User manual
Contents
1. SANTEC EMA VIDEO TECHNOLOGIES USER MANUAL Panorama IP camera 1 3 MP Model SNC P3601M Version 1 0m f 0311 engl A6 5 e NTE C User manual SNC P3601M EMA VIDEO TECHNOLOGIES Dear customer Thank you for purchasing a high quality SANTEC device We recommend that you read this manual thoroughly before operating your new System for the first time Please follow all instructions and observe the warnings contained in this manual Please contact your local dealer or use the SANTEC Service Hotline if you have any questions or if you wish to claim for a service or warranty You will find further information on our website www santec video com SANTEC Service Hotline 49 900 1 72 68 32 49 900 1 SANTEC if available from your country support santec video com All rights reserved This publication may not be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the written prior permission of Sanyo Video Vertrieb AG No reproduction of any part or excerpts thereof are permitted Errors excepted Specifications are subject to change without notice for quality improvement SANTEC is a registered trademark of Sanyo Video Vertrieb AG All other companies or products mentioned in this publication are trademarks registered trademarks or brands of the respective company They are not connected in any way wi2. high This means 3 3 V The camera will trigger an alarm if the alarm input has 3 3 V To achieve 3 3 V at the alarm input the contacts are not closed e Alarm out relay Activate deactivate the alarm output o Active type low This means O V If the camera triggers an alarm the alarm output has 0 V o Active type high This means 3 3 V If the camera triggers an alarm the alarm output has 3 3 V O e Trigger an alarm when Ethernet is lost The camera can trigger an alarm if the network connection is interrupted e Alarm relay duration You can set how long the alarm output should be active since the alarm is not being triggered anymore o 0 second The alarm output is set to inactivity immediately after the alarm 10 seconds The alarm output is set to inactivity 10 seconds after the alarm 30 seconds The alarm output is set to inactivity 30 seconds after the alarm 1 minute The alarm output is set to inactivity 1 minute after the alarm Endless The alarm output remains active until the alarm output is manually set to gx e Submit Click here to save the new alarm settings O O O inactivity press button on the live view page of the web interface 31 GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES 3 8 3 SD card 3 8 3 1 SD card settings SD Card Enable ON OFF Submit SD Card Rewrite ON OFF Submit only Alarm Record Support Total Size 3 75 GB Current
3. SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 4 2 Time stamp W Enable Timestamp Timestamp Location Timestamp Format DD MM YYYY TITLE BOTTOM RIGHT e Enable time stamp The time stamp is displayed e Time stamp position O O O UPPER LEFT UPPER RIGHT BOTTOM LEFT BOTTOM RIGHT e Time stamp format O O O O YY MM DD MM DD YY DD MM YY YY MM DD TITLE YY year DD day MM month e Submit Click here to apply the new time stamp settings to the network camera 3 4 3 User User List admin Admin root Operator guest Viewer ee Delete User Add Modify User User Name Password Confirm Authority 5 Admin Operator Viewer 5 mi NTE C User manual SNC P3601M EMA VIDEO TECHNOLOGIES e User list This list displays the user s and their respective authorisations e Delete user Select a user from the list to be deleted and click this button e User name Enter the user name here which is to be added or modified e Password Password of the above user name e Confirm Re enter and thus confirm the password here e Authority Authorisation level admin operator or viewer e Submit Click here to apply the new user settings to the network camera 4 4 4 Language Language English Submit e Language Select your language o English o German e Submit Click here to apply the new language settings to the network camera 4 4 5 Camera name Devic
4. Usage 0 SD Format Format e SD card enable Activate deactivate the SD card e SD card rewrite Activate deactivate the rewriting of the SD card e Format The SD card is being formatted e Submit Click here to save the new SD card settings 3 8 3 2 SD card content Filelist of SD Card Filename Date Time Size 20100416 jpg 2010 04 16 15 24 22 39K Delete 1 file and 3938176 EBytes free e This page displays the content of the SD card e Click on the respective file name to open tt e Click on Delete to delete the file 20 2 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 8 4 Recording 3 8 4 1 Recording settings Schedule Record Upload Via FTP Schedule Record Save Into SD Card Alarm Record Upload Via FTP W Alarm Record Save Into SD Card Alarm Record Upload Via SMTP jpeg only PreAlarm Buffer 0 Second s SD File Format AVI FTP File Format AVI Submit e On this page you can set the recording modes O O O oO Schedule record upload via FTP schedule record save into SD card Alarm record upload via FTP Alarm record save into SD card Alarm record upload via SMTP e mail sending e Additional setting options O O O Buffer Pre alarm buffer can be set to 0 1 2 3 seconds SD file format can be set to AVI JPEG FTP file format only JPEG e Submit Click here to save the new recording settings 33 SANTEC User
