INSTRUKCJA OBSŁUGI - Gardiner Pole Systems
Contents
1. black nozzle nut R64 take out the nozzle core wash it lubricate the O ring on the core and reassemble it again Unscrew the cap of the tank RP11 take out the funnel RP22 take out the diaphragm tank cap R322 without removing it from the hose then take out the o ring and wash or exchange the filter When it s done put the filter and the o ring back into the R322 Then put the diaphragm tank cap R322 inside the tank When placed in a tank make sure that the cap touches the bottom of the tank Note All repairs replacements or maintenance of the pump battery or control panel can be done only in the Marolex premises or by authorized services Repairing replacing or maintenance of the elements mentioned above on their own results in loss of warranty General Comments In the lance s handle there s a filter R40 installed designed to protect nozzles from clogging All Marolex lances are interchangeable the same thread in all of them It is possible to use additional extensions 60 and 100 cm produced by Marolex With MAROLEX sprayers a wide range of nozzles can be used cone shaped deflecting flatstream with adjustable stream angle and with different output The construction of Marolex lances allows the use of nozzles produced also by other manufacturers Children pregnant women people taking drugs or drinking alcohol should not operate the sprayer The operation of the sprayer should be tested with clean water firs2. but not longer than 36 months from the date of production Sprayers with chemical remains will not be repaired Reclamation should be lodged to the seller of the sprayer The claims will be accepted after showing the defected part or giving the full description of the fault Number of repairs after which the seller can t refuse to exchange the sprayer for a new one in case there are still defects is 3 Operations connected with exploitation of the sprayer and described in the manual are not treated as guarantee repairs The producer won t accept the claim if there were changes in pressure regulation or the storing operating maintaining of the product were not according to the manual Mechanical damages caused by the user can t be the subject to reclamation The damaged parts can be exchanged but the costs are charged The manufacturer will not accept warranty claims if the user makes any repairs replacements or changes in the pump battery or the control panel 10 Manufacturer will not accept warranty claims if the sprayer was stored used or serviced in improper way N date of the repair description of the fault stamp of the retailer and the date Telescopic lance with handle R010mx Telescopic lance without handle R01mx 212 15 Feeding valve integrated with handle RO20j Battery R318 Container cap Lance fi 12 mm Lance pipe fi 8 mm Clasp faucet fi 8 mm Feeding valve trigger La
3. fully charged At least every three months the battery charge level should be checked and if necessary the battery should be recharged in order not to allow to its total discharge which can cause damage Preparing for work e Remove the sprayer from the carton e Connect the lance with the feeding valve integrated with handle R020j e Open the cap RP11 and fill in the sprayer with clean water to check the operation of the device e Switch on the button on the control panel and press the trigger on the handle e If the sprayer works and the battery is sufficiently charged for work then we can start preparing for spraying e The charge level is displayed on the control panel e In a separate container prepare a liquid according to the recommendations the packing of the pesticide e Pour the liquid into a container using the sieve with funnel RP22 Sprayer s operation Start the sprayer button on the control panel Holding the handle of the lance press the trigger button and start spraying During operation the pump will automatically maintain a constant pressure If the battery gets discharged during work the user will be warned about it by a light signal and sound alert After finishing the spraying rinse the sprayer using clean water In order to do it pour some clean water into the container start the sprayer and spray until the device stops to suck liquid from the tank and will suck some air Then You should
4. turn off the sprayer and completely empty the tank of the liquid NOTE After finishing all operations make sure that the battery is sufficiently charged to store store the sprayer with a charged battery and the sprayer was turned off using the button on the control panel Usage recommendations Do not store the sprayer sunlight or temperatures below 4 C It is not recommended to fill in the tank above the working capacity During operation do not put the sprayer on one side because instead of liquid the air can be sucked If you observed increased resistance the feeding valve lubricate the seals with silicone lubricant or they can get damaged When working with plant protection chemicals it is necessary to comply with safety rules and strictly follow the instructions on the packaging of chemicals If you leave some liquid the lance during winter expanding ice may damage the valve and the handle Bequipment After finishing work cleaning the sprayer and blowing air through it you should Unscrew hose connected to the handle remove R40 filter and clean it preferably under running water Unscrew the bottom nut R50 from the feeding valve 8020 remove the valve piston with a spring clean it lubricate with silicon lubricant put it back into the valve and screw in the nut tight Unscrew the yellow nozzle R115 then unscrew the
5. 99 AROL Electric INSTRUKCJA OBS UGI OWNER MANUAL OPRYSKIWACZ W ZKOWY AKUMULATOROWY BATTERY CART SPRAYER BATTERIESPRITZE PULVERIZADOR DE elec er ME DE RODAS 79 Application of the Sprayer 4 nennen 16 Standard equipment 16 Charging the battery 16 Preparation for work and 17 Preparing for work naeh nannte 17 Sprayer S operation eee aie 17 Usage recommendations 17 Equipment maintenance 18 General COMMENTS 18 Safety Information Technical information and symbols of the elements Construction and maintenance of APS telescopic lance Construction and maintenance of the feeding valve integrated with handle The Controlpanel Troubleshooting oes R Removal a a Disposal A e ee aes Terms of repairs guarantees 24 List of schema elements Thank You for buying our sprayer Before using the sprayer this manual should b
6. alve s piston included seized kits 208 2082 or replace the entire handle with valve RO20j Weak spraying R40 filter dirty Unscrew the hose remove the action although the pressure in the tank is high R40 filter and clean it or replace with a new one found in kits 208 Z08b R40 Clogged nozzle in the lance Unscrew the nozzle cap R115 then the nozzle nut R64 take out the nozzle core R114 and rinse all parts under running water lubricate the o ring on the nozzle core and assemble Symptoms Reason Solution Leaks in the joints of the lance Lost R47c seal or loose nozzle nut R64 Insert the seal R47c or tighten the nozzle nut Unsealed or incomplete system of the telescope lance Tighten or repair the telescope system in the lance There s air appearing in the In the pump there is air mixed with a liquid too Repeatedly turned on and off the sprayer by pressing the switch button hose or liquid little liquid or tilted or add the liquid to the container stream is being sprayer interrupted Not possible to Dirty sieve R322 Clean the sieve R322 reach the maximum Dirty pressure pump Contact Marolex service pressure serwis marolex pl In case of other symptoms preventing proper operation of the sprayer please contact MAROLEX service at serwis marolex pl Removal and Disposal We offer technical support and on line help s rwis mar
7. e read carefully and kept for future reference To ensure long term operation of the device the safety operation and maintenance recommendations enclosed in the manual should be strictly observed Application of the sprayer Battery sprayer trolley V is designed for spraying pesticides and liquid fertilizers in gardens orchards parks forests nurseries and greenhouses Standard equipment Each packing of the Sprayer V contains Complete sprayer with the wheels pump battery 7 2Ah Hose 250cm with the feeding valve integrated with the handle RO20j Telescopic lance with adjustable nozzle MR1 5 1 5mm spraying angle 45 Battery charger Funnel with a sieve Regulated cone nozzle MR1 0 1 0mm spraying angle 45 Flatstreem nozzle for herbicides MF3 110 3mm spraying angle 110 Seals a vial of silicone lubricant and other parts User manual and warranty card Charging the battery To charge the battery plug in the enclosed charger to the charging socket on the control panel and then connect with the power supply of 230V 50Hz Site 22 The battery is fully charged when all LED charge indicators are illuminated as well as the control 100 If the battery has a low charge level and the LEDs indicators light only in red it s necessary to charge the battery before further work The battery should be charged only when the sprayer is switched off Charging the battery should be finished only when the battery is
8. hen tighten the sleeve so that the lance could not fold again Telescopic lance is provided with a special antidust system APS The system protects the telescopic lance system against contamination In order to maintain the system unscrew the sleeve and take out the inside lance pipe by pulling it out Lubricate with silicone grease all the elements on the inside lance pipe R106 R107 R108 and R109 When it s done put back the pipe A inside the outer lance pipe and screw the sleeve 106 108 109 107 RZ3nx Jas A B Construction and maintenance of the feeding valve integrated with handle Feeding valve integrated with handle consists of many elements which ensure proper operation of the sprayer Its main advantages are Ergonomic design fitted to the shape of the hand Comfortable to use trigger button dditional filter inside the lance giving protection against polluting Two systems of work intermittent and continuous Two systems of work give us the ability to work Intermittent the possibility of a temporary spray obtained by pressing the trigger button R44 The moment the button is released the spraying stops Continuous possibility of continuous spraying without necessity of pressing the trigger button R44 during spraying It is obtained by pressing and moving forward the trigger button R44 till it is blocked To unblock the button press it and move backward u
9. nce handle Filter Hose end piston Hose nut R80e Nozzle nucleus Nozzle nut Nozzle 1 5 nut for MR Piston Spring Nut without hole Brass bar fi mm Lance ring clasp z 5 Telescope ring faucet Clasp ring O ring 11 3 2 4 O ring 10x2 O ring 8x2 RI08 O ring 5 3 2 O ring 100x3 Funnel with sieje Container s cap seal Diaphragm tank nut filter FESTER RULUMX R73nx50 R73mx60 ___ R115_1 5 R114R116 864 R4 1 1 R1U3 RLU6 RLUS RLUY 0 RLU MLL R44 O R43 Raga R C R gt U MAROLEX Sp z o o ul Reymonta 2 05 092 Dziekan w Le ny POLAND www marolex pl 077 PL GB DE PT RUS 2014 A
10. ntil the brass element is at the end of the button hole Maintenance is described in the section Equipment maintenance K81e Kole gt R020j The control panel MAROLEX 1 battery upraryer c 0 charging complete charging in progress LED charge indicator switch button charging socket Symptoms Reason Solution Sprayer does not work Swich button off Press the switch button on the control panel Discharged battery Charge the battery process on the control panel will show Despite charging the sprayer the control panel does not light up Charger does not work Buy new charger Defect in control panel Contact Marolex service Feeding valve R020j leaking Loose hose nut R80e or damaged gasket R47c Tighten the nut or replace the gasket R47c found in repair kit 208 or washers kit Z08u Freezing water ruptured handle or valve Replace the valve 8 handle RO20j Damaged valves cylinder top gasket it wasn t lubricated periodically Replace the piston with the o rings found in kits 208 and 7082 or even the entire RO20j valve Lost seal R47c or unscrewed lance Insert the seal R47c or screw the Trigger button is in Unblock the trigger button by Blocked trigger button R44 continuous work position pressing it and moving backward The valve s piston is Replace the v
11. olex pl The damaged sprayer not suitable for repair should be utilized in such way as not to pollute the environment Plastic elements after cleaning and removing metal parts should be taken to the utilization point These symbols on the products packaging and or on accompanying documents mean that this electrical and electronic equipment and batteries shouldn t be mixed with other household waste In order to ensure proper treatment utilization and recycling of the used devices and batteries they must be taken to collection points in accordance with local regulations and the Directives 2002 96 EC and 2006 66 EC Correct disposal of these products and batteries help to save valuable natural resources and prevent any potential negative effects on human health and the environment Information about collection points and recycling of electrical products and batteries can be obtained from your local municipality waste treatment plant or in the place of purchase Incorrect disposal of such waste can result in penalties according to the local law regulations These symbols are valid only in the European Union To utilize the electrical and electronic equipment please contact your local authorities or dealer and ask for the correct method of treating this waste 9 The warranty period is 24 months from the date of purchase except for the pump with motor battery with charger for which the warranty period is 12 months
12. s Sign Description Location Sign indicating possibility of unspecified danger On the container Sign indicating that a users manual should be read before starting work Warning against poisoning by toxic substances On the container Devices may not be disposed of with household waste used sprayer should be disposed of On the container through a recycling center Pb The battery used in this product contains lead the used or damaged battery must be disposed On the battery of through a recycling center Declaration of conformity DoC Marolex Sp z o o declares that the battery sprayer VX is in conformity with the requirements of the Directive 2006 42 EC and 73 23 EEC Battery sprayer VX Total container capacity 22 00 Working container capacity 20 00 Pump performance Maximum working pressure Overpressure protection Net weight Container material Battery Pump Diaphragm pump 12V 0 7A Working mode Interval operation Battery charger AC 100 240V 50 60 Hz DC18V 15 A Construction and maintenance of APS system in telescopic lance Telescopic lance is a piece of equipment of sprayer VX with the folded length of 60cm and after ejection of the inside lance it extends to 108 cm To get the correct length of the lance loosen the sleeve R103 pull out the inside lance A to the desired length and t
13. t When working with plant protection chemicals including preparation of the formula and utilization of the packaging it is necessary to use special protective clothing rubber boots gloves coat cap goggles mask or respirator It s forbidden to work on an empty stomach and eat drink or smoke while spraying The alcohol shouldn t be drunk before or just after spraying Residual liquid must not be released into the open water or biological waste water treatment plant Observe the applicable Ordinance of the Minister of Agriculture and Rural Development of 24 June 2002 on hygiene and safety when working with plant protection chemicals These comments also apply to rinsing the tank and other elements of the sprayer The used sprayer should be utilized in chemical waste plant In case of poisoning contact your doctor immediately Prepare spraying liquid in a special container strictly following rules given by its manufacturer It s forbidden to operate the sprayer if there are any damages or leakages Repairs must be done when the sprayer is decompressed and not contaminated Thoroughly wash sprayer after each use and before service Do not use the sprayer for other purposes than those specified in the manual The sprayer must be stored empty without any liquid in the container or lance The only device for making pressure in the container is the sprayer s pump lit s forbidden to use any other equipment for this purpose Compan
14. y Marolex does not allow the use of fluids defined as explosive extremely flammable highly flammable flammable in case when the maximum allowable temperature is above flashpoint very toxic toxic oxidising Unauthorized changes to the sprayer and using it against its purpose can lead to poisoning of humans and animals environmental contamination damage to the sprayer or serious accidents After finishing work change clothes clean protective clothing wash your hands and face rinse the mouth and throat clean the nose After finishing spraying water down the remaining liquid at least 10 times and spray it on the same area again After finishing work wash the sprayer few times with water then pour the water out and blow air through it by pumping through it a few times with the feeding valve RO20j open For the damages caused by not complying to the rules in this manual the user is fully responsible Storing of the sprayer filled with a liquid or air under pressure in forbidden It s forbidden to block the safety valve as it may cause damages After the compression the container must not be hit or dropped We recommend that you fill in the tank using our funnel with strainer built in filter additionally prevents clogging of the nozzles During use and storage the sprayer must be protected against using it by unauthorized persons especially children Sprayer once used for plant protection chemicals can not be used for other purpose
Download Pdf Manuals
Related Search