CP-UM-5290E - Azbil Corporation
Contents
1. e sssssesessssosssssssossssssosessssossesesos 4 5 E How to operate the numeric monitor screen esssesssseseeseccee 4 5 E How to operate the trend monitor sssssssssessssssssssesoseee 4 7 TROUBLESHOOTING Error Messages and Remedy essesssessosssessossesssossosssessoee 5 1 E Communications error MESSAGES ee eee eee eee reece eect cere neces 5 1 E File error M SSAGES 1 cece cece cece cer c eee eesceecccesesseeeseeees 5 1 Other Troubleshooting sssssessesssssssssssssosesssosssossosssos 5 2 Conventions Used in This Manual The following conventions are used in this manual CJ Handling Precautions A Note i gt 1 2 3 OK button Option gt gt Ctrl key A key Ctrl A key Handling Precautions indicate items that the user should pay attention to when handling the SLP C35PRO Notes indicate useful information that the user might benefit by knowing This indicates the item or page that the user is requested to refer to The numbers with the parenthesis indicate steps in a Sequence or indicate corresponding parts in an explanation Indicates a selection button in screens displayed on the personal computer Indicates messages and menus displayed on the personal computer Indicates the result of an operation details displayed on the personal computer or devices or the state of a device after an operation Indicates keys on the keyb2. Revision History date Oct 2005 CP UMS200E tstEaition OOO O O June 2008 References to serial port deleted Vista operating system added BiInstalling the software deleted and section heading 2 1 Installing the loader added Section 2 2 Device Driver Installation for USB Loader Cable added Section 2 3 Starting and quitting the loader added Starting the program and Quitting the program sections moved here from page 2 5 Recent files submenu added to File menu Submenu details added to CSV Out and HTML Out submenus azbil Yam at ake Corporation Specifications are subject to change without notice 08 Advanced Automation Company 1 12 2 Kawana Fujisawa Kanagawa 251 8522 Japan URL http www azbil com 1st Edition Issued in Oct 2005 E 2nd Edition Issued in June 2008 W
3. E File error messages File name This filename is not valid An invalid file name is input Input a correct file name error This file cannot be found A file name not existing is input Input an existing file name Make sure that the correct path and filename are given This filename is a reserved A file name reserved for the device Input a correct file name device name name is input Use a different filename Disk error Not enough free space on disk The disk free capacity is insufficient Keep a sufficient disk free capacity The device is not ready The disk is not ready Prepare the disk and restart the operation Cannot make file The CD ROM is specified as save Save the file to another directory destination File name too long The file name is too long Use 256 characters or less for the file name Pass name The path does not exist An illegal path name is input Input a correct path name and error Make sure that the correct path is restart the operation given File information Illegal file size The file is corrupted Corrupted file cannot be used error Illegal file information Create a file again Chapter 5 TROUBLESHOOTING 5 2 Other Troubleshooting Numeric values are not displayed lf a decimal point symbol other than period Check that the decimal point symbol correctly is set the loader does not function correctly is period If not set the decimal point symbol to period
4. OPort COMB OPort CON14 a O OPort COM OPort COMI5 l 11 or or EA OPort COM8 Port CONI6 a O12 Transmission speed Data Length rParity Stop bits Fixed Cell Width g 2 Select the desired communications port 3 Select the desired font size 4 Click the OK button J Handling Precautions e Normally use Port COM1 Even if another communications port can be selected it sometimes cannot be used depending on its characteristics e Normally select Use Loader Cable Step 4 Set up the SDC15 25 26 35 36 parameters Move the cursor to the target channel for each setup item and do the following e When the setting is a numerical value Enter the numerical value and press the Return key e When the setting is selected by a number Press the right mouse button right click on a setup item The list of settings you can select will appear Select a desired item to complete the setting Set each of the parameters required for running the SDC15 25 26 35 36 The following two types of parameters are set e Basic functions Basic functions for device operation such as control and communications functions e Optional functions Includes user defined functions DO assignment and extended tuning Chapter 3 SETUP n Handling Precautions e is displayed within the cell if setup of a parameter is not required or is prohibited by previous settings The parameter cannot be set If neccessary re check the type
5. e Make sure that the Decimal symbol has been set to for Control Panel Regional Settings Number If it has been set to some other character the loader program cannot function correctly Chapter 1 INTRODUCTION E Hardware configuration General configuration SLP C35 SDC15 25 26 35 36 ow ss SSS SSS SSS SS LLI IAL Configuration with CMC10B L e When connecting 31 units or less CMC10L Com Ca aa Ran OAR ARo CERI CLEIT RIIN IIIT LLII IS 7 o gt COS Max 31 units e When connecting 32 units or more CMC10L_CMC10B CMC10B CMC10B LY LOON ROARK OR CY 2 RRRA a LIRI ITR T IIIS LOEES gt Max 31 units Max 31 units Max 31 units Note e The CMC10B allows up to 31 units to be connected to a host device Note e Personal computer used for confirmation of operating environment Dell OptiPlex GX110 Think Pad A31 1 3 Chapter 2 INSTALLATION STARTING AND QUITTING 2 1 Installing the Loader This section describes how to install the SLP C35 on a personal computer J Handling Precautions e f you start the installer while another application is running the installer may malfunction Shut down other applications and then start the installer The SLP C35 sometimes cannot be started due to a particular combination of other applications and drivers For details on Windows and personal c