5. b Camera web interface You will find the description of the web interface in the following chapter 413 GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES 3 Web interface 3 1 Calling up the camera web interface Open the Microsoft Internet Explorer and start the connection of the network camera as follows e Click on the URL field e Type in the URL address of the network camera and press the ENTER key You will then access the web interface of the camera The default IP address of the camera is 192 168 1 168 You need the user ID and the password in order to access the web interface Password f The default user ID is admin and the default password is 9999 Note When you call up the camera web interface it may happen that you are prompted for an ActiveX installation Please note that the Internet Browser settings allow the installation of ActiveX components dr Favoriten a SNC 390DN W 9 Kicken Se hier um das folgende ActiveX Steverelement zu instabaren NetCam Viewer cab van SANYO VIDEO Vertsieb AG 14 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 2 Live view Administrator Seite LIVE VIEW SNC P3601M So H 264 1260x1024 WHOL rine 28 08 6710 O CON ae ADMINISTRATOR S PAGE Page for camera adjustments LIVE VIEW Page for Live View Live View with 50 resolution Live View with defined resolution
6. manual SNC P3601M EMA VIDEO TECHNOLOGIES 3 8 4 2 Recording schedules Monday From 00 00 To 09 00 Monday v From 15 00 To 21 00 Tuesday From 00 00 To 23 59 ET Monday From 00 00 00 To 00 dF 00 z E Monday y From 00 00 To 00 00 F Monday v From 00 00 To 00 00 F Monday From 00 00 To 00 00 0 123 45 6 7 8 9 101112131415 16171819 20 21 2223 00 0C 19 20 Bs Serie 15 00 27 00 LEE CIO 10 22551 e LUE AA TETE EERE sary TTT TTT TTT TPT EE EE e You can set up to 7 schedules in the camera e Submit Click here to save the new schedule settings e Remove all schedules All existing schedules are deleted 34 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 4 Technical specifications 1 3 MP 1280 x 1024 Web interface Vandal proof Subject to technical changes Errors excepted 35 Your local distributor SANTEC EAV IDEO TECHNOLOGIES www santec video com
7. the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance CE compliance Attention Any changes or modifications to this appliance which have not been explicitly approved of by the respective regulatory authority may lead to a prohibition of usage of this appliance This appliance complies with the CE guidelines User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES Safety instructions e Before operating the appliance please read this manual carefully and retain it for further reference e Before cleaning the appliance it has to be switched off and unplugged from the power outlet Wipe the appliance with a soft damp cloth Do not use harsh cleansers or aerosols for cleaning The type label may not be replaced e Do not use attachments unless recommended by the manufacturer as they may affect the functionality of the appliance and result in the risk of fire electric shock or injury e Never install the appliance in areas exposed to water or other liquids e The camera housing complies with class IP 54 e The appliance has to be installed in a safe and stable location which is able to carry the weight of the appliance Quick stops excessive force and uneven surfaces may cause the appliance to fall Causing serious injury to persons and damage to objects e Openings in the appliance if any are provided for ventilation to ensure reliable operation of the a
8. with the following default settings IP address 192 168 1 168 Subnet mask 255 255 255 0 Gateway 0 0 0 0 DNS server 0 0 0 0 User ID admin Password 9999 To retain the default settings press the reset button There are the following 3 options to change the IP address of the camera a IP finder software Every SANTEC IP camera comes with the IP finder software IP Utility subnet Mask Bootproto WwebFort 2 166 10 234 2 166 10 236 2 160 10 233 2 166 10 230 2 160 10 230 2 168 10 251 2 169 10 232 001E44001 EE 001E44001349 001E44001 FE 001E44001 755 001E443313A0 001E44001 Sac 001E44001 797 001E440017B6 255 209 255 0 255 209 268 0 255 205 55 0 255 209 255 0 255 209 255 0 255 205 455 0 255 205 255 0 255 205 255 0 static static static static static static static static rn ei l l l l l l l static ctatir 160 10 249 7 168 10 741 001E44001 fe A F adn 796 255 265 265 266 266 966 A NT g q g g q gz 166 10 255 g g g q Dynamic IP static IP IP Addr 192 ibs 10 234 Mac Address 001E44001 EE Default Gateway 192 168 10 216 subNet Mask CEE 256 256 1 oe ee IP Find List Clear IP Change Web Contig Select the camera from the list by double clicking Change the IP settings to the new settings Enter the user name ID and the password Click on IP Change
