E-KB04 User Manual
Contents
1. the suppliers Press ENTER SET CAM PROTOCOL gt Select all control protocols of camera ALE FE enter lt Press CLR Select the required protocol of camera Rotate the joystick to select the required protocol and input address No by digit key After selection of the protocol press ENTER to make acknowledgement or press CLR to exit the setting 5 SET KEY ID Set up the ID of the controller from 01 to 63 SEI KIDY MD Input to ID by digit key After setting press ENTER to make acknowledgement or press CLR to exit the setting 01 lt 01 63 gt 6 SET KEY LEVEL Set up the control levels of the controller from 00 to 15 Input level No by digit key Note the lower No is the higher level After setting press ENTER to make acknowledgement SET LIEN Ee or press CLR to exit the setting 01 lt 00 15 gt 7 SET MON RANGE Set up the range of monitors from 0000 to 0239 Input monitor No by digit key After setting press ENTER to make acknowledgement or press CLR to exit the setting SET MON a 0000 0239 E KBOA Kevboard Controller SET CAM RANGE 8 SET CAM RANGE Set up the range of the intelligent dome cameras from 0000 to 9999 Input camera No by digit key After setting press ENTER to make acknowledgement or press CLR to exit the setting 0000 9999 9 SETALM RANGE Set up the range of alarm positions from 0000 to 9999 SET ALM RANGE Input alarm No by digit key After setting press ENTER to make acknowledg2. 0 OFF SET Clear Seq Stack 21 SHOT SET Show Seq Stack 22 SET N SET Sequence dwell time N 0 255 23jje ON N OFF Home function 24 SET N AUTOPAN AUTO_PANING SPEED N 0 255 25 ON N AUTOPAN AUTO_PANING LIMIT ILEFT 2RIGHT 26 AUTOPAN AUTO_PANING START E KB04 Keyboard Controller 27 SET AUTOPAN N ENTER SET TILT SPEED N 0 255 SET PAN SPEED N 0 255 28 SET SET AUTOPAN N ENTER MUST SET PAN_SPEED FIRST THEN TILT_SPEED 29 CAM ON CAMERA ON 30 CAM OFF CAMERA OFF 31 ON AUTOPAN AUTO SCAN 32 OFF AUTOPAN MANUAL SCAN NOTE 1 One who has authority of management can set up 2 The protocol of non original Pelco products is not as same as above protocol Please refer to the dome camera manual E KB04 Keyboard Controller Description of Operating Keys for DVR of Keys of the controller Usage Display CLOSE DEL Delete DEL ALM Record RECORD ON Play PLAYBACK SET Set up SETUP SHOT Back up BACKUP NEAR Format PIC_FORMAT 1 1 D1 2 2 D2 3 3 D3 4 4 D4 5 5 D5 6 6 D6 7 7 D7 8 8 D8 9 9 D9 0 0 DO FAR Switching PIC_LOOP MON Chinese CHINA CAM point POINT WIDE PgUp Previous page PAGEUP TELE PgDn Next page PAGEDOWN Joystick UP Up UP Joystick DOWN Down DOWN Joystick LEFT Left LEFT Joystick RIGHT Right RIGHT OPEN BACK Return BACK ENTER Acknowledgment ENTER AUX Frame progress FRAME OFF Fas
3. 1 One who has authority of management can set up 2 The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with Camera 20
4. D OFF E KB04 Keyboard Controller DSF 9 ON SET AREA TITLE NESW ON 30 9 ON_SHOT AREA TITLE USER ON AREA TITLE 31 9 OFF AREA TITLE OFF SD 10 ON EL ZOOM ON EL ZOOM 33 10 OFF EL ZOOM OFF 34 11 ON REFRESH REFRESH PRESET1 SET PRESET2 SET B55 SET N ENTER PRESET STORE PRESET63 SET PRESET64 SET 36 12 ON PATROL PLAY 37 12 OFF PATROL STOP PATROL 38 12 SET PATROL LEARN 39 OPEN IRIS OPEN IRIS 40 CLOSE IRIS CLOSE 41 IRIS FREE IRIS STOP 42 O IRIS IRIS RESET 43 13 ON SHUTTER ON SHUTTER 44 13 OFF SHUTTER OFF 45 13 TELE SHUTTER INC 46 13 WIDE SHUTTER DEC 47 14 ON AGC ON AGC 48 14 OFF AGC OFF 49 15 ON SENS