6. x Fress OK to remove driver Cancel 2 Click the OK button gt gt The following window appears Warning If you want to install new driver you must re boot Windows system now Will you re boot Windows system immediately 3 To complete the removal of the driver the computer must be restarted Click the Yes button to restart the computer Chapter 2 INSTALLATION STARTING AND QUITTING 2 3 Starting and Quitting the Loader E Starting the loader E Quitting the loader 2 12 Double click the SLP C35 SDC15 25 26 35 36 icon on the desktop or click the Start button at the lower left portion of the screen and select Programs SLP gt SLP C35 gt gt The Smart Loader starts up and the menu window is displayed Note e For operating system details and mouse setup refer to the user s manuals provided with Windows Click the icon at the top right of the screen or selecting Menu Quit gives the same result Chapter 3 SETUP 3 1 Setup Function E Overview The setup function allows the user to set various parameters from 10 to 70 constants required for operation and write these parameters to the SDC15 25 26 35 36 so that it functions according to the user s particular control requirements When the SDC15 25 26 35 36 is used for the first time it will not function as required unless it is set up by using this setup function Parameters such as SP set point and cont
7. 5 2 INTRODUCTION OVVIO W os a6 4 6 6 er ne a ae EEr EN EA 1 1 E Program functions ccc cece cece esc e rr ceee essere eeceseesseeeeeens 1 1 System Requirements sessesssessossssssossosssossosesesossssesso 1 2 E HardWal Cs os 6 eo rainen 65h N EErEE NENE 1 2 M Hardware configuration e essssssssesesscossecsessosesecesseoe 1 3 INSTALLATION STARTING AND QUITTING Installing the Loader esssseesesessssosssoesesossesesesossesoen 2 1 Device Driver Installation for USB Loader Cable sessssssssseess 2 6 E Installing the device Criver eee cece cece cece cece eee eeeeeeeeees 2 6 E Uninstalling the device driver ceeeeeece cece cece eeeeeees 2 11 Starting and Quitting the Loader ceeceeceeeceeeeeeceeeeeeees 2 12 M Starting the loader esssessessssssossosssesssesosssosssessos 2 12 E Quitting the lOadel is sc6cct er ieshe cect ccnnessteseetieeteiedicgortes 2 12 SETUP S tup FUNGON reriosssaranirsaedinri do nre knea N E EENE AE 3 1 OO aa os hs E E E E E E E EE E E E E ead 3 1 M Screen explanations sessssossessssssosesosesossssocsesosssoos 3 1 Method of Setup ess ss sesssssssosossssssessssssooosoessssscsssesooooo 3 4 MONITORING Monitoring Function se ssessssessssesssoesesossosesesoesssessooeseoo 4 1 E a E E 6555 E EEE E E E E E E E E ORS 4 1 M Screen explanations s ssesssssssssssssecssesosesosseseseseseesess 4 2 Method of Operation
8. AUTO 1 MANUAL 4 5 Chapter 4 MONITORING Changing of data Operation by entry of numerical values Enter the numerical value and press the Return key Setting of user defined address Optional data not in the table can be registered to user configuration address UF 1 to 8 in the table Data can be read or written according to the data type e How to set user defined address 1 Select the Set monitor tag under Option O Setup in the pull down menu 2 Enter the address of the data to display according to SDC15 Single Loop Controller User s Manual Installation amp Configurations CP SP 1148E SDC25 26 Single Loop Controller User s Manual Installation amp Configurations CP SP 1149E and SDC35 36 Single Loop Controller User s Manual Installation amp Configurations CP SP 1150E Use of the command line Data can be read or written or the mode switched by directly entering communications commands on the command line B Handling Precautions e Transmission of the wrong command may result in trouble on the SDC15 25 26 35 36 For this reason take sufficient care when describing command types addresses data and other information e For details on communications commands and data addresses refer to gt SDC15 Single Loop Controller User s Manual Installation amp Configurations CP SP 1148E SDC25 26 Single Loop Controller User s Manual Installation amp Configurations CP SP 1149E SDC35 36 Sing
9. color Clicking Default will return the color setting to its initial value 5 x Color Basic colors EE 8 6 169 Define Custom Colors gt gt Cancel Chapter 4 MONITORING e Setting up the trend trigger File Numeric Monitor Trend Monitor Trend Monitorfindividual Digital Trend Monitor Trend Monitor Color Trend trigger On trigger Off trigger Save trigger O None 25 DM REV O None 25 DN REV O None 25 DN REV 4 Di 26 DI2 REV 4 Di C 26 DI2 REV CEDI 26 DI2 REV 2DI2 C 27 DIB REV 2di2 C 27 DIB REV C 2Di2 27 DIB REV 3 13 C 28 DI4 REV 3 Di3 C 28 DI4 REV 3 Di3 C 28 DI4 REV C 4 Dl4 C 29 EV1 REV C 4Dl4 C 29 EV1 REV C 4014 C 29 EV1 REV C S amp v41 C 30 EV2 REV C SEVI C 30 EV2 REV C S5EVY1 30 EV2 REV C BEV2 C 31 EV3 REV C amp EV2 C 31 EV3 REV C amp EV2 C 31 EV3 REV C 7EV3 C 32 DM REV C TEV3 C 321 DM REY C TEV3 C 321 DM REY C 8 D1 33 1 DI2 REV 8 D1 C 33 1 DI2 REV C 8 D1 33 1 DI2 REV C 9 DI2 34 1 DIS REV C 9 I DI2 C 34 1 DIS REV C 9 1 Di2 34 1 DIS REV 10 1 DI3 C 35 DI4 REV 10 1 DI3 C 35 1 DI4 REV 10 1 DI3 C 35 DI4 REV 11 1 D14 36 1 DIS REY C 411 1 Di4 C 36 DIS REV 411 1 DI4 C 36 DIS REV C 121 DI5 C 37 LEV1 REV 121 DI5 C 37 EV1 REV C 121 DI5 C 37 LEV1 REV 413 E 41 33 EV2 REV CANSEI C 33 EV2 REV C 13 l EV1 C 33 EV2 REV 1
10. loader jack on the front panel This function is used when the user adjusts controller input For details on the adjustment function refer to gt SDC15 Single Loop Controller User s Manual Installation amp Configurations CP SP 1148E SDC25 26 Single Loop Controller User s Manual Installation amp Configurations CP SP 1149E SDC35 36 Single Loop Controller User s Manual Installation amp Configurations CP SP 1150E o Handling Precautions e When the adjustment function is used previous adjustment values stored on the controller are discarded When this function is used for the first time the controller s default adjustment values are discarded Beware of this when using this function 1 1 Chapter 1 INTRODUCTION 1 2 System Requirements The following operating environment is required for using the SLP C35 E Hardware Personal Computer Processor PC AT compatibles with a Pentium chip or higher 32MB or more Operating system Windows98 Me 2000 Professional XP Vista Peripheral Devices 800 X 600 dot or more 16 bit color or more Hard disk drive Hard disk with at least 40MB of free space Pointing device Windows compatible mouse or equivalent device L Handling Precautions e Before starting the Smart Loader quit all other applications The program may not function if you start it while another application is running Set the power save setting infrared communications and screen saver to OFF
