GSM module G10
Contents
1. PING signal dialled in DTMF tones E 770 st R gt E 14499 999 R 14499 999 Input mode Activated restored ANNEX2 Texts of SMS messages which are sent to mobile phone after occurring particular event Control panel Sent CID code Existing In CID standard E 100 MEDICAL PANIC ALARM Medical Alarm R 100 E 110 FIRE PANIC ALARM Fire Alarm R 100 E 120 PANIC ALARM Panic Alarm R 120 E 121 DURESS ALARM Duress Alarm E 130 ALARM Burglary Alarm R130 Alarm restore Burglary Alarm restore E 301 AC Power failure on control panel AC Loss R 301 AC Power failure restored on control panel AC Loss restore kas L Low System battery R 302 Low system Battery restore ma L pel R321 Bell 1 restore m E 351 Telco 1 fault R 351 Telco 1 fault restore E R 400 401 E 401 OPEN by Open by user 406 451 R 401 CLOSE by Close by user E4 ick DISARM ick DISARM E R 408 08 ule S Sue S R 408 Quick ARM Quick ARM E 602 E 602 Periodic Test Periodic test report E R 100 E R 110 115 E R 120 E R 130 144 E R 301 122. DATA lt IN1 lt OUT lt IN2 lt COM lt MCI duomenys data Aanwe SECOLink nuoseklus i jimas SECOLink serial output SECOLink nocneposaTrentxem BEIxon Wiring diagram to SECOLink security control panels PAS8xx Setting of operating parameters Module G10 operating parameters are set with computer program G10config Program can be found in website www trikdis lt 1 Connect the module G10 with a computer using a USB cable Note USB drivers must be installed in the computer If the module is connected to a computer for the first time MS Windows OS should open the window Found New Hardware Wizard for installing USB drivers Download the USB driver file USB COM inf for MS Windows OS from the website www trikdis lt In the wizard window select the function Yes this time only and press the button Next When the window Please choose your search and installation options opens press the button Browse and select the place where the file USB COM inf was saved Follow the remaining wizard instructions to finish the USB driver installation 2 Start the program G10config 3 Select the program directory Settings Pott coms V H In the drop down list Port select the port to which the module is connected Language Engish T Note specific port to which the device is connected will appear only when the device is properly connected In the drop down list Language select the desired program language 4 Press the button Conn
3. DATA o Data signal clamp K KET aa uu I input dlamp NC type O O POUT Output clamp OC type IND 2 inputclamp NC type K O aaa L COM gt TEC an R PMG Provided for future use OOK Clg Light indication BRT I O 2 217 Network displays connection with T Green ON i Module is connected to GSM network GSM network status Yelow ON Message is being sent Green flashing Connecting to GSM network ene Yellow flashing Number of yellow flashes represent GSM signal strength l Data displays data buffer status i Green ON Unsent messages present in module memory a Red ON Unable to be sent messages Green flashing ee i Messages are being received from the control panel Red flashing rapidly SIM card error BL Red flashing Module configuration is incorrect i Power displays power supply status Green flashing ee Power supply is sufficient microcontroller is functioning i functioning of microcontrollerand Yellow flashing Power supply is not sufficient 11 5 V microcontroller is functioning Programming status Green and yellow flashing in turn Programming mode Installation E 1 124 Actions El LO Notes i 1 Set module operating parameters Follow information in chapter Setting Operating Parameters 2 Insert an activated SIM card Contact a GSM service provider in order
4. Description of syntax CONNECT Enter the word CONNECT means starting command Enter your 4 digit access code to module parameter configuration default is 0874 m a EET Enter the word SERVER enter IP address of the IP receiver from which SERVER value m Module operating parameters will be configured Enter the word PORT enter port of the receiver from which module PORT value EES i operating parameters will be configured Enter the word APN enter the GPRS access point name of network where APN value SIM card is operating If GSM service provider doesn t require any value must S be entered just leave spaseAPN space In SMS Enter the word USR enter the User name of GPRS access point name of USR value network where SIM card is operating If GSM service provider doesn t reguire BI any value must be entered just leave spaceUSREspace IN SMS Enter the word PSW enter the Password of GPRS access point name of PSW value network where SIM card is operating If GSM service provider doesn t require a rE any value must be entered just leave spacePSW space N SMS T A Enter the word ENCR enter the 6 digit messages decrypting key which is en O Set in IP receiver default is 123456 Order of actions after the message is sent 1 Open the window of software Pcom and select the object ID wh