UP FIX ON 507 15 OFF SENS UP FIX OFF SENS UP FIX Sil 15 TELE SENS UP FIX INC DD 15 WIDE SENS UP FIX DEC aa 16 ON SENS UP AUTO ON 54 16 OFF SENS UP AUTO OFF SENS UP AUTO say 16 TELE SENS UP AUTO INC 56 16 WIDE SENS UP AUTO DEC Sif 17 TELE LL Phase INC LL phase 58 17 WIDE LL Phase DEC 180 d t 594 18 ON 180 deg pan turn Sia wean 60 19 ON CLEANING ON MENU CLEANING 61 19 OFF CLEANING OFF MENU RECEIVER 62 0 AUX ON AUX ALL ON FUNCTION COMMAN 63 0 AUX OFF AUX ALL OFF E KB04 Keyboard Controller 64 1 AUX ON AUX 1 ON 65 1 AUX OFF AUX 1 OFF 66 2 AUX ON AUX 2 ON 67 2 AUX OFF AU
5. D RAWE 9600bps 2 SET MUX PROTOCOL Select the relative protocol for the current multiplexer so as to control the multiplexer Protocols of ROBOT have been set up ex works Default protocol is ROBOT Any other protocol of MULTIPLEX is required please contact the suppliers Select the protocol by rotating the joystick After selection of protocol press ENTER to make acknowledgement or press CLR to exit the setting SET MUX PROTOCOL ROBOT 3 SET DVR Select the protocol for the current DVR so as to control the DVR Protocols of HIK have been set up ex works Default protocol is HIK Any other protocol of DVR is required please contact the suppliers Press ENTER b SET DVR Select all control protocols of DVR 4 ALL HIK Press CLR Select the required protocol of DVR Rotate the joystick Press ENTER ID No of DVR SET DVR p Press CLR ID 01 OUT 0001 Input No to matrix system from DVR Camera No corresponded with input No to DVR Input No of DVR E KB04 Keyboard Controller Note Rotate the joystick to select the required protocol and input address No by digit key After selection of the protocol press ENTER to make acknowledgement or press CLR to exit the setting 4 SET CAM PROTOCOL Select protocol for the cameras Protocols of Pelco D Pelco P Panasonic Samsung DM have been set up ex works Default protocol is Any other protocol of camera is required please contact
6. E KBOA Kevboard Controller E KBO4 User Manual e Matrix switcher Q Intelligent high speed dome camera e DVR Press DVR and enter DVR mode default Open In 3 seconds protocol HIK 1 Press MENU and enter xeeeX VERO lt 01 gt MON gt CAMA Can directly control Multiplexer Press MUX and enter MULTIPLEX management system operation 001 0001 follows make of ROBOT System Keyboard os gt 2 Press ON 2 under the management system and apply for levels of authorized user Q Matrix switcher The initial password is 9876543210 and CAM ALM Can directly control Q Intelligent high speed dome camera PASSWORD press ENTER to make acknowledgement 0001 0001 ee Protocol is set up for ex works VEEL ELE EEL 3 DVR Press DVR and enter DVR mode gt p gt default protocol HIK Q Multiplexer Press MUX and enter MULTIPLEX made of ROBOT SET BAUD RATE SET KEY LEVEL 3 Press MENU and enter menu SET MUX PROTOCOL SET MON RANGE operation operate joystick up and SET DVR SETCAM RANGE down for the menu gt SET CAM PROTOCOL SET ALM RANGE Illustration as follows SET KEY ID RESET DEFAULT_I E KBOA Kevboard Controller Simplified Description of Menu 1 SET BAUD RATE Set up baud rate of communication Baud rate of 960OBPS has been setup ex works After selection of band rate press ENTER to make acknowledgement or press CLR to exit the setting SET BAU
