EMC COMPLIANCE TEST REPORT
Contents
1. and Line 2 recording at least the six highest emissions Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit If EUT emission level was less 2dB to the A V limit in Peak mode then the emission signal was re checked using an Average detector 3 The test data of the worst case condition s was reported on the Summary Data page LINE CONDUCTED EMISSION LIMIT Maximum RF Line Voltage Frequency er Ame 150kHz 500kHz 66 56dBuV 56 A6dBuV 500kHz 5MHz 56dBuV 46dBuV SMHz 30MHz 60dBuV 50dBuV NOTE Line conducted emission test is not applied since the EUT is not AC main powered directly SEC Engineering Service Co Ltd Page9 Report Number SZ1402023 E March 7 2014 7 12 RADIATED EMISSION TEST 7 1 2 1 PRELIMINARY RADIATED EMISSION TEST 1 The equipment was set up as per the test configuration to simulate typical actual usage per the user s manual When the EUT is a tabletop system a wooden turntable with a height of 0 8 meters is used which is placed on the ground plane as per EN 55022 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane 2 Support equipment if needed was placed as per EN 55022 3 All T O cables were positioned to s2. by TUV Rheinland Group January 2005 Instrument Tolerance All measuring equipment is in accord with ANSI C63 4 and CISPR 22 requirements that meet industry regulatory agency and accreditation agency requirement Ground Plane Two conductive reference ground planes were used during the Line Conducted Emission one in vertical and the other in horizontal The dimensions of these ground planes are as below The vertical ground plane was placed distancing 40 cm to the rear of the wooden test table on where the EUT and the support equipment were placed during test The horizontal ground plane projected 50 cm beyond the footprint of the EUT system and distanced 80 cm to the wooden test table For Radiated Emission Test one horizontal conductive ground plane extended at least 1m beyond the periphery of the EUT and the largest measuring antenna and covered the entire area between the EUT and the antenna It has no holes or gaps having longitudinal dimensions larger than one tenth of a wavelength at the highest frequency of measurement up to IGHz SEC Engineering Service Co Ltd Page5 Report Number SZ1402023 E March 7 2014 6 TEST EQUIPMENT LIST Instrumentation The equipment conforms to the CISPR 16 1 ANSI C63 2 1988 Specifications for Electromagnetic Interference and Field Strength Instrumentation from 10 kHz to 1 0 GHz or above Equipment used during the tests For Conducted Emission Test STEM LIS N ETS LINDGREN SEL0021 18 06 2013 1
3. 7 2014 72 ELECTROSTATIC DISCHARGE 7 2 1 ELECTROSTATIC DISCHARGE ESD IMMUNITY TEST Port Enclosure Basic Standard EN 61000 4 2 Test Level 8 kV Air Discharge 4 kV Contact Discharge 4 kV Indirect Discharge Performance Criteria B Standard require Temperature j 20 C Humidity 55 7 2 2 Block Diagram of Test Setup The 470 k ohm resistors are installed per standard requirement VCP EUT Support units amp Support Units v I Ground Reference Plane SEC Engineering Service Co Ltd Pagel5 Report Number SZ1402023 E March 7 2014 12 3 Test Procedure The EUT was located 0 1 m minimum from all side of the HCP Set up the EUT with the support equipment EUT was loaded and executed in windows XP mode He od SR As per the requirement of EN 55024 applying direct contact discharge at the sides other than front of EUT at minimum 50 discharges 25 positive and 25 negative if applicable can t be applied direct contact discharge side of EUT then the indirect discharge shall be applied One of the test points shall be subjected to at least 50 indirect discharge contact to the front edge of horizontal coupling plane 5 Other parts of EUT where it is not possible to perform contact discharge then selecting appropriate points of EUT for air discharge a minimum of 10 single air discharges shall be applied 6 The application of ESD to the contact of open connectors is not required 7