11. might cause communications failure If this happens reconnect the loader plug correctly NOTICE Be sure that the user receives this manual before the product is used Copying or duplicating this users manual in part or in whole is forbid den The information and specifications in this manual are subject to change without notice Considerable effort has been made to ensure that this manual is free from inaccuracies and omissions If you should find an error or omis sion please contact Yamatake Corporation In no event is Yamatake Corporation liable to anyone for any indirect special or consequential damages as a result of using this product 2005 Yamatake Corporation ALL RIGHTS RESERVED Unpacking Check the following items when removing the SLP C35 from its package 1 Check the model No to make sure that you have received the product that you ordered 2 Check the SLP C35 for any apparent physical damage 3 Check the contents of the package against the packing list to make sure that all accessories are included in the package After unpacking handle the SLP C35 and its accessories taking care to prevent damage or loss of parts If an inconsistency is found or the package contents are not in order contact your dealer immediately SLP C35 System disk SLP C35J50 CD ROM User s Manual CP UM 5290E 1 This manual The Role of This Manual A total of eight different manuals are available for
12. s Manual Installation amp Configurations Manual No CP SP 1149E This manual is optional sold separately The manual describes the hardware and all functions of this unit Personnel in charge of design manufacture operation and or maintenance of a system using this unit and those in charge of communications software for a system using the communications functions of this unit should thoroughly read this manual This manual also describes installation wiring connections for communications all functions and settings of this unit operating procedures communications with host station such as personal computer communications addresses troubleshooting and detailed specifications SDC35 36 Single Loop Controller User s Manual Installation Manual No CP UM 5289E This manual is supplied with the product Personnel in charge of design and or manufacture of a system using this unit should thoroughly read this manual This manual describes safety precautions installation wiring parameters and primary specifications For further information about operation refer to another manual Installation amp Configurations SDC35 36 Single Loop Controller User s Manual Installation amp Configurations Manual No CP SP 1150E This manual is optional sold separately The manual describes the hardware and all functions of this unit Personnel in charge of design manufacture operation and or maintenance of a system using this unit and
13. setting or other related settings e Items on the horizontal axis are channel numbers when basic functions are being set up and are event output numbers or external switch input numbers when optional functions are being set up e About connection to the personal computer Normally the controller is connected to the personal computer with the dedicated cable By selecting Option Environment Setting and setting Communication Setup to Use CMC10L or Use CMC10B the controller can be connected through the CMC10B L In this case the environment setting and communication setup on the controller main unit must be configured beforehand Configure the controller settings in the offline mode with the cable not connected to the controller Note e For details on functions refer to gt SDC15 Single Loop Controller User s Manual Installation amp Configurations CP SP 1148E SDC25 26 Single Loop Controller User s Manual Installation amp Configurations CP SP 1149E SDC35 36 Single Loop Controller User s Manual Installation amp Configurations CP SP 1150E Step 5 Save setup data When you have finished with the settings save them to a file Saving settings in advance and using saved settings greatly reduces the time required to set up the loader program The following items are saved e Type e Setup parameters 1 Select File gt Save As or press Ctrl A gt gt The Save As dialog box appear
14. the SDC 15 25 26 35 36 Read them as necessary for your spe cific requirements If a manual you require is not available contact Yamatake Corporation or its dealer SDC15 Single Loop Controller User s Manual Installation Manual No CP UM 5287E This manual is supplied with the product Personnel in charge of design and or manufacture of a system using this unit should thoroughly read this manual This manual describes safety precautions installation wiring parameters and primary specifications For further information about operation refer to other manuals Basic Operation and or Installation amp Configurations SDC15 Single Loop Controller User s Manual Basic Operation Manual No CP SP 1147E This manual is optional sold separately The manual describes the functions you can set up only with Simple configuration Personnel in charge of design manufacture operation and or maintenance of a system using this unit should thoroughly read this manual This manual describes installation wiring major functions and settings operating procedures troubleshooting and detailed specifications SDC15 Single Loop Controller User s Manual Installation amp Configurations Manual No CP SP 1148E This manual is optional sold separately The manual describes the hardware and all functions of this unit Personnel in charge of design manufacture operation and or maintenance of a system using this unit and those in charge of
15. 200 of left axis screen display 9999 Display low limit Lower value of vertical axis of 1999 to display upper 10 of right axis screen display limit Display high limit Upper value of vertical axis of Display lower limit to 110 of right axis screen display 9999 e Trend monitor individual Setting Item Setting Range Factory Setting Data type Type of sampled data 0 Not used 8 User defined data Axis Specify an axis used for the graph re Left Right User defined Address of relevant parameter Address of communicable address when the data type is set as parameter user type Station adress Set the station address when a 0 to 127 CMC10B for example is used Station Set the station sub address 0 to 127 sub adress when a CMC10B for example is used B Handling Precautions e When the user defined address is specified make the decimal point setting manually 4 7 Chapter 4 MONITORING 4 8 e Digital trend Setting item Setting Range Address of parameter 256 to 32767 Specified bit of parameter O to 15 Name Name of parameter Up to 10 alphanumeric characters e Selecting trend monitor colors Eile m Trend Monitor Digital Trent Bo D Bo S see Woe ee Bice Bc se Sos Boe Be BS See Bee M ee Bee _ ew GB sens swe ces Cancel When selecting Graph 1 to Graph 16 the color selection screen will appear Select a desired