7. ET N NEAR ENTER Set Near Speed N 1 9 24 SET N FAR ENTER Set Far Speed N 1 9 25 SET N TELE ENTER Set Tele Speed N 1 9 26 SET N WIDE ENTER Set Wide Speed N 1 9 NOTE 1 One who has authority of management can set up 2 The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with Camera E KB04 Keyboard Controller Description of Operating Keys for Pelco p amp Pelco d No Keys of the controller Usage 1 SET N ENTER Set Preset 2 CLR N ENTER Clear Preset Go To Preset N 32 PRESET N 33 Flip 180 about N 34 Go To Zero Pan N 92 Set Left Limit Stop N 93 Set Right Limit Stop 3 SHOT N ENTER N 94 Remote Reset N 95 Enter Menu Mode N 96 Stop Scan N 97 Begin Random Scan N 98 Begin Frame Scan N 99 Begin Auto scan 4 N ON Set Auxiliary 5 N OFF Clear Auxiliary 6 SET CLR ENTER Remote Reset 7 SET N ON Set Zone Start 8 SET N OFF Set Zone End 9 CLR OFF Clear Screen 10 AUX HON Zone Scan On 11 AUX OFF Zone Scan Off 12 SET ON Set Pattern Start 13 SET OFF Set Pattern Stop 14 CAM RUN Run Pattern 15 SET N ZOOM Set Zoom Speed N 0 3 16 SET N FOCUS Set Focus Speed N 0 3 17 SET RUN Start Sequence Prepos 18 ON N SET Insert Prepos In Stack 19 CLEAR N SET Delete Prepos From Stack 2
8. ST 11 SET N WIDE ENTER SET ZOOM SPEED 0 SLOW 3 FAST 12 SET N CLOSE ENTER SET PAN SPEED 0 15 27 SET N OPEN ENTER SET TILT SPEED 0 15 28 ON OPEN AUTO IRIS 29 ON FAR AUTO FOCUS KEY_ON 30 OFF FAR AUTO FOCUS KEY_OFF 31 SHOT FAR AUTO FOCUS_FROM_TABLE 32 CAM ON CAM ID DISPLAY_ON 33 CAM OFF CAM ID DISPLAV OFF 34 CAM SET ON CAM TITLE DISPLAY_ON 35 CAM SET OFF CAM TITLE DISPLAY_OFF 36 OFF WIDE DIGITAL ZOOM OFF 37 ON N WIDE DIGITAL ZOOM ON 2 8 38 AUTOPAN N SET AUTO_FLIP ON OFF 1 0ON 0 OFF 39 SET MON CLEAR REMOTE RESET 40 SHOT ENTER GOTO HOME POSITION 41 SET N SHOT SET PRESET N TO HOME POSITON 0 127 42 SETENESET LINE LOCK TIMING ADJUSTMENT O INCREASE 1 DECREASE 43 SHOT N ALM GOTO ALARM POINT 44 N ON ALM SET ALM PRESET REMAIN_TimeN 1 255 E KB04 Keyboard Controller 45 N OFF ALM SET ALM PRESET RELEASE TimeN 1 255 46 N ON AUX SET AUX NON N 0 7 47 N OFF AUX SET AUX N OFF N 0 7 48 ETLAJTOBANENEON SET START END POINT FOR AUTOPAN 0 1 START END SET ROTATIONAL DIRECTION FOR 49 N SET AUTOAN AUTOPAN 0 RIGHT left 50 SET N AUTOPAN SET SPEED FOR AUTOPAN SPEED N 0 3 51 ON N CAM HOME FUNCTION ON DELAY_ND 1 127 MINUTES 52 OFF N CAM HOME FUNCTION OFF DELAY_ND 1 127 MINUTES ENTER MENU N N 1 1 Fill Preset into Sequence 2 Set Sequence Dwell time 53 SET CAM N ENTER 3 Set Sequence Speed N 2 Set Alarm Point N 3 Set OSD Camera NOTE
9. X 2 OFF 68 1 AUX SHOT AUX 1 MOMENTARY 69 1 AUX SET AUX LATCH 70 2 AUX SHOT AUX 2 MOMENTARY rales 2 AUX SET AUX 2 LATCH 12 CAM SET SETUP MENU ON TE CAM CLR SETUP MENU OFF 748 0 SET SETUP MENU Cursor STOP US JOYSTICK_UP SETUP MENU Cursor UP 76 JOYSTICK_RIGHT SETUP MENU Cursor Right Vik JOYSTICK_DOWN SETUP MENU Cursor Down 78 JOYSTICK_LEFT SETUP MENU Cursor Left MENU os ENTER SETUP MENU SETI 80 CLR SETUP MENU SET2 81 1 CAM SET SETUP MENU SW RESET 82 0 CAM SET SETUP MENU SW ALL RESET 83 0 CAM ON Menu ON 84 0 CAM OFF Menu OFF NOTE 1 One who has authority of management can set up 97 2 The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with Camera E KB04 Keyboard Controller Description of Operating Keys for Intelligent Dome Camera of Dyna Color No Keys of the controller Usage 1 SET N ENTER SET PRESET N 0 127 2 CLEAR N ENTER CLEAR PRESET N 0 127 3 SHOT N ENTER GO TO PRESET N 0 127 4 AUTOPAN N ON RUN SEQUENCEN 0 7 5 N AUTOPAN RUN CRUISE O autopan cruise 6 SHOT N SHOT GOTO PRESET N WITH MAXSPEED 0 127 7 AUTOPAN CLEAR TOUR STOP STOP PAN TILT ZOOM IRIS 8 SET N AUX SET CRUISE MEMORIZE 0 START 1 STOP 9 SET N RUN SET JOYSTICK CONTROL MODE 1 ON 0 OFF 10 SET N FAR ENTER SET FOCUS SPEED 0 SLOW 3 FA