4. 7 06 2014 EMI Test Receiver Rohde amp Schwarz SELOO22 18 06 2013 17 06 2014 For Radiated Emission Test Gi mera 1 Pre amplifer Agilent Technologies p p E 0 1 1300MHz SEL0053 18 06 2013 17 06 2014 rom ETS LINDGREN p Ka Antenna 18 26GHz MINUM SEL0076 12 08 2013 11 08 2014 For Electrostatic Discharge Immunity Test Cal men ESD Simulator SEL0012 03 04 2013 02 04 2014 ESD Ground Plane SGS 3m 3m SEL0004 For Conducted S o WE mw RFGenemto SCHAFFNER SELOO39 12 12 2013 11 12 2014 Coupling Decoupling SCHAFFNER SEL0040 12 12 2013 11 12 2014 a EM EMCLAMP SCHAFFNER SELOOA1 12 12 2013 11 12 2014 SEC Engineering Service Co Ltd Page6 Report Number SZ1402023 E March 7 2014 For RF Strength Susceptibility Test Gi mera L 3msemr Anechoic pTSJINDGREN SEL0017 16 06 2013 15 06 2014 Chamber Signal Generator Rohde amp Schwarz SEL0068 18 06 2013 17 06 2014 Amplifier 30M 1GHz Amplifier Research SEL0066 12 12 2013 11 12 2014 Amplifier 0 8 3 0GHz Amplifier Research SEL0065 12 12 2013 11 12 2014 Power Meter Rohde amp Schwarz SELOO69 18 06 2013 17 06 2014 Cs SommareEMC32 Robd amp kSdwa SELO NA 9 roe periodic Antenna Amplifier Reseach SEL NA 11 High Gain Horn Ka Antenna 0 8 5GHz Amplifier Research SEL0075 For Electrical Fast Transient Burst Immunity Surge Voltage dips and Interruptions Test car era ProPLUS System
5. Basic Standard EN 61000 4 3 Requirements 3 V m with 80 AM IkHz Modulation Performance Criteria A Standard require Temperature 20 C Humidity 55 7 32 Block Diagram of Test Setup K 3 meter OXAXA Chamber EUT amp p Supron Uai EI 1 5 eter z 0 8m Power Amp Signal EUT Monitoring by using a Generator camera PC Controller to control S G amp PA as well as forward power Cantral Raam SEC Engineering Service Co Ltd Page18 Report Number SZ1402023 E March 7 2014 7 3 3 Test Procedure l The EUT was located at the edge of supporting table keep 3 meter away from transmitting antenna it just the calibrated square area of field uniformity The support units were located outside of the uniformity area but the cable s connected with EUT were exposed to the calibrated field as per EN 61000 4 3 EUT was loaded and executed in windows XP mode Setting the testing parameters of RS test software per EN 61000 4 3 Performing the pre test at each side of with double specified level 6V m at 4 steps From the result of pre test in step 4 choose the worst side of EUT for final test from 80 MHz to 1000 MHz at 1 steps n A W N ON Recording the test result in following table 7 Itis not necessary to perform test as per annex A of EN 55024 if the EUT doesn t belong to TTE product EN 61000 4 3 Preliminary test conditions Test level 6V m Steps 4 96 of fundamental Dwel
6. CE EMC COMPLIANCE TEST REPORT For USB 3 0 10M ACTIVE EXTENSION CABLE Trade Name UNITEK Model Number Y 3018 Report Number SZ1402023 E Date March 7 2014 Regulations See below Standards EN 55022 2010 EN 55024 2010 EN61000 4 2 2009 EN61000 4 3 2006 A 1 2008 A2 2010 Prepared for TECH TOP TECHNOLOGY LIMITED ROOM 3 10 F BLOCK A TONIC INDUSTRIAL CENTRE 26 KAI CHENG ROAD KOWLOON BAY HONG KONG Prepared by SEC ENGINEERING SERVICE CO LTD 21A BLDG C SHENNAN GARDEN SCIENCE amp TECHNOLOGY PARK SHENZHEN GUANGDONG CHINA TEL 86 755 86110163 FAX 86 755 86110248 Report Number SZ1402023 E March 7 2014 TABLE OF CONTENTS 1 VERIFICATION OF COMPLIANCE uussserettstsesetetteeesesesssssssseessssssssseeessesessssssseseessesssesessssesessssssnenesessssssssssssssesessssneneeessses 3 STP Ne 4 3 PRODUCT INFORMATION paa 4 d RONNI 4 gt TEST BACH IE Y Os sen nte uU p SIE es A UL EE 5 6 TEST EQUIPMENT LIST Pan 6 T TR 8 71 LINECONDUCTED AND RADIATED EMISSION ttt ttti 8 72 ELECTROSTATIC DISCHARGE mnnvvostesretetttteteessessssenttteseensttttetesssmnnsssentttessesetetteeesesmmneesenttteseenetettesesesssseesenekessenee 15 73 RADIATED ELECTROMAGNETIC FIELD unrnsvsssssssssesssrstttrrrtttmmessssesseeseerstertrermmssssssesesseeseetteertrensssssssseeeseeeteen 18 Si ETO OG ANS rt EO 21 Bl IQHOIOSORTESDSEDUP eee 2 BO PHOTO OFE Ge eenen 23 SEC Engineering Service Co Ltd Page Report Num