5. PC1832 PC1864 PC585 PC1565 PC5020 raudonas red kpacHbii juodas black s pribiA lt COM lt CLK lt DATA lt IN1 lt OUTI lt IN2 lt COM lt MCI alias green sen HHbiA AUX jimas input Bxog Pyronix duomen magistral Pyronix keybus Pyronix WHHa aHHBIX i jimas output BbIxO Wiring diagram to Pyronix Matrix Series security control panels MATRIX 424 MATRIX 832 MATRIX 832 MATRIX 6 MATRIX 816 maitinimas power nuTaH4e maitinimas power nMTaHMe lt COM lt CLK lt DATA lt IN1 lt OUT lt IN2 lt COM lt MCI duomenys data AaKHble jimas input 7 BxoA Paradox nuoseklus i jimas Paradox serial output 8 i jimas output Beixog Paradox nocnegoBaTenbHbI BbIXOA Wiring diagram to Paradox security control panels SPECTRA SP5500 SP6000 SP7000 1727 1728 1738 MAGELLAN MG5000 MG5050 DIGIPLEX EVO48 EVO192 EVO96 NE96 ESPRIT E55 728ULT 738ULT raudonas red KpacHbii juodas black u prei i alias green 3en HHbi lt IN1 lt IN2 POS jimas input Bxog Caddx duomen magistral Caddx keybus CaddximHa panukli i jimas output Bbixog Wiring diagram to Caddx security control panels NX 4 NX 6 NX 8 lt COM lt CLK lt DATA lt OUT lt COM lt MCI maitinimas power MTA Me lt COM lt CLK lt
6. Primary reporting The section is for setting a primary communication channel through which the module will transmit messages to an alarm receiving centre ARC If GPRS is selected IP1 address or domain name of ARC and a port number of the server must be specified in the corresponding boxes Server IP1 address or Domain and Port If DATA is selected enter telephone number of PSTN line receiver of ARC in the box Tel 1 to which module will dial messages in DTMF tones The telephone number must be entered with international country code without the plus sign If SMS is selected enter telephone number of the SMS receiver of ARC in the box Tel 1 to which module will send with SMS messages The telephone number must be entered with international country code without the plus sign Backup reporting The section is for setting a backup communication channel through which the module will transmit messages if connection through the primary communication channel has been lost If GPRS is selected IP2 address or domain name of ARC and a port number of the server must be specified in the corresponding boxes Server IP2 address or Domain and Port If DATA is selected enter telephone number of PSTN line receiver of ARC in the box Tel 2 to which module will dial messages in DTMF tones The telephone number must be entered with international country code without the plus sign If SMS is selected enter telephone number o
7. services provided by the GSM GPRS Internet service providers UAB TRIKDIS is not responsible if GSM GPRS Internet services are not provided to the Buyer and or User of the Device or were cancelled and any direct or indirect damages were incurred thereof UAB TRIKDIS is not responsible for any direct or indirect damages incurred by the Buyer and or User of the Device due to loss of electricity UAB TRIKDIS is not liable if Device firmware versions were not updated by the Buyer and or the User on time User manual of the Device can contain technical inaccuracies grammatical or typographical errors UAB TRIKDIS reserves the right to correct update and or change information in the installation manual GSM module G10 Module G10 is designed to transmit messages from security control panel in a secured object to an alarm receiving centre ARC through a GSM network Module features Messages to ARC can be transmitted through GPRS with SMS messages or dialled in DTMF tones Messages are sent through a communication channel set as primary and in case of this connection failure through a backup channel Even though the GPRS connection with two servers will be lost information can be sent in SMS messages Sent messages correspond to Contact ID protocol codes SMS messages can be sent to 4 user mobile phones Output OUT1 status can be controlled remotely Operating parameters and firmwar
8. B Open Fa Save F5 Hame Telephone 370123123456 370321654321 3704561 23456 Alarm Restore Open Close Service Module Settings i Firmware O R RK K OORO SMS language fi ENGLISH WWIH1252 Send SMS which Described Only Account name Account Name Users 001 John 001 Entry door 002 User 002 Zone z O34 User 34 O28 Zone 28 123 Userl 23 O56 Zone 56 Partitions M House U Garage 06 Partition 6 Dev G10 SM 002743 Ver 1 41 Connected Telephone The list is for entering telephone numbers of the users to which SMS messages will be sent T1 T2 T3 T4 Numbers must be entered with international country code without the plus sign Name By selecting the check boxes SMS message sending condition to user can be set Alarm Restore SMS messages will be sent if the security system is alarmed restored events with code E R 1xx Open Close SMS messages will be sent if the security system is armed disarmed events with code E R 4xx Troubles SMS message will be sent if system troubles occur events with code E R 3xx Tests System Test will be sent in SMS message events with code E 602 SMS encoding Here can be set desirable SMS text character encoding Send SMS When Allis set SMS messages will be sent to user about all events of security control panel When Described Only is set module will send SMS messages about events in described zones only Object ID Field where the obje