9. D 60HZ 50Hz Rate Control CVBR JPEG Setting Quality high Frame Rate N A 1 MPEG4 Setting Bit rate 4000 Frame Rate 25fps 2 MPEG4 Setting Bit rate 1000 Frame Rate N A Submit e Stream type Adjustment of video streaming mode o Single o Dual o Triple e Video codec Adjustment of encoding procedure o Stream type single H 264 MPEG4 o Stream type dual H 264 JPEG MPEG4 JPEG Dual H 264 Dual MPEG4 H 264 MPEG4 o Stream Typ triple e Resolution The resolution of each video stream depends on the adjustments of the stream type and the video codecs The following values can be set 96 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES Stream type e 1280x1024 e 1280x960 H 264 e 1280x720 e 720x480 Single e 640x480 e 1280x1024 1280x960 1280x720 720x480 640x480 1280x720 640x352 H 264 JPEG 640x480 640x480 MPEG4 e 1280x720 640x352 e 1280x720 390x192 Dual H 264 e 20x480 720x480 e 640x480 640x480 e 1280x720 390x192 Dual MPEG4 e 20x480 720x480 e 640x480 640x480 e 20x480 720x480 H 264 MPEG4 e 640x480 640x480 ace Dual H 264 JPEG e 1280x720 320x192 640x352 p Dual MPEG4 JPEG e 1280x720 320x192 640x352 e Bitrate Bit rate mode o CBR Constant bit rate o CVBR Variable bit rate e JPEG adjustment o Quality HIGH NORMAL LOW o Frame rate 30 15 7 5 3 1 fps e 1 H 264 MPEG4 adjustme
10. Digital output relay on Digital output relay off Audio on camera gt web interface Audio off camera gt web interface Audio on web interface gt camera Audio off web interface gt camera Start recording the video sequence is saved as AVI file Q amp 34 Cy nc stor 15 GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES Notes e n order to activate the 2 way audio function press the c3 and F2 buttons e In order to save a snapshot or a video sequence select the storage location by using the SD button e During live mode of the web interface digital PTZ control is not possible Please use the SanGuard or NUUO software which you can purchase from SANTEC 16 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 3 Setting overview SANTET ADMINISTRATOR S PAGE LIVE VIEW Main M dE Data and Time Setting Basic Setti E E Data and Time Setting amp System User Setting The Local Time Daylight Saving Time Is Actve Language Setting Date 2010 06 02 Time 09 12 46 The Desired Time o Device Name Set Manually Update Firmware Date 2010 06 02 YYYY MM DD TS s T 3 WAN Setting Time 09 09 06 HH MM SS SNTP Setting Synchronize with Computer Time Date 2010 06 02 Time 09 08 56 f DDNS Setting Synchronize with SNTP Server Event
11. Log SNTP Server 0 pool ntp org Automatically Adjust for Daylight Saving Time Changes L caries Soti Time Zone GMT 01 Amsterdam Berlin Rome Advanced Setting S Motion Detection 7 SCANTEG User manual SNC P3601M EEEAVIDEO TECHNOLOGIES 3 4 System settings 3 4 1 Time date The Local Time Date Time The Desired Time D Set Manually Date 2010 05 10 YYYY MM DD Time 09 13 128 HH MM SS Synchronize with Computer Time Date Time Synchronize with SNTP Server SNTP Server 0 pool ntp org v Automatically Adjust for Daylight Saving Time Changes Time Zone GMT 01 Amsterdam Berlin Rome v Submit e Local time The local time is the one as set in the camera e Desired time You can change the time which is set in the camera as follows o Set manually Select the desired time and date from the drop down list o Synchronize with computer time If you select this option the computer time date is transferred to the camera o Synchronize with SNTP server If you select this option the SNTP server time date is transferred to the camera e Automatically adjust for daylight saving time changes This option activates the automatic adjustment to summer winter time e Time zone This is the time zone in which the camera is located This option is important for daylight saving time changes e Submit Click here to apply the new date time settings to the network camera 18 User manual