7. EC Engineering Service Co Ltd Page22 Report Number SZ1402023 E March 7 2014 8 2 PHOTOS OF EUT SEC Engineering Service Co Ltd Page23
8. Level Factor Loss Factor Level Line Limit Remark MHz dBuV dB n dB dB dBuV m dBuV m dB 150 011 50 60 10 26 1 31 98 30 45 40 00 9 55 Peak 2 180 017 50 84 11 68 1 74 32 08 32 18 40 00 7 82 Peak 3 214 514 55 95 13 03 1 93 32 15 38 76 40 00 1 24 Peak 4 239 987 57 57 14 09 2 07 32 16 41 57 47 00 5 43 Peak 5 480 528 47 87 18 07 3 22 31 62 37 54 47 00 9 46 Peak 6 721 726 47 14 21 10 417 31 22 41 19 47 00 5 81 Peak SEC Engineering Service Co Ltd Page13 Report Number SZ1402023 E March 7 2014 S te Model Number Y 3018 Location Chamber Tested by Ying Polar Vertical Test Mode Working Detector Function Peak QP gem 70 60 30 EN 55022 CLASS B 40 30 20 10 ET 50 100 200 500 1000 Frequency MHz Jm chamber Condition EN 55022 CLASS B 3m VULBS163 2013M VERTICAL EUT USB 3 0 10M EXTENSION CABLE Model 1 3018 Test mode Power Rating AC 230V 50Hz Test Engineer ving Remark Readintenna Cable Preamp Limit Over Freq Level Factor Loss Factor Level Line Limit Remark MHz dBuV dB m dB dB dBuV m dBuV m dB 41 860 47 21 15 57 0 68 32 04 231 42 40 00 8 58 Peak 2 106 013 41 19 14 59 1 25 31 79 25 24 40 00 14 76 Peak 3 150 011 46 20 10 26 1 57 31 98 26 05 40 00 13 95 Peak 4 180 017 46 83 11 68 1 74 32 08 28 17 40 00 11 83 Peak 5 270 375 46 89 14 38 2 22 32 17 31 32 47 00 15 68 Peak 6 480 528 45 57 18 07 3 22 31 62 35 24 47 00 11 76 Peak SEC Engineering Service Co Ltd Pagel4 Report Number SZ1402023 E March
9. Putting a mark on EUT to show tested points The following test condition was followed during the tests Note As per the A2 to EN 61000 4 2 a bleed resistor cable is connected between the EUT and HCP during the test The electrostatic discharges were applied as follows SEC Engineering Service Co Ltd Pagel6 Report Number SZ1402023 E March 7 2014 7 2 4 Performance amp Result V Criteria A The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance wi Criteria B The apparatus continues to operate as intended after the test No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Criteria C Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls FAILED SEC Engineering Service Co Ltd Page17 Report Number SZ1402023 E March 7 2014 7 3 RADIATED ELECTROMAGNETIC FIELD 7 3 4 RADIATED ELECTROMAGNETIC FIELD IMMUNITY TEST Port Enclosure
10. Thermo ELECTRON SELO007 12 12 2013 11 12 2014 en Thermo ELECTRON SEL0008 CM HCOIL H field loop Thermo ELECTRON SELOOIO 12 12 2013 11 12 2014 For General Used Equipment Cal neal Humidity Temperature SELO101 to l 3 Changchun SEL0088 11 07 2013 10 07 2014 The calibrations of the measuring instruments including any accessories that may effect such calibration are checked frequently to assure their accuracy Adjustments are made and correction factors applied in accordance with instructions contained in the manual for the measuring instrument SEC Engineering Service Co Ltd Page7 Report Number SZ1402023 E March 7 2014 7 TEST RESULTS 7 1 LINE CONDUCTED AND RADIATED EMISSION 7 11 LINE CONDUCTED EMISSION 7 1 1 1 PRELIMINARY LINE CONDUCTED EMISSION TEST 1 The equipment was set up as per the test configuration to simulate typical actual usage per the user s manual When the EUT is a tabletop system a wooden table with a height of 0 8 meters is used and is placed on the ground plane as per EN55022 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane 2 Support equipment if needed was placed as per EN55022 3 All T O cables were positioned to simulate typical actual usage as per EN55022 4 The EUT received DC power fro