16. 4 EV2 C 39 EV3 REV C 14 EV2 C 33 EV3 REV 14 EV2 C 33 EV3 REV 15 1 EV3 C 40 EV4 REV 15 1 EV3 C 40 EV4 REV 15 EV3 C 40 EV4 REV C 416 EV4 41 EVS REV C 16 EV4 C 41 EVS5 REV 46 EV4 C 41 EVS5 REV 17 EV5 C 42 EV6 REV C 17 EV5 42 EV6 REV 17 EV5 C 42 EV6 REV C 418 EV6 C 43 EV7 REV 18 EV6 43 EV7 REY C 418 EV6 43 LEV7 REV 419 EV7 C 44 EV8 REV 19 EV7 C 44 LEV8 REV 419 EV7 C 44 EV8 REV 20 EV8 C 45 COMM DI REV 20 EV8 C 45 COMM DI1 REV 20 EV8 C 45 COMM DI REV 21 COMM DM C 46 COMM DI2 REV 21 COMM DM C 46 COMM DI2 REV 21 COMM DM 46 COMM DI2 REV 22 COMM DI2 47 COMM DIS RE 22 COMM DI2 47 COMM DIS REV 22 COMM DI2 47 COMM DIS RE 23 COMM DIS C 48 COMM DI4 RE 23 COMM DIS C 48 COMM DI4 RE 23 COMM DIS C 48 COMM DIREY C 24 COMM DI4 C 24 COMM Di4 C 24 COMM Di4 Trend stop trigger fo Trend save folder C Program Files SLP SLPC35 Trend trigger is only in numeric monitor mode Cancel When setting up the trend triggers the trend can be started and stopped according to the status of the individual monitor The trend trigger setup is valid only while the individual monitor is running When setting up the trend save triggers the trend can be saved according to the status of the individual monitor The file is saved into a specified trend save folder in the TREND Y Y Y Y MM DD HH MM SS CSV form
17. ING AND QUITTING 2 Click the Next gt button gt gt The following screen appears v SOFTWARE LICENSE AGREEMENT 3 If you agree to the software license agreement and wish to install the program click Agree gt To abort the installation click Don t agree gt gt After clicking Agree gt the following screen appears Get Registration Information amatake 4 Enter the user name and company name of a registered user and then click the Next gt button gt gt The following screen appears Display Registration Information 2 2 Chapter 2 INSTALLATION STARTING AND QUITTING 5 Click the Next gt button gt gt The following screen appears Choose Destination Location Note e To change the installation destination directory click Browse 6 Click the Next gt button gt gt The following screen appears Select Components M sample program C Builder M sample program F BASIC POF file iapanese M PDF filefenglish Help filefiapanese M Help filefenglish Note e Check the necessary files To display a PDF file it is necessary to install Adobe Reader For details refer to gt Note on page 2 5 7 Check put a check mark W before the software components you wish to install and click the Next gt button 2 3 Chapter 2 INSTALLATION STARTING AND QUITTING gt gt The following sc
18. ITORING Trend monitor screen Tk i File Trend monitor Option Numeric Monitor Help 1 200 1 000 00 00 00 00 00 00 aly 1 PV al 2 mMy aM 3 SP OF 4 H M JT 5 C M AT 6 CT1 Se el 8 UF l 9 UF el 10 UF el 11 UF l 12 UF el 13 UF el 14 UF ST V5 UF 16 UF aly out aly ouT2 aV Ev aM Ev2 JM Ev3 e Menu configuration list Trend Trend n Starts stops the trend monitor Ctrl T monitor Start Stop T a CSV Read Reads the trend data a CSV Out X Outputs the trend data in CSV format ER Clipboard Graph Outputs an image of the graph to Ctrl C Out the Clipboard Displays the Setup window Numeric Changes the display to the Monitor numeric monitor 4 3 Chapter 4 MONITORING 4 4 e con list __K4____ Returns the graph tothe siari tme 4 Returns the graph by 12 screen 4 returns the graph by 174 soreen p Advances the graph by 174 screen Pe Advances the graph by 12 screen i Advances the graph tothe latest ime TQ feooms outthe graph ndoes the graph zoom a Specify a time scale of the graph e Zooming the graph Drag the mouse from the upper left portion to the lower right portion with the left mouse button kept pressed e Canceling the zoomed graph Drag the mouse from the lower right portion to the upper left portion with the left mouse button kept pressed Chapter 4 MONITORING 4 2 Method of Operation E How to oper
19. No CP UM 5290E SLP C35 Smart Loader Package for the S DC15 25 26 35 36 Single Loop Controller User s Manual lt 2 SS LIII CLIS IIZ Z ELL LILII ILLL G LLLI LL SZ Beir Thank you for purchasing the Smart Loader Package This manual contains information for ensuring correct use of the SLP C35 It also provides necessary information for installation maintenance and trou bleshooting This manual should be read by those who design and maintain devices that use the SDC15 25 26 35 36 and SLP C35 Be sure to keep this manual nearby for handy reference Yamatake Corporation RESTRICTIONS ON USE This product has been designed developed and manufactured for general purpose application in machinery and equipment Accordingly when used in applications outlined below special care should be taken to implement a fail safe and or redundant design concept as well as a periodic maintenance program e Safety devices for plant worker protection e Start stop control devices for transportation and material handling machines e Aeronautical aerospace machines e Control devices for nuclear reactors Never use this product in applications where human safety may be put at risk IMPORTANT Do not apply too much force when connecting the loader plug Doing so might damage the instrument X 4 L Handling Precautions Application of excessive force to the loader plug
20. T F Communications Port COMI en a Communications Pork OMe i Printer Port LPTL Ei Yamatake USB Loader Comm port COMS El I Processors es SCSI and RAID controllers Sound video and game controllers ae Storage volumes 6 Start the Smart Loader Program select Menu Option E and set to the communications port number obtained in the previous step Then press the OK button to complete the configuration Environment Setting Communication Port Communication Setup Port COM1 Port COM2 Port COM3 Port COMA Port COMS Port COME Port COM Port COME Port COMI Por COMIC Port COM11 Port COM12 Port COM13 Port COM14 Port COM15 Port COM1E Transmission speed 4000 bps g600bps 19200bps a0400bps Fixed Cell Width Use Loader Cable Use CMCIOL O Use CMC1OB Station address Station sub address Address 0 Sub Address Selo pats 1 stop bit odd parity no parity 2 stop bits 2 9 Chapter 2 INSTALLATION STARTING AND QUITTING Note 2 10 If the CD ROM for the SLP is not available for the retrieval of the device driver to be installed in step 2 above select Install from a list or specific location Advanced and click the Next gt button Then click Browse to specify the folder in which SLP is installed and click Next gt button Normally C Program Files slp SLPC35 Found New Hardware Wizard Please choose your