12. ctric shock e Never insert items into the openings of the appliance They may touch parts under electric current which may cause an electric shock e Never pour any liquids over the appliance 5 e NTE C User manual SNC P3601M EMA VIDEO TECHNOLOGIES e In case of any operating interruption or a complete operating failure please switch off the appliance and disconnect it from the wall outlet Never attempt to service or repair the appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel e When replacement parts are required be sure that the service technician uses replacements parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards e Upon completion of any service or repairs to the appliance ask the service technician to perform safety checks to verify that the appliance is in proper operating condition e The appliance should only be installed by qualified service personnel and has to comply with local specifications and regulations e Never point the camera at an object with a high degree of luminance Bright vertical or horizontal lines can result in a distortion outshine of the entire image on the monitor This artifact is not an error but a particularity of semiconductor CCDs when they are directly exposed to a power
13. e 2 From i min 4 max e Audio Set the audio mode to o OFF audio is turned off one way audio only from camera to PC o two way audio in both directions e Audio out volume 0 4 e Submit Click here to save the new audio settings 99 GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES 3 8 Extended settings 3 8 1 Motion detection Motion Detection Enable Disable Lowest User Setting Submit Sensitivity e Motion detection Activation deactivation of motion detection e Sensitivity Set the sensitivity level of the motion detection O O O O Lowest Low Medium High Highest e CCD reference CCD reference 20 50 e Motion detection mask Click on the picture to set or to delete an element of the motion detection mask If a motion occurs in the marked field it will be detected e Submit Click here to save the new motion detection settings 30 User manual SNC P3601M SANTEC EEEAVIDEO TECHNOLOGIES 3 8 2 Alarm settings Alarm In Sensor ON OFF Active Type Low Alarm Out Relay D ON OFF Active Type Low Trigger an Alarm When Ethernet Is Lost Alarm Relay Duration 0 second Second s Submit e Alarm in sensor Activate deactivate the alarm input o Active type low This means 0 V The camera will trigger an alarm if the alarm input has 0 V To achieve 0 V at the alarm input the contacts are closed o Active type
14. e Namen SNC P3601M Best tigen e Camera name Enter the name title of the camera e Submit Click here to apply the new camera name to the network camera 90 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 4 6 Update firmware Software Version SNC S65IR W 2 2 001E440017B6 ActiveX Version 1 0 1 9 Durchsuchen and click update Note Do not move another page and disconnect the power of the device during the update Update will take a ximately 1 minute Warning System will restart immediately This page displays information on the installed firmware version and the ActiveX components e Search Select the firmware file from your PC e Update Start the update process e Restart Restart the camera _91 GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES 3 5 Network 3 5 1 IP address Enable DHCP IP Address 192 168 1 168 Netmask Gateway Be CR ee 1 s DNS 2 s DNS Pan a OB we S HTTP Port 80 Submit e IP address Enter the 4 Byte IP address value from 0 to 255 Every network camera has to have its own IP address which can be identified in the network e Netmask Enter the 4 Byte subnet mask value from O to 255 By this the netmask can be identified in which the network camera is located e Gateway Enter the 4 Byte gateway value from 0 to 255 e First DNS Enter the 4 Byte DNS server address value from 0 to 255 The DNS server transforms the d
15. ful light source e Atthe installation site the camera has to be adjusted to the given light conditions e Please respect the local legal regulations on waste if you need to dispose of discarded appliances This symbol means that electrical appliances need to be disposed of properly and not sd simply with unsorted household refuse Please respect local regulations on waste disposal About this user manual This manual aims at assisting the user on how to operate camera SNC P3601M This manual is subject to rigid quality control However no guarantee can be given that mistakes are not present We reserve the right to make changes to the manual without prior notice Before operating the appliance please read this manual carefully and retain it for further reference Verify that all appliance items are included in the delivery Should items be missing do not operate the appliance and contact your local dealer Never attempt to repair the appliance yourself This should only be done by qualified service personnel Improper handling of the appliance will invalidate the warranty Items included in the delivery 1x camera SNC P3601M 1x IP finder software 1x allen wrench 1x user manual 1x torx key 4x rubber gaskets 4x screws To operate the camera SanGuard or NUUO software is required which you can purchase from SANTEC User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 1 Installation also see the pictures on the fol