11. ber SZ1402023 E March 7 2014 1 VERIFICATION OF COMPLIANCE Equipment Under Test Trade Name Model Number Serial Number EUT Powered during test Applicant Manufacturer Type of Test Technical Standards File Number Deviation Condition of Test Sample USB 3 0 10M ACTIVE EXTENSION CABLE UNITEK Y 3018 N A 5V from PC TECH TOP TECHNOLOGY LIMITED ROOM 3 10 F BLOCK A TONIC INDUSTRIAL CENTRE 26 KAI CHENG ROAD KOWLOON BAY HONG KONG OCEAN COMPUTER TECHNOLOGY SHEN ZHEN CO LTD BLOCK 1 NO 6 INDUSTRIAL ZONE YU LV VILLAGE GONG MING TOWN BAO AN DISTRICT SHEN ZHEN EMC Directive 2004 108 EC for CE Marking EN 55022 2010 EN 55024 2010 EN61000 4 2 2009 EN61000 4 3 2006 A 1 2008 A2 2010 SZ1402023 E None Normal The above equipment was tested by SEC Engineering Service Co Ltd for compliance with the requirements set forth in Directive 2004 108 EC and the Technical Standards mentioned above This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment and the level of the immunity endurance of the equipment are within the compliance requirements The test results of this report relate only to the tested sample identified in this report Approved by Authorized Signatory SEC Engineering Service Co Ltd Page3 Report Number SZ1402023 E March 7 2014 2 SYSTEM DESCRIPTION EUT Test Program I The EUT
12. e placement and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level 3 Recorded at least the six highest emissions Emission frequency amplitude antenna position polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and Q P Peak reading is presented RADIATED EMISSION LIMIT Frequency Distance Maximum Field Strength Limit MHz Q P SEC Engineering Service Co Ltd Pagell Report Number SZ1402023 E March 7 2014 7 1 3 Block Diagram of Test Setup EUT USB 3 0 10M ACTIVE EXTENSION CABLE Trade Name UNITEK Model Number Y 3018 PC MONITOR KEYBOARD AC main Nase EUT USB 3 0 10M USB disk ACTIVE EXTENSION CABLR SEC Engineering Service Co Ltd Page12 Report Number SZ1402023 E March 7 2014 7 1 4 Site Summary Data Model Number Y 3018 Location Chamber Tested by Ying Polar Horizontal Test Mode Working Detector Function Peak QP 80 Level dBuVim 70 60 50 EN 55022 CLASS B 40 30 20 10 ET 50 100 200 500 1000 Frequency MHz Jm chamber Condition EN 55022 CLASS B 3m VULB9163 2013M HORIZONTAL EUT USB 3 0 10M EXTENSION CABLE Model 1 3018 Test mode Power Rating AC 230V 50Hz Test Engineer ying Remark Readintenna Cable Preamp Limit Over Freq
13. imulate typical actual usage as per EN 55022 4 The EUT received DC power from PC and PC received AC 230V 50Hz through the outlet socket under the turntable All support equipments received AC 230V 50Hz power from socket under the turntable if any 5 Theantenna was placed at 3 meter away from the EUT as stated in EN 55022 The antenna connected to the Analyzer via a cable and at times a pre amplifier would be used 6 The Analyzer Receiver quickly scanned from 30MHz to 1000MHz The EUT test program was started Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level 7 Thefollowing test mode s were scanned during the preliminary test Preliminary Radiated Emission Test Frequency Range Investigated 30 MHz TO 1000 MHz WORKING 2014 2 22 Y 3018 H V NM Then the EUT and cable configuration antenna position polarization and turntable position of the above highest emission level were recorded for final testing SEC Engineering Service Co Ltd Page 10 Report Number SZ1402023 E March 7 2014 7122 FINAL RADIATED EMISSION TEST 1 EUT and support equipment were set up on the turntable as per step 7 of the preliminary test 2 The Analyzer Receiver scanned from 30MHz to 1000MHz Emissions were scanned and measured rotating the EUT to 360 degrees varying cabl
