Christie Velvet LED Display System
Contents
1. Pixel Num x Frame Rate x 1212012 For example the 10 bit calculation for a 60Hz DVI signal is e 1G Pixel Number x 60 x 10 10 10 e Pixel Number 555 555 x 94 522 221 pixels e Multiply the number of pixels by the number of ports 522 221 x 4 2 088 884 Regulatory This product conforms to the following regulations related to product safety environmental requirements and electromagnetic compatibility EMC Safety e CAN CSA C22 2 No 60950 1 e ANSI UL 60950 1 e IEC 60950 1 e EN 60950 1 e IEC 62471 1 Approvals This product is designed and built to comply with all relevant directives standards safety health and environmental rules and regulations required for the product to be sold in USA Canada EU Australia New Zealand Kuwait China Korea Japan Mexico Ukraine Russia India Argentina Brazil Singapore South Africa and Saudi Arabia Christie Velvet LED Display System Installation and Setup Manual 18 020 101412 02 Rev 1 06 2015 CHRISTIE Electro magnetic compatibility Emissions FCC CFR47 Part 15 Subpart B Class A CAN ICES 3 A NMB 3 A CISPR 22 EN 55022 Class A IEC 61000 3 2 EN61000 3 2 Immunity CISPR 24 EN55024 IEC 61000 3 3 EN61000 3 3 IEC EN61000 IEC 61000 4 2 EN61000 4 2 IEC 61000 4 3 EN61000 4 3 IEC 61000 4 4 EN61000 4 4 IEC 61000 4 5 EN61000 4 5 IEC 61000 4 6 EN61000 4 6 IEC 61000 4 8 EN61000 4 8 IEC 61000 4 11 EN61000 4 11 Environmental Specifications EU D2. maximum power carrying capability For the maximum number of tiles that may be connected per daisy chain when connecting to the power supply refer to the product specifications SHOCK HAZARD A permanent single phase connection must be installed between the LED tile system and the AC power supply FIRE AND SHOCK HAZARD Do not operate the system unless certified power connections providing the recommended voltage are used HIGH TOUCH CURRENT HAZARD To ensure reliable grounding the power connection must be made by using an industrial plug pluggable type B or be provided by a permanent connection A 13 20 A double pole mains circuit breaker certified for the applicable local regulations is required It must be part of the building installation and easily accessible Do not use a wall breaker greater than 20 A This could result in severe damage to the tile system in the event of a failure SHOCK HAZARD Only use the AC power cord provided with the product or recommended by Caution Failure to comply with the following could result in minor or moderate injury Christie TRIP OR FIRE HAZARD Position all cables where they cannot contact hot surfaces be pulled be tripped over or damaged by persons walking on or objects rolling over the cables FIRE HAZARD Do not use a power cord that appears damaged FIRE OR SHOCK HAZARD Do not overload power outlets and extension cords Only Christie qualified technicians are permitted t
3. output connections The line cord has a maximum power carrying capability For the maximum number of tiles that may be connected per daisy chain when connecting to the power supply refer to the specifications in this manual One inlet signal cable can connect to no more than 16 screen cases Top connections Bottom connections EN COJ F bw ASOS A P N wu LA A e pe E A Data connections Input power connections C Output power connections 1 Connect the network cable between the Christie E400 LED Display Controller and the first tile in the array 2 Daisy chain the display port cables from one tile to the next You do not need to make a complete loop between the Christie E400 LED Display Controller and the tiles however with a complete loop communication to the entire array is not lost if one tile fails 3 Daisy chain the power cables from one tile to the next to a maximum of nine tiles 4 Plug the USB cable from the controller to the computer that will be directly connected to the Christie E400 LED Display Controller Related information Cable and control unit layout and design on page 7 Installing the Christie E400 LED Display Controller software The Christie E400 LED Display Controller software controls the configuration of the array 1 Insert the Christie E400 LED Display Controller software CD in the computer 2 Follow the on screen instructio
4. Installation and Setup Manual 020 101412 02 Christie Velvet LED Display System a CHRISTIE NOTICES COPYRIGHT AND TRADEMARKS Copyright 92015 Christie Digital Systems USA Inc All rights reserved All brand names and product names are trademarks registered trademarks or trade names of their respective holders GENERAL Every effort has been made to ensure accuracy however in some cases changes in the products or availability could occur which may not be reflected in this document Christie reserves the right to make changes to specifications at any time without notice Performance specifications are typical but may vary depending on conditions beyond Christie s control such as maintenance of the product in proper working conditions Performance specifications are based on information available at the time of printing Christie makes no warranty of any kind with regard to this material including but not limited to implied warranties of fitness for a particular purpose Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material Canadian manufacturing facility is ISO 9001 and 14001 certified WARRANTY Products are warranted under Christie s standard limited warranty the complete details of which are available by contacting your Christie dealer or Christie In addition to the other limitations that may be specified in Christie s standard lim