10. _DELETE N 0 127 25 1 FAR ONE FAR NOTE 1 One who has authority of management can set up 2 The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with Camera E KB04 Keyboard Controller Description of Operating Keys for Intelligent Dome Camera of PANASONIC Keys of the i NO Usage Function controller PRESET 1 CALL PRESET 2 CALL 1 SHOT N ENTER PRESET CALL PRESET 63 CALL PRESET 64 CALL 2 ON AUTOPAN AUTO PAN ON 3 OFF AUTOPAN AUTO PAN OFF 4 1 AUTOPAN AUTO PAN SPEED INC z AUTO PAN a 2 AUTOPAN AUTO PAN SPEED DEC 6 3 AUTOPAN AUTO PAN START POINT SET Je 4 AUTOPAN AUTO PAN END POINT SET 8 5 AUTOPAN AUTO MODE OFF 9 6 AUTOPAN AUTO SEQ ON AUTO MODE 10 7 AUTOPAN AUTO SORT ON 11 8 AUTOPAN AUTO PAN SWEEP AREA INVERT 125 1 ON ENDLESS ON ENDLESS lB 1 OFF ENDLESS OFF 14 2 ON DIGITAL FLIP ON DIGITAL FLIP ISi 2 OFF DIGITAL FLIP OFF 16 3 ON PROPORTIONAL P T ON PROPO P T yee 3 OFF PROPORTIONAL P T OFF 18 4 ON SUPER DII ON SUPER DII 19 4 OFF SUPER DII OFF 20 5 ON STOP AF ON MENUITEM AF Dale 5 OFF STOP AF OFF MENUITEM De 5 SHOT 1 SHOTAF ON START PAS 6 ON HOME POSITION MOVE HOME POSITION 24 7 ON BW ON MENU ITEM Daye 7 OFF BW OFF MENU ITEM BW 26 7 SET BW AUTO MENUITEM PIS 8 ON CAMERAID ON CAMERA ID 28 8 OFF CAMERAI
11. ement or press CLR to exit the setting 0000 9999 10 RESET DEFAULT 17 Select the default code The default code is 0123456789 ex works Input the default No by digit key After setting press ENTER to make acknowledgement or press CLR to exit the setting RESET DEFAULT_I Input the default No by digit key from0 to 9 press RESET DEFAULT_I SE a a CR KK ENTER gt PLEASE WAIT oo NOTE After setting and save the controller is available Only the band rate of communication needs restarting Others need not restart E KBOA Kevboard Controller Simplified Description of Setting and Operation for DVR on the Controller 1 Press DVR to switch DVR s operating surface or front end camera control surface ID of DVR Select input channel No of DVR Press DVR for one time Press DVR for one time MON gt CAMA ALM ttqt t b DVR ID 01 DVR_ID 01 IN 01 001 0001 0001 4 Camera No corresponds to input Press MENU Press DVR channel No of DVR 2 Under the state of DVR press NEXT to select ID of the current DVR One who has authority of management can setup input channel No of DVR corresponding to camera No Setting is also available in main menu ID of DVR Press NEXT by one who has Select input channel No of DVR Press NEXT for one time authority of management w w p DVR ID 01 Set DVR ID ID 01 OUT 0001 t Mm _ A Camera No corresponds to inp
12. isplay UP Up UP DOWN Down DOWN LEFT Decrease DEC RIGHT Increase INC ENTER Acknowledgement ENTER CLEAR Exit EXIT SET Menu MENU RUN Picture in picture PIP MON Call back CALL NEXT Switching SEQ CLOSE Play PLAY TELE Zoom ZOOM HOLD Frozen FROZEN OPEN 2 2 2 2 FAR 3 3 3 3 WIDE 4 4 4 4 1 1 1 2 2 2 9 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 11 11 11 12 12 12 13 13 13 14 14 14 15 15 15 16 16 16 i Chooses digit NOTE 1 Under the mode of multiplexer there are 16 frames of pictures Press to select unit frame Press to select Two digits frames 2 The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with relevant device E KB04 Keyboard Controller Description of Operating Keys for Intelligent Dome Camera