Page 1 SP 2000 USER MANUAL SpacePak Series Photoelectric
Contents
1. SP 2000 USER MANUAL EN eon SpacePak Series Telco Poh Photoelectric background suppression Product Data Mounting amp Alignment Electrical Data Mounting amp Installation DC AC Ae a Supply Voltage 10 30 V dc 12 240 V dc 20 240 V ac 1 Position the sensor pointing at the target object Voltage ripple 15 Reverse polarity protected Yes 2 Align by moving sensor horizontally and vertically until the output changes when the Short circuit protected Yes target object is present refer to Output Logic table Current consumption lt 65 mA lt 70 mA 1 open 1 close 3 Fasten the sensor securely using the enclosed mounting bracket and hardware Avoid Output relay z 240Vac 3A acute angles on cable close to sensor Output transistor 200 mA 30 V de v Environmental Data Temperature operation 20 to 55 C Sealing class IP 67 LSZ i y lt b Approvals A rs ce Lf Available Models Sensing Model Supply Voltage Output Time Delay Range SPBS 2600 T On Off Delay Adjustments SPBS 2600 10 30 V de NPN PNP x 0 05 m SPBS 2900 T 12 240 V dc On Off Delay adjustable Output Mode Selection SPBS 2900 20 240 V ac Seay TEET 7 r 7 z The output mode can be selected via an integral light dark switch Refer to Output Logic table Diffuse SPBS 2601 10 302. Place target object in correct position to the SPBS and at the required distance Wiring Diagrams Increase sensitivity slowly from minimum full counter clockwise until the yellow 3 output indicator changes Increase a little further until the red Insufficient Signal Brown 4 i Brown b 4 indicator is off If the output has not changed attempt to move sensor closer to Load wi target object and repeat procedure it Re a Black b NC Black 4 4 Remove target object If output changes the sensitivity is adjusted correctly If the Bi 3 Bi 3 output does not change then proceed to step 5 ue 2 lue x NC Do not connect wire NC Do not connect wire 5 Place target object in correct position Decrease the sensitivity by turning the gain potentiometer counter clockwise until the red Insufficient Signal indicator is on SPBS 260x SPBS 260x Load as NPN Load as PNP A eee t R 6 Remove target object If the output changes the sensitivity is adjusted to suit the target but the adjustment is very delicate and not advisable Brown D 43 Grey __ gt N C 7 f the output does not change the target object is placed too close to surrounding White objects Please contact your vendor for further information a gt Black D NO Bue _p Time Delay Adjustment T models The on delay enables output signal to only activate if an object in the detection area is present for the adjusted time period In Light operated mode SPBS 290x The off del bl ign
3. V de npN pnp On Off Delay for output mode reference Proximity SPBS 2601 0 1 5 m TEN 5 Se ae background SPBS 2901 T 12 240 V de On Off Delay adjustable i nables the output to be active urn switch to full clockwise suppression SPBS 2901 20 240 V ac Relay 3 Light Operated N O when there is an object present position SPBS 2602 T On Off Delay E inacti i 10 30 V de NPN PNP nables the output to be inactive Turn switch to full counter SPBS 2602 E 0 2m Dark Operated N C when there is an object present clockwise position SPBS 2902 T 12 240 V dc Rela On Off Delay adjustable SPBS 2902 20 240 V ac y OMINIE Note Measured against matt white A4 paper Rela Teee Output Detection Output mode y uD Illustration Output Output indicator Object present Dark operated NO Nc N C ho Open Off SU N i C NO INC are Led Indicators Bom oparaied Closed On le N O O Indicators Signal status red Li Object absent Light operated c No nc o Off FN N O S pen P Sensitivity adjustment O Output yellow r N Dark operated c No Nc Power Closed On Ko lt 4 DarkLight switch _Power green N C ar 5 I mm a an lt On delay adjustment only T models Sensitivity Adjustment ZNE A R Off delay adjustment only T models Proceed with the following steps 1 Start with the sensitivity at minimum by turning the potentiometer to full counter clockwise position Connection 2
4. al in activated for the adjusted ti iod Relay output e off delay enables output signal to remain activated for the adjusted time period The time delay is adjustable between 0 10 sec Connection Wires Pins Onea Increase or decrease on delay by turning potentiometer clockwise or Cable 4 pin M12 plug y counter clockwise respectively Supply Supply ac Brown Pin 1 Brown F Supply Supply ac Blue Pin 3 Blue Off delay Increase or decrease off delay by turning potentiometer clockwise or Output NC Grey counter clockwise respectively Output NO Black Output COM White Output PNP Black Pin 4 Black s i Output NPN White Pin 2 White A e Website www telcosensors com Warning V1 11 Part Number 0666220634 E Mail info telcosensors com Made in Denmark This product is not a safety system and must not be used as such It is not designed for personnel safety applications and must not be used as a stand alone personnel safety system January 2011 edition Telco A S reserves the right to make changes without prior notice
Download Pdf Manuals
Related Search