5. e is available the green light blinks normally e When the redundancy works the indicator green light fades gradually e When the equipment is running the red light is on e When authorization is occurring the red light blinks e When the PWR button is lit the Christie Christie E400 LED Display Controller is on Inputs Outputs DVI IN DVI OUT OUT1 OUT4 HDMI IN HDMI OUT To PC AUDIO UART IN UART OUT AC 100 240V 50 60HZ Description DVI input DVI output Output for four network interfaces HDMI input HDMI output Computer USB connection Audio input The cascading input interface of the serial ports The cascading output interface of serial ports AC power interface Installing the tiles Install the tiles in the array row by row Do not attempt to construct the array column by column Power on each tile to ensure it is functioning before installing it Warning Failure to comply with the following could result in death or serious injury A e External support for a display wall must be designed and implemented by a Christie qualified installer and must comply with local area regulations and safety standards e All display walls must have permanent external supports The amount of external support required depends on the size of the display wall e A minimum of two people or lift equipment is required to safely lift install or move the product Christie Velvet LED Display System Installation and Se
6. e spanner C Lift the metal loop and place it around the locking mechanism screw on the second tile Make the same adjustments to the locking mechanism screw across all panels If the screw is not the same depth on all panels the panels may be misaligned and the uneven tension between the panels may affect the image quality d Push the spanner in until it is flat against the tile e Repeat steps 6a to 6d for each locking mechanism on the panel 7 Repeat steps 3 to 6 for all remaining tiles to be used in the first row Complete installing all tiles in the first row before installing the second row 8 Repeat steps 2 to 8 for all rows in the array Christie Velvet LED Display System Installation and Setup Manual 11 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup Optional Installing the EOC410 and EOC420 fiber extenders A fiber optic extender increases the available distance between the LED display and the controller The extenders are optional to the configuration of the array and may be necessary based on the signal strength from the control unit Each model of fiber extender can relay content over a specified distance the EOCA410 Single mode SM fiber extender increases the transmission distance by 15 KM and the EOC420 Multi mode MM fiber extender increases the transmission distance by 300 meters Multiple extenders can be chained together between the control unit and the array to extend the distance even f
7. fications Pixel pitch Pixel size Pixel configuration LEDO15 M LEDO19 M 1 538 mm 1 9 mm 1010 1010 1 0 mm x 1 0 1 0 mm x 1 0 mm mm 3 in 1 1R1G1B Christie Velvet LED Display System Installation and Setup Manual 020 101412 02 Rev 1 06 2015 LEDO25 M 192 px x 192 px 160 mm x 160 mm 64 px x 64 px LEDO25 M 2 5mm 2121 2 1 mm x 2 1 mm LEDO30 M 160 px x 160 px 240 mm x 240 mm 80 px x 80 px LEDO30 M 3 0 mm 2121 2 1 mm x 2 1 mm LEDO40 M 120 px x 120 px 240 mm x 240 mm 40 px x 40 px LEDO40 M 4 0 mm 2121 2 1 mm x 2 1 mm 16 CHRISTIE Power requirements Input rating Learn the power requirements for the projector LED Tile LEDO15 M LEDO19 M LEDO25 M LEDO30 M LEDO40 M Christie E400 LED Display Controller LED SM Fiber Extender EOC410 LED MM Fiber Extender EOC420 Environment Input rating 100 240 V 50 60Hz 2 4A 240 watts max 12A max 5 tiles 100 240 V 50 60Hz 2 4A 240 watts max 12A max 5 tiles 100 240 V 50 60Hz 1 5A 150 watts max 12A max 9 tiles 100 240 V 50 60Hz 1 5A 150 watts max 12A max 9 tiles 100 240 V 50 60Hz 1 5A 150 watts max 12A max 9 tiles 100 240 V 50 60 Hz 0 7A 70 watts 100 240 V 50 60 Hz 0 7A 70 watts 100 240 V 50 60 Hz 0 7A 70 watts Specifications Learn about the environment requirements for the product while operating and not operating Non operating environment I
