Charlas Freri hata Tel 1 463 461 1580 Gwin Canada LAL JPE Proend Di Esplogosa de Ul babig PC Boe 170d Dubai Lai Tal ee 3773 BOTE Raihahaim PEL 157 TE UANL Far 1507 4080 150 Tal 1 M00 208 0030 Moscow FDR Espia ceia She Tai 84 BOTS Far III 0078 2 Tai dd 071504 SE apja ma r Pelos F 085 778 0 Tad 904 GF Ada Pan OPA MITI Far s i O Tp Anag RLE FLEE Fin 10 10 BES ETEA EELER SOUTH AFRICA JAPAN AUSTRALIA TAIWAM THAILAND MALAYSIA MEXICO Lesh Tarhaniagy GA P TY Lid Lawech Tash Japan in Lieno Teoh Piy Lid manch Meth Tiani Co La Lausrh Tach Tralsed on Lii Launch Jach iMi pih Eii Lentamente Lts Und J SiN Bur Par Ag dl ini Chin it Cospar Mi Bird WY 1E Hp 17 3 Da o Lat a OO Mos LI Hingise Mos Mo 1 Aman TPE I7 Ar inalituio Pit M trisial c bhaoi Crean jayo 104 003 2164 kuraia Dusan Tosmhip Prapuan Ranges Samuthpabein 12440 Teun Partnduntian erate OT COL Manna Agile JET Pare HOA A LO IA FER Taipi iT 7H 2008 Cammy 114 Taman Ilan Poo Puchong E BE Carchi Digo arras Tal FF 100 ti SOT PE ms be ee ee Faa 81 2 2 T og Tal Add J378 6050 Ml E
16. ire changer Press pedal 4 to tilt the vertical arm and clean the turntable Spread the grease onto the tire and the rim as shown in the above figure Failure to use the appropriate grease may cause the serious damage to the tire When clamping the tire never have your hand s under the tire To clamp the tire correctly position the wheel exactly aiming to the center of the turntable LAUNCH TWC 712SMB Tire Changer User s Manual Note Different clamping methods can be chosen according to different rims gt If you choose rim locking from inside please draw back the jaw first then place wheel on the turntable finally depress clamping cylinder pedal 9 tg clamp the rim gt f you choose rim locking from outside as shown in following figure stretch out the jaw first then place the wheel on the turntable to allow the two jaws inside to clamp on the rims hold the proximal side of tire by hands depress clamping cylinder pedal 9 to place pedal at low range jaws begin to tighten Observe the relative positions of the two proximal jaws to rims when they are close to the rim lower down the proximal side jaws will clamp the rim tightly Position the clamps so that they are completely closed Place the tire on the clamps and press the pedal 5 to open the clamp hand thereby lock the rim Make sure the rim is firmly fixed to the clamps Press the pedal 4 to restore the vertical arm to its working position Push out t
17. luding eyeglasses earplugs and working boots Pay special attention to the safety marks on the machine Do not touch or approach the moving parts by hand during operating Do not remove the safety device or override it Use 2 lithium lubricants grease only within the safety range Refer to the appendix for the safety data Before moving the tire changer contact maintenance personnel The product is better used under the following conditions Temperature 0 C 45 C Relative humidity 30 95 LAUNCH TWC 712SMB Tire Changer User s Manual Table of Contents le Warning SIGNS anG THEI POSIUON S A AAA 1 Zi MIO sore cn cceescesczcar co masan sa ccesaa aescascaoaa con cataunenca seca nensoaceeeatounstene cae ounsoen eae en enee on ateene 3 de Salely ROQUIPC Mii a 5 7 pam 01 1 1 918 ea nn eae ae eee 5 So non nn O 10 O IMOVINO A 11 Tee e e e AIA T T TIIE E A A A T TTT 11 is SDPN a cen satccccevaesecee cess cascce evescceccemes secercs esc rees mc ceesacmucenccieccer avciacesesececesece seesece ape seces seers seeneat 11 9z MAINTENANCE A A ai 11 105 RIghtiana Cer Mant Ul lat nics cos ssesco cesvrcosceeacoscaten senate soscatencesss tessa eee ened 13 CE Declaration Ol CONTO Ml acacia 16 LAUNCH TWC 712SMB Tire Changer User s Manual 1 Warning Signs and Their Positions Do not put your hand s between the MOUNT DEMOUNT head and the tire Please pay much attention to the pipeline connections Before operation the ai
18. r sources must be cut off and the air inside the machine must be emitted off in order to prevent the personnel from being injured Do not put your leg s between the splitter and the tire when the splitter is used Do not put your hand s between the tire and turntable when machine is operated Do not put your hand s and or other body parts between the jaws and the wheel rim when cylinder clamps fl 14 we Keep safety for electrified devices Do not stand within the column swing area to avoid personnel injury The pressure of compressed air cannot be more than 10bar Here is the connection joint of the air inflation gun please connect it with the pipeline of the compressed air Before inflation please check for the match between tire and rim otherwise it will be extremely dangerous to the operators around the machine LAUNCH TWC 712SMB Tire Changer User s Manual LAUNCH DP wens Please Pay Attention to the Following Please replace the safety signs if they get blurred or lost When one or more safety signs get lost don t operate the machine The safety signs must be kept within the sight of the operator LAUNCH TWC 712SMB Tire Changer User s Manual 2 Introduction Thank you for purchasing our tire changers The machine has been manufactured in accordance with the very best quality principles This manual is one integral part of the product Before using the tire c