16. lowing pages Camera SNC P3601M is a colour camera with electronic day night switching and a pre installed 360 lens You will find the technical data at the end of the manual 1 1 Lens This camera is equipped with a pre installed and pre set 360 lens When operating the camera you may need to re adjust the lens because during the transport the lens might have experienced some vibrations Step1 Unwrap the camera Step 2 Connect the camera to the power supply and connect it to the network Step 3 Open the cameras s web interface in the Internet Explorer Step 4 Call up the live Step 5 Check if the oval position is centered and straight Step 6 Check if the focus adjustment is set properly Step 7 If required adjust the lens To access the lens open the camera housing and following the below procedure Use the allen wrench included in the delivery Continue on next page GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES Ensure that the main screw and the focus screw are loose They have to be loose but don t need to be taken out completely 2 Turn the focus ring left or right until the picture is sharp and clear Turn the master ring left or right to obtain a straight position of the elliptical picture Turn the adjustment screw left or right to obtain a vertical position of the elliptical picture The elliptical picture has to be in a centered position Turn the adjustment screw lef
17. nt o Bit rate 64 4000 Kbit sec o Frame rate 30 25 15 13 7 5 6 fps e 2 H 264 MPEG4 adjustment o Bit rate 64 4000 Kbit sec o Frame rate 30 25 15 13 7 5 6 fps e Submit Click here to save the new encoding settings Note Although the camera provides a number of video modes single H 264 MPEG4 mode with 1280 x 1024 resolution has always to be set in order to enable a digital PTZ contol using SanGuard or NUUO software S07 SCANTEG User manual SNC P3601M EEEAVIDEO TECHNOLOGIES 3 6 2 Camera settings Sens UP OFF Day and Night Auto White Balance AUTO WDR ON OFF WDR Level 5 DC IRIS 110 gt 1 250 Brightness 128 gt 0 255 Contrast 128 gt 0 255 Saturation 128 gt 0 255 Sharpness 128 gt 0 255 Noise Reduction 128 gt 0 255 default On this page you can change the following picture settings O O O O O O O OOOHOO Sens up OFF ON Day and night AUTO B W COLOR White balance AUTO SUNNY SHADOW INDOOR LAMP WDR ON OFF WDR Level 1 10 DC IRIS 0 200 Lens type DC IRIS MANUAL Brightness 0 255 Contrast 0 255 Saturation 0 255 Sharpness 0 255 Noise Reduction 0 255 e Reset The picture settings are reset as shown on the above screen shot e Submit Click here to save the new picture settings 28 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 7 Audio settings Audio OFF v Audio Out Volum
18. omain name into an IP address e Second DNS Enter the 4 Byte DNS server address value from 0 to 255 The DNS server transforms the domain name into an IP address e HTTP port Displays the specific HTTP port number Default is 80 e Submit Click here to apply the new network settings to the network camera 02 User manual SNC P3601M SANTEC EEEAVIDEO TECHNOLOGIES 3 5 2 SNTP time server for time synchronisation SNTP Server 0 pool ntp org Submit e SNTP server IP address of the SNIP server Can be entered as 4 Byte IP address or as domain name e Submit Click here to apply the new network settings to the network camera 3 5 3 FTP FTP Server 192 168 1 2 Port 21 User Name Password File Upload Path default_folder Submit e FTP server IP address of the FIP server Can be entered as 4 Byte IP address or as domain name e Port Port number of the FTP server e User name User name to login to the FTP server e Password Password to login to the FTP server e File upload path Folder path of FTP server in which the video data is to be stored e Submit Click here to apply the new network settings to the network camera 503 SCANTEG User manual SNC P3601M EEEAVIDEO TECHNOLOGIES 3 5 4 SMTP My Server Requires Authentication Account Name Password Sender SMTP Server 192 168 1 1 Email Address Storage Setting Send Count 4 Submit If necessary enable the opti