9. Password for connecting to the GSM network DNS1 DNS2 Default addresses must be left if GSM network operator did not provide other values Administrator of an alarm receiving centre must provide the IP address port telephone numbers encryption protocol key and other parameters needed for connection with the ARC APN name and password should be provided by the GSM network operator from which you have received the SIM card Module events The table presents module events after which occurring messages will be sent Event code can be changed by double clicking the cell Contact ID event code or Contact ID restore code and by entering exact values in a newly opened window for setting entered values press the button OK in newly opened window m Module events E event description Reventdescription TIME Internal clock of the module is not set Internal clock of the module is set POWER Power supply voltage is lower than 11 5V Power supply voltage hasrestoredto12 6V TAMPER1 Input N1 external circuit is broken Input N1 external circuit is restored TAMPER 2 Input N2 external circuit is broken Input N2 external circuit is restored eo EEE EE i E EEE PPP Pp ppyyyppppypppppppppppyPppy pp Pppyppppppppppppppp In the directory Text SMS to user enter the parameters which are necessary to send SMS messages to users Eix Fie About Disconnect FFS Read F7 Open Last F4 Write F
10. Save access code Read after connection Restore defaults settings Restore F11 SH 002743 Ver 1 41 Connected Section for entering a 4 digit object identification code Section for entering a SIM card PIN code Leave this field blank if PIN code request is disabled Section for entering a User code When connected using a User code only those module parameters can be changed which change were allowed by the administrator Section for entering an administrator code When connected using an Administrator code all module parameters can be changed and access to parameter change for persons connecting with the User code can be restricted Select the security control panel type which is connected to the module G10 If one of an interface C11 or C14 or CZ6 is connected to the module select the option INTERFACE C11 C14 CZ6 When the option 24h zone is selected in the drop down list module will transmit a message with a code set in the table Module events after braking restoring input N1 external circuit When the option Backup mode is selected transmitting security control panel messages will be allowed after breaking input N1 external circuit If the option Remote control SMS is selected in the drop down list the module will change its output state after receiving an SMS message containing a control command See chapter Remote output state control If the option Lost Primary channel is selected output state will change to the opposit
11. a etree cetera time period given in seconds E Key _ means space tab Spacesin RESET 1234 Restart module notified places must be entered eee ee ee ee ee a a a aa a aa a a a a a a paa aa Be ae ee a ae ee ne ne eens ae ee ee saa ae Te a Sa a ae ET ee aN SS SS ne ee Power supply voltage DC12 6 3V 1 pan nnnn nnn nnn nnn nnn nnn nnn nnn mama mamania aaa T 4 1 1 1 1 1 1 eean 60 100 mA stand by Up to 250 mA transmitting a eee l L GSM modem frequency L 850 900 1800 MHz SOL C110 E a SPU RU cece ee ee r Inputs 2NCtype Output 1 OC type commutating up to 30 V voltage and currentupto1A Setting configuration Through the USB port Z Z Operating environment From 10 C to 50 C with relative air humidity 80 when 20 C Dimensions i 65 x 79x25mm tt el tt et i a a a a a a a a a a a a i a a a a ER Package contents Module G10 1 pc Two sided adhesive tape 10 cm 1 pc Note CRP2 cables and GSM antennas of desired type are collected by the additional request 11 ANNEX 1 Non alarm events transmitted to ARC Bee teat ae oe i Activated Device TEST message E 602 Time is specified yes no Connection with the security panel lost restored E 700 Not specified E 702 PING signal through SMS channel E 750 Connection by SMS channel E751 lost restored PING signal through GPRS channel E 760 Connection by GPRS channel E 761 lost restored