8. fying the tile configuration leeren 15 SPCCIICAUONS 65440945 0655 0808000 IRAE EORR ARR Rao PROV e ME Physical specifications a s a ue won ec wk y o 9 c lO Y e oc se OR e oes RSS e ew 16 bloc ME L TTTTPTTTTTTPITTTTTT 16 Power requirements Input rating llle errors 17 ERVILOEIPHGIU S a sea 9 3 99 9 9 93 eee 1 dde db d di d di d dir di di e di d dii di di ie e Dames d 17 Resolution requirements s aooo ee es 18 RedgulgtOFV 4 6384 eS bee deeee eevee he tives ee ied ce oy S42 OR ee 34 18 ccs a a wea A Gu ee Gee eG ee ee a ie 18 hus CTI 18 Electro magnetic compatibility cce 19 Christie Velvet LED Display System Installation and Setup Manual 3 020 101412 02 Rev 1 06 2015 CHRISTIE Product overview Christie Velvet LED Display System LEDO15 M LEDO19 M LEDO25 M LEDO30 M and LEDO40 M are modular high quality image display units that can be configured into any size or shape The low energy consumption and the long service life of LED technology create display walls that last LED display systems can be quickly and easily deployed into small display configurations while providing the additional features required for larger and more complex installations Terminology Learn about the components of the LED display system Term Definition Tile A cabinet containing several LED modules Array A group of connected tiles forming a larger display Control unit C
9. irective 2011 65 EU on the restriction of the uses of certain hazardous substances RoHS in electrical and electronic equipment and the applicable official amendment s EU Regulation EC No 1907 2006 on the registration evaluation authorization and restriction of chemicals REACH and the applicable official amendment s EU Directive 2012 19 EU on waste and electrical and electronic equipment WEEE and the applicable official amendment s China Ministry of Information Industry Order No 39 02 2006 on the control of pollution caused by electronic information products hazardous substances concentration limits SJ T11363 2006 and the applicable product marking requirements SJ T11364 2006 Christie Velvet LED Display System Installation and Setup Manual 020 101412 02 Rev 1 06 2015 19 Corporate offices USA Cypress ph 714 236 8610 Canada Kitchener ph 519 744 8005 Consultant offices Worldwide offices Italy ph 39 0 2 9902 1161 Australia ph 61 0 7 3624 4888 Brazil ph 4 55 11 2548 4753 China Beijing ph 86 10 6561 0240 China Shanghai ph 86 21 6278 7708 Eastern Europe and Russian Federation ph 36 0 1 47 48 100 France ph 33 0 1 41 21 44 04 Germany ph 49 2161 664540 India ph 91 080 6708 9999 Japan Tokyo ph 81 3 3599 7481 Korea Seoul ph 82 2 702 1601 Republic of South Africa ph 4 27 0 11 510 0094 5 For the most curren
10. ited warranty and to the extent relevant or applicable to your product the warranty does not cover a Problems or damage occurring during shipment in either direction b Projector lamps See Christie s separate lamp program policy c Problems or damage caused by use of a projector lamp beyond the recommended lamp life or use of a lamp other than a Christie lamp supplied by Christie or an authorized distributor of Christie lamps d Problems or damage caused by combination of a product with non Christie equipment such as distribution systems cameras DVD players etc or use of a product with any non Christie interface device e Problems or damage caused by the use of any lamp replacement part or component purchased or obtained from an unauthorized distributor of Christie lamps replacement parts or components including without limitation any distributor offering Christie lamps replacement parts or components through the internet confirmation of authorized distributors may be obtained from Christie f Problems or damage caused by misuse improper power source accident fire flood lightening earthquake or other natural disaster g Problems or damage caused by improper installation alignment or by equipment modification if by other than Christie service personnel or a Christie authorized repair service provider h Problems or damage caused by use of a product on a motion platform or other movable device where such product ha
11. lick Screen Config Select Config Screen and click Next On the Sending Board tab of the Screen Config dialog select the resolution of the video source and click Set e The native display resolution is 320 px by 240 px e Change the X and Y coordinates to move the 320 x 240 window as long as the source size is not exceeded Click Save Switch to the Screen Connection tab Click Read from HW Review the configuration of the tiles in the array and modify as needed The cable layout for the tiles in the array is identified with an S where the first CAT 5 cable starts and the green line shows the path of the daisy chain of cables E identifies the end of the daisy chain Christie Velvet LED Display System Installation and Setup Manual 15 020 101412 02 Rev 1 06 2015 CHRISTIE Specifications Learn about the product specifications Due to continuing research specifications are subject to change without notice Physical specifications Learn the dimensions and weight of the tiles Tile dimensions WxHxD Tile resolution Tile weight Tile design Service access Module dimensions W x H Module resolution Display LED015 M LED019 M 480 0 mm x 480 0 mm x 160 1 mm 16 54 in x 16 54 in x 6 30 in 312 px x 312 px 252 px x 252 px 11 5 kg 25 38 Ib Die cast aluminum Requires both front and rear access 240 mm x 120 240 mm x 240 mm mm 156 px x 78 px 126 px x 126 px Learn about the display speci