14. l Time I sec EN 61000 4 3 Final test conditions Test level 3V m Steps 1 of fundamental Dwell Time I sec Range MED Resa Pasa SEC Engineering Service Co Ltd Page19 Report Number SZ1402023 E March 7 2014 7 3 4 Performance amp Result Criteria A Criteria B Criteria C The apparatus continues to operate as intended No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance The apparatus continues to operate as intended after the test No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended In some cases the performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed Temporary loss of function is allowed provided the functions self recoverable or can be restored by the operation of controls PASS FAILED SEC Engineering Service Co Ltd Page20 Report Number SZ1402023 E March 7 2014 8 PHOTOGRAPHS 8 1 PHOTOS OF TEST SETUP RADIATED EMISSION TEST SEC Engineering Service Co Ltd Page2 Report Number SZ1402023 E March 7 2014 ELECTROSTATIC DISCHARGE TEST RADIATED ELECTROMAGNETIC FIELD S
15. m PC and PC received AC230V 50Hz power through a Line Impedance Stabilization Network LISN which supplied power source and was grounded to the ground plane 5 All support equipments received power from a second LISN supplying power of AC 230V 50Hz if any 6 The EUT test program was started Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer Receiver connected to the LISN powering the EUT The LISN has two monitoring points Line 1 Hot Side and Line 2 Neutral Side Two scans were taken one with Line 1 connected to Analyzer Receiver and Line 2 connected to a 50 ohm load the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer Receiver 7 Analyzer Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes 8 During the above scans the emissions were maximized by cable manipulation 9 The following test mode s were scanned during the preliminary test Preliminary Conducted Emission Test Frequency Range Investigated 150KHz TO 30 MHz Then the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing SEC Engineering Service Co Ltd Page8 Report Number SZ1402023 E March 7 2014 7112 FINAL LINE CONDUCTED EMISSION TEST 1 EUT and support equipment was set up on the test bench as per step 9 of the preliminary test 2 Ascan was taken on both power lines Line 1
16. was connected to PC via USB port 2 PC was load and executed in Windows XP system 3 Set up other relative support equipments and work normally during test 4 Keep the EUT working throughout testing 3 PRODUCT INFORMATION Housing Type Plastic Power during test SV from PC VO Port of EUT I O Port Type Tested with USB3 0 Female USB3 0 Male Difference between model numbers as below N A 4SUPPORT EQUIPMENT c Comaxs pur Na fUnsilded Lm Keyboard SK 8115 DELL Shielded 1 8m LCD Monitor AOC Shielded 1 5 m Unshielded 1 8m Note All the above equipment cables were placed in worse case positions to maximize emission signals during mar emission test Grounding Grounding was in accordance with the manufacturer s requirements and conditions for the intended use SEC Engineering Service Co Ltd Page4 Report Number SZ1402023 E March 7 2014 5 TEST FACILITY Location No 1 Workshop M 10 Middle Section Science amp Technology Park Shenzhen China Description There are one 3 chamber and one line conducted labs for final test The m chamber and the Line Conducted labs are constructed and calibrated to meet the FCC requirements in documents ANSI C63 4 and CISPR 22 EN 55022 requirements Site Accreditation Accredited by FCC December 09 2002 The Certificate Registration Number is 709623 Accredited by Industry Canada January 8 2003 The Certificate Registration Number is 46405 4480 Accredited
Download Pdf Manuals
Related Search