of SAMSUNG No Keys of the controller Usage 1 0 ENTER KO 2 1 ENTER KI 3 2 ENTER K_2 4 3 ENTER K_3 5 4 ENTER K_4 6 5 ENTER K_5 7 6 ENTER K_6 8 7 ENTER K_7 9 8 ENTER K_8 10 9 ENTER K_9 11 ON GRP SCAN_START 12 OFF GRP SCAN_STOP 13 ON SET MENU_ON 14 OFF SET MENU_OFF 15 ENTER ENTER 16 SHOT N ENTER PRESET_MOVE N 0 127 17 ON AUTOPAN AUTOPAN_START 18 OFF AUTOPAN AUTOPAN_STOP 19 ON N AUX PATTERN_START N 0 3 20 OFF N AUX PATTERN_STOP N 0 3 21 0 CLEAR SET RESET 22 100 CLEAR SET FACTORY_RESET 23 SET N ENTER PRESET_SAVE N 0 127 24 CLEAR N ENTER PRESET
13. lexer s ID of protocol and baud rate of communication E KBOA Kevboard Controller Simplified Description of Inquiry of Setting State and Relevant Hardware of the Controller Under the state of non setting press SHOT CAM to display the current camera s ID of protocol and band rate of communication Press any key to exit Current Cam 0001 a 9600b Description of indicator Red POWER Power indicator Green SYS System state indicator o Communication receiving Yellow DVR DVR indicator Green Rx ia indicator PA Communication emission Green MUX Multiplexer indicator Green Tx te indicator Under working state of the controller the power indicator lights When communication signal is received green Rx indicator will be glittering When communication signal is emitted green Tx indicator will be glittering If DVR Multiplexer and system are working the relevant indicators light The movement up down left right of the joystick can control the relevant action of the cameras Rotate the joystick to control the zoom of lens Camera protocol and band rate are arranged in pairs as follows Details see the relevant of camera manual Pelco P 2400bps 4800bps 9600bps 19200bps 2400bps 4800bps 9600bps 19200bp Pelco D oe 9600bps Panasonic 9600bps Samsung _ 9600bps E KB04 Keyboard Controller Description of Operati
14. nly operation of the controller Detail functions please refer to the manual Attached with Matrix E KB04 Keyboard Controller Description of Operation Keys of the Controller for Camera for User No Keys of the controller Usage 1 SET N ENTER Set preset N 2 SHOT N ENTER Go To Preset N N 0 Start Sequence Prepos 3 SET N 0ON Insert Prepos In Stack Delete Prepos From Stack 4 SET N OFF N 0 Delete all Prepos From Stack De SET N SET Set Stack Dwell time 6 SET ON Set up AUTO_PANING Start LIMIT Wye SET OFF Set up AUTO_PANING End LIMIT 8 SET N SHOT Set up speed of AUTO_PANING N 1 9 9 AUTOPAN Run AUTOPAN 10 ON CAM ENTER Unlock current camera 11 OFF CAM ENTER Lock current camera 12 ON CAM N ENTER Open CAM Auxiliary 13 OFF CAM N ENTER Close CAM Auxiliary N 0 Set up Dismantle terminal alarm For N 1 8 Open Close auxiliary Switch 12 amp 13 N 9 Auto Manual Focus N 10 Auto Manual Iris 14 CAM MENU Enter Camera Menu 15 CLOSE N simultaneously CLOSE Speed N N 1 9 16 OPEN N simultaneously OPEN Speed N N 1 9 17 NEAR4N simultaneously NEAR Speed N N 1 9 18 FAR N simultaneously FAR Speed N N 1 9 19 TELE N simultaneously TELE Speed N N 1 9 20 WIDE N simultaneously WIDE Speed N N 1 9 21 SET N CLOSE ENTER Set Close Speed N 1 9 22 SET N OPEN ENTER Set Open Speed N 1 9 23 S