12. ct name might be entered It will be included in the SMS message Users Table entries are linked with codes of users who can arm disarm the security system User who arms disarms security system by entering its own code his or her name will be included in the SMS message Zones Table entries are linked with events in zones under protection When zone is disturbed restored entered zone name will be included in the SMS message Partitions If the security system is divided into several independent protected areas the table entries are linked with these areas When area zone is disturbed restored entered area name will be included in the SMS message 6 Press the button Write F6 and values entered in the program G10config windows will be uploaded to the module G10 7 Press the button Disconnect F8 and unplug the USB cable from the USB socket Save F5 By pressing this button values entered to the program G10config will be saved to the computer A file with extension gst will be created It can be used later as a template to configure other modules Restore F11 Press this button if is necessary to restore default factory operating parameters Press the button Yes when request window opens Firmware version upgrading When the manufacturer adds new features to the module G10 firmware of the previously bought module can be updated 1 Download the latest G10_xxx prg update file from the website www trikdis It 2 Conne
13. ct the module G10 to a computer and start the program Gi0config Open directory Firmware and select the file G10 xxx prg saved in the computer 3 Press the button Start F9 Wait until file uploading bar Progress reaches 100 then press the button Disconnect F8 and unplug the USB cable 4 Plug the USB cable back in Firmware updating process starts This may take 60 90 seconds Wait until indicator Data stops flashing green and then press the buttons Connect F2 and Read F7 The new firmware version will be displayed in G10config program status bar Setting of configuration remotely In order to set module G10 operating parameters remotely a SMS message with the particular syntax must be sent by GSM number of SIM card put in the module G10 When the module G10 receives this SMS message it opens GPRS communication session with software Pcom Wireless programming phones If during the previous setting module operating parameters were being entered GSM number of authorised person in the list G10Oconfig Settings Wireless TOI programming phones the module G10 will open GPRS communication session if it L receives SMS message with particular syntax from authorized person s phone TO4 SMS message text structure word space Means space between SMS text symbols CONNECT pace 234spaceSERVER 100 100 100 1005pacePORT 1000 paceAPN providerspaceUSR NAMC paceP SW PSWepace E NCR enc Note entering values use capital letters
14. e after losing communication through the primary channel When the option Lost Secondary channel is selected output state will change to the opposite after losing communication through the backup channel If the option Lost Both channels is selected output state will change to the opposite after losing communication through the primary and backup channels Time interval according to which the module sends signals PING for checking GPRS connection Time interval according to which the module dials signals PING for checking GSM connection Time interval according to which the module sends signals PING for checking transmitting over SMSC Time interval according to which the module sends its Test message The directory GPRS Enter the parameters needed for reporting to an alarm receiving centre ARC IE File About Disconnect F2 FB Read F7 pen Last F4 Write FB Open F3 Save F5 Primary reporting Backup reporting j Text H Settings Server IP address Server P2 address i Firmware or Domain or Domai Fort Teli APH User Protocal Password Encryption key DNS 195 22 175 1 fi 34 176 32 129 Return to primary after Backup reporting after 2 attempts Module events Contact ID event code Contact ID restore code E 700 99 999 R 700 99 999 E 602 99 999 E 502 339 355 F 502 95 555 E 144 95 001 R 144 55 001 E 14499 002 R 144 95 002 Dev G10 SH 002743 Ver 1 41 Connected
15. e version can be updated remotely Operating parameters are set with program G10config Operation When connected to a DSC Caddx Paradox or Pyronix security control panel data bus the module receives its messages and transmits them to an alarm receiving centre ARC over set communication channel If a message fails to be transmitted through this communication channel the module can send the message through a backup channel If there are set 2 IP addresses in module and module loses GPRS connection with them information can be sent to ARC in SMS messages The module can send messages to specified recipients about breaking restoring external circuit of inputs N1 and N2 The module can periodically send signals P NG for controlling the connection Messages can be sent with SMS messages to 4 mobile phones There is possible assign understandable text to every security control panel event Module output OUT1 state will change when connection with server of ARC fails restores or when the module receives an SMS message containing of command to change its output state Outside view 1 Terminal block 2 SIM card holder 3 USB socket 4 GSM antenna 5 indicator Network 6 indicator Data 7 indicator Power a a O EEEE CM ae SS oe St nn th tt th th tn Ph LL 1 Contact eee Purpose eee i m E OO i 12V power supply clamp COM Common clamp i a CLK O O ee ia Synchronizing signal clamp
