IRIS.base installation manual (short)
Contents
1. FI system to avoid interference e the device is not water resistant it should be in a dry location e if it s possible it should be hidden in a place that s hard to reach in order to make any sabotage action more difficult Optin Kft en optin hu rev EN 11 515 May 2014 QO IRIS base Short installation guide 2 PLACEMENT TIPS IN A CAR e behind the dashboard e behind the glove compartment e center console e under the front seats e under the carpet between the front seats e in the trunk Figure 1 Placement tips 3141 PLACING OF THE GPS ANTENNA The active receiver of GPS antenna should be placed in a way that it s the least shielded from the satel lites For example it can be fastened with a double sided tape to the dashboard or the A pillar where the carpet and the windshield adjoin It can also be installed the same way at the rear window or outside of the roof if it s possible Plastic components may shield the GPS receiver 3 2 CONNECTING THE SYSTEM CONNECTOR The system connectors from the rear view of the fa 3 5 7 9 Jaaji3 a5 IRIS base device 2 4 6 8 10 12 14 16 System Connector external power supply 8 30V DC 2 ground GND digital output 1 D01 digital output 2 DO 2 OD max 1A OD max 1A analogue input 1 Al analogue input 2 Al 2 CAN L CAN H digital input 2 DI 2 see optional functions ignition signal D11 digital input 3 DI 3 see optional functi2. QD IRIS base Short installation guide 4 Figure 2 IRIS base inner view 1 Battery connector 2 SIM card 3 microSD card 4 expansion board WARNING A e The device s battery should only be connected if can be connected it to an external power supply within a short period otherwise the battery charge may deplete e Only qualified official personnel may repair the product Troubleshooting and simple reapirs can only be made as described in the User Manual e To avoid any electrostatic discharge ground yourself with a bracelet or touch an unpainted metal Surface frequently e Treat the components and the card carefully Don t touch the card s components and interface The card must be held on it s outer sides 5 SUPPORT If you are stuck Somewhere need help or just have some questions about the product please contact us at hwdev optin hu Optin Kft en optin hu rev EN 11 515 May 2014
3. QO IRIS base Short installation guide 1 1 OVERVIEW This is a short version of the installation manual and contains the most important information about the placement of the device and the installation of the system connector You can find the complete version at the website at http en optin hu products services iris base 11 PACKAGE CONTENTS Thank you for choosing the ON GUARD web application and the IRIS base on board unit Your package contains the following items for each vehicle e IRIS base or IRIS base BT on board unit with a pre installed SIM card e 4 screws for the box lid e GPS antenna with cable e GSM antenna e System Connector e Short installation manual Optional accessories can be bought in our webshop en optin hu shop 2 SPECIFICATIONS 2 1 DIMENSIONS The device s dimensions are 80x60x30 mm L x W x H With the flange the width is 104 mm and the size of the antenna and the system con OQ nector should also be taken into consideration when choosing the place of the de vice 3 PLACEMENT Choose a place in the car that s big enough and meets the following criteria e the device is in a stable position to avoid dislocation otherwise the data coming from the vibration sensor will not be accurate If possible place it horizontally e there should be enough room for the antennas and the connectors e the cable of the GPS antenna reaches the device e the GSM antenna should not be too close to the car s HI
4. ons digital input 4 DI 4 see optional functions digital input 5 DI 5 see optional functions digital input 6 DI 6 see optional functions a co 9 1Wire data cable 2 ground GND Optin Kft en optin hu rev EN 11 515 May 2014 Q IRIS base Short installation guide 3 NECESSARY CONNECTIONS The following three cables must be connected External power supply the system connector s RED cable at the 1 slot must be connected to a fixed 12V or 24V point Ground the system s ground the BLACK cable at the 2 slot Ignition signal the BLACK cable at the 11 slot This should be connected to a point that only has 12V or 24V when the vehicle s ignition system is turned on This controls the device s operation modes OPTIONAL CONNECTIONS These connections are not obligatory but the ON GUARD webapplication s certain functions are only available with the existence of the corresponding connections Business personal usage switch the 2 digital input DI 2 which is the GREEN cable in the 12 slot of the system connector Panic button the 3 digital input the YELLOW cable at the 13 slot Digital inputs further digital inputs for general applications GREY cables In a security application the 4 digital input DI 4 works as a door opener sensor the 5 digital input DI 5 works as a hidden button Analogue inputs through the PINK cable at the connector s 5 and 6
5. slot the device can measure a O 5V voltage iButton identifier the BLUE cable at the 9 slot of the system connector should be connected to the iButton reader s central interface CAN FMS connector PURPLE cables can be connected to the vehicle s FMS system for further devel opments Switch outputs ORANGE cables they provide the so called open drain outputs that is capable of draining a maximum of 1A current In a security application the 1 digital output DO 1 which is the 3 slot of the system connector should be connected to the solenoid starter s emergency stop relay The 2 digital output DO 2 4 slot should be connected to the vehicle s alarm 4 FIRST INSTALLATION e After removing the 4 screws remove the lid from the box by lifting than twisting than pulling it backwards towards the antenna from the front panel e The SIM card is an essential part of the ON GUARD service It only works on this device and is only capable of data transmission Don t remove it e If you have a device capable of Bluetooth connection you can connect the cable of the expansion board to the on board unit s Bluetooth unit e If you would like to use an SD card just slide it into the microSD socket e Connect the three pole battery installed in the lid to the indicated place e Screw back the lid Be careful Fastening the screws too hard may damage the plastic compart ments Optin Kft en optin hu rev EN 11 515 May 2014
Download Pdf Manuals
Related Search