19. on My server requires authentication e Account name Account on e mail server e Password Password of account on e mail server e Sender This information is displayed as e mail sender e SMTP server IP address of SMTP server Can be entered as 4 Byte IP address or as domain name e E mail address E Mail address to which the e mails are to be sent e Send count 1 8 Number of files attached to an e mail e Submit Click here to apply the new network settings to the network camera _ 94 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 3 5 5 DDNS dynamic domain name system E Enable DDNS Function DDNS Host Name test dyndns org DDNS Account test DDNS Password occo e DDNS host name IP address of DDNS server Can be entered as 4 Byte IP address or as domain name e DDNS account Account on DDNS server e DDNS password Password of account on e mail server e Submit Click here to apply the new network settings to the network camera 3 5 6 Event protocol Date and f Events Time 1 2000 01 01 01 10 06 login on ffff 192 168 1 169 On this page the events are displayed You can browse in the events by clicking on the buttons first page previous 20 and next 20 95 GANTEC User manual SNC P3601M EMA VIDEO TECHNOLOGIES 3 6 Video settings 3 6 1 Encoding Stream Type Single Video Codec Single MPEG4 Resolution MPEG4 720 1280x7 20 ad 50Hz or 60HZ
20. ppliance and to protect if from overheating These openings must not be covered or blocked Please make sure that the appliance does not overheat e The appliance should only be operated from the type of power source indicated on the marking label If you are not sure of the type of power supplied at the installation location please contact your local dealer e An appliance which is powered through a polarized plug a plug with one blade wider than the other will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug into the outlet try reversing the plug Do not defeat the safety purpose of the polarized plug e lf the appliance is powered through a grounding type plug the plug will only fit into a grounding type power outlet This is a safety feature If your outlet does not have the grounding plug receptacle contact your local electrician e Route power cords and cables in a manner to protect them from damage by being walked on or pinched by items places upon or against them e For protection of the appliance during a lightning storm or when it is left unattended and unused for a longer period unplug the appliance from the wall outlet Disconnect any antennas or cable systems that may be connected to the appliance This will prevent damage to the appliance due to lightning or power line surges e Do not overload wall outlets and extension cords as this can result in a risk of fire or ele
21. t or right to obtain a horizontal position of the elliptical picture The elliptical picture has to be ina centered position Fix the screws again tightly User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES 1 2 Camera installation Make sure to fix the camera onto a solid basis which is capable to carry the weight of the camera Ensure that the camera is safely installed by using only suitable screws If the included screws are not suitable please replace them by other appropriate screws 1 3 Power supply The camera can be operated with 12 V DC via the external power supply unit or with PoE Power over Ethernet via a PoE switch Ethernet port 1 4 Camera overview Picture 1 Open the camera housing ti A Screws to open the camera housing SCANTEG User manual SNC P3601M EMA VIDEO TECHNOLOGIES Picture 2 Reset button Reset button Picture 3 Lens adjustment Screws Screws to adjust the position of the elliptical picture 10 User manual SNC P3601M SANTEC EMA VIDEO TECHNOLOGIES Picture 4 Dimensions mm 135 135 Picture 5 Surface mounting Screws for surface mounting SANTEC EEEAVIDEO TECHNOLOGIES Picture 6 Connections User manual SNC P3601M Ethernet connection Voltage 12 V DC Audio input output Alarm input output wi a User manual SNC P3601M ANTE C EMA VIDEO TECHNOLOGIES 2 IP settings The SANTEC IP cameras come
22. th Sanyo Video Vertrieb AG Copyright by Sanyo Video Vertrieb AG Ahrensburg Germany User manual SNC P3601M Table of contents Safety precautions Safety instructions About this user manual 1 3 Power supply 1 4 Camera overview SANTEC EMA VIDEO TECHNOLOGIES OO O1 R O O O NN 2 IP settings 3 Web interface 3 1 Calling up the camera web interface 3 2 Live view 3 3 Setting overview 3 4 System settings 3 4 1 Time date 3 4 4 Language 3 4 5 Camera name 3 4 6 Update firmware 3 5 Network 3 5 6 Event protocol 3 6 Video settings 3 6 1 Encoding 3 6 2 Camera settings 3 7 Audio settings 3 8 Extended settings 3 8 1 Motion detection 3 8 2 Alarm settings 3 8 3 SD card 3 8 3 1 SD card settings 3 8 3 2 SD card content 3 8 4 Recording 3 8 4 1 Recording settings 3 8 4 2 Recording schedules 4 Technical specifications SCANTECG User manual SNC P3601M EMA VIDEO TECHNOLOGIES Safety precautions Caution CAUTION DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Description of symbols Danger This symbol is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a person Warning This symbol is intended to alert the user to
Download Pdf Manuals
Related Search