16. ect Disconnect F2 F8 When the module G10 is connected to a computer module LED Power should flash green and yellow in turn Program Gi10config File About B i status bar should indicate connection status as Connected and Connect Disconnect F2 F 9 the following information about the connected module Dev GID Module type z GPRS reporting 2 Text SMS reporting SH OUT 4 Module serial number Settings Firmware Ver 1 33 Firmware version installed in the module 5 Press the button Read F7 x When the window Access code opens enter the access code default access code is 1234 and press the button OK If you want for the program to remember your access code check the box Remember The window Access code will not open when connecting to the module for the next time Remember Select the program directory Main and set the following parameters AEE File About Disconnect F2 F 9 Read F7 pen Last F4 Write FB Open Fa Save F5 GPRS reporting Text 5M5 reporting i Settings i Firmware Object ID SIM Card PIN code User code Admin code Panel type IN1 PGM GPRS PING time CSD PING time SMS PING time Test time Account name fan W Hes SIM Card PIN fan GPRS ping time User code 1234 CSD ping time 4 digits Admin code 1234 SMS ping time ss Test time Panel type a OSC PCS85 PC1565 PCB020 Ind Input mode r Fiemote control SWS
17. f the SMS receiver of ARC in the box Tel 2 to which module will send with SMS messages The telephone number must be entered with international country code without the plus sign Second backup Telephone number of SMS receiver of ARC to which the module will send SMS messages if the reporting tel module has lost GPRS connection with two servers This option is allowed only if both primary and backup communication channels are selected as GPRS The telephone number must be entered with international country code without the plus sign Protocol The drop down list is for selecting a protocol for encrypting messages Encryption key The section is applied for entering a 6 digit key for encrypting messages This key has to be identical to a decryption password entered in a server program Pcom Return to primary This option is used when both primary and backup channels are set There must be entered the after duration of time for sending messages though the backup communication channel after losing the primary connection Backup reporting after This option is used when both primary and backup channels are set There must be entered the number of attempts to transmit information through the primary communication channel after which the module will connect to the backup communication channel APN Access point name for connecting to the GSM operator s network User User name for connecting to the GSM network Login Password
18. ich operating parameters of transmitting module should be changed To select right click on the ID number Open the configuration program G10config Left click on the icon G10config has been appeared beside the selected ID number Click on the button Connect in the opened program G10config tool bar GPRS connection status Connected must be indicated in the program s status bar Click the button Read F7 on old configuration to be displayed Further actions are identical as when the module is connected to a computer with a USB cable Just set the desirable values of module operating parameters in the opened program G10config windows After entering desirable values click the button Write F6 on the values to be set in the module G10 Just close the program G10config and GPRS communication session closes too 10 x File Settings About Control y Object state summan Refresh control i Waiting for GPRS 1 w esh io Refresh Options Wasting foe SMS 1 I Relies every 10 seconds pt Simms Le 0 Objects contrat Remove object ObjectID IP Phone number Communication state Level GPRS last ping GPRS pig interwal GSM last ping Gconfig s Ha Wading for GPRS message 3 2010 04 23 151331 50 MZA Firmware version upgrading remotely Connect the module G10 with the program G10config remotely See previous chapter how to connect remotely 1 2 3 4 Open the program G10Oconfig See previous chapter how to o