21. To display such data use an appropriate spreadsheet application Saving clipboard graph output The display contents on the Trend Monitor screen can be directly saved into the clipboard as a copy of the screen 4 10 Chapter 5 TROUBLESHOOTING 5 1 Error Messages and Remedy E Communications error messages Communication Time out The message cannot be received Check the cable connections and within a period of the time out time contacts An instrument other than SDC15 25 Use the loader with it connected to 26 35 36 is connected SDC15 25 26 35 36 The main unit is not connected Cannot open communications port The communication port cannot be Do not run the loader and other application using the communication port at the same time Communications error has The system error occurs Re operate or quit the loader to occurred restart Windows Trend monitor is active The monitor screen cannot be quitted Quit the monitor screen after the while the trend monitor is running trend monitor has been completed SDC15 25 26 Cannot support currently The loader currently in use is not Contact Yamatake Corporation or 35 36 connected SDC 15 25 26 35 36 applicable to the version of the main its dealer status error unit Loader Lock or Communication The data cannot be loaded from the Cancel the loader lock or password Lock loader since the loader is locked or to restart the operation the password is set
22. at Starting the data sampling When the setup is completed start up the trend monitor Click icon The same operation can be started by selecting Trend Monitor gt Trend Monitor Start The data sampling is started and then the trend of the specified parameters is displayed on the screen e Once the trend monitor is started it continues until the stop operation is performed or the data for 60 000 cycles is sampled e If the stop operation is not performed the data is overwritten onto the old data when the data sampling for 60 000 cycles is completed e The screen can be transited to the Numeric Monitor screen while the trend monitor is running However the loader cannot be quitted or the screen cannot be transited to the Setup screen To do so quit the trend monitor Stopping the data sampling Select Trend Monitor Trend Monitor Stop The trend monitor is then stopped Chapter 4 MONITORING Saving sampled data The data sampled using the trend monitor can be saved into a file in the CSV format The sampled data saved in the CSV format can be processed using spreadsheet applications such as Microsoft Excel n Handling Precautions e The data can be saved into a file even while the trend monitor is running e The data which has been saved into a file is retained in the personal computer unless it Is initialized However the data saved in the file cannot be redisplayed on the loader screen
23. ate the numeric monitor screen Start of monitoring start of communications The operation described below is required to start monitoring Otherwise monitoring and rewriting of data cannot be performed e Click icon The operation is the same by selecting Numeric Monitor Numeric Monitor Start gt gt During normal operation The data on the SDC15 25 26 35 36 is displayed During an error The message Check the device to which the loader is connected is displayed Remedy according to Chapter 5 TROUBLESHOOTING The following operations are possible when the device and the loader are correctly connected Monitoring of run state and changing of parameters Numeric monitor Tag name displayed in table format Process Variable PV Numeric group monitor Set point SP Manipulated variable MV State monitor RUN READY mode displayed in lamp lighting AUTO MANUAL mode format LOACAL REMOTE state Auto tuning start stop state Self tuning start stop state ALARM mode Control output ON OFF state Event output ON OFF state Internal event ON OFF state DI terminal ON OFF state Operation SP value change Operations possible in SP set change numeric changes are Manipulated variable MV change in MANUAL mode limited as follows PID value change RUN lt READY switching AUTO lt MANUAL switching Auto tuning start lt gt stop switching About the operation mode RUN READY mode 0 RUN 1 READY AUTO MANUAL mode 0
24. ation should be done by the administrator or by a user who belongs to the administrator group The USB loader cable is supported on Windows 98 Me 2000 XP Vista 32 bit type It is not supported on 64 bit Windows XP or on Windows 95 Windows NT MS DOS or PC DOS e f there are multiple USB ports connect the USB loader cable to the same port every time If it is connected to a different port there is a chance that driver installation may be required again 1 Put the SLP CD ROM into the CD ROM drive of the personal computer When the installation program starts cancel it 2 Insert the USB loader cable into the USB port gt gt When Windows recognizes the USB cable the notification shown below appears on the task tray and the driver installation wizard appears WD Found New Hardware USB Serial Controller 2 6 Chapter 2 INSTALLATION STARTING AND QUITTING Install the device driver 1 Usually when Windows recognizes the USB loader cable the window shown below appears In some cases depending on the Windows environment it may not appear Select No not this time and click the Next gt button Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows will search for current and updated software by looking on your computer on the hardware installation CD or on the Windows Update Web site with your permission Read our privacy policy Can Windows connect to Windows Update to sea
25. communications software for a system using the communications functions of this unit should thoroughly read this manual This manual also describes installation wiring connections for communications all functions and settings of this unit operating procedures communications with host station such as personal computer communications addresses troubleshooting and detailed specifications SLP C35 Smart Loader Package for the SDC15 25 26 35 36 Single Loop Controller User s Manual Manual No CP UM 5290E This manual This manual is supplied with the SLP C35 Smart Loader Package The manual describes the software used to make various settings for the SDC 15 25 26 35 36 using a personal computer Personnel in charge of design or configuration of a system using the SDC 15 25 26 35 36 should thoroughly read this manual It describes installation of the software ona personal computer operation of the personal computer various functions and setup procedures ll SDC25 26 Single Loop Controller User s Manual Installation Manual No CP UM 5288E This manual is supplied with the product Personnel in charge of design and or manufacture of a system using this unit should thoroughly read this manual This manual describes safety precautions installation wiring parameters and primary specifications For further information about operation refer to another manual Installation amp Configurations SDC25 26 Single Loop Controller User