15. on Keys of the Controller for Matrix for User No Keys of the controller Usage 1 MON N ENTER Select monitor N 0 239 2 CAM N ENTER Select camera N 0 Set up defence of current alarm Bi ON MON N ENTER N 1 Date amp Time Display_On N 2 Address Info Display_On N 0 Dismantle defence of current alarm 4 OFF MON N ENTER N 1 Date amp Time Display_Off N 2 Address Info Display_Off Access switching mode N 1 128 Program Mode 5 GRP N ENTER N 129 Sequence_Mode N 130 BackWard_Mode N 131 134 Group_Mode 6 CAM N ON Insert camera in auto switching 7 CAM N OFF Delete camera in auto switching 8 MON N RUN Set up the dwell time of auto switching 9 RUN Run auto switching 10 HOLD Hold auto switching 11 PREV Manual previous switching 12 NEXT Manual next switching 13 ALM N ON Set up defence of alarm 14 ALM N OFF Dismantle defence of alarm 15 ALM N ENTER Query alarm status 16 AUX N 0ON Open auxiliary relay 1A AUX N OFF Close auxiliary relay 18 AUX MON OFF Lock current monitor 19 AUX MON ON Unlock current monitor 20 ON N ENTER Close Relay No n 20 OFF N ENTER Open Relay No n 22 STAR Reply alarm info etc 23 SHOT MON N ENTER Access switching mode 24 MON MENU Enter Menu 25 MON ENTER Enter Sub Menu NOTE 1 One who has authority of management can set up 2 The above mentioned is o
16. t forward FORWARD GRP Fast reword BACKWARD AUTOPAN Pause PAUSE CLR Alarm clear ALARM CLEAR 7 Information INFO HOLD lock LOCK NOTE The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with relevant device E KB04 Keyboard Controller Description of Operating Keys for DVR of HIK Keys of the controller Usage Display Joystick UP Up UP Joystick DOWN Down DOWN Joystick LEFT Left LEFT Joystick RIGHT Right RIGHT 0 1 1 1 0 2 2 2 0 3 3 3 0 4 4 4 0 5 5 5 0 6 6 6 0 7 7 7 0 8 8 8 0 9 9 9 1 0 10 10 1 1 11 11 1 2 12 12 1 3 12 13 1 4 14 14 1 5 15 15 1 6 16 16 AUTOPAN Editing EDIT PREV Multiples display VIEW AUX Display channels of camera A inputs of DVR ON Play PLAY ALM Record REC CAM P T control PAN SET System menu MENU Joystick UP i UP Alter setting Joystick DOWN DOWN Joystick LEFT L L LEFT Select items of setting Joystick RIGHT RIGHT ENTER Acknowledgement ENTER CLEAR Exit ESC NOTE The above mentioned is only operation of the controller Detail functions please refer to the manual Attached with relevant device E KB04 Keyboard Controller Description of Operating Keys for Multiplexer of ROBOT Keys of the controller Usage D
17. ut Press CLR Press CLR channel No of DVR Input channel No of DVR 3 Under the state of DVR press RUN to display the DVR s ID of control protocol and baud rate of communication Press RUN tj DVR_ID 01 Current DVRID 01 cM Press any key MOKMhne E KBOA Kevboard Controller Simplified Description of Setting and Operation for Multiplexer on the Controller 1 Press MUX to switch Multiplexer s operating surface or front end camera control surface Press MUX for one time MON gt CAM ALMA j 001 0001 0001 4 Press MENU 2 Multiplexer corresponding to camera No Press AUTOPAN for one time p MUX ID 01 t Press CLR 3 Press AUX MUX ID 01 4 Press anv kev MUX ID 01 Set DVR ID Current ROBOT MUX ID 01 9600bps ID of DVR Select input channel No of DVR Press MUX for one time gt MUX_ID 01 IN 01 4 Camera No corresponds to input Press MUX channel No of DVR Under the state of Multiplexer press NEXT to select ID of the current Multiplexer One who has authority of management can setup input channel No of ID of DVR Press AUTOPAN by one who Select input channel No of DVR has authority of management ID 01 OUT 0001 1 Press CLR Camera No corresponds to input channel No of DVR Input channel No of DVR Under the state of Multiplexer press AUX to display the Multip
Download Pdf Manuals
Related Search