INSTALLATION AND SETUP GUIDE
Contents
1. SIDE OF THE BATTERY MUST FACE THE TRIGGER 5869 006 VO Figure 2 5869 Battery Installation 2 Remove faulty battery and dispose of properly 3 Observing correct polarity negative side of the battery facing the trigger insert the battery into the battery holder as shown in Figure 1 4 Reinstall two cover screws and two mounting screws as shown in Figure 1 SPECIFICATIONS 1 15 16 W x 5 15 16 H x 1 3 16 D Physical 50mm x 150mm x 30mm PS aia Battery 3 volt Lithium ADEMCO 466 Duracell HOLE DL123A Panasonic CR123A Varta CR123A N BREAKAWAY TAMPER SCREW No 6X3 4 Frequency 345MHz Reset Key Supplied Part Number K4563 to order separately No 6x1 2 ea MOUNTING S7 ae Re MOUNTING l i en SCREW 2 Agency UL 636 Holdup alarm units and systems COVER ia SCREW 2 No 6x1 2 IMPORTANT z THIS DEVICE MUST BE PERMANENTLY 3 MOUNTED WITH THE SCREWS SUPPLIED 3 Figure 3 Typical Holdup Switch Installation BATTERY REPLACEMENT BATTERY CAUTION Risk of fire explosion and burns Do not recharge disas C U L U S semble heat above 100 C or incinerate Dispose of used batteries promptly and properly Keep away from children LISTED IMPORTANT When servicing the device for battery replacement note that with the mounting screws removed the case is held in place by the tamper release tab Exercise caution not to jar the case while replacing the battery possibly breaking2. the Tamper breakaway tab 1 Remove the two screws securing the cover and two mounting screws as shown in figure 1 NOTE Use care not to bend the antenna while attempting to remove or install the battery TO THE INSTALLER Regular maintenance and inspection at least annually by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts Recommendations must be included for a specific program of frequent testing at least weekly to insure the system s operation at all times FCC STATEMENT This device complies with Part 15 of the FCC Rules and RSS210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FEDERAL COMMUNICATIONS COMMISSION FCC PART 15 STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment CLASS B DIGITAL DEVICE STATEMENT NOTE This equipment has been test
3. Honeywell K5299V4 2 10 Rev A ADEMCO 5869 Holdup Switch Transmitter INSTALLATION AND SETUP GUIDE GENERAL INFORMATION The ADEMCO 5869 Holdup Switch Transmitter is a finger operated RF transmitting device used for activating a holdup signal at the security system control and or any other security application The 5869 is typically mounted under a counter or money draw for inconspicuous operation When the transmitter is activated it sends an RF signal to the control panel which then sends a burglary alarm to the central station Once the 5869 trigger Figure 1 is activated the supplied reset key K4563 must be used to reset the device The 5869 also contains tamper switches that are activated either when the cover is removed or when the unit is forcibly removed from its installation location The 5869 has a permanent serial number assigned during manufacture used for enrolling the 5869 with the security system control panel To enroll the 5869 refer to the respective Security System Control Panel Installation and Setup Guide For certified UL installations the 5869 must be used with the 5881ENHC tamper protected wireless receiver mounted inside its plastic enclosure and outside the alarm panel enclosure PROGRAMMING The 5869 Holdup Switch Transmitter should be programmed as a 24 hour silent zone type Refer to the Security System Control Panel Installation and Setup Guide for programming instructions NOTES e Du
4. ed and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help INDUSTRY CANADA IC STATEMENTS This device complies with RSS210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la n
5. orme NMB 003 du Canada WARRANTY INFORMATION For the latest warranty information please go to www honeywell com security hsc resources wa Honeywell 2 Corporate Center Drive Suite 100 P O Box 9040 Melville NY 11747 Copyright 2009 Honeywell International Inc www honeywell com securit K5299V4 2 10 Rev A
6. ring programming of the control panel the 5869 Holdup Switch Transmitter should be treated as RF i e supervised RF Type e The 5869 is one closed input loop zone loop 1 MOUNTING Mount the 5869 under a counter or money drawer for easy access by the cashier Refer to the figure and steps that follow for typical mounting installation Before mounting the 5869 permanently perform Go No Go tests to verify adequate transmitter signal strength at desired mounting location refer to the Security System Control Panel Installation and Setup Guide 1 Install the battery into the battery holder observing correct polarity as shown in Figure 2 2 Position the case to the desired location and install one No 6 x screw supplied at the breakaway tamper release hole as shown in Figure 3 3 Secure the cover to the case with the two screws No 6 x 1 2 as shown in Figure 3 IMPORTANT To prevent damage to the case do not over tighten the cover screws 4 Secure the case with the cover to its mounting location using the two screws No 6 x 2 supplied as shown in Figure 3 RESET KEY COVER ATTACH MOUNTING N PNL HOL TYP oo COVER Dy x COVER 7 SCREW 2 No 6X1 2 Ta A BREAKAWAY TAMPER SCREW No 6X3 4 MOUNTING SCREW 2 No 6X2 COVER SCREW 2 No 6X1 2 Figure 1 5869 Holdup Switch Transmitter Details TRIGGER 3V LITHIUM BATTERY ANTENNA NOTE THE NEGATIVE
Download Pdf Manuals
Related Search