26. e HTML format ecent File Displays the recent file uit Quits the application Ctrl Q Edit ata Check Checks all setting values Ctrl D Bit edit Inputs to bit lists Ctrl B Input Output Displays the input output port Ctrl P Port setup setup screen m Makes a copy of the source Ctrl C JJ Paste jeee oo f i High function area Initializes the cell size Reads the device s data Ctrl R R Writes the data to the device Ctrl W W a User Function DF User function Displays the user function assignment screen m User function clear Clears user function assignments Foe Option Type Setting Changes the type setup Ctrl T wg Environment Setting Changes the environment setup Ctrl E jHelp __ Version 4 ee eee 3 Communication OCC ELC 3 Chapter 3 SETUP 3 2 Method of Setup Do setup offline without connecting the cable to the controller Click Option on the menu screen Do the following setup tasks Step 1 Set the Smart Loader type Step 2 Initialize clear previous settings Step 3 Set up the environment Step 4 Set up SDC 15 25 26 35 36 parameters Step 5 Save setup data Step 6 Download the settings o Handling Precautions e Steps 1 to 5 are required before the setup parameters are written to the SDC15 25 26 35 36 Be sure to perform these steps Otherwise the SDC15 25 26 35 36 may be set up incorrectly For example the required setup items may not be displayed or un
27. he monitor using the loader connect the loader cable e Before starting the trend monitor configure the settings suitable for the trend monitor e The sampling cycle sometimes shifts due to fluctuations in the communications cycle To perform measurement at exact times use the special recorder or data logger 4 1 Chapter 4 MONITORING mM Screen explanations 4 2 Numeric monitor screen s SLP C35 Monitor Screen Numeric Monitor OFF Trend Monitor OFF File Numeric Monitor M Option O Trend Monitor T Help Basg Numeric Monitor ltem RUN READY AUTO MANUAL LSP RSP Auto Tuning Numeric Monitor Self Tuning ALARM EVENT IHH Proportional Band P Integral time l Derivative time D Singur low inot I eV TT I D IHI Motor adj MHI Motor adj AUTO MANUAL Auto Tuning 1 MANUAL O AT Stop LSP RSP O LSP Heater current CT 1 0 0 Heater current CT 2 AT progress UF4 e Menu configuration list File Quit Quits the Monitor window the Monitor window Ctr Numeric Numeric a Starts stops the monitor Ctrl M Monitor M Start Stop M Option eT Setup Displays the Setup window O Command Line C Displays the Command Line window Trend a Changes the display to the trend Monitor T monitor Help Help Version A Displays the version information Chapter 4 MON
28. le Loop Controller User s Manual Installation amp Configurations CP SP 1150E e Loader lock is enabled Checking details of alarms You can check the details of alarms in the Alarm window when an alarm occurs e Click icon The operation is the same by selecting the Option O Alarm A e The details of the alarm that is occurring are displayed B Handling Precautions e This window displays the details of currently occurring alarms and does not have a function for restoring the SDC15 25 26 35 36 To restore the SDC15 25 26 35 36 you must perform the appropriate remedy described in Chapter 5 TROUBLESHOOTING 4 6 Chapter 4 MONITORING About the numeric group monitor The numeric group monitor can be used when Connect via CMC10 is set by the Environment Setting Communication Setup Connect the loader cable to CMC10B L Up to eight groups can be monitored E How to operate the trend monitor Setup Select Trend Trend monitor individual and Digital trend at Option O Setup and make the following settings for each sampled data 1 to 16 As the cycle and display upper lower limits are common to all channels e Trend Setting Item Setting Range Setting Setting of sampling cycle 1 to 3600s Display low limit Lower value of vertical axis of 1999 to display upper of left axis screen display limit Display high limit Upper value of vertical axis of Display lower limit to 1
29. n gt gt Installation of device driver starts Found New Hardware Wizard Please wait while the wizard installs the software J Yamatake USB Loader Comm port Ycsip sys To C WINDOWS system32 DRIVERS gt gt When the device driver installation is complete the following window Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Click Finish to close the wizard Chapter 2 INSTALLATION STARTING AND QUITTING E 4 Click the Finish button gt gt When the installation is complete the notification shown below appears on the task tray and Windows now correctly recognizes the USB loader cable I Found New Hardware x Your new hardware is installed and ready to use fe 2 22PM 5 Get the number of the Yamatake USB Loader Comm port from Ports COM amp LPT Ports COM amp LPT may be found by navigating to Control Panel gt System Hardware Device Manager for Windows XP 2000 or Control Panel gt System Device Manager for Windows 98 Me Device Manager File Action view Help e m E 4 2 A HIRA 3EFBA3B10A Batteries E Computer age Disk drives cl Display adapters Blk DYDICD ROM drives H Floppy disk controllers cee Floppy disk drives Fy IDE ATASATAPT controllers Keyboards a e Mice and other pointing devices Ee Network adapters SB Ports COM amp LP
30. needed items may be displayed Step 1 Set the Smart Loder type Set the loader program type to match the SDC 15 25 26 35 36 model number 1 Click the icon Selecting Option Type Setting or pressing the Ctrl T key gives the same result gt gt The Type Setting dialog box is displayed Type Setting Basic Model No 2 Mountine APY Input C15 mask size T Panel mounting UUniversal O C25 mask size Output Power voltage O C26 mask size O R0 Relay 4 AC100 to 240W OD DC24V C35 mask size OR1 Position propotionalt MFB Option 1 C36 mask size VO0 Voltage pulse O13EV OVC Voltage pulse Current 23EV AUKC t Ca6TYVUAZT RX O33EV AUX Voltage VD Volt lse Volt O Pa ee 4 2EV independent VVVoltage pulse Voltage pulse O5 2EV dndependent AUX G t Ococurrent O6 2EVOndependent AUX Voltage OCC Current Current Option 2 OCD Current Voltage OGNone 1 CT2 D4 2 0T2 D4 RS485 O DD Voltage Voltage 3 CT2 D2 RSP 4 CT2 DI2 RSP RS485 DO Voltage 2 Set the mounting type control output input type power voltage and additional functions 3 Choose the desired selections for each item 4 Click the OK button Note e Click the Read button to read product data from the device This method prevents the downloading of wrong parameters due to a model number setup error 3 4 Step 2 Initialize Chapter 3 SETUP n Handling Precautions e The type set here is a