12. ns and install the Christie E400 LED Display Controller software Christie Velvet LED Display System Installation and Setup Manual 13 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup Connecting to video sources A Velvet LED Display System array requires a Christie E400 LED Display Controller to display an image using a source connected with an HDMI or DVI cable ensuring the supplied video signal is properly displayed across the entire array After the Christie E400 LED Display Controller is connected and powered up the video content is available as long as the video source is connected Connect the HDMI or DVI output from the video source computer or media player to the appropriate input port on the Christie E400 LED Display Controller Powering on the Velvet LED Display System array If the screen is not in use for more than three days light the screen with 30 of maximum brightness for more than three hours and then with 80 to 100 of maximum brightness to get rid of moisture When the environment temperature is between 10 to 0 degrees Celsius keep the screen blank more than 180 seconds after it starts 1 Start the computer that is the video source 2 Turn on the breaker for the array 3 Turn on the Christie E400 LED Display Controller Powering off the LED display system array When powering off in preparation for inspection or maintenance always disconnect from AC Avoid switching the panel on and
13. nued and proper operation of your product Please see the Maintenance section for specific maintenance items as they relate to your product Failure to perform maintenance as required and in accordance with the maintenance schedule specified by Christie will void the warranty REGULATORY The product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment The product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense CAN ICES 3 A NMB 3 A e 7 PERAT LS ARAA AES BH pzesu Buys HE ABA ODE FSSA 7 uer 71 4 sje AAAA ASE AS Ses Environmental Sha n The product is designed and manufactured with high quality materials and components that can be recycled and reused This symbol X means that electrical and electronic equipment at their end of life should be disposed of separately from regular waste Please dispose of the product appropriately and according to local regulations In the European Union there are separate collecti
14. o open product enclosures Cable and control unit layout and design Before an array is constructed you must plan the design layout of the tiles to make sure that control unit placement and the cabling layout support the overall tile design objectives The LED display system offers considerable flexibility in terms of the number of media sources that can be displayed and the overall resolution Color and brightness matching as well as other functions may be performed across an entire array The video source connections between the cabinets is represented by the blue line The power connections between the cabinets is represented by the red line Christie Velvet LED Display System Installation and Setup Manual 7 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup Electrician connection to mains When installing the cables from tile to tile consistently use either the top or bottom ports for all input connections and the other set of ports for the output connections Christie E400 LED Display Controller interface and ports Learn about the physical ports on the Christie E400 LED Display Controller Front Christie Velvet LED Display System Installation and Setup Manual 8 020 101412 02 Rev 1 06 2015 CHRISTIE Inputs Outputs RUN STA Status PWR Power Rear Installation and setup Description e When no video source is available the green light blinks quickly e When a video sourc
15. off while it is under full luminance when the background of the computer monitor is white as the surge current of power supply system is at the maximum value There must be at least five minutes between turning the off the array and restarting it 1 Turn off the Christie E400 LED Display Controller 2 Turn off the computer 3 Turn off the breaker for the LED array Testing the communication between the control unit and tiles Verify that the array is connected and recognized by the Christie E400 LED Display Controller 1 Launch the Christie E400 LED Display Controller software and login as the administrator a Click User gt Advanced Login b Login with the password admin 2 To confirm the display is connected and recognized by the control unit in the Local System Info area ensure Control System has a value of 1 Christie Velvet LED Display System Installation and Setup Manual 14 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup Switch to the Display Control tab To confirm the control unit is communicating with all tiles select a color from the Self Test list and click Send If the control unit is communicating with all the tiles each display changes to the selected color Reset the Self Test to Normal and click Send Close the Screen Control dialog Reviewing and modifying the tile configuration Review the tile configuration reported in the Christie E400 LED Display Controller software So 2 C