19. pen the configuration program Press the button Connect To read the parameters set in the module press the button Read Open the window Firmware and with clicking on the button Browse select the latest version of the firmware file Press the button Start Wait until the firmware will be written into the module processor memory This may take 1 3 minutes after which the module will reconnect to the program G10config Set the module operating parameters in the same way as described while connected via USB port 10 Remote PGM output switching In order to change the state of output OUT1 send an SMS message to the SIM card number of the module Examples of SMS messages are provided in the table below Notes Ifthe list Wireless programming phones is empty module will change its output state after receiving an SMS message from any mobile phone If telephone numbers are entered in the list module output state can be changed only from these phones Output state can be changed when output OUT1 operating mode is set to Remote control SMS SMS messages have to be written in capital letters only a PS aaa ra aa aaa aaa a ss Lasa MS MESSAGE TEXT a an Meaning cee See L L I OUTPUT 1234 ON Output state is changedto ON Instead of numbers 1234 enter Your OUTPUT 1234 OFF Output state is changed to OFF Administrator or User code OUTPUT _1234 PULSE 005 Output state is changed to ON for
20. r TRIKDIS U TRIKDIS ZO Network Data A Power A SV00600000 15 GSM module G10 v 1 XX User manual JSC UAB TRIKDIS Draugyst s str 17 LT 51229 Kaunas LITHUANIA E mail info Otrikdis lt Webpage www trikdis lt Contents GSM module GIO aisiais iii a a i i a a i i S i i a a S i a 3 ODS pai alai S 3 OUt dEV EW i a i aa aa Ia i a a a a L aa aa D a 3 AIU O N a e P rr pr EF nates area sata teen dln ee de eat aa E TO desea 4 SCULING OL OBerali DAFAIME les i iii niais i ai a a TN 5 Firmware version UP SPACING iui siai is i an ETT EAT ee 9 Serine Of CONTISUKATION remotely Assisi siai i i i E i e ai 9 Frimware version uperading COT OCC IN maiau ika ai a i i a a a i i a a 10 Ramot POMES0LDUE SW LENS esa aaa Aaa ia ia ai Aa a ia i a a Us a as 11 T eChNLEALSDECIHCA EO ais sai a a i a i a i a a a roe a a 11 Package Content Serasi ai aaa iai i i i i a aa O A a a a a S a othe access 11 ANNEX 1 Non alarm events transmitted to ARC rriari noain aA Aa 12 ANNEX2 Texts of SMS messages which are sent to mobile phone after occurring particular event 12 Safety requirements Please read this manual carefully before using the security module G10 Security module G10 should be installed and maintained by qualified personnel having specific knowledge regarding the functioning of GSM devices and safety requirements The device must be disconnected from external power supply source before starting device installation Mod
21. to receive a SIM card We do not recommend using pay as you go prepaid SIM cards l 3 Fasten the module to the security control panel l The location and dimensions of holes to be drilled in the l metal casing by using either M3x6 screws or casing for fastening the module and antenna adhesive fastening tape _ 4 Screw the GSMantennaon ee ee ee ee ee 5 Connect the module to the security control panel See chapter Wiring diagrams according to wiring diagrams given below PPR 6 Turn on the system power supply p p PPP l 7 Check GSM signal strength according to light Sufficient GSM signal strength is level 5 five yellow flashes of indication indicator Network If GSM signal strength is not sufficient PPR PET EDI TEL ITS ____Useotherantennatype a l 8 Check if the module sends messages according to l The message must be sent and received at the specified IP l its configuration address site If messages are sent to a mobile phone check if L SMS messages are received Wiring diagrams raudonas red KpacHbIA juodas black u pHeiA lt COM lt CLK lt DATA lt IN1 lt OUT lt IN2 lt COM lt MCI geltonas yellow x nTh alias green 3en HHbi RED jimas input Bxog DSC duomen magistral DSC keybus DSC wna AaHHbIX i jimas output Bbixog Wiring diagram to DSC Power Series security control panels PC1616
22. ule G10 should be mounted in places with restricted access and in safe distance from any sensitive electronic equipment The device is not resistant to mechanical effects dampness and hazardous chemical environment Liability restrictions When buying the Device the Buyer agrees that the Device is a part of a security system of premises which sends messages about security system status The Device when installed does not diminish the probability of burglary fire intrusion or other breach of premises UAB TRIKDIS is not responsible for burglary fire or any other breach of Buyer s and or User s premises and is not liable for any direct or indirect damages incurred thereof When buying the Device the Buyer agrees that the Device supplied by UAB TRIKDIS fully meets his requirements for intended use UAB TRIKIDIS provides no guarantees that the Device shall function as declared if the Device is installed and used not according to its original purpose user manual and relevant electronic and technical conditions UAB TRIKDIS is in no way associated with GSM GPRS Internet service providers operators thus UAB TRIKDIS is in no way responsible for any defects in Device operation if they have occurred because of the loss of GSM GPRS Internet connection or because of other defects in the service provider network UAB TRIKDIS has no control and is not responsible for the prices and marketing of network
Download Pdf Manuals
Related Search