31. oard Indicates the operation of pressing the A key with the Ctrl key on the keyboard held down vi Chapter 1 INTRODUCTION 1 1 Overview The SLP C85 is a software engineering tool for the SDC 15 25 26 35 36 Note e Install the SLP C35 on the PC hard disk following the procedure in gt 2 1 Installing the Loader page 2 1 Keep the installation CD as a backup J Handling Precautions E Program functions Setup function Monitoring function Adjustment function e The CD does not contain an operating system OS and cannot be used without one The Smart Loader Package has the following functions e Setup e Monitoring e Adjustment This function is for setting the required controller parameters on the personal computer and writing transferring them to the controller For details refer to gt Chapter 3 SETUP After the setup parameters have been written to the controller it is possible to change and tune control constants while the controller is running to switch modes RUN READY AUTO MANUAL etc and to check RUN status and alarm occurrence The run state can also be checked on the Trend screen and sampled data can be output in CSV format so that it can be handled in third party spreadsheet software such as Microsoft Excel For details refer to gt Chapter 4 MONITORING 1 Handling Precautions e The monitor target is limited to only one unit when monitoring is done via the
32. omputer settings refer to the users manuals provided with Windows and with the personal computer e Windows 2000 Professional XP Professional Only users belonging to the Administrators group can install uninstall this software Windows XP Home Edition Only users belonging to the computer Administrators group can install uninstall this software Running the installer 1 Put the CD in the CD ROM drive of your personal computer gt gt The installation program starts automatically and the following screen appears 4 Welcome Welcome to SLP C345 SDC1 5 25 26 35 38 Setup program This program will install SLP C35 SDC1 5 25 26135 36 on your computer tis strongly recommended that you exit all Windows programs before running this Setup Program Click Cancel to quit Setup and close any programs you Have running Click Next to continue with the Setup program WARNING THIS program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may resultin severe civil and criminal penalties and will be prosecuted to the maximum extent possible under law If an old version of the SLP C35 has been installed the screen shown below appears Click the OK button to delete the old SLP C35 version Delete old version SLP C35 SDC15 25 2 0 e 3 Delete old version SEP 2 25 SU 1a ai eile sia Cancel Chapter 2 INSTALLATION START
33. rch for software Yes this time only Yes now and every time connect a device Click Next to continue 2 For the retrieval location of the device driver to be installed select Install from a list or specific location Advanced and click the Next gt button Found New Hardware Wizard This wizard helps you install software for USB Serial Controller E If your hardware came with an installation CD Sa or floppy disk insert it now What do you want the wizard to do Install from a list or specific location Advanced Click Next to continue gt gt Retrieval of the device driver starts Found New Hardware Wizard Please wait while the wizard searches D USB Serial Controller 2 7 Chapter 2 INSTALLATION STARTING AND QUITTING gt gt When the device driver is found the following window appears Hardware Installation The software you are installing for this hardware Yamatake USB Loader Comm port has not passed Windows Logo testing to verfy its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the corect operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing STOP inssision 3 Click the Continue Anyway butto
34. reen appears Select Start Menu Group Accessories Administrative Tools Note e To change the start menu folder enter the new folder name 8 Click the Next gt button gt gt The following screen appears Start Installation 9 Click the Next gt button gt gt The following screen appears Installation Complete Santel 2 4 Chapter 2 INSTALLATION STARTING AND QUITTING 10 Click the Finish gt button gt gt When the installation is completed successfully the screen will return to the Windows screen Note e Installation of Adobe Reader If Adobe Reader is not installed on your personal computer install it using either of the following procedures e Download Adobe Reader from the Adobe Systems home page e Install adberdr60_enu_full exe from the CD ROM 2 5 Chapter 2 INSTALLATION STARTING AND QUITTING 2 2 Device Driver Installation for USB Loader Cable A device driver must be installed before using the USB loader cable Follow the procedure below to install the device driver E Installing the device driver L Handling Precautions e Be sure to follow the procedure below when installing the device driver The USB cable may not be recognized if the procedure is not followed If the cable is not recognized uninstall the driver and then install it again e Administrator privileges on the computer are required for driver installation Install
35. ric display of the various running parameters parameters can be changed e Lamp indication of the various running modes lamp indications can be operated e Alarm display representative and detailed Trend Monitor screen This screen is for monitoring the running state of the SDC 15 25 26 35 36 in the form of a trend graph e Screen display of trends for max of sixteen data items e Screen display of digital data trends for max of five data items e Export of sampled data as CSV file e Trend screen dumps e Data type PV SP MV user defined data all analog data that can be communicated e Sampling cycle Variable within the range 1 to 3600s e Max sampling count 60 000 fixed regardless of number of data items to sample Note eA CSV file is the data format that can be handled in third party spreadsheet software such as Microsoft Excel In this format sampled trend data can be interpreted in spreadsheet software These screens can be used to perform the following operations e Monitoring of the running state and changing of parameters in the Numeric Monitor screen e Switching of the run mode in the Numeric Monitor screen e Tuning of control constants in the Numeric Monitor screen e Monitoring of trends and sampling of data while the SDC 15 25 26 35 36 is running e Monitoring of alarm states in the Numeric Monitor screen g Handling Precautions e About connection to the personal computer When making the setup or operating t