16. on systems for used electrical and electronic products Please help us to conserve the environment we live in CHRISTIE Content Product overview ccc cc ccc ccc oososos ss s n n n n n n n nsn d TOO OOY 6 2c power eae ene ae eae ee aoe eee ER eRe Eee eee Eo eee 4 Related documentation lee eee e eres hono n n non 4 TVOICal LED SG UO ma ae 6 Um wae eo ae A e Ntc cp REOR dE ee ae E oe ee ee 5 Installation and setup ere cere ees nn nnns 6 Sarety quiaelili amp s u aw ay oh ee Ro GS WO ES XE SCORE LS a a oe de 3 6 AC power precautions e ee ee ee onn 7 Cable and control unit layout and design leeren 7 Christie E400 LED Display Controller interface and ports 0000 ee eee 8 Imnstallintj the leS s 2m 4 eR 43 8 3 84 99 9 9 95 3 3 3 9 95 5 3 9 X 2 93 x o E 3 93 Yo 9 Optional Installing the EOCA10 and EOC420 fiber extenders rn 12 RoutbdgtuecdDIB sacas cxx tee et 3 3 9 3 99 o E 9 4 Sow 9 3 S 4 9 0 PO Gn 5 3 33 13 Installing the Christie E400 LED Display Controller software rn 13 Connecting to video sources a ee e e e hme esa hono om nono oa on ron n 14 Powering on the Velvet LED Display System array llle 14 Powering off the LED display system array ell 14 Testing the communication between the control unit and tiles 14 Reviewing and modi
17. ontrols the LED display system array and video input source Pixel A group of one red one green and one blue dot Subpixel A pixel is comprised of three subpixels one for each color red green and blue Each subpixel in LED display technology is an LED chip Pixel pitch Specifies the shortest distance from the center of one pixel to the center of the next pixel SMD package size A technical supplier specification related to the pixel size and denotes the size of the surface mounted diode SMD itself for example the 2 5 mm LED tile has a 2121 SMD package size 2121 2 1 mm by 2 1 mm Fill factor Indicates the ratio between the area covered by pixels and the area not covered by pixels Related documentation Additional information on the Velvet LED Display System is available in the following documents Christie E400 LED Display Control System Software User Manual P N 020 101756 xx Christie Velvet LED Display System Installation and Setup Manual 4 020 101412 02 Rev 1 06 2015 CH TIE l Product overview Typical LED solution A typical LED display system installation contains a variety of components A Media sources B Video matrix switch and splicing video processor Vista X20 C Christie E400 LED Display Controller D Control computer E LED display Christie Velvet LED Display System Installation and Setup Manual 5 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup The configuration of an ar
18. ray depends on the installation Use the following instructions as a guideline only Before installing you must fully understand all site requirements and characteristics Safety guidelines To avoid personal injury or damage to the display system read this information thoroughly before installing the Velvet LED Display System tiles Warning Failure to comply with the following could result in death or serious injury e SHOCK HAZARD Disconnect the product from AC before servicing cleaning removing components or opening any enclosure e SHOCK HAZARD Do not touch the power supply when the power is on e SHOCK HAZARD Observe all electrostatic precautions Use a grounded wrist strap and insulated tools when handling servicing or cleaning electronic assemblies Qo Notice Failure to comply with the following may result in property damage e Always wear clean lint free gloves when handling the product Christie Velvet LED Display System Installation and Setup Manual 6 020 101412 02 Rev 1 06 2015 CHAISTIE Installation and setup AC power precautions Ensure all power precautions are understood before installing the product A certified electrician must be present during installation l Warning Failure to comply with the following could result in death or serious injury Always connect the ground first to reduce shock hazard Do not return the current through the ground SHOCK HAZARD The line cord has a