19. ration for the other tire side 4 Mounting the Tire Warning this checking of tire and rim is of utmost importance to prevent tire explosion during the inflating operation Before beginning mounting operation make sure that The tire and the cord fabric are not damaged If you note the defects do not mount the tire The rim is without dents and is not warped Attention with alloy rims dents because internal micro cracks not visible to naked eye This can compromise the rim and also be the source of danger especially during inflation The diameter of the rim and tire are exactly the same Never try to mount a tire on a rim if you cannot identify the diameter of both Lubricate the tire with the special grease in order to avoid damaging them and to facilitate the mounting operations When tilting the vertical arm make sure that nobody stands behind the tire changer When you are working with the rims of the same size it is not necessary always to lock and unlock the hex bar Just tilt and restore the vertical arm with the horizontal arm and mounting arm locked Move the tire so that it passes below the front section of the mounting head and is brought up against the edge of the rear section of the mounting head itself Keep the tire pressed into the wheel rim channel with your hands and press the pedal 6 to rotate the turntable clockwise Continue until you have covered the whole circumference to the wheel rim insert the inner tube if there
20. roduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of LAUNCH The information contained herein is designed only for the use of this unit LAUNCH is not responsible for any use of this information as applied to other units Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages losses costs Or expenses incurred by purchaser or third parties as a result of accident misuse or abuse of this unit or unauthorized modifications repairs or alterations to this unit or failure to strictly comply with LAUNCH operating and maintenance instructions LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners LAUNCH disclaims any and all rights in those marks LAUNCH TWC 712SMB Tire Changer User s Manual This unit is made for the purpose of persons who have special techniques and certifications Disclaimer To take full advantage of the unit you should be familiar with tires of various kinds All information illustrations and specifications contained in this manual are based on th
21. the control pedal is pulled up the turntable should turn in the counterclockwise direction When the control pedal is released the turntable will stand still 2 Splitting the tire and wheel rim Warning when the splitter control pedal is operated anything within the action space of splitter arm can be in the danger of being crushed Check whether the tire is deflated or not if not please deflate it first Close the turntable clamps completely Warning splitter with the clamps in the open position can be extremely dangerous for operator s hands during the splitting operations never touch the side of the tire Position the wheel against the rubber stop on the right side of the tire changer Position the splitting blade against the tire upper side with a distance of about 1 cm from the rim Pay attention to the blade which must be correctly onto the tire not onto the rim Press the pedal 5 to activate the splitter and release it when the blade has reached to the end of its travel or in any case when the tire and wheel rim is split Rotate the tire slightly and repeat the operation around the entire circumference of the rim and from both sides until the tire is completely detached from the rim 3 Demounting the Tire Before any operations remove the old wheel balancing weights and check whether the tire is deflated or not if not please deflate it first When tilting the vertical arm be sure that nobody stands behind the t
22. y to the bottom and then make the pedal to the first position to continue the inflation Make sure that the reading on gauge doesn t exceed the manufacturer s limit 10 LAUNCH TWC 712SMB Tire Changer User s Manual Warning the operator should wear safety goggles when operating 2 Inflating tire using airline gauge Inflating a tire proceeds as follows Connect the airline gauge fitting to the tire valve Make a last check to be certain that the tire and rim diameter correspond Between air jets constantly check the pressure until required pressure has been reached explosion hazard Never exceed 3 5bar when inflating tire on a fixed position If a higher inflating pressure is required remove the wheel from the turntable and continue the inflation inside a special protection cage commercially available Never exceed the max Inflating pressure given by the tire manufacturer Always keep hands and body back from inflating tire Only specially trained personnel are allowed to perform these operations Do not allow other persons to operate or to stay near the tire changer 6 Moving Move the tire changer you need a fork lift Disconnect the pneumatic and electric power supplies Apply leverage to one side of the base so as to raise it slightly from the floor Insert the forks of the fork lift under the base and slide the tire changer onto them Set the tire changer down in its new position 7 Storage In the event of stora
Download Pdf Manuals
Related Search