36. rol constants PID values that are changed relatively frequently while the SDC 15 25 26 35 36 is running can also be set from the Smart Loaders monitor function screen With the setup function parameters that rare need changing once they are set are saved to a file in list format before the SDC 15 25 26 35 36 is started and the saved file is called up and written to the SDC15 25 26 35 36 in a single operation E Screen explanations Menu screen lt SLP C35 Menu Help Setup Monitor e Menu configuration list Tt sep Displays the Setup window Ctrl S Ff Monitor Displays the Monitor Trend Ctrl M window feaman Displays the Adjustment window ores ontion E Changes the envionment setup Cie Jon Jauits nespia cma ee vesna Displays e version nomaron Cia 3 1 Chapter 3 SETUP Setup screen Toolbar Menu bar Intitled SLP C 35 C1I5TROTAOOXX af 7 E eela Be E Selection window m3 w3 w3 wI w3 w3 w w we B B B aii B n Message window Parameter display area Chapter 3 SETUP Menu configuration list File Creates new data Ctrl N 4 Open Opens existing data CirlvO goe frensenstngete amo Save As Saves the active data with a Ctrl A new name CSV Out X CSV Out X Saves the active data in CSV Ctrl X format HTML Out H Saves the active data in HTML format Ctrl H U rint Prints out the data Same contents as data saved in th
37. s Save as Save ri amp My Doounents e a My Pictures File name 635 Save as type SLP C35file c35 x Cancel YW 2 Enter the desired file name and click the Save button 3 7 Chapter 3 SETUP Step 6 Download the settings Write the set parameters or parameters called up from a saved file to the SDC15 25 26 35 36 1 Use the dedicated Smart Loader cable to connect the personal computer to the SDC15 25 26 35 36 2 Turn the SDC 15 25 26 35 36 on 3 Click the icon Selecting Communication Write SLP gt SDC from the pull down menu gives the same result gt gt The message Writing is going to be executed is displayed 4 Click the OK button gt gt This starts the writing of the setup parameters During writing the message Please wait is displayed When writing ends the message Normal end is displayed 1 Handling Precautions e If writing fails the message Communications error has occurred is displayed If writing is not possible refer to gt Chapter 5 TROUBLESHOOTING 3 8 Chapter 4 MONITORING 4 1 Monitor Function E Overview The loader exclusively for the SDC15 25 26 35 36 is used for monitoring SDC15 25 26 35 36 operation To enter the monitor screens click Monitor in the menu screen The loader has the following two monitor screens e Numeric Monitor screen This screen is for performing operations such as changing setups or switching modes e Nume
38. search and installation options 0 Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed C Search removable media floppy CO ROM Include this location in the search Don t search will choose the driver to install Choose thie option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware Proceed with steps 3 to 6 Chapter 2 INSTALLATION STARTING AND QUITTING E Uninstalling the device driver J Handling Precautions e Removing the driver requires restarting the computer Close other applications first and then uninstall the driver e To uninstall the driver administrator rights are required on the computer Uninstalling should be done by the administrator or by a user who belongs to the administrator group 1 Put the SLP CD ROM into the CD ROM drive of the personal computer When the installation program starts cancel it 1 Start the removal program DrvRemover_Ycslip exe by double clicking the icon on the CD ROM If the SLP CD ROM is not available there is also a copy of DrvRemover_Ycslip exe in the folder in which SLP is installed Normally C Program Files slp SLPC35 gt gt A confirmation dialog box for the driver removal appears USB Serial Driver Remover
39. setting for the internal use of the loader program The model number of the SDC15 25 26 35 36 will not change even if the type is changed in the loader program e For an explanation of each of the specifications refer to gt SDC15 Single Loop Controller User s Manual Installation amp Configurations CP SP 1148E on page 1 2 SDC25 26 Single Loop Controller User s Manual Installation amp Configurations CP SP 1149E on page 1 2 SDC35 36 Single Loop Controller User s Manual Installation amp Configurations CP SP 1150E on page 1 2 1 Click the E icon Selecting File gt New or pressing the Ctrl N keys gives the same result gt gt The Initialize Data dialog box appears Information age Ci Initialize Data Cancel 2 Click the OK button gt gt A new file opens 3 5 Chapter 3 SETUP Step 3 Set up the environment Set the communications port and font on the personal computer 1 Click the E The operation is the same by Selecting Option Environment Setting or pressing the Ctrl E keys gives the same result icon gt gt The Environment Setting dialog box appears Environment Setting Communication Port Communication Setup Font size OPort CONI OPort CONS Use Loader Cable O 7 OPort CoM OPort CONt0 Ouse CMCIOL Di OPort COW3 O Port CON11 Ouse CMCIOB OPort COM4 OPort CON12 Station address Station sub address O OPort COWS OPort CON13 3 an 10
40. those in charge of communications software for a system using the communications functions of this unit should thoroughly read this manual This manual also describes installation wiring connections for communications all functions and settings of this unit operating procedures communications with host station such as personal computer communications addresses troubleshooting and detailed specifications iil Organization of the Manual This manual is organized as follows Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 INTRODUCTION Be sure to read this chapter before you start using the Smart Loader Package This chapter describes the required operating environment for the personal computer tells how to install the package and briefly introduces its features INSTALLATION STARTING AND QUITTING This chapter describes how to install start and quit the program SETUP This chapter describes how to set up the data MONITORING This chapter describes how to change the settings as well as the screens monitoring the operation status TROUBLESHOOTING This chapter describes error messages that are displayed when a problem occurs and tells how to remedy the problem Contents Unpacking The Role of This Manual Organization of the Manual Conventions Used in the Manual Chapter 1 1 1 1 2 Chapter 2 2 1 2 2 2 3 Chapter 3 3 1 3 2 Chapter 4 4 1 Chapter 5 5 1
Download Pdf Manuals
Related Search