19. s not been designed modified or approved by Christie for such use i Problems or damage caused by use of a projector in the presence of an oil based fog machine or laser based lighting that is unrelated to the projector j For LCD projectors the warranty period specified in the warranty applies only where the LCD projector is in normal use which means the LCD projector is not used more than 8 hours a day 5 days a week k Except where the product is designed for outdoor use problems or damage caused by use of the product outdoors unless such product is protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set forth in the specifications for such product l Image retention on LCD flat panels m Defects caused by normal wear and tear or otherwise due to normal aging of a product The warranty does not apply to any product where the serial number has been removed or obliterated The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless i Christie has an office in the country where the end user is located or ii the required international warranty fee has been paid The warranty does not obligate Christie to provide any on site warranty service at the product site location PREVENTATIVE MAINTENANCE Preventative maintenance is an important part of the conti
20. t technical documentation please visit www christiedigital com Singapore ph 65 6877 8737 Spain ph 34 91 633 9990 United Arab Emirates ph 971 4 3206688 United Kingdom ph 44 0 118 977 8000 CHRISTIE
21. tem Tile temperature Tile humidity non condensing Operating environment Item Tile temperature Tile humidity non condensing Altitude Control unit temperature Control unit humidity Christie Velvet LED Display System Installation and Setup Manual 020 101412 02 Rev 1 06 2015 Description 10 C to 55 C 14 F to 131 F 10 to 90 Description 0 C to 40 C 32 F to 104 F 10 to 90 O to 3000 meters 20 C to 60 C 4 F to 140 F 10 to 90 17 CHRISTIE Specifications Resolution requirements e The maximum vertical and horizontal resolutions may vary Contact a Christie representative for support if required e 8 bit sources 30 Hz 120 Hz AIl resolutions from 640 x 480 to 1920 x 1200 refer to standard resolutions selectable within the Christie E400 LED Display Controller software e 8 bit sources 30 Hz 60 Hz Resolutions 2048 x 1152 and 2560 x 960 e 10 12 bit sources 30 Hz 60 Hz AII resolutions from 640 x 480 to 1440 x 900 e Custom resolutions are accepted by following the formula below Custom input is restricted to Single Link DVI HDMI using a recommended 94 of the pixels The maximum bandwidth of each output is 1Gbit second and is calculated with this formula Pixel Number x Frame Rate x Red bit depth Green bit depth Blue bit depth 8 bit calculation 1G Pixel Num x Frame Rate x 84 848 10 bit calculation 1G Pixel Num x Frame Rate x 10 10 10 12 bit calculation 1G
22. tup Manual 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup 1 Ensure the external support structure is anchored to the wall and or floor The design and anchoring of the LED display structure is not the responsibility of Christie Digital Systems Contact a Christie representative for structure design options 2 Mount the tiles to the support structure using one of the following methods a To provide lateral stability attach the panel to an external support by the slotted locking pins located on the rear cover of the tile b Attach the tiles to the support structure using M10 bolts in the four mounting points Ensure the M10 bolts have at least 4 mm or three full revolutions of thread engagement into the tile 3 Install the first tile in the center of the bottom row ensuring it is level 4 Install the next tile in the row beside the center tile To help with aligning the tiles in the row each side of the tile has locating pins and holes 5 Adjust the tiles until they are level and no gaps exist between the displays in the array Christie Velvet LED Display System Installation and Setup Manual 10 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup 6 Using the locking mechanism pull the second tile tight against the center cube a Press and hold the locking button below the spanner ilh b Pull down th
23. urther 92 48 9 49 9 Qo Notice Failure to comply with the following may result in property damage e Do not bend the fiber optic cables beyond their minimum bend radius Sharp bends can damage the cables and cause transmission problems e Always keep a protective cap on disconnected fiber optic cables 1 Connect the power cord to the fiber extender 2 Plug the Ethernet cable from the control unit into the fiber extender A 3 Connect the fiber optic cables between the two fiber optic extenders B a Remove the covers from the fiber optic cable ends b Remove the protective plug from the fiber optic ports on the extender C Connect one fiber optic cable into the TX port on each extender d Connect the other fiber optic cable into the RX port on each extender If the fiber optic cables are not plugged into the same port on each extender the LED panels do not display any content 4 Plug an Ethernet cable into the last extender in the chain and connect it to the first panel in the array C 5 Plug the fiber extender power cables into a wall socket Power on all the components in the tile configuration Christie Velvet LED Display System Installation and Setup Manual 12 020 101412 02 Rev 1 06 2015 CHRISTIE Installation and setup Routing the cable When installing the cables from tile to tile consistently use either the top or bottom ports for all input connections and the other set of ports for the
Download Pdf